SAR APPENDIX C3

FCC ID: EJE-WL0029

RF Exposure Info

Download: PDF
FCCID_1793730

DASY5 Validation Report for Body Date/Time: 09.12.2010 13:23:23 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN:724 Communication System: CW; Frequency: 2450 MHz; Duty Cycle: 1: 1 Medium: MSL U12 BB Medium parameters used: £ = 2450 MHz; 0 = 1.92 mho/m; &= 52.5; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASYS5 Configuration: Probe: ES3DV3 — SN3205; ConvF(4.31, 4.31, 4.31); Calibrated: 30.04.2010 Sensor—Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 $n601; Calibrated: 10.06.2010 Phantom: Flat Phantom 5.0 (back); Type: QDOOOP50AA; Serial: 1002 Measurement SW: DASY52, V52.2 Build 0, Version 52.2.0 (163) Postprocessing SW: SEMCAD X, V14.2 Build 2, Version 14.2.2 (1685) Pin=250 mW /d=10mm, dist=3.0mm (ES—Probe)/Zoom Scan (7x7x7) /Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 97.3 V/m; Power Drift = —0.059 dB Peak SAR (extrapolated) = 27.3 W/kg SAR(1 g) = 13 mW/g; SAR(10 g) = 6.04 mW/g Maximum value of SAR (measured) = 17.2 mW/g 48 0 dB = 17.2mW/g Certificate No: D2450V2—724_Dec10 Page 5 of 6

Impedance Measurement Plot for Body TSL 9 Dec 2010 10:54:44 CHI sii 4 uo ors 3: 48.301 a 4.3281 o 28116 pH 2 450.000 000 MHz * De1 Ca y fivg 16 + CH2 Ca Av 16° 1 TART 2 250.000 0B MHz Certificate No: D2450V2—724_Dec10 Page 6 of 6

28 June 2012 CRA sii i.een us 41 49.400 a S.4144 0. 354.70 pH 2450.000 000 nz Ap HoLD Del SINGLE Cor PRa NUNBER of srours Av 159 conTINuous Hid CH2 TRIGGER: Trie orr Ser ext tere O SHEEP PRm I m EXT TRIG v 16° on Poxlrn- Hid naMUAL. TRe on PorhT sTaRt 2 250.000 000 MHz stor 2 sse.a0e 00e hiz p NATA

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client EMC Technologies Certificate No: DAE3—442_Dec11 [CALIBRATION CERTIFICATE Object DAE3 — SD 000 DO3 AE — SN: 442 Calibration procedure(s) QA CAL—06.v23 Calibration procedure for the data acquisition electronics (DAE) Calibration date: December 5, 2011 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Keithley Multimeter Type 2001 SN: 0810278 28—Sep—11 (No:11450) Sep—12 Secondary Standards ID # Check Date (in house) Scheduled Check Calibrator Box V1.1 SE UMS 006 AB 1004 08—Jun—11 (in house check) In house check: Jun—12 Name Function Signature _ Calibrated by: Andrea Guntli Technician j’ % _Aetlll Approved by: Fin Bomholt R&D Director L a¥ IQQ (QMAU Issued: December 5, 2011 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: DAE3—442_Dec11 Page 1 of 5 Auresutce No: sn

Calibration Laboratory of ‘\\\\‘&'@> S Schweizerischer Kalibrierdienst S mz Schmid & Partner i'E:\_/!53: c Service suisse d‘étalonnage Engineering AG yzz— o. Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland /'/,l///_\\\ w S Swiss Calibration Service thitabs®" Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service Is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters e DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. e Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. * The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. e DC Voltage Measurement Linearity: Veritication of the Linearity at +10% and —10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. e Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. e Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. e AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage e Input Offset Measurement. Output voltage and statistical results over a large number of zero voltage measurements. * Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. e Input resistance: Typical value for information: DAE input resistance at the connector, during internal auto—zeroing and during measurement. e Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signal is generated. + Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE3—442_Dec11 Page 2 of 5

DC Voltage Measurement A/D — Converter Resolution nominal High Range: 1LSB = 6.AuV , full range = ~100...+300 mV Low Range: 1LSB= 61nV , full range = Bossiesé +3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors X Y Z High Range 404.367 + 0.1%(k=2) 405.009 + 0.1% (k=2) 405.229 + 0.1% (k=2) Low Range 3.98363 £ 0.7% (k=2) 3.98114 £0.7% (k=2) 3.98948 + 0.7% (k=2) Connector Angle Connector Angle to be used in DASY system §7.0°%1" Certificate No: DAE3—442_Dec11 Page 3 of 5 Acrestie No se

Appendix 1. DC Voltage Linearity High Range Reading (uV) Difference (1V) Error (%) Channel X + Input 200002.2 —0.05 0.00 Channel X + Input 20000.16 0.66 0.00 Channel X — Input —~19997.14 2.86 —0.01 Channel Y + Input 200008.3 215 —0.00 Channel Y + Input 19996.72 —2.68 —0.01 Channel Y — Input ~19998.92 0.08 —0.00 Channel Z + Input 200008.5 —0.80 —0.00 Channel Z + Input 20000.01 —0.09 —0.00 Channel Z — Input —19998.00 1.90 —0.01 Low Range Reading (1V) Difference (uV) Error (%) Channel X + Input 1999.8 —0.20 —0.01 Channel X + Input 200.22 0.22 0.11 Channel X — Input ~198.99 1.01 —0.50 Channel Y + Input 2000.6 0.94 0.05 Channel Y + Input 199.59 —0.51 —0.26 Channel Y — Input —200.74 —0.84 0.42 Channel Z + Input 2000.0 —0.14 —0.01 Channel Z + Input 198.71 ~1.29 —0.64 Channel Z — Input ~200.84 —0.94 0.47 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Common mode High Range Low Range Input Voltage (mV) Average Reading (uV) Average Reading (1V) Channel X 200 —8.70 —10.53 — 200 11.41 10.05 Channel Y 200 0.01 —0.31 —200 ~1.37 ~1.76 Channel Z 200 5.64 5.59 ~200 3.08 5.29 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input Voltage (mV) Channel X (uV) Channel Y (uV) Channel Z (1V) Channel X 200 — 1.76 ~1.72 Channel Y 200 1.76 — 1.74 Channel Z 200 2.90 —0.48 — Certificate No: DAE3—442_Dec11 Page 4 of 5

4. AD—Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec High Range (LSB) Low Range (LSB) Channel X 15778 16839 Channel Y 19772 16308 Channel Z 15590 16770 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input 10MQ Average (uV) min. Offset (uV) max. Offset (uv) °** ?:\)’;am“ Channel X —0.87 —2.04 0.18 0.54 Channel Y —1.01 —2.34 —0.08 0.42 Channel Z —1.28 —3.05 1.11 0.70 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25fA 7. Input Resistance (Typical values for information) Zeroing (kOhm) Measuring (MOhm) Channel X 200 200 Channel Y 200 200 Channel Z 200 200 8. Low Battery Alarm Voltage (Typical values for information) Typical values Alarm Level (VDC) Supply (+ Vee) +7.9 Supply (— Vee) —7.6 9. Power Consumption (Typical values for information) Typical values Switched off (mA) Stand by (mA) Transmitting (mA) Supply (+ Vee) +0.01 +6 +14 Supply (— Vee) —0.01 —8 —9 Certificate No: DAE3—442_Dec11 Page 5 of 5


Document Created: 2019-06-19 12:09:41
Document Modified: 2019-06-19 12:09:41
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC