Test Report

FCC ID: E8HRG-0983

Test Report

Download: PDF
FCCID_1266563

FCC TEST REPORT REPORT NO.: RF990319D15-2 MODEL NO.: RG-0983 RECEIVED: March 22, 2010 TESTED: March 22 ~ 29, 2010 ISSUED: April 1, 2010 APPLICANT: Chicony Electronics Co., Ltd. ADDRESS: No. 25, Wu-Gong 6th Rd., Wu Ku Industrial Park, Taipei Hsien, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien, 244 Taiwan This test report consists of 29 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF990319D15-2 1 Report Format Version 3.0.1

Table of Contents 1. CERTIFICATION ..........................................................................................3 2. SUMMARY OF TEST RESULTS..................................................................4 2.1 MEASUREMENT UNCERTAINTY...............................................................4 3. GENERAL INFORMATION ..........................................................................5 3.1 GENERAL DESCRIPTION OF EUT ............................................................5 3.2 DESCRIPTION OF TEST MODES ..............................................................6 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST .........................................6 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL: .............7 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS .............................8 3.4 DESCRIPTION OF SUPPORT UNITS ........................................................8 4. TEST TYPES AND RESULTS......................................................................9 4.1 CONDUCTED EMISSION MEASUREMENT ..............................................9 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT............................9 4.1.2 TEST INSTRUMENTS ................................................................................9 4.1.3 TEST PROCEDURES ...............................................................................10 4.1.4 DEVIATION FROM TEST STANDARD .....................................................10 4.1.5 TEST SETUP ............................................................................................10 4.1.6 EUT OPERATING CONDITIONS ..............................................................11 4.1.7 TEST RESULTS ........................................................................................12 4.2 RADIATED EMISSION MEASUREMENT .................................................14 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT ...............................14 4.2.2 TEST INSTRUMENTS ..............................................................................15 4.2.3 TEST PROCEDURES ...............................................................................16 4.2.4 DEVIATION FROM TEST STANDARD .....................................................16 4.2.5 TEST SETUP ............................................................................................17 4.2.6 EUT OPERATING CONDITIONS ..............................................................17 4.2.7 TEST RESULTS ........................................................................................18 4.3 BAND EDGES MEASUREMENT ..............................................................24 4.3.1 LIMITS OF BAND EDGES MEASUREMENT............................................24 4.3.2 TEST INSTRUMENTS ..............................................................................24 4.3.3 TEST PROCEDURE .................................................................................24 4.3.4 DEVIATION FROM TEST STANDARD .....................................................24 4.3.5 EUT OPERATING CONDITION ................................................................24 4.3.6 TEST RESULTS ........................................................................................24 5. PHOTOGRAPHS OF THE TEST CONFIGURATION.................................27 6. INFORMATION ON THE TESTING LABORATORIES ...............................28 7. APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ......................................................29 Report No.: RF990319D15-2 2 Report Format Version 3.0.1

1. CERTIFICATION PRODUCT: Dongle BRAND NAME: hp MODEL NO.: RG-0983 APPLICANT: Chicony Electronics Co., Ltd. TESTED: March 22 ~ 29, 2010 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 15, Subpart C (Section 15.249) ANSI C63.4-2003 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: April 1, 2010 ( Annie Chang / Senior Specialist ) TECHNICAL ACCEPTANCE : , DATE: April 1, 2010 Responsible for RF ( Jamison Chan / Supervisor ) APPROVED BY : , DATE: April 1, 2010 ( Ken Liu / Assistant Manager ) Report No.: RF990319D15-2 3 Report Format Version 3.0.1

2. SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 15, Subpart C (Section 15.249) STANDARD TEST TYPE AND LIMIT RESULT REMARK SECTION Minimum passing margin is 15.207 Conducted Emission Test PASS –14.47dB at 0.173MHz Radiated Emission Test Band Edge Measurement 15.209 Limit: 50dB less than the Minimum passing margin is 15.249 peak value of fundamental PASS –8.8dB at 2390.00MHz 15.249 (d) frequency or meet radiated emission limit in section 12.209 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Measurement Frequency Uncertainty Conducted emissions 9kHz ~ 30MHz 2.41 dB 30MHz ~ 1GHz 3.67 dB Radiated emissions Above 1GHz 2.89 dB Report No.: RF990319D15-2 4 Report Format Version 3.0.1

3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT EUT Dongle MODEL NO. RG-0983 FCC ID E8HRG-0983 POWER SUPPLY 5Vdc from host equipment MODULATION TYPE GFSK OPERATING FREQUENCY 2403MHz ~ 2480MHz NUMBER OF CHANNEL 78 ANTENNA TYPE Strip antenna with –0.05dBi gain ANTENNA CONNECTOR N/A DATA CABLE N/A I/O PORTS USB port ASSOCIATED DEVICES N/A NOTE: 1. The EUT is a transceiver. 2. The above EUT information was declared by the manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report No.: RF990319D15-2 5 Report Format Version 3.0.1

3.2 DESCRIPTION OF TEST MODES 78 channels are provided to this EUT: FREQ. FREQ. FREQ. FREQ. CHANNEL CHANNEL CHANNEL CHANNEL (MHZ) (MHz) (MHz) (MHz) 1 2403 21 2423 41 2443 61 2463 2 2404 22 2424 42 2444 62 2464 3 2405 23 2425 43 2445 63 2465 4 2406 24 2426 44 2446 64 2466 5 2407 25 2427 45 2447 65 2467 6 2408 26 2428 46 2448 66 2468 7 2409 27 2429 47 2449 67 2469 8 2410 28 2430 48 2450 68 2470 9 2411 29 2431 49 2451 69 2471 10 2412 30 2432 50 2452 70 2472 11 2413 31 2433 51 2453 71 2473 12 2414 32 2434 52 2454 72 2474 13 2415 33 2435 53 2455 73 2475 14 2416 34 2436 54 2456 74 2476 15 2417 35 2437 55 2457 75 2477 16 2418 36 2438 56 2458 76 2478 17 2419 37 2439 57 2459 77 2479 18 2420 38 2440 58 2460 78 2480 19 2421 39 2441 59 2461 20 2422 40 2442 60 2462 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST EUT (Dongle) (Powered from host equipment) Modem Notebook Printer Adapter Test Table Report No.: RF990319D15-2 6 Report Format Version 3.0.1

3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL: EUT Applicable to configure Description mode PLC RE<1G RE≥1G BM - √ √ √ √ - Where PLC: Power Line Conducted Emission RE<1G RE: Radiated Emission below 1GHz RE≥1G: Radiated Emission above 1GHz BM: Bandedge Measurement POWER LINE CONDUCTED EMISSION TEST: Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 to 78 1 GFSK RADIATED EMISSION TEST (BELOW 1 GHz):  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 to 78 1 GFSK RADIATED EMISSION TEST (ABOVE 1 GHz):  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 to 78 1, 39, 78 GFSK BANDEDGE MEASUREMENT:  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 to 78 1, 78 GFSK Report No.: RF990319D15-2 7 Report Format Version 3.0.1

TEST CONDITION: APPLICABLE INPUT POWER TO ENVIRONMENTAL CONDITIONS TESTED BY (SYSTEM) PLC 18deg. C, 65% RH, 1023hPa 120Vac, 60Hz Chad Lee RE<1G 16deg. C, 56% RH, 1024hPa 120Vac, 60Hz Chad Lee RE≥1G 16deg. C, 56% RH, 1024hPa 120Vac, 60Hz Chad Lee BM 20deg. C, 80% RH, 1014hPa 120Vac, 60Hz Chad Lee 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RF product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C. (15.249) ANSI C63.4-2003 All test items have been performed and recorded as per the above standards. NOTE: The product has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. 3.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID NOTEBOOK 1 DELL PP05L 20375526736 FCC DoC Approved COMPUTER 2 PRINTER EPSON LQ-300+ DCGY017054 FCC DoC Approved 3 MODEM ACEEX 1414 980020520 IFAXDM1414 NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS 1 N/A 1.8m braid shielded wire, terminated with DB25 and Centronics connector via metallic 2 frame, w/o core 1.2 m braid shielded wire, terminated with DB25 and DB9 connector via metallic frame, 3 w/o core. NOTE: All power cords of the above support units are non-shielded (1.8m). Report No.: RF990319D15-2 8 Report Format Version 3.0.1

4. TEST TYPES AND RESULTS 4.1 CONDUCTED EMISSION MEASUREMENT 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT FREQUENCY OF EMISSION (MHz) CONDUCTED LIMIT (dBµV) Quasi-peak Average 0.15-0.5 66 to 56 56 to 46 0.5-5 56 46 5-30 60 50 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. 4.1.2 TEST INSTRUMENTS DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL ROHDE & SCHWARZ ESCS 30 100276 Dec. 15, 2009 Dec. 14, 2010 Test Receiver ROHDE & SCHWARZ Artificial Mains Network ESH3-Z5 100218 Nov. 24, 2009 Nov. 23, 2010 (for EUT) LISN With Adapter AD10 C10Ada-001 Nov. 24, 2009 Nov. 23, 2010 (for EUT) ROHDE & SCHWARZ Artificial Mains Network ESH3-Z5 100219 Nov. 23, 2009 Nov. 22, 2010 (for peripherals) Software ADT_Cond_V7.3.7 NA NA NA Software ADT_ISN_V7.3.7 NA NA NA RF cable (JYEBAO) 5D-FB Cable-C10.01 Feb. 23, 2010 Feb. 22, 2011 SUHNER Terminator (For ROHDE & 65BNC-5001 E1-010773 Feb. 23, 2010 Feb. 22, 2011 SCHWARZ LISN) NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Shielded Room No. 10. 3. The VCCI Site Registration No. C-1852. Report No.: RF990319D15-2 9 Report Format Version 3.0.1

4.1.3 TEST PROCEDURES a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under limit - 20dB was not recorded. 4.1.4 DEVIATION FROM TEST STANDARD No deviation. 4.1.5 TEST SETUP V e r tic a l G r o u n d R e f e r e n c e P la n e T e s t R e c e iv e r EUT 40cm 80cm L IS N H o r iz o n t a l G r o u n d R e fe r e n c e P la n e N o t e : 1 .S u p p o r t u n its w e r e c o n n e c te d to s e c o n d L IS N . 2 .B o t h o f L IS N s (A M N ) a r e 8 0 c m fr o m E U T a n d a t le a s t 8 0 fr o m o th e r u n its a n d o th e r m e ta l p la n e s For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. Report No.: RF990319D15-2 10 Report Format Version 3.0.1

4.1.6 EUT OPERATING CONDITIONS a. Connected the EUT to a notebook placed on a testing table. b. The notebook ran a test program (provided by manufacturer) to enable EUT under transmission/receiving condition continuously at specific channel frequency. c. The notebook sent messages to printer and the printer printed them out. d. The notebook sent messages to modem. e. Repeated c ~ e. Report No.: RF990319D15-2 11 Report Format Version 3.0.1

4.1.7 TEST RESULTS CONDUCTED WORST CASE DATA PHASE Line 1 6dB BANDWIDTH 9 kHz Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.150 0.19 43.13 - 43.32 - 66.00 56.00 -22.68 - 2 0.173 0.19 50.14 - 50.33 - 64.80 54.80 -14.47 - 3 0.259 0.22 41.79 - 42.01 - 61.47 51.47 -19.46 - 4 2.006 0.34 26.30 - 26.64 - 56.00 46.00 -29.36 - 5 9.746 0.70 27.95 - 28.65 - 60.00 50.00 -31.35 - 6 14.160 0.98 23.38 - 24.36 - 60.00 50.00 -35.64 - REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: RF990319D15-2 12 Report Format Version 3.0.1

PHASE Line 2 6dB BANDWIDTH 9 kHz Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.150 0.29 44.18 - 44.47 - 66.00 56.00 -21.53 - 2 0.173 0.29 49.05 - 49.34 - 64.79 54.79 -15.46 - 3 0.259 0.31 41.83 - 42.14 - 61.45 51.45 -19.31 - 4 0.873 0.39 26.46 - 26.85 - 56.00 46.00 -29.15 - 5 9.995 0.70 28.69 - 29.39 - 60.00 50.00 -30.61 - 6 14.397 0.90 23.65 - 24.55 - 60.00 50.00 -35.45 - REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: RF990319D15-2 13 Report Format Version 3.0.1

4.2 RADIATED EMISSION MEASUREMENT 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT Emissions radiated outside of the specified bands, shall be according to the general radiated limits in 15.209, 15.249 as following: 15.209 Limit Frequencies Field strength Measurement distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 15.249 Limit Field Strength of Field Strength of Fundamental Fundamental Harmonics Frequency (millivolts/meter) (microvolts/meter) 902 ~ 928 MHz 50 500 2400 ~ 2483.5 MHz 50 500 5725 ~ 5875 MHz 50 500 24 ~ 24.25 GHz 250 2500 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF990319D15-2 14 Report Format Version 3.0.1

4.2.2 TEST INSTRUMENTS DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL HP Preamplifier 8447D 2432A03504 May 04, 2009 May 03, 2010 HP Preamplifier 8449B 3008A01924 Aug. 31, 2009 Aug. 30, 2010 HP Preamplifier 8449B 3008A01292 Aug. 10, 2009 Aug. 09, 2010 ROHDE & SCHWARZ ESU26 100005 Jun. 06, 2009 Jun. 05, 2010 TEST RECEIVER Schwarzbeck Antenna VULB 9168 137 Apr. 29, 2009 Apr. 28, 2010 Schwarzbeck Antenna VHBA 9123 480 Apr. 21, 2009 Apr. 20, 2010 EMCO Horn Antenna 3115 6714 Oct. 26, 2009 Oct. 25, 2010 EMCO Horn Antenna 3115 9312-4192 Apr. 17, 2009 Apr. 16, 2010 ADT. Turn Table TT100 0306 NA NA ADT. Tower AT100 0306 NA NA ADT_Radiated_V Software NA NA NA 7.6.15.9.2 CABLE-CH6-17m SUHNER RF cable SF104-26.5 Aug. 20, 2009 Aug. 19, 2010 -01 ROHDE & SCHWARZ FSP 40 100036 Apr. 03, 2009 Apr. 02, 2010 Spectrum Analyzer NOTE: 1. The calibration interval of the above test instruments is 12/24 months. And the calibrations are traceable to NML/ROC and NIST/USA. 2. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 3. The test was performed in Chamber No. 6. 4. The Industry Canada Reference No. IC 7450E-6. 5. The FCC Site Registration No. is 447212. Report No.: RF990319D15-2 15 Report Format Version 3.0.1

4.2.3 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi- anechoic chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. If the emission level of the EUT in peak mode was lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions would be re-tested one by one using peak, quasi-peak method or average method as specified and then reported in data sheet. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and video bandwidth is 3MHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is 10Hz for Average detection (AV) at frequency above 1GHz. 4. All modes of operation were investigated and the worst-case emissions are reported. 4.2.4 DEVIATION FROM TEST STANDARD No deviation Report No.: RF990319D15-2 16 Report Format Version 3.0.1

4.2.5 TEST SETUP Ant. Tower 1-4m Variable 3m EUT& Support Units Turn Table 80cm Ground Plane Test Receiver For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 4.2.6 EUT OPERATING CONDITIONS Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF990319D15-2 17 Report Format Version 3.0.1

4.2.7 TEST RESULTS ABOVE 1GHz DATA EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 FREQUENCY RANGE 1 ~ 25GHz INPUT POWER DETECTOR Peak (PK) 120Vac, 60Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 16deg. C, 56% RH TESTED BY Chad Lee CONDITIONS 1024hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 2390.00 65.2 PK 74.0 -8.8 1.00 H 16 33.61 31.55 2 2390.00 44.4 AV 54.0 -9.6 1.00 H 16 12.86 31.55 3 2400.00 55.5 PK 74.0 -18.5 1.00 H 16 23.93 31.59 4 2400.00 31.5 AV 54.0 -22.5 1.00 H 16 -0.04 31.59 5 *2403.00 97.4 PK 114.0 -16.6 1.00 H 16 65.84 31.60 6 *2403.00 73.4 AV 94.0 -20.6 1.00 H 16 41.87 31.60 7 4806.00 49.4 PK 74.0 -24.6 1.09 H 23 11.77 37.67 8 4806.00 25.4 AV 54.0 -28.6 1.09 H 23 -12.20 37.67 9 7209.00 52.6 PK 74.0 -21.4 1.00 H 63 8.81 43.78 10 7209.00 28.6 AV 54.0 -25.4 1.00 H 63 -15.16 43.78 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “ * “ : Fundamental frequency 6. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 20 log (Duty cycle) = 20 log (0.2 ms / 3.16 ms) = -24.0 dB Please see page 22 for plotted duty. Report No.: RF990319D15-2 18 Report Format Version 3.0.1

EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 FREQUENCY RANGE 1 ~ 25GHz INPUT POWER DETECTOR Peak (PK) 120Vac, 60Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 16deg. C, 56% RH TESTED BY Chad Lee CONDITIONS 1024hPa ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 2390.00 59.4 PK 74.0 -14.6 1.00 V 0 27.83 31.55 2 2390.00 44.5 AV 54.0 -9.5 1.00 V 0 12.96 31.55 3 2400.00 51.3 PK 74.0 -22.7 1.00 V 0 19.74 31.59 4 2400.00 27.3 AV 54.0 -26.7 1.00 V 0 -4.23 31.59 5 *2403.00 93.3 PK 114.0 -20.7 1.00 V 0 61.65 31.60 6 *2403.00 69.3 AV 94.0 -24.7 1.00 V 0 37.68 31.60 7 4806.00 51.9 PK 74.0 -22.1 1.13 V 142 14.19 37.67 8 4806.00 27.9 AV 54.0 -26.1 1.13 V 142 -9.78 37.67 9 7209.00 53.8 PK 74.0 -20.2 1.00 V 16 10.05 43.78 10 7209.00 29.8 AV 54.0 -24.2 1.00 V 16 -13.92 43.78 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “ * “ : Fundamental frequency 6. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 20 log (Duty cycle) = 20 log (0.2 ms / 3.16 ms) = -24.0 dB Please see page 22 for plotted duty. Report No.: RF990319D15-2 19 Report Format Version 3.0.1

EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 39 FREQUENCY RANGE 1 ~ 25GHz INPUT POWER DETECTOR Peak (PK) 120Vac, 60Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 16deg. C, 56% RH TESTED BY Chad Lee CONDITIONS 1024hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 *2441.00 95.7 PK 114.0 -18.3 1.00 H 28 63.93 31.75 2 *2441.00 71.7 AV 94.0 -22.3 1.00 H 28 39.96 31.75 3 4882.00 50.8 PK 74.0 -23.2 1.00 H 16 12.82 37.94 4 4882.00 26.8 AV 54.0 -27.2 1.00 H 16 -11.15 37.94 5 7323.00 51.8 PK 74.0 -22.2 1.05 H 113 7.58 44.18 6 7323.00 27.8 AV 54.0 -26.2 1.05 H 113 -16.39 44.18 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 *2441.00 93.5 PK 114.0 -20.5 1.00 V 2 61.77 31.75 2 *2441.00 69.5 AV 94.0 -24.5 1.00 V 2 37.80 31.75 3 4882.00 51.7 PK 74.0 -22.3 1.00 V 153 13.75 37.94 4 4882.00 27.7 AV 54.0 -26.3 1.00 V 153 -10.22 37.94 5 7323.00 53.3 PK 74.0 -20.7 1.00 V 66 9.16 44.18 6 7323.00 29.3 AV 54.0 -24.7 1.00 V 66 -14.81 44.18 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “ * “ : Fundamental frequency 6. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 20 log (Duty cycle) = 20 log (0.2 ms / 3.16 ms) = -24.0 dB Please see page 22 for plotted duty. Report No.: RF990319D15-2 20 Report Format Version 3.0.1

EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 78 FREQUENCY RANGE 1 ~ 25GHz INPUT POWER DETECTOR Peak (PK) 120Vac, 60Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 16deg. C, 56% RH TESTED BY Chad Lee CONDITIONS 1024hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 *2480.00 94.9 PK 114.0 -19.1 1.14 H 16 63.04 31.89 2 *2480.00 70.9 AV 94.0 -23.1 1.14 H 16 39.07 31.89 3 2483.50 51.5 PK 74.0 -22.5 1.14 H 16 19.60 31.91 4 2483.50 27.5 AV 54.0 -26.5 1.14 H 16 -4.37 31.91 5 4960.00 46.4 PK 74.0 -27.6 1.00 H 66 8.27 38.10 6 4960.00 22.4 AV 54.0 -31.6 1.00 H 66 -15.70 38.10 7 7440.00 54.7 PK 74.0 -19.3 1.00 H 29 10.23 44.48 8 7440.00 30.7 AV 54.0 -23.3 1.00 H 29 -13.74 44.48 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 *2480.00 93.8 PK 114.0 -20.2 1.00 V 300 61.90 31.89 2 *2480.00 69.8 AV 94.0 -24.2 1.00 V 300 37.93 31.89 3 2483.50 50.4 PK 74.0 -23.6 1.00 V 300 18.46 31.91 4 2483.50 26.4 AV 54.0 -27.6 1.00 V 300 -5.51 31.91 5 4960.00 52.6 PK 74.0 -21.4 1.00 V 143 14.48 38.10 6 4960.00 28.6 AV 54.0 -25.4 1.00 V 143 -9.49 38.10 7 7440.00 55.0 PK 74.0 -19.0 1.00 V 172 10.52 44.48 8 7440.00 31.0 AV 54.0 -23.0 1.00 V 172 -13.45 44.48 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “ * “ : Fundamental frequency 6. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 20 log (Duty cycle) = 20 log (0.2 ms / 3.16 ms) = -24.0 dB Please see page 22 for plotted duty. Report No.: RF990319D15-2 21 Report Format Version 3.0.1

20 log (Duty cycle) = 20 log (0.2 ms / 3.16 ms) = -24.0 dB Report No.: RF990319D15-2 22 Report Format Version 3.0.1

BELOW 1GHz WORST-CASE DATA EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 FREQUENCY RANGE Below 1000MHz INPUT POWER DETECTOR 120Vac, 60Hz Quasi-Peak (SYSTEM) FUNCTION ENVIRONMENTAL 16deg. C, 56% RH TESTED BY Chad Lee CONDITIONS 1024hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 177.68 30.3 QP 43.5 -13.2 1.50 H 97 17.18 13.08 2 451.27 30.2 QP 46.0 -15.8 1.00 H 94 10.50 19.66 3 532.10 32.2 QP 46.0 -13.8 1.50 H 325 10.38 21.81 4 598.94 31.5 QP 46.0 -14.5 1.50 H 94 8.30 23.20 5 732.63 33.6 QP 46.0 -12.4 1.00 H 325 8.12 25.45 6 861.65 33.8 QP 46.0 -12.2 1.50 H 283 6.22 27.55 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 36.22 28.6 QP 40.0 -11.4 1.00 V 10 16.06 12.58 2 73.53 28.0 QP 40.0 -12.0 1.50 V 226 16.68 11.32 3 110.83 32.8 QP 43.5 -10.7 1.50 V 10 22.53 10.23 4 451.27 34.4 QP 46.0 -11.6 1.00 V 148 14.71 19.66 5 732.63 33.7 QP 46.0 -12.3 1.50 V 10 8.25 25.45 6 864.76 33.4 QP 46.0 -12.6 1.50 V 319 5.78 27.59 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. Report No.: RF990319D15-2 23 Report Format Version 3.0.1

4.3 BAND EDGES MEASUREMENT 4.3.1 LIMITS OF BAND EDGES MEASUREMENT Below –50dB of the highest emission level of operating band (in 100kHz Resolution Bandwidth). 4.3.2 TEST INSTRUMENTS Description & Calibrated Calibrated Model No. Serial No. Manufacturer Date Until SPECTRUM ANALYZER FSP 40 100036 Apr. 03, 2009 Apr. 02, 2010 NOTE: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 4.3.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer via a low lose cable. Set both RBW and VBW of spectrum analyzer to 100 kHz and 300 kHz with suitable frequency span including 100 MHz bandwidth from band edge. The band edges was measured and recorded. The spectrum plots are attached on the following pages. 4.3.4 DEVIATION FROM TEST STANDARD No deviation 4.3.5 EUT OPERATING CONDITION Same as Item 4.2.6 4.3.6 TEST RESULTS The spectrum plots are attached on the following 4 images. D1 line indicates the highest level, and D2 line indicates the 50dB offset below D1. It shows compliance with the requirement in part 15.249(d). Report No.: RF990319D15-2 24 Report Format Version 3.0.1

Report No.: RF990319D15-2 25 Report Format Version 3.0.1

Report No.: RF990319D15-2 26 Report Format Version 3.0.1

5. PHOTOGRAPHS OF THE TEST CONFIGURATION Please refer to the attached file (Test Setup Photo). Report No.: RF990319D15-2 27 Report Format Version 3.0.1

6. INFORMATION ON THE TESTING LABORATORIES We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26051924 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3185050 Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report No.: RF990319D15-2 28 Report Format Version 3.0.1

7. APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No any modifications are made to the EUT by the lab during the test. ---END--- Report No.: RF990319D15-2 29 Report Format Version 3.0.1


Document Created: 2010-04-06 12:12:40
Document Modified: 2010-04-06 12:12:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC