6 CONFIDENTIAL SHORT TERM HPA-MYT-TX User manual 1 of 2

FCC ID: CWU-MYTTX

Users Manual

Download: PDF
FCCID_2990974

QUICK START GUIDE HPA-MYT-TX/RX MyTurn TM Source Selector Overview MyTurn Source Selector Solution in a Conference Room The HPA-MYT-TX MyTurn™ Source Selector Button (FG554-21) connects to the end of The eight outputs on the rear of the MyTurn Source Selector Receiver connect using a standalone MyTurn-Ready cable (HDMI, Mini-DP, DP, RGB, USB), or one thats installed Phoenix connector to the SW inputs on Solecis SDX-510M-DX, or GPIO inputs on NI in a Retractable Cable Module (RCM). A user presses the button to send their device Controllers or Enova DVX devices. When the MyTurn Source Selector Button paired with content to a conference room display. When pressed, the button wirelessly transmits a that I/O port is triggered, the MyTurn Source Selector Receiver activates the AMX signal to the HPA-MYT-RX MyTurn Source Selector Wireless Receiver (FG554-23) that is device “SW” input or I/O port, signaling the system to switch the display to that port. wired to an AMX master controller or an AMX switching device, such as a Solecis SDX or Enova DVX. When used with a Solecis SDX, simple switching can be implemented with MyTurn Button no NetLinx programming required. Each MyTurn Source Selector Receiver can accommodate up to 8 MyTurn Source Selector Buttons. MyTurn Receiver Pairing and port select button MyTurn TX Button mDP HDMI DP HydraPort Chassis MyTurn-Ready Cables in a HydraPort RCM FIG. 1 HPA-MYT-TX MYTURN BUTTON (LEFT) AND HPX-MYT-RX MYTURN RECEIVER (RIGHT) MyTurn Source Selector Buttons and Receivers have the following user features: Solecis SDX MyTurn Source Selector Button • Push button – activates input at switcher to display device content FIG. 2 MYTURN TO AMX SOLECIS DIGITAL SWITCHER CONNECTION EXAMPLE MyTurn Receiver • Select Button – press momentarily to switch ports (indicated by LEDs) Following are examples of two typical MyTurn Source Selector installations. – press and hold to enter “pairing” mode Solecis SDX-410/510/810 Switchers – press and hold during power up to reset to factory defaults The MyTurn Source Selector Receiver connects to the AMX Solecis front AXLINK port for power and ground as outlined in FIG. 3. Output ports (1 through 8) are wired to the Product Specifications . corresponding Solecis rear “SW” input that has a MyTurn Source Selector Button HPA-MYT-TX SPECIF ICATIONS equipped cable connected to it. This solution can be implemented without NetLinx programming since the SW port is directly connected to the Receiver. Dimensions • 1.421” x .645” x 0.40” HWD (36mm x 16mm x 10mm) HPX-MYT-RX Receiver Solecis SDX-Front Solecis SDX-Rear Power: • Integrated 3VDC coin-cell battery (not replaceable) Environment • Operating Temperature: 32° F (0° C) to 122° F (50° C) • Operating Humidity: 20% to 85% RH Top Panel: • Push-button Power LED Compatibility: Flat Cable Assemblies: • FG10-2192-xx - HDMI 4K60 MyTurn-Ready Flat Cable (xx=16 or 32 ft) • FG10-2193-16 - DisplayPort 4K60 MyTurn-Ready Flat Cable • FG10-2195-16 - RGB with Auto MyTurn-Ready Flat Cable MyTurn-Ready • FG10-2196-16 - Mini DisplayPort 4K60 MyTurn-Ready Flat Cable HPX-MYT-TX HDMI Cable Button Display End • FG10-2197-16 - USB MyTurn-Ready Flat Cable Retractable Cable Module (RCM) Assemblies: • FG552-32 - HDMI 4K60 RCM with MyTurn-Ready Cable • FG552-33 - DisplayPort 4K60 RCM with MyTurn-Ready Cable MyTurn-Ready HDMI Cable • FG552-36 - Mini DisplayPort 4K60 RCM with MyTurn-Ready Cable Source End • FG552-35 - RGB with Stereo RCM with MyTurn-Ready Cable • FG552-37 - USB 3.0 RCM with MyTurn-Ready Cable FIG. 3 MYTURN SOURCE SELECTOR SW CONNECTION (1 CONNECTION SHOWN) Accessories: • HPX-2BTN-8ACC - 8 button inserts and 8 cable bands kit (optional) Note: Only on the 5x1 TX, set dipswitch #4 in the ON position (Direct Mode). This will set • Installation Guide Included the external button behavior to be in direct mode by default. Once the dipswitch is turned ON the 5x1 TX must be rebooted in order for the setting to take effect. HPA-MYT-RX SPECIF ICATIONS Enova DVX Master/NetLinx Integrated Controller Dimensions (HWD) • 3.21” x 2.54” x 0.55” HWD (82.55mm x 69.85mm x 15.24mm) The MyTurn Source Selector Receiver connects to an AMX DVX Master or a NetLinx Controller using the GPIO interface as outlined in FIG. 4. The GPIO port can deliver Enclosure: • Polycarbonate plastic with matte finish Power and Ground as well as receive switch inputs 1-8. Input Voltage: • 8-15 VDC on the “+12V” input operates LEDs and I/O outputs This solution requires NetLinx programming to correlate a GPIO input button event to to Solecis, NI-Controller or DVX Switcher switch to a predetermined port on the DVX. Environment • Operating Temperature: 0° C (32° F) to 50° C (122° F) HDMI Cable with • Operating Humidity: 20% to 85% RH HPA-MYT-TX MyTurn Button Front Panel: • 8 Yellow LEDs • 1 Push button for pairing or port selection Rear Panel: • 1 x 6 Phoenix screw-terminal - I/O 1-4 and Power/Ground • 1 x 4 Phoenix screw-terminal - I/O 5-8 • 1 Green LED indicates power is applied, and flickers when any wireless transmission is detected. HPA-MYT-RX MyTurn Receiver Accessories: • Quick Start Guide Included DVX Master FIG. 4 MYTURN SOURCE SELECTOR DVX GPIO TERMINATIONS (5 CONNECTIONS SHOWN)

Installation MyTurn Pairing Refer to the following steps to install the MyTurn Source Select Buttons and Receivers. Perform the following steps to pair each MyTurn Source Selector Button with each port on the MyTurn Source Selector Receiver. MyTurn Source Selector Receiver Caution: A receiver will hear every MyTurn Source Select Button within its proximity Note: The MyTurn Source Selector Wireless Receiver must be installed within 10 meters (receivers in adjoining conference rooms will likely see each other's TX's but will ignore (32 ft) of the MyTurn Source Selector Buttons. Care must be taken to minimize any that it is not paired with.) It is the responsibility of the installer to only put one metal obstructions to the wireless signal (i.e., equipment racks). receiver at a time into pairing mode to avoid inadvertent behavior. 1. Remove the Phoenix connector from the back of the receiver and wire the outputs 1. Press and hold the Select button on the front of the MyTurn Source Selector to the Solecis, DVX, or NX/NI Master Controller using the screw down terminals. Receiver for approximately 3 seconds. The yellow port LEDs will all flash and Port Ensure Power and Ground are connected as shown (FIG. 5). Use the AXLINK ports 1 will blink awaiting the wireless MyTurn Source Selector Button press to pair. for Power and Ground if connecting to a Solecis as described in FIG. 3. Select Button - press momentarily to switch ports - press and hold 3 sec to start pairing - press and hold 3 sec during power up to reset to factory default FIG. 8 MYTURN SOURCE SELECTOR WIRELESS RECEIVER - SELECT BUTTON 2. Press the MyTurn Source Select Button to pair it with the blinking port or press Select to select another port to pair with. Upon successful pairing, the selected LED will turn on solid for one second, and then the LED flashing will advance to the FIG. 5 PHOENIX CONNECTOR WIRING (DVX/NI-CONTROLLER GPIO TO MYTURN RECEIVER) next output to indicate the device is still in pairing mode. The receiver will pair the first transmitter it hears when pairing a particular output. Note: When connecting each output (1-8), note the device type, input port, location (ex. HydraPort Pos-1) on the worksheet below-right for recording this data. It may be needed 3. Repeat the MyTurn Source Select Button installation and pairing procedure for when pairing the MyTurn Source Selector Buttons with the wireless receiver ports. each button required. To exit the pairing mode, press the Select button for 3 seconds again. All front yellow LEDs will flash 3 times and then the first output Refer to the wiring chart below for the appropriate wire gauge. will be selected. Pairing mode will exit after 2 minutes of no action. WIRING GUIDELINES Note: Successive momentary presses of the front panel button on the receiver will Wire Size Maximum wiring length Wire Size Maximum wiring length keep the unit in pairing mode, resetting the pairing timeout counter, and advance the slot assignment to the next output in a round-robin fashion. 18 AWG 154.83 feet (47.19 meters) 22 AWG 63.40 feet(19.32 meters) 4. If the unit has exited pairing mode before all ports are paired, press and hold the 20 AWG 98.30 feet(29.96 meters) 24 AWG 38.68 feet (11.79 meters) Select button for 3 seconds again to enter the pairing mode and momentarily press the button multiple times to advance the pairing to restart where the last 2. Connect the +12V and Ground wire ends to the MyTurn Source Selector Receiver port was set. A new pairing will overwrite the prior pairing. and GPIO or AxLink plugs first to ensure proper connection. 5. Secure the device under the table once all cabling and pairing is complete. 3. Connect the remaining outputs to the plugs on both ends. 4. Insert the plugs at the Receiver and then the GPIO or AxLink sockets. The green Return to Factory Default LED on the rear of the Receiver will light when power is applied. To return a receiver to the factory default settings, perform the following steps: MyTurn Source Selector Button Note: Returning to factory defaults will wipe any pairing data from the system memory. The MyTurn Source Selector Button can be installed onto the end of any MyTurn-Ready 1. Hold the SELECT button and apply power. Continue holding the SELECT button for cable (FIG. 6). It is then wirelessly paired to the MyTurn Source Selector Receiver. another 3 seconds. All receiver output status LEDs will simultaneously flash three times on startup (after being returned to factory settings). HDMI mDP Operation RGB+Stereo To operate the MyTurn Source Selector Button after installation is complete, just connect the cable source end to the presenting device and momentarily push the DP MyTurn Source Selector Button. The LED on the button will momentarily flash green. USB Type A The device content is now viewable on the main display. Installation Worksheet MYTURN RECEIVER DEVICE INPUT Port Wired to Device Type/Name Port Pair to Cable Type/Location 1 FIG. 6 MYTURN-READY SOURCE SELECTOR BUTTONS SHOWN MOUNTED ON VARIOUS CABLES 2 1. At the source end of the cable, clip the MyTurn Source Selector Button onto the MyTurn-Ready connector over-mold with the LED over the connector end (FIG. 7). 3 4 MyTurn Button clips into source cable channel 5 6 7 Channel in MyTurn-Ready cable over-mold 8 Additional Documentation Clip installs under cable and latches Refer to the catalog page on www.amx.com (Dealer Site) for additional product over the MyTurn Button documentation. FIG. 7 MYTURN-READY SOURCE SELECTOR BUTTON CLIPPING ONTO CABLE END 2. There are short and tall securing clips. The Tall clip is used on the RGB+Stereo MyTurn-Ready cable due to the bulk of the over-mold. Press the clip into the MyTurn-Ready cable channel until it clicks over the MyTurn-Ready button. 3. Pair each MyTurn Source Select Button as it is installed. Refer to the install worksheet filled out during the MyTurn Source Selector Receiver installation. © 2016 Harman. All rights reserved. Hydraport, AMX, AV FOR AN IT WORLD, HARMAN, and their respective logos are registered trademarks of 93-0554-21 REV: A HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective companies. AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time. The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com. 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153 Last Revised: 3/15/2016 AMX (UK) LTD, AMX by HARMAN - Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/


Document Created: 2016-04-01 12:12:44
Document Modified: 2016-04-01 12:12:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC