Users Manual

FCC ID: CFS8DLWFZW

Users Manual

Download: PDF
FCCID_3922431

ADTZWM Wi-Fi® and Z-Wave® Module Installation and Setup Guide General Information The Communication Modules allow the control panel to communicate with the Central Station via the cellular radio network. The module connects directly to the control panel and is powered via the control panel’s connection. The ADTZWM communications module is intended to provide compatible ADT control panels with a Wi-Fi connection as well as connection with and the ability to control Z-Wave devices. Compatible Controls: ADT7AIO/ADT5AIO Series - Installation Guide P/N 800-24121 or higher. ADTHYBWL Series - Installation Guide P/N 800-24125 or higher. ADT2X16AIO Series – Installation Guide P/N 800-24341 or higher. Installing the Module in the ADT7AIO/ADT5AIO or ADT2X16AIO Series 1. Affix the provided FCC/IC label (P/N 800- 24286 on the control’s case back (refer to Figure 1). HONEYWELL FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions: (1) This Device may not cause harmful interfer- ence. (2) This device must accept any interference received, including interference that may cause undesired operation. FCC ID: CFS8DL-GRIPAIO7 IC: 573F-GRIPAIO7 IC MODEL: GRIPAIO7 800-24167 2/18 Rev A FCC ID: CFS8DLWFZW CONTAINS MODULE: FCC ID: CFS8DLWFZW CONTAINS MODULE: IC:573F-WFZW IC:573F-WFZW grip-020-V0 Figure 1. FCC/IC Label Location (ADT7AIO Shown) 2. Remove the screw securing the rear case to the front case. 3. Slide the rear case down and separate from the front case. 4. Remove the communication module access cover. 5. Insert the ADTZWM into the slot on the left side of the control as shown in Figure 2 and ensure the receptacle is securely seated on the control’s edge connector. 6. Secure the module with the provided SCREW SCREW screw. 7. Re-install the communication module access cover. 8. Install the rear case and secure with the screw. COVER grip-011-V0 Figure 2. Installing the ADTZWM Module (ADT7AIO Shown)

Installing the Module in the ADTHYBWL Series 1. Affix the provided FCC/IC label (ADTZWM, P/N 800-24286) on the ADTHYBWL cabinet (refer to Figure 3) HONEYWELL GRIP HYBRID CONTROLLER FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions: (1) This Device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. FCC ID: CFS8DL-GRIPH IC: 573F-GRIPH For Patent Information see: www.honeywell.com/patents HVIN: GRIPH Country of Origin: Mexico 800-24232 3/18 Rev A Model LCP500-L 800-21465 10/15 Rev.A ETL Listed Household Fire and Burglar 3091091 Warning Unit Conforms to UL STD 985, 1023, 1635 Classified to ANSI/SIA CP01-2010 NOT TO INTERNET SLOT 1 SLOT 2 CONNECTION USED LTE WiFi / ZWAVE AUX/BELL_OC LED TAMPER RUN LED 24-HR BATTERY THIS EQUIPMENT SWITCH IB2/ACTIVE LED STANDBY REQUIRED GENERAL SHOULD BE SLOT 3 INSTALLED RESERVED LED FOR FIRE IN ACCORDANCE RJ-45 INSTALLATIONS. WITH THE NATIONAL CONNECTOR USE 12V, 7AH FIRE PROTECTION BATTERY FOR ASSOCIATION'S 120mA AUX POWER. FCC ID: CFS8DLWFZW STANDARD 72 SEE INSTRUCTIONS. (NATIONAL FIRE PROTECTION ASSOCIATION, BATTERY CAPACITY FOR EMERGENCY BATTERYMARCH BURGLARY STANDBY USE AT LEAST PARK, QUINCY, BATTERY POWER LED 4 HRS. CONTAINS MODULE: MA 02169). PRINTED INFORMATION AC POWER LED CHARGING VOLTAGE 13.8VDC. DESCRIBING MAXIMUM CHARGING CURRENT INSTALLATION, 650mA. TESTING, MAINTENANCE, BATT+ BATT - SEALED LEAD-ACID TYPE. BATTERY EVACUATION NORMALLY NEED NOT BE REPLACED TRIGGER 2 TRIGGER 1 PLANNING AND FOR AT LEAST THREE YEARS REPAIR SERVICE IS USED TRIGGER OUTPUT 1: 100mA MAX TO DETERMINE TOTAL STANDBY LOAD NOT TO BE PROVIDED WITH THIS TRIGGER OUTPUT 2: 100mA MAX ON BATTERY, ADD 100mA TO TOTAL OF GND 12V EQUIPMENT. AUX. POWER AND REMOTE TOUCHPAD CURRENTS CONNECTION OF BLACK 8-PIN TRIGGER AUX OUTPUT LED THE FIRE ALARM - + A B SIGNAL TO A FIRE CONNECTOR ALARM HEAD- RED QUARTERS OR CENTRAL STATION EARTH GROUND SHALL BE PERMIT- TED ONLY WITH HI THE PERMISSION SEE IC:573F-WFZW GND AUX LO OF THE LOCAL INSTRUCTIONS** AUTHORITY HAVING FOR PROPER JURIDICTION. THE GROUNDING } BLACK: TOUCHPAD GND (-) RETURN BURGLAR ALARM AUX. PWR FCC ID: CFS8DLWFZW SIGNAL SHALL NOT OUTPUT BE CONNECTED 10.5-13.8VDC LO LO LO LO LO RED: TOUCHPAD POWER (+) HI HI HI HI HI HI HI TO A POLICE CONTAINS MODULE: YELLOW: TOUCHPAD IB2A 200mA MAX. GREEN: TOUCHPAD IB2B LO LO EMERGENCY (120mA MAX. RECHARGEABLE BATTERY NUMBER FOR UL (12V, 7AH) DC - DC+ INSTALLATIONS) SEALED LEAD ACID TYPE ALL OUTPUTS 820 OHMS ZONE 1 ARE POWER EOLR ALARM USE FOR OUTPUT LIMITED. 2-WIRE SMOKE 10.5–13.8VDC, DETECTORS 2A MAX. (600mA ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 300-10211 IC:573F-WFZW MAX. FOR UL USAGE, INCLUDING 13.5 VDC, 1.8A MAXIMUM AUX POWER) POWER NUMBER OF STEADY FOR SUPPLY TO 2-WIRE SMOKE 2000 2000 2000 2000 2000 2000 2000 2000 BURGLARY/PANIC, 10VAC DETECTORS OHMS OHMS OHMS OHMS OHMS OHMS OHMS OHMS TEMPORAL PULSE A LA R M STATU S TRO U B LE CANCEL UNSWITCHED ON ZONE 1 EOLR EOLR EOLR EOLR EOLR EOLR EOLR EOLR SOUNDING FOR FIRE. OUTLET AWAY STAY 1 2 3 IS 16 USE 702 SIREN, OR PA N I C O FF 4 5 6 (24HR) MAX. ZONE RESISTANCE: (EACH ZONE) 300 OHMS (PLUS EOLR) 12V BELL. SEE MAX TEST B YPA SS DC+ (USE EOLR PART NUMBER P4100 PART OF KIT SAHDWR1) INSTRUCTIONS. 7 I N STA N T 8 CODE 9 C H I ME FOR BELL R EA DY 0 # DC - SUPERVISION, AND ** FOR COMPLETE INFORMATION SEE INSTRUCTIONS 800-24126 OR HIGHER CONNECT RESISTOR DIRECTLY ACROSS WTP100 WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM. IN ADDITION, THIS EXTERNAL SOUNDER. TOUCHPAD ASSEMBLED IN MEXICO SYSTEM MUST BE CHECKED BY A QUALIFIED TECHNICIAN AT LEAST ONCE EVERY THREE (3) YEARS. 1501 Yamato Road Boca Raton, Florida 33431 ADTHYBWL-Series - Summary of Connections © 2018 ADT Security Services 800-24129 2/18 Rev.A grip-028-V0 Figure 3. FCC/IC Label Location 2. Install the ADTZWM (ZWAVE) on the edge connector on the PCB (refer to SCREW Figure 4). Ensure the receptacle is securely seated on the edge connector. 3. Secure the module with the provided screw. EXT INT LTE WiFi ADTZWM TX RX GND MODULE GENE RAL TX RX GND BATT+ GND grip-012-V0 Figure 4. Installing the ADTZWM Module Programming 1. The ADTZWM requires a router and internet service for Wi-Fi connection. 2. Programming associated with the ADTZWM module is accomplished via the MobileTech app, as part of the control panel programming. Refer to the control panel installation and setup guide for additional information.

Specifications ADTZWM Board Dimensions: 1.625” W x 2.625” L x 0.3125” D Current Drain: TBD Input Voltage: TBD Temperature: 32°F (0°C) to 140°F (60°C) REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE CONTROL WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE SYSTEM. FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC CLASS B STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • If using an indoor antenna, have a quality outdoor antenna installed. • Reorient the receiving antenna until interference is reduced or eliminated. • Move the radio or television receiver away from the receiver/control. • Move the antenna leads away from any wire runs to the receiver/control. • Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. • Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’Industrie Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable. RF Exposure Warning The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. ! Mise en Garde Exposition aux Frequences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes. USE OF THESE PRODUCTS IN COMBINATION WITH NON-HONEYWELL PRODUCTS IN A WIRELESS MESH NETWORK, OR TO ACCESS, MONITOR OR CONTROL DEVICES IN A WIRELESS MESH NETWORK VIA THE INTERNET OR ANOTHER EXTERNAL WIDE AREA NETWORK, MAY REQUIRE A SEPARATE LICENSE FROM SIPCO, LLC. FOR MORE INFORMATION, CONTACT SIPCO, LLC OR IPCO, LLC AT 8215 ROSWELL RD., BUILDING 900, SUITE 950, ATLANTA, GA 303350, OR AT WWW.SIPCOLLC.COM OR WWW.INTUSIQ.COM

WARRANTY INFORMATION For Technical Support, call 1-877-748-7628, option 3 For documentation, call Customer Service at: 1-800-238-2727 (1-800-ADT-ASAP). For the latest warranty information, please go to: www.honeywell.com/security/hsc/resources/wa. Warranty Patents For patent information, see www.honeywell.com/patents ADT Security Services 1501 Yamato Road Boca Raton, FL 33431 © 2018 ADT Security Services Ê800-24197eŠ 800-24197 3/18 Rev. A (BETA)


Document Created: 2018-06-21 09:13:19
Document Modified: 2018-06-21 09:13:19
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC