SAR Report Appendix 1

FCC ID: CNFSPJB1

RF Exposure Info

Download: PDF
FCCID_4328824

Appendix C – Dipole Calibration Certificates 2.4GHz Dipole

Calibration Laboratory of Kw Schmid & Partner // G Schweizerischer Kalibrierdienst g Service suisse d‘étatonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 48, 8004 Zurich, Switzerland S Swiss Calibration Service Aceredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certficates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear(frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Condiitions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. «_ SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D2450V2—1005_Nov17 Page 2 of 8

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 54.10+1.6 0 Retum Loss +275 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 51.2 0+ 3.5 jn Retum Loss —28.7 dB General Antenna Parameters and Design | Electrical Detay (anedirection) | 1.157 ns ] After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard seririgid coaxial cable. The center conductorof the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions* paragraph. The SAR data are not affected by this change. The overall dipols length is stil according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on December 29, 2016 Certiicate No: D2450V2—1005_Nov17 Page 4 of 8

UASY5 Validation Heport tor Head TSL Date: 07.11.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN:1005 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 1.86 S/m; s = 37.8; p = 1000 kg/mJ Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: + Probe: EX3DV4 — SN7349; ConvF(8.12, 8.12, 8.12); Calibrated: 31.05.2017; + Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 Sn601; Calibrated: 26.10.2017 * Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 «_ DASY32 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurementgrid: dx=5mm, dy=5mm, dz=5mm Reference Value = 114.6 V/m; Power Drift =—0.03 dB Peak SAR (extrapolated) =27.1 W/kg SAR(I g) = 13.4 W/kg; SAR(10 g) = 6.19 W/kg Maximum value of SAR (measured) = 22.0 W/kg —4.00 —8.00 —12.00 —16.00 —20.00 0 dB =22.0 W/kg = 13.42 dB W/kg Certificate No: D2450V2—1005_Novi7 Page 5 of 8

Impedance Measurement Plot for Head TSL 7 Nev 2017 14:00:12 sit a uo rs 1: 54.096 o 1.5625 n 101.50 pH 2 450,000 000 MHz eT § es Del — A Cs [ 1 T | » A~ *q Av L 4 16° *z Hid s cn2 Ca Ay 16° H1d START 2 250.000 000 M4z SToP 2 650.000 000 MHz Certificate No: D2450V2—1005_Nov17 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 07.11.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN:1005 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: £= 2450 MHz; 0 = 2.02 S/m; s = 51.5; p = 1000 kg/m“ Phantom section: Flat Section Measurement Standard: DASY3 (IEEE/IEC/ANSI C63.19—2011) DASY32 Configuration: * Probe: EX3DV4 — SN7349; ConvF(8.1, 8.1, 8.1); Calibrated: 31.05.2017; *« Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 26.10.2017 «+ Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 «_ DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurementgrid: dx=5mm, dy=5mm, dz=5mm Reference Value = 106.8 V/m; Power Drift =—0.05 dB Peak SAR (extrapolated) = 25.6 W/kg SAR(I g) = 12.8 W/kg:; SAR(10 g) = 6 W/kg Maximum value of SAR (measured)= 20.7 W/kg —4.00 —8.00 —12.00 16.00 —20.00 0 dB = 20.7 W/kg = 13.16 dBW/kg Certificate No: D2450V2—1005_Nov17 Page 7 of 8

Impedance Measurement Plot for Body TSL 7 Nev 2017 13:57:57 CB3 si i U Fs 11 51.209 a 25098 227.99 pH 2 450,000 000 MHz Del Ca [ 4 B 159 HLd cH2 by 16° Hid STaRT 2 250.000 000 hiz SToP 2 650.000 000 MHz Certificate No: D2450V2—1005_Nov17 Page 8 of 8

Calibration Laboratory of lt L w _ Schweizerischer Kalibrierdienst P Schmid & Partner J w g Service suisse d‘étalonnage Engineering AG s Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ¥, Tltals® s S swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Ctient BACL Certificate No: D5GHzV2—1001_Sep17 CALIBRATION CERTIFICATE Object D5GHzV2 — SN: 1001 Calibration procedure(s) QA CAL—22.v2 Calibration procedure for dipole validation kits between 3—6 GHz Calibration date: September 18, 2017 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probabilty are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facilty: environmenttemperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards 1D # Cal Date (Cortificate No.) Scheduled Calibration Power meter NRP SN: 104778 Od—Apr—17 (No. 217—02521/02522) Apr—18 Power sensor NRP—291 SN: 108244 O4—Apr—17 (No. 217—02521) Apr—18 Power sensor NRP—291 SN: 103245 Od—Apr—17 (No. 217—02522) Apr—18 Reference 20 dB Attenuator SN: 5058 (204) 07—Apr—17 (No. 217—02528) Apr—18 Type—N mismatch combination SN: 5047.2 / o6g27 07—Apr—17 (No. 217—02529) Apr—18 Reference Probe EXGDV4 SN: 3503 31—Dec—16 (No. EX3—3503_Dect6) Dec—17 DAE4 SN: 601 28—Mar—17 (No. DAE4—601_Mar17) Mar18 Secondary Standards tb # Check Date (in house) Scheduled Check Power meter EPM~442A SN: GB37480704 07—Oct—15 (in house check Oct—16) in house check: Oct—18 Power sensor HP 8481A SN: US37292783 07—Oct—15 (in house check Oct—16) in house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) in house check: Oct—18 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Oct—16) in house check: Oct—18 Network Analyzar HP 8763E SN: US37300585 18—0ct—01 (in housecheck Oct—16) in house check: Oct—17 Name Function Signature Calibrated by: Jeton Kastrati Laboratory Technician o*/ NKA Approved by: Katja Pokovie Technical Manager Issued: September 19, 2017 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D5GHzV2—1001_Sep17 Page 1 of 13

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner S Service suissed‘étalonnage Engineering AG i ns C Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland "/,,/r_\\\ y S Swiss Calibration Service Zalitabet® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM xy,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. * SAR measured: SAR measured at the stated antenna input power. * SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. «_ SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D5GHzV2—1001_Sep17 Page 2 of 13


Head TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mhoim Measured Head TSL parameters (22.0 £0.2) °C 36.2 2 6 % 4.95 mho/m + 6 % Head TSL temperature change during test <0.5 °C ——~— SAR result with Head TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.13 Wikg SAR for nominal Head TSL parameters normalized to 1W 81.5 W / kg x 19.9 % (k=2) SAR averaged over 10 om‘ (10 g) of Head TSL condition SAR measured 100 mW input power 2.32 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.3 W/kg £19.5 % (k=2) Head TSL parameters at 5750 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.4 5.22 mhoim Measured Head TSL parameters (22.0 £0.2) °C 36.0 £ 6 % 5.12 mho/m # 6 % Head TSL temperature change during test <0.5°C —~ —— SAR result with Head TSL at 5750 MHz SAR averaged over 1 em‘ (1 g) of Head TSL Condition SAR measured 100 mW input power 7.98 Wikg SAR for nominal Head TSL parameters normalized to 1W 80.0 W/kg #19.9 % (k=2) SAR averaged over 10 cm‘ (10 g) of Head TSL condition SAR measured 100 mW input power 2.26 Wikg SAR for nominal Head TSL parameters normalized to 1W 22.7 Wikg #19.5 % (k=2) Certificate No: D5GHzV2—1001_Sep17 Page 4 of 13

Body TSL parameters at 5250 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.36 mho/m Measured Body TSL parameters (22.0 £0.2) °C 47.0 26 % 5.49 mho/m £6 % Body TSL temperature change during test <0.5 °C ~— «> SAR result with Body TSL at 5250 MHz SAR averaged aver 1 om‘ {1 g) of Body TSL Condition SAR measured 100 mW input power 7.63 Wikg SAR for nominal Body TSL parameters normalized to 1W 75.7 Wikg # 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 214 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.2 Wikg # 19.5 % (k=2) Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 £0.2) °C 46.4 x6 % 5.96 mho/m # 6 % Body TSL temperature change during test <0.5 °C —— ———— SAR result with Body TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.96 Wikg SAR for nominal Body TSL parameters normalized to 1W 79.0 Wikg 2 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.24 Wikg SAR for nominal Body TSL parameters normalized to 1W 22.2 Wikg a 19.5 % (k=2) Certificate No: DSGHzV2—1001_Sep17 Page 5 of 13

Body TSL parameters at 5750 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.3 5.94 mho/m Measured Body TSL parameters (22.0 0.2) °C 46.1 £6 % 6.17 mho/m x 6 % Body TSL temperature change during test <0.5 °C —— —~— SAR result with Body TSL at 5750 MHz SAR averaged over 1 em‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 7.64 Wikg SAR for nominal Body TSL parameters rnormalized to 1W 75.8 Wikg #19.9 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 100 mW input power 213 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.1 Wikg £19.5 % (k=2) Certificate No: D5GHzV2—1001_Sep17 Page 6 of 13

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL at 5250 MHz Impedance, transformed to feed point §1.4 0 — 6.7 |Q Retum Loss —23.4 dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 53.9 0 —1.7 j|Q Return Loss —27.7 dB Antenna Parameters with Head TSL at 5750 MHz Impedance, transformed to feed point 55.9 0 +3.1 in Return Loss ~24.1 dB Antenna Parameters with Body TSL at 5250 MHz Impedance, transformed to feed point 51.1 0 —5.4 jQ Return Loss —25.3 dB Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 55.7 0 — 1.9 jQ Retum Loss —24.9 dB Antenna Parameters with Body TSL at 5750 MHz Impedance, transformed to feed point 56.7 0 + 2.3 jQ Retum Loss —23.5 dB General Antenna Parameters and Design Electrical Detay (one direction) 1.202 ns J After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxia! cable. The center conductor of the feeding line is direcily connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On someof the dipoles, small end caps are added to the dipole arms in orderto improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections nearthe feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on April 02, 2003 Certificate No: D5SGHzV2—1001_Sep17 Page 7 of 13

DASY5 Validation Report for Head TSL Date: 15.09.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 5GHz; Type: DSGHzV2; Serial; DSGHzV2 — SN: 1001 Communication System: UID 0 — CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz Medium parameters used: f = 5250 MHz; 0 = 4.59 S/m; s; = 36.7; p = 1000 kg/m* Medium parameters used: £= 5600 MHz; 0 = 4.95 $/m; s; = 36.2; p = 1000 kg/m* Medium parameters used: f= 5750 MHz; 0 = 5.12 S/m; ; = 36.0; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN3503; ConvF(5.58, 5.58, 5.58); Calibrated: 31.12.2016, ConvF(5.09, 5.09, 5.09), Calibrated: 31.12.2016, ConvF(5.02, 5.02, 5.02); Calibrated: 31.12.2016; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAEA4 $n601; Calibrated: 28.03.2017 & Phantom: Flat Phantom 5.0 (front); Type: QDOOOP50AA; Serial: 1001 * DASY52 52.10.0(1446);, SEMCAD X 14.6.10(7417) Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5250 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 67.13 V/m; Power Drift =—0.07 dB Peak SAR (extrapolated) = 28.5 W/kg SAR(1 g) =7.85 W/kg; SAR(10 g) = 2.25 W/kg Maximum value of SAR (measured) = 18.0 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1 4mm Reference Value = 67.01 V/m; Power Drift =—0.03 dB Peak SAR (extrapolated) = 31.5 W/kg SAR(L g) =8.13 W/kg; SAR(10 g) = 2.32 W/kg Maximum value of SAR (measured) = 19.2 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5750 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 65.65 V/m; Power Drift = —0.06 dB Peak SAR (extrapolated) = 31.7 W/kg SAR(I g) = 7.98 W/kg; SAR(10 g) = 2.26 W/kg Maximum value of SAR (measured) = 19.1 W/kg Certificate No: D5GHzV2—1001_Sep17 Page 8 of 13

5.00 —10.00 —15.00 —20.00 25.00 0 dB = 19.1 W/kg= 12.81 dBW/kg Certificate No: DSGHzV2—1001_Sep17 Page 9 of 13

Impedance Measurement Plot for Head TSL 15 Sep 2oi7? idrdo:42 it i U Fs 11519790 —669920 4.9252pF 5 250.000 000 Kz T_ CHL Markers 2 $3,928 a ~4,5835 a 5.60000 GHz 3 55.991 a 2.0762 a 5.75000 GHz hy 16 ® HLd CH2 CH2 Markers Cor %—27.718 08 $.60000 GHz a:—24.050 dB $.75000 GHz Avi 16° H1d STaRT 5 000.000 000 Mz SToP 6 000,000 000 MHz Certificate No: DSGHzV2—1001_Sep17 Page 10 of 13

DASYS5 Validation Report for Body TSL Date: 18.09.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 5GHz; Type: D5SGHzV2; Serial: DSGHzV2 — SN: 1001 Communication System: UID 0 — CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz Medium parameters used: f = 5250 MHz; 0 = 5.49 S/m; s= 47.0; p = 1000 kg/m* Medium parameters used: £= 5600 MHz; 0 = 5.96 $/m; £;= 46.4; p = 1000 kg/m* Medium parameters used: f= 5750 MHz; 0 = 6.17 S/m; &,= 46.1; p = 1000 kg/m’ Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: «_ Probe: EX3DV4 — SN3503; ConvF(5.14, 5.14, 5.14); Calibrated: 31.12.2016, ConvF(4.57, 4.57, 4.57); Calibrated: 31.12.2016, ConvF(4.51, 4.51, 4.51); Calibrated: 31.12.2016; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) «_ Electronics: DAEA4 Sn601; Calibrated: 28.03.2017 + Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 & DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5250 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 59.82 V/m; Power Drift = —0.06 dB Peak SAR (extrapolated) = 29.2 W/kg SAR(L g) = 7.63 W/kg; SAR(1O0 g) = 2.14 W/kg Maximum value of SAR (measured) = 17.3 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 59.65 V/m; Power Drift = —0.07 dB Peak SAR (extrapolated) = 33.1 W/kg SAR(I g) = 7.96 W/kg; SAR(10 g) = 2.24 W/kg Maximum value of SAR (measured) = 18.7 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5750 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 58.36 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 33.1 W/kg SAR(1 g) = 7.64 W/kg; SAR(10 g) =2.13 W/kg Maximum value of SAR (measured) = 18.3 W/kg Certificate No: DSGHzV2—1001_Sep17 Page 23 of 23

—10.00 ~20.00 ~30.00 ~40.00 —50.00 0 dB = 17.3 W/kg = 12.38 dBW/kg Certificate No: D5GHzV2—1001_Sep17 Page 12 of 18

E1 10 51 abeq Lides~Looi—sAzH9sa :on steomeq ZHM 800 600°000 5 4015 zi 008 000°000 5 14w15 PTH 3 zh9 ©0oSz‘S ap ereec—t Tho eo009‘s ab Ob6 be—12 w09 sAe2tH THO THo PTH ar Bau 9 conge‘s 09 €5907— t°o suexen tho es zuL ce cocrest 5 adessors torke vetmte it si n t ts EBJ evsorizt atoz dos st 791 Apog 101 101q juowainseapy eouepaduj


Document Created: 2019-06-22 06:20:02
Document Modified: 2019-06-22 06:20:02
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC