User Manual

FCC ID: COF-UNA-A

Users Manual

Download: PDF
FCCID_2619090

Doc. Title UNA -A EVB User Manual Originator Max Date 2015/03/20 Version V14 1/16 Rev 1.1

Revision Record Version Revise content Date 1.1 New release 2014-10-03 1.2 EVB V12 2014-12-27 1.3 EVB V13 2015-03-02 1.4 Add FCC/IC/CE warning statement include 2015-03-20 2/16 Rev 1.1

UNA-A EVB User Guide 1. Illustration of Function EVB J2 J4 J6 J5 U2 Top View J1 J3 Bottom View 3/16 Rev 1.1

Component Function Description reference J1 Test Conn. MP test connector. Connect host PC or download firmware.(Micro USB). J2 USB Conn. note1. J3 SMA Conn. Connect to external Antenna J4 Test Conn. Debug connector. J5 Power supply IN Optional Connect to external Power supply input. J6 GND System GND. U2 SIM Conn. SIM card slot. Note1: USB port , doesn't provide the power input. 2. Configure the UNA-A EVB J15 Top View Download Key : Component reference Function J15 Enable Download mode. Note: To enable download mode, Please close J15 and refer to “MTK_flashtool_UserGuide” 4/16 Rev 1.1

3. General action Step1. Insert SIM card. Step2. Set up Antenna. 5/16 Rev 1.1

Step3. Connect computer by USB cable. Step4. Set up Power In. a. J5 is power input, and voltage range is from 3.4 to 4.35V. b. J6 is GND. 6/16 Rev 1.1

Computer Power supply.(3.4V~4.35V) USB Cable - + Diagram of Application 4. Settings for Download Mode Component reference Open/Short Function Open Close Download mode J15 Short Start Download mode 7/16 Rev 1.1

Step1. Put back the jumper,J15.( Two kinds of selection) Step2. Connect EVB and computer by USB cable. Step3. Set up Power In. a. J1 is power input, and voltage range is from 3.4 to 4.35V. b. J2 is GND. 8/16 Rev 1.1

EVB test point pin define J1 Pin define(Bottom view) 49 1 50 2 Pin number Pin name Pin number Pin name 1 VBAT 2 RESERVE 3 VBAT 4 RESERVE 5 VBAT 6 RESERVE 7 GND 8 GND 9 GND 10 GND 11 NC 12 NC 13 NC 14 NC 15 GND 16 GND 17 GPI_2 18 NC 19 NC 20 GPI_1 21 U1RXD 22 U1TXD 23 U1RTS 24 U1CTS 25 FW_READY 26 WAKEUP_AP 27 RESERVE 28 SAR_DET 29 NC 30 NC 31 U0TXD 32 U0RXD 33 NC 34 NC 35 NC 36 NC 37 NC 38 NC 39 DL KEY 40 EINT0 41 NC 42 VDD_UART 43 NC 44 NC 45 NC 46 NC 47 NC 48 NC 49 NC 50 NC 9/16 Rev 1.1

FCC Regulations This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and the maximum antenna gain allowed for use with this device is 3dBi. 10/16 Rev 1.1

2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: COF-UNA-A”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Industry Canada(IC) statement: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions 11/16 Rev 1.1

suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement." Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé. IMPORTANT NOTE: 12/16 Rev 1.1

In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 10293A-UNAA”. Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 10293A-UNAA". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de 13/16 Rev 1.1

l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel. CE (European Union Notice) Česky [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se [Czech] základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets [Danish] typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in [German] Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme [Estonian] tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español Por medio de la presente [nombre del fabricante] declara que el [clase de [Spanish] equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ∆ΗΛΩΝΕΙ ΟΤΙ [type of equipment] [Greek] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ. Français Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est [French] conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] [Italian] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of [Latvian] equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. 14/16 Rev 1.1

Lietuvių Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius [Lithuanian] reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlan Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in ds [Dutch] overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma [Maltese] mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó [Hungarian] alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z [Polish] zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Portuguê [Nome do fabricante] declara que este [tipo de equipamento] está conforme com s os requisitos essenciais e outras disposições da Directiva 1999/5/CE. [Portuguese ] Slovensk [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in o ostalimi relevantnimi določili direktive 1999/5/ES. [Slovenian] Slovensk [Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a y [Slovak] všetky príslušné ustanovenia Smernice 1999/5/ES. Suomi [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen [Finnish] tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med [Swedish] de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. This device complies with the R&TTE Directive (1999/5/EC) issued by the Commission of the European Community. A minimum separation distance of 20 cm must be maintained between the user’s body and the device, including the antenna during body-worn operation to comply with the RF exposure requirements in Europe. R&TTE Regulation: 15/16 Rev 1.1

In all cases assessment of the final product must be mass against the Essential requirements of the R&TTE Directive Articles 3.1(a) and (b), safety and EMC respectively, as well as any relevant Article 3.3 requirements. The maximum antenna gain for frequency 900 is 3 dBi; for frequency 1800 is 3 dBi and the antenna separation distance is 20cm. 2200 16/16 Rev 1.1


Document Created: 2015-05-15 11:07:15
Document Modified: 2015-05-15 11:07:15
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC