Test report 1 of 2

FCC ID: E2K-DWRFID1401

Test Report

Download: PDF
FCCID_2453246

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP FCC 47 CFR PART 15 SUBPART C (Class II Permissive Change) TEST REPORT For RFID 13.56MHz Wireless Module Model: DWRFID1401 Trade Name: DELL Issued to Dell Inc. One Dell Way Round Rock Texas 78682 United States Issued by Compliance Certification Services Inc. No.11, Wugong 6th Rd., Wugu Dist., New Taipei City 24891, Taiwan. (R.O.C.) http://www.ccsrf.com service@ccsrf.com Issued Date: April 24, 2014 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 / 29

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP Revision History Issue Effect Rev. Date Revisions Page Revised By 00 April 24, 2014 Initial Issue ALL Kelly Cheng Page 2

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ............................................................................................. 4 2. EUT DESCRIPTION .................................................................................................................... 5 3. TEST METHODOLOGY ............................................................................................................. 6 3.1 EUT CONFIGURATION .............................................................................................................. 6 3.2 EUT EXERCISE ......................................................................................................................... 6 3.3 GENERAL TEST PROCEDURES .................................................................................................. 6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS .............................................. 7 3.5 DESCRIPTION OF TEST MODES ................................................................................................. 7 4. INSTRUMENT CALIBRATION ................................................................................................. 8 4.1 MEASURING INSTRUMENT CALIBRATION ........................................................................... 8 4.2 MEASUREMENT EQUIPMENT USED .............................................................................. 8 4.3 MEASUREMENT UNCERTAINTY .................................................................................... 9 5. FACILITIES AND ACCREDITATIONS ................................................................................. 10 5.1 FACILITIES ............................................................................................................................ 10 5.2 EQUIPMENT ........................................................................................................................... 10 5.3 TABLE OF ACCREDITATIONS AND LISTINGS .......................................................................... 11 6. SETUP OF EQUIPMENT UNDER TEST ................................................................................ 12 6.1 SETUP CONFIGURATION OF EUT ............................................................................................ 12 6.2 SUPPORT EQUIPMENT..................................................................................................... 12 7. FCC PART 15.225 REQUIREMENTS...................................................................................... 13 7.1 20 DB BANDWIDTH .......................................................................................................... 13 7.2 RADIATED EMISSIONS ........................................................................................................... 15 7.3 FREQUENCY STABILITY ........................................................................................................ 21 7.4 POWERLINE CONDUCTED EMISSIONS .................................................................................... 23 APPENDIX I PHOTOGRAPHS OF TEST SETUP ....................................................................... 26 APPENDIX 1 - PHOTOGRAPHS OF EUT Page 3

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 1. TEST RESULT CERTIFICATION Applicant: Dell Inc. One Dell Way Round Rock Texas 78682 United States Equipment Under Test: RFID 13.56MHz Wireless Module Trade Name: DELL Model: DWRFID1401 Date of Test: April 22 ~ April 24, 2014 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample tested as described in this report is in compliance with the requirements of FCC Rules Part 15.225. The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: Miller Lee Angel Cheng Section Manager Section Manager Compliance Certification Services Inc. Compliance Certification Services Inc. Page 4

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 2. EUT DESCRIPTION Product RFID 13.56MHz Wireless Module Trade Name DELL Model Number DWRFID1401 Model Difference N/A Received Date April 14, 2014 Power Supply Powered by host device. Frequency Range 13.56MHz Modulation Technique ASK Number of Channels 1 Channel Yageo / ANTA0DC08391RFID1 Antenna Designation Loop Antenna / Gain: 0 dBi The product RFID 13.56MHz Wireless Module will be installed in the following Class II Permissive Change models of notebooks/laptops: Model: P22S Product name: Notebook Computer / Brand name: DELL / Model: P22S Remark: 1. The sample selected for test was engineering sample that approximated to production product and was provided by manufacturer. 2. This submittal(s) (test report) is intended for FCC ID: E2K-DWRFID1401 filing to comply with Section 15.225 of the FCC Part 15, Subpart C Rules. Page 5

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 3. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4: 2009 and FCC CFR 47 Part 15.207, 15.209 and 15.225. 3.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. 3.3 GENERAL TEST PROCEDURES Conducted Emissions The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in Section 13.1.4.1 of ANSI C63.4: 2009. Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and average detector modes. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section 13.1.4.1 of ANSI C63.4: 2009. Page 6

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.52525 2655 - 2900 22.01 - 23.12 8.41425 - 8.41475 156.7 - 156.9 3260 - 3267 23.6 - 24.0 12.29 - 12.293 162.0125 - 167.17 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 167.72 - 173.2 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 240 - 285 3600 - 4400 (2) 13.36 - 13.41 322 - 335.4 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6 (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. 3.5 DESCRIPTION OF TEST MODES The EUT (model: DWRFID1401) had been tested under engineering test mode condition and the EUT staying in continuous transmitting mode. Page 7

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 4. INSTRUMENT CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 4.2 MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement Remark: Each piece of equipment is scheduled for calibration once a year and Loop Antenna is scheduled for calibration once three years. Wugu 966 Chamber A Name of Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer Agilent E4446A US42510268 11/05/2014 EMI Test Receiver R&S ESCI 100064 02/27/2015 Pre-Amplifier Mini-Circults ZFL-1000LN SF350700823 01/11/2015 AFS44-00102650- Pre-Amplifier MITEQ 1415367 11/18/2014 42-10P-44 Bilog Antenna Sunol Sciences JB3 A030105 10/01/2014 Horn Antenna EMCO 3117 00055165 02/12/2015 Horn Antenna EMCO 3116 2487 10/09/2014 Turn Table CCS CC-T-1F N/A N.C.R Antenna Tower CCS CC-A-1F N/A N.C.R Controller CCS CC-C-1F N/A N.C.R Site NSA CCS N/A N/A 12/21/2014 Test S/W EZ-EMC (CCS-3A1RE) Page 8

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 4.3 MEASUREMENT UNCERTAINTY PARAMETER UNCERTAINTY 3M Semi Anechoic Chamber / 30M~200M +/- 4.0138 3M Semi Anechoic Chamber / 200M~1000M +/- 3.9483 3M Semi Anechoic Chamber / 1G~8G +/- 2.5975 3M Semi Anechoic Chamber / 8G~18G +/- 2.6112 3M Semi Anechoic Chamber / 18G~26G +/- 2.7389 3M Semi Anechoic Chamber / 26G~40G +/- 2.9683 Remark: This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Page 9

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at No.199, Chunghsen Road, Hsintien City, Taipei Hsien, Taiwan, R.O.C. Tel: 886-2-2217-0894 / Fax: 886-2-2217-1029 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City 24891, Taiwan. (R.O.C.) Tel: 886-2-2299-9720 / Fax: 886-2-2298-4045 No.81-1, Lane 210, Bade 2nd Rd., Lujhu Township, Taoyuan County 33841, TAIWAN, R.O.C. Tel: 886-3-324-0332 / Fax: 886-3-324-5235 The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22. 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with pre-selectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, “Radio Interference Measuring Apparatus and Measurement Methods.” Page 10

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 5.3 TABLE OF ACCREDITATIONS AND LISTINGS Country Agency Scope of Accreditation Logo 3M Semi Anechoic Chamber (FCC MRA: TW1039) to perform USA FCC FCC Part 15 measurements FCC MRA: TW1039 LP0002, RTTE01, FCC Method-47 CFR Part 15 Subpart C, D, E, RSS-210, RSS-310 IDA TS SRD, AS/NZS 4268, AS/NZS 4771, TS 12.1 & 12,2, ETSI EN 300 440-1, ETSI EN 300 440-2, ETSI EN 300 328, ETSI EN 300 220-1, ETSI EN 300 220-2, ETSI EN 301 893, ETSI EN 301 489-1/3/7/17 Taiwan TAF FCC OET Bulletin 65 + Supplement C, EN 50360, EN 50361, EN 50371, RSS 102, EN 50383, EN 50385, EN 50392, IEC 62209, CNS 14958-1, CNS 14959 FCC Method –47 CFR Part 15 Subpart B IEC / EN 61000-3-2, IEC / EN 61000-3-3, IEC / EN 61000-4-2/3/4/5/6/8/11 Industry Canada 3M Semi Anechoic Chamber (IC 2324G-1 / IC 2324G-2) to perform IC 2324G-1 Canada IC 2324G-2 * No part of this report may be used to claim or imply product endorsement by A2LA or any agency of the US Government. Page 11

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 6. SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix I for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT No. Device Type Brand Model Series No. FCC ID Data Cable Power Cord N/A Remark: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. Page 12

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 7. FCC PART 15.225 REQUIREMENTS 7.1 20 DB BANDWIDTH LIMIT None; for reporting purposes only. Test Configuration EUT Spectrum Analyzer TEST PROCEDURE 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the spectrum analyzer as RBW= 5.1kHz, VBW = 10kHz, Span = 500kHz, Sweep = auto. 4. Mark the peak frequency and 20dB (upper and lower) frequency. 5. Repeat until all the rest channels are investigated. TEST RESULTS No non-compliance noted. Page 13

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP Test Plot Page 14

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 7.2 RADIATED EMISSIONS LIMIT According to §15.225, (a) The field strength of any emissions within the band 13.553 – 13.567 MHz shall not exceed 15,848 microvolts / meter at 30 meters. (b) Within the bands 13.410 – 13.553 MHz and 13.567 -13.710 MHz, the field strength of any emissions shall not exceed 334 microvolts / meter at 30 meters. (c) Within the bands 13.110 – 13.410 MHz and 13.710 – 14.010 MHz the field strength of any emissions shall not exceed 106 microvolts / meter at 30 meters. (d) The field strength of any emissions appearing outside of the 13.110 – 14.010 MHz and shall not exceed the general radiated emission limits in §15.209. According to §15.225, except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency Field Strength Measurement Distance (MHz) (μV/m at meter) (meter) 0.009 – 0.490 2400 / F (kHz) 300 0.490 – 1.705 24000 / F (kHz) 30 1.705 – 30.0 30 30 30 - 88 100** 3 88-216 150** 3 216-960 200** 3 Above 960 500 3 ** Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. Page 15

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP Test Configuration 9kHz ~ 30MHz 3m Loop antenna EUT Spectrum / Receiver Turntable 1m 0.8m Reference ground plane 30MHz ~ 1GHz Antenna tower 3m Bilog antenna EUT 4m Spectrum / Receiver Turntable 1m 0.8m Pre-amp Reference ground plane Page 16

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP TEST PROCEDURE For 9kHz ~ 30MHz 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, The center of the loop shall be 1 m above the ground then to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. Set the spectrum analyzer in the following setting as: RBW=10kHz / VBW=30kHz / Sweep=AUTO 6. Repeat above procedures until the measurements for all frequencies are complete. For 30MHz ~ 1GHz 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as: RBW=100kHz / VBW=300kHz / Sweep=AUTO 7. Repeat above procedures until the measurements for all frequencies are complete. Page 17

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP Operation Mode: TX mode Test Date: April 22, 2014 Temperature: 27°C Tested by: David Shu Humidity: 53 % RH Polarity: Ver. / Hor. Correction Detector Frequency Reading Result Limit 3m Margin Factor Mode (MHz) (dBuV) (dBuV/m) (dBuV/m) (dB) (dB/m) (PK/QP/AVG 13.5602 24.2 14.66 38.86 124.00 -85.14 PK Remark: 1. Measuring frequencies from 9kHz to the 1GHz. 2. Radiated emissions measured were made with an instrument using peak/quasi-peak/average detector mode. 3. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 4. Margin (dB) = Result (dBuV/m) – Limit (dBuV/m). Page 18

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 9kHz ~ 30MHz Operation Mode: TX mode Test Date: April 22, 2014 Temperature: 27°C Tested by: David Shu Humidity: 53 % RH Frequency Reading Correction Factor Result Limit Margin Detector Mode (MHz) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dB) (PK/QP/AVG) 2.7033 24.27 13.72 37.99 69.50 -31.51 Peak 7.5429 17.26 14.60 31.86 69.50 -37.64 Peak 13.5629 23.28 14.66 37.94 69.50 -31.56 Peak 21.4126 18.23 14.26 32.49 69.50 -37.01 Peak Remark: 1. Measuring frequencies from 9kHz to the 1GHz. 2. Radiated emissions measured were made with an instrument using peak/quasi-peak/average detector mode. 3. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 4. Margin (dB) = Result (dBuV/m) – Limit (dBuV/m). Page 19

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 30MHz ~ 1GHz Operation Mode: TX mode Test Date: April 23, 2014 Temperature: 27°C Tested by: David Shu Humidity: 53 % RH Correction Frequency Reading Result Limit 3m Margin Ant.Pol. Detector Mode Factor (MHz) (dBuV) (dBuV/m) (dBuV/m) (dB) (H/V) (PK/QP/AVG) (dB/m) 58.1300 45.70 -23.75 21.95 40.00 -18.05 V Peak 153.1900 35.42 -18.07 17.35 43.50 -26.15 V Peak 280.2600 34.63 -16.76 17.87 46.00 -28.13 V Peak 447.1000 35.84 -12.74 23.10 46.00 -22.90 V Peak 504.3300 34.57 -11.76 22.81 46.00 -23.19 V Peak 782.7200 29.36 -7.55 21.81 46.00 -24.19 V Peak 58.1300 55.01 -23.75 31.26 40.00 -8.74 H Peak 70.7400 47.05 -22.59 24.46 40.00 -15.54 H Peak 120.2100 35.31 -17.37 17.94 43.50 -25.56 H Peak 252.1300 44.58 -18.25 26.33 46.00 -19.67 H Peak 322.9400 41.92 -15.85 26.07 46.00 -19.93 H Peak 421.8800 31.82 -13.42 18.40 46.00 -27.60 H Peak Remark: 1. Measuring frequencies from 9kHz to the 1GHz. 2. Radiated emissions measured were made with an instrument using peak/quasi-peak/average detector mode. 3. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 4. Margin (dB) = Result (dBuV/m) – Limit (dBuV/m). Page 20

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 7.3 FREQUENCY STABILITY LIMIT According to §15.225(e), the frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating frequency over a temperature variation of –20 degrees to +50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees C. For battery operated equipment, the equipment tests shall be performed using a new battery. Test Configuration Temperature and Voltage Measurement (under normal and extreme test conditions) Temperature Chamber Spectrum Analyzer EUT AC/DC Power supply TEST PROCEDURE 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the environment into appropriate environment. 4. Set the spectrum analyzer as RBW=1kHz, VBW = RBW, Span = 200kHz, Sweep = auto. 5. Mark the peak frequency and measure the frequency tolerance using frequency counter function. 6. Repeat until all the results are investigated. Page 21

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP TEST RESULTS No non-compliance noted. Temperature Variations Measured Delta Temp. Voltage Tolerance Limit Margin Result Frequency Frequency (oC) (V) (%) (±%) (%) (Pass/Fail) (MHz) (Hz) -20 13.56085 850 0.00627 0.01 -0.00373 Pass -10 13.56094 940 0.00693 0.01 -0.00307 Pass 0 13.56087 870 0.00642 0.01 -0.00358 Pass 10 13.56092 920 0.00678 0.01 -0.00322 Pass 120 20 13.56047 470 0.00347 0.01 -0.00653 Pass 30 13.56088 880 0.00649 0.01 -0.00351 Pass 40 13.56038 380 0.00280 0.01 -0.00720 Pass 50 13.56012 120 0.00088 0.01 -0.00912 Pass Voltage Variations Measured Delta Temp. Voltage Tolerance Limit Margin Result Frequency Frequency (oC) (V) (%) (±%) (%) (Pass/Fail) (MHz) (Hz) 102 13.56058 580 0.00428 0.01 -0.00572 Pass 20 120 13.56096 960 0.00708 0.01 -0.00292 Pass 138 13.56074 740 0.00546 0.01 -0.00454 Pass Page 22

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP 7.4 POWERLINE CONDUCTED EMISSIONS LIMIT According to §15.207(a), except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 µH/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Limits Frequency Range (dBμV) (MHz) Quasi-peak Average 0.15 to 0.50 66 to 56* 56 to 46* 0.50 to 5 56 46 5 to 30 60 50 * Decreases with the logarithm of the frequency. TEST PROCEDURE 1. The EUT was placed on a table, which is 0.8m above ground plane. 2. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 3. Repeat above procedures until all frequency measured were complete. Page 23

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP TEST RESULTS The initial step in collecting conducted data is a spectrum analyzer peak scan of the measurement range. Significant peaks are then marked as shown on the following data page, and these signals are then quasi-peaked. Operation Mode: Normal Link Test Date: April 24, 2014 Temperature: 26°C Tested by: Sehni Hu Humidity: 60% RH QP AV Corr. QP AV QP AV QP AV Freq. Reading Reading factor Result Result Limit Limit Margin Margin Note (MHz) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB) 0.1500 56.03 43.73 0.19 56.22 43.92 66.00 56.00 -9.78 -12.08 L1 0.1860 41.73 22.68 0.19 41.92 22.87 64.21 54.21 -22.29 -31.34 L1 0.2020 48.55 38.03 0.19 48.74 38.22 63.53 53.53 -14.79 -15.31 L1 0.2300 33.10 19.99 0.19 33.29 20.18 62.45 52.45 -29.16 -32.27 L1 0.2540 41.82 28.31 0.19 42.01 28.50 61.63 51.63 -19.62 -23.13 L1 0.4060 33.72 29.01 0.20 33.92 29.21 57.73 47.73 -23.81 -18.52 L1 0.1700 49.14 38.05 0.19 49.33 38.24 64.96 54.96 -15.63 -16.72 L2 0.2020 46.54 30.02 0.19 46.73 30.21 63.53 53.53 -16.80 -23.32 L2 0.2180 42.27 33.05 0.19 42.46 33.24 62.89 52.89 -20.43 -19.65 L2 0.2500 35.42 27.91 0.19 35.61 28.10 61.76 51.76 -26.15 -23.66 L2 0.2740 34.57 26.65 0.19 34.76 26.84 61.00 51.00 -26.24 -24.16 L2 0.4180 28.72 22.27 0.19 28.91 22.46 57.49 47.49 -28.58 -25.03 L2 Remark: 1. The measuring frequencies range between 0.15 MHz and 30 MHz. 2. The emissions measured in the frequency range between 0.15 MHz and 30MHz were made with an instrument using Quasi-peak detector and Average detector. 3. The IF bandwidth of SPA between 0.15MHz and 30MHz was 10kHz. The IF bandwidth of Test Receiver between 0.15MHz and 30MHz was 9kHz. 4. L1 = Line One (Live Line) / L2 = Line Two (Neutral Line) 5. "-" means Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. Page 24

Compliance Certification Services Inc. FCC ID: E2K-DWRFID1401 Report No.: T140414W03-RP Test Plots Conducted emissions (Line 1) Conducted emissions (Line 2) Page 25


Document Created: 2014-06-27 14:44:20
Document Modified: 2014-06-27 14:44:20
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC