RF Exposure Information (MPE) rev

FCC ID: E8HMG-1638

RF Exposure Info

Download: PDF
FCCID_3235469

RF Exposure Report Report No.: SA161125D29 FCC ID: E8HMG-1638 Test Model: MG-1638 Received Date: Nov. 25, 2016 Test Date: Nov. 28, 2016 Issued Date: Dec. 6, 2016 Applicant: Chicony Electronics Co., Ltd. Address: No.69, Sec. 2, Guangfu Rd., Sanchong Dist., New Taipei City 241, Taiwan(R.O.C.) Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan (R.O.C.) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA161125D29 Page No. 1 / 6 Report Format Version: 6.1.1

Table of Contents Release Control Record .................................................................................................................................... 3 1 Certificate of Conformity ......................................................................................................................... 4 2 Evaluation Result .................................................................................................................................... 5 3 SAR Test Exclusion Thresholds .............................................................................................................. 6 4 Conclusion .............................................................................................................................................. 6 Report No.: SA161125D29 Page No. 2 / 6 Report Format Version: 6.1.1

Release Control Record Issue No. Description Date Issued SA161125D29 Original release. Dec. 6, 2016 Report No.: SA161125D29 Page No. 3 / 6 Report Format Version: 6.1.1

1 Certificate of Conformity Product: Wireless Mouse Brand: ASUS Test Model: MG-1638 Sample Status: Engineering sample Applicant: Chicony Electronics Co., Ltd. Test Date: Nov. 28, 2016 Standards: FCC Part 2 (Section 2.1093) KDB 447498 D01 General RF Exposure Guidance v06 IEEE C95.1-1992 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: Dec. 6, 2016 Annie Chang / Senior Specialist Approved by : , Date: Dec. 6, 2016 Rex Lai / Assistant Manager Report No.: SA161125D29 Page No. 4 / 6 Report Format Version: 6.1.1

2 Evaluation Result Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz.  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Report No.: SA161125D29 Page No. 5 / 6 Report Format Version: 6.1.1

3 SAR Test Exclusion Thresholds Maximum measured transmitter power: Max. Max. Min. test SAR test 1-g SAR test Frequency Radiated Radiated separation exclusion exclusion Result (GHz) Power Power distance calculation thresholds (dBuV/m) (mW) (mm) value(NOTE 2) 2.403 ~ 2.480 93.8 0.720 5 0.223 3 Pass NOTE: 1. The antenna type is Printed antenna with 1.53dBi gain. 2. Calculate SAR test exclusion thresholds from condition “1” formulas. 4 Conclusion Since Source-base time average power is below SAR test exclusion power thresholds, the SAR evaluation is not required. --- END --- Report No.: SA161125D29 Page No. 6 / 6 Report Format Version: 6.1.1


Document Created: 2017-12-19 22:38:35
Document Modified: 2017-12-19 22:38:35
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC