User Manual

FCC ID: DWNKEY

Users Manual

Download: PDF
FCCID_2727917

w w w.so m fy.com EN Safety and liability Before installing and using this product, please read this guide carefully. This Somfy product must be installed by a home motorisation and automation professional, for whom this guide is intended. Moreover, the installer must comply with standards and legislation in the country in which the product is being installed, and inform his customers of the operating and maintenance conditions for the product. Any use outside the sphere of application defined by Somfy is prohibited. In this event, as with all usage not consistent with these instructions, Somfy accepts no liability and the Somfy warranty is invalidated. KEYTIS INTERIOR Before beginning installation, check that this product is compatible with the associated equipment and accessories. Safety instructions EN Instructions  Keep the Keytis interior out of the reach of children. Never drop, knock drill or submerge the Keytis interior.  Do not use abrasive products or solvents to clean the product.  Ref. 5124979A Ensure batteries are separated from other types of waste and are recycled via your local recycling centre. FCC STATEMENTS This portable transmitter with its antenna complies with FCC/IC RF exposure Somfy SAS limits for general population / uncontrolled exposure. 50 avenue du Nouveau Compliance Statement (Part 15.19) Monde This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: F-74300 CLUSES 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Warning (Part 15.21) www.somfy.com Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Interference Statement (Part 15.105 (b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee Somfy SAS, capital 20.000.000 Euros, that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct RCS Annecy 303.970.230 -09/2014 the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. EN Safety and liability Before installing and using this product, please read this guide carefully. EN Safety and liability Before installing and using this product, please read this guide carefully. This Somfy product must be installed by a home motorisation and automation professional, for This Somfy product must be installed by a home motorisation and automation professional, for whom this guide is intended. Moreover, the installer must comply with standards and legislation in whom this guide is intended. Moreover, the installer must comply with standards and legislation in the country in which the product is being installed, and inform his customers of the operating and the country in which the product is being installed, and inform his customers of the operating and maintenance conditions for the product. maintenance conditions for the product. Any use outside the sphere of application defined by Somfy is prohibited. In this event, as with all Any use outside the sphere of application defined by Somfy is prohibited. In this event, as with all usage not consistent with these instructions, Somfy accepts no liability and the Somfy warranty is usage not consistent with these instructions, Somfy accepts no liability and the Somfy warranty is invalidated. invalidated. Before beginning installation, check that this product is compatible with the associated equipment Before beginning installation, check that this product is compatible with the associated equipment and accessories. and accessories. Safety instructions Safety instructions  Never drop, knock drill or submerge the Keytis interior. Keep the Keytis interior out of the reach of children.  Keep the Keytis interior out of the reach of children. Never drop, knock drill or submerge the Keytis interior.  Do not use abrasive products or solvents to clean the product.  Do not use abrasive products or solvents to clean the product.   Ensure batteries are separated from other types of waste and are recycled via your local recycling Ensure batteries are separated from other types of waste and are recycled via your local recycling centre. centre. FCC STATEMENTS FCC STATEMENTS This portable transmitter with its antenna complies with FCC/IC RF exposure This portable transmitter with its antenna complies with FCC/IC RF exposure limits for general population / uncontrolled exposure. limits for general population / uncontrolled exposure. Compliance Statement (Part 15.19) Compliance Statement (Part 15.19) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 2. This device must accept any interference received, including interference that may cause undesired operation. Warning (Part 15.21) Warning (Part 15.21) Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. to operate the equipment. FCC Interference Statement (Part 15.105 (b) FCC Interference Statement (Part 15.105 (b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. - Consult the dealer or an experienced radio/TV technician for help.

EN 1) Programming the control point 1 1 Remove the clip (fig1) Use a screwdriver to make a short contact (less than 2s) on the “prog band” (fig 2) located at the back of remote control. The motorised product moves up and down. The control point is programmed in the motor. 2) Use Press the Up button to move the motorised product to the up end limit and the Down button to stop the motorised product before it reach the up end limit. Press the Down button to move the motorised product to the down end limit and the Up button to stop the motorised product before it reach the down end limit. 2 3) Battery replacement: To change the battery, see pictures 1 to 8. 4) Technical data Frequency bands and maximum power used: 433,42 MHz e.r.p < 63 µW Operating temperature: -20°C to + 60°C Power supply: 1 x 3V battery type CR 2032 Protection rating IP 40 2 EN 1) Programming the control point Remove the clip (fig1) Use a screwdriver to make a short contact (less than 2s) on the “prog band” (fig 2) located at the back of remote control. The motorised product moves up and down. The control point is programmed in the motor. 2) Use Press the Up button to move the motorised product to the up end limit and the Down button to stop the motorised product before it reach the up end limit. Press the Down button to move the motorised product to the down end limit and the Up button to stop the motorised product before it reach the down end limit. 3) Battery replacement: To change the battery, see pictures 1 to 8. 4) Technical data Frequency bands and maximum power used: 433,42 MHz e.r.p < 63 µW Operating temperature: -20°C to + 60°C Power supply: 1 x 3V battery type CR 2032 3 2 3 Protection rating IP 40 1 EN 1) Programming the control point Remove the clip (fig1) Use a screwdriver to make a short contact (less than 2s) on the “prog band” (fig 2) located at the back of remote control. The motorised product moves up and down. The control point is programmed in the motor. 4 5 6 2) Use Press the Up button to move the motorised product to the up end limit and the Down button to stop the motorised product before it reach the up end limit. Press the Down button to move the motorised product to the down end limit and the Up button to stop the motorised product before it reach the down end limit. 3V 3V CR 2032 CR 2032 + 3V + CR 203 2 + 3) Battery replacement: To change the battery, see pictures 1 to 8. 4) Technical data 7 8 Frequency bands and maximum power used: 433,42 MHz e.r.p < 63 µW Operating temperature: -20°C to + 60°C Power supply: 1 x 3V battery type CR 2032 Protection rating IP 40


Document Created: 2015-07-24 11:34:54
Document Modified: 2015-07-24 11:34:54
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC