User Manual_20180410_v1 - SiXC2W EXHIBIT 7-1 Install Guide

FCC ID: CFS8DL6C2W

Users Manual

Download: PDF
FCCID_3822314

SiXC2W Convert to Wireless / Convert to Wireless Quick Installation Guide Guide d'installation rapide The Honeywell SiXC2W is an eight zone hardwire to wireless converter used with The Honeywell SiXC2W is an eight zone hardwire to wireless converter used with controllers that support Honeywell’s SiX™ series devices. It is useful in retrofit 12- controllers that support Honeywell’s SiX™ series devices. It is useful in retrofit 12-volt volt security system applications where existing contact wiring was used. It uses security system applications where existing contact wiring was used. It uses those those existing wired contacts and converts them to wireless. existing wired contacts and converts them to wireless FEATURES CARACTÉRISTIQUES • Provides 12-volts for devices such as motion detectors, glass breaks, etc. • Provides 12-volts for devices such as motion detectors, glass breaks, etc. NOTE: Only two devices may be powered using the auxiliary output on the NOTE: Only two devices may be powered using the auxiliary output on the SiXC2W. SiXC2W. • Provides 24-hour battery backup. (4-hour if external devices are connected). NOTE: • Provides 24-hour battery backup (4-hour if external devices are connected). It immediately sends a power loss signal to the controller in the event the power is NOTE: It immediately sends a power loss signal to the controller in the event lost. the power is lost. • When no battery is connected, low battery message will send to control panel. • When no battery is connected, low battery message will send to control When battery is connected, and if battery voltage drops below 3.6VDC, a low battery panel. message sends to the control panel. When battery is connected, and if battery voltage drops below 3.6VDC, a low When only the battery is connected, and if the battery voltage 3.4 V, system will shut battery message sends to the control panel. down. When only the battery is connected, and if the battery voltage 3.4 V, system • Support one button calibration will shut down. • Automatic zone configuration • Support one button calibration • Easy setup in three steps • Automatic zone configuration • Cover tamper protection • Easy setup in three steps • Cover tamper protection IMPORTANT! Not to be used for fire, heat, or carbon monoxide detectors. IMPORTANT! Not to be used for fire, heat, or carbon monoxide detectors. CALIBRATING CALIBRATING The calibration process enables the SiXC2W to learn The calibration process enables the SiXC2W to learn what zones are to be active and what value EOL resistors what zones are to be active and what value EOL are used. resistors are used. IMPORTANT! IMPORTANT! Unused zones that are open ARE NOT Unused zones that are open ARE NOT recognized and reported. recognized and reported 1. Ensure all zones are connected and not faulted. 1. Ensure all zones are connected and not faulted. 2. On the SiXC2W, press and release the top middle 2. On the SiXC2W, press and release the top middle button. button. 3. Indicator LED #2 will flash Red for 1/2 second; 3. Indicator LED #2 will flash Red for 1/2 second; then then LED #3 turns steady Green. LED #3 turns steady Green. 4. Calibration is in process 4. Calibration is in process 5. DONE. The SiXC2W is calibrated and ready to 5. DONE. The SiXC2W is calibrated and ready to enroll enroll in the control panel. in the control panel. NOTES: NOTES: • If the SiXC2W loses both AC and battery backup • If the SiXC2W loses both AC and battery backup power, the zone calibration data is retained. power, the zone calibration data is retained. • If there is an existing resistor, it MUST have a value • If there is an existing resistor, it MUST have a value between 1K and 10K.The unit comes with eight (8) between 1K and 10K.The unit comes with eight (8) 2.2K resistors for zones that don’t have one. 2.2K resistors for zones that don’t have one. IMPORTANT! IMPORTANT! Once the SiXC2W is calibrate, any change in Once the SiXC2W is calibrate, any change in the the zone resistance the module must be zone resistance the module must be re-calibrated. re-calibrated. ENROLLING / ENROLLING Lyric Control Lyric Control Lyric Controller Enrollment Process, See Controller’s installation instructions for its Lyric Controller Enrollment Process, See Controller’s installation instructions for it’s proper programming process. proper programming process. For Lyric Gateway For Lyric Gateway Use AlarmNet 360™ to enroll and program this sensor. Use AlarmNet 360™ to enroll and program this sensor. For Other Controls For Other Controls For other controls that support SiX series devices, see the controller’s installation app for For other controls that support SiX series devices, see the controller’s installation app for details details NOTE: Once enrolled in a system, the SiXC2W cannot be used with another controller NOTE: Once enrolled in a system, the SiXC2W cannot be used with another controller until it is removed from the current controller. See the Controller’s instructions until it is removed from the current controller. See the Controller’s instructions for details. for details.

MOUNTING / MONTAGE Signal strength: • Rang of 1-4 bars (green), should be a minimum 1 green bar for the zone being programmed. • Four Red Bards indicate poor signal strength; the device should be relocated. • See the controller’s instruction for bar indication signal strength values. Icon Description Signal Strength 4 Green Bars 3 Green Bars Good 2 Green Bars 1 Green Bar 4 Red Bars Relocate TAMPER/LOW BATTERY REPORTING TAMPER/LOW BATTERY REPORTING The SiXC2W reports this condition to the control. If a low battery or tamper condition The SiXC2W reports this condition to the control. If a low battery or tamper condition exists all zones used on the module shows a trouble on the control. exists all zones used on the module shows a trouble on the control. IMPORTANT: IMPORTANT: The first battery test occurs 1 hour after power up. To quickly verify a good The first battery test occurs 1 hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system backup battery, unplug and then plug back in the power supply; the system will will perform a battery test within 1 minute. perform a battery test within 1 minute. LED INDICATIONS BATTERY REMOVAL AND INSTALLATION LED # / LED # Functions / Functions 1 (Green / Green) Blinks once upon RF signal transmission (HW zone trigger/tamper and/or a fault message), slow blink for a cover tamper, quick blinks for enrollment or deletion / Blinks once upon RF signal transmission (HW zone trigger/tamper and/or a fault message), slow blink for a cover tamper, quick blinks for enrollment or deletion 2 (Red / Red) Blinks 1s / 1s off when module needs calibrating / Blinks 1s / 1s off when module needs calibrating 3 (Green / Green) Steady on when the module has been calibrated. / Steady on when the module has been calibrated. 4 (Green and Red / Green: 5VDC Power from the plug-in transformer is present Green and Red) Red (blinking 1sec on / 1 sec off): Running on battery, DC power not present. / Green: 5VDC Power from the plug-in transformer is present Red (blinking 1sec on / 1 sec off): Running on battery, DC power not present. Approval Listings / Approbations Homologations: FCC / IC - ETL Listed to UL268 & 521 cETL Listed to ULC S530 & S531 Other Standards / Autres normes: RoHS Caution: The batteries used in this device may present a fire or chemical burn FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA hazard if mistreated. Do not recharge, disassemble, heat above 212°F STATEMENTS (100°C) or dispose of in fire. Use Panasonic CR123A or DURACELL DL123, The user shall not make any changes or modifications to the equipment unless DL 123A Lithium batteries. Use of other batteries may present a risk of fire or authorized by the Installation Instructions or User's Manual. Unauthorized changes explosion. Keep used batteries away from children. Dispose of used batteries or modifications could void the user's authority to operate the equipment. properly. Remove old batteries. Wait 10 seconds and then replace with four new FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and batteries. To avoid a low battery indication when installing new batteries, both Industry Canada’s license-exempt RSSs. Operation is subject to the following two batteries must be installed within 15 seconds of installing the first one. Any conditions: (1) This device may not cause harmful interference, and (2) This device low battery condition that may have occurred should clear when the back must accept any interference received, including interference that may cause plate is installed. undesired operation. Mise en garde : Les piles utilisées dans ce dispositif peuvent présenter des Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence risques d'incendie ou de brûlure chimique si elles sont mal traitées. Ne RSS d’Industrie Canada. Son fonctionnement est soumis aux conditions suivantes: rechargez pas, ne désassemblez pas, ne faites pas chauffer et ne jetez pas au (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit feu les piles à plus de 100 °C (212 °F). Utilisez des piles au lithium accepter toute interférence reçue y compris les interférences causant une Panasonic CR123A ou DURACELL DL123, DL 123A. L'utilisation d'autres réception indésirable. types de piles peut présenter des risques de feu ou d'explosion. Gardez les vieilles piles hors de la portée des enfants. Débarrassez-vous des batteries SPECIFICATIONS / SPÉCIFICATIONS: utilisées de façon appropriée. Retirez les vieilles piles. Attendez 10 secondes et remplacer-les par quatre Voltage Transformer Part # ................................... 300-10259 nouvelles piles. Pour éviter une indication de piles faibles lorsque vous Input Voltage ............................................... 100 ~ 240VAC, 50 ~60 Hz installez de nouvelles piles, les dos (2) piles doivent être installées en deçà de Operating Voltage ..................................... 5VDC 15 secondes après l'installation de la première. Toute condition de pilles Maximum Transformer Distance ...... 9.8ft. (3m) faibles qui aurait pu se produire devrait être rétablie une fois la plaque arrière Voltage Output ........................................... 12VDC @ 100mA (Up to three sets of 20–24 installée. gauge wiring) REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH Battery/ Pile ................................................. P/N 300-10342 WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. Environmental POUR LES LIMITES DU SYSTÈME D’ALARME AU COMPLET, REPORTEZ- Operating Temp ......................................... 14 F (-10C) to 140F (60C) VOUS AU GUIDE D’INSTALLATION DU PANNEAU DE COMMANDE NOTE: Charging the lithium battery stops when temperature is below 32F See Honeywell Installation Guide P/N Voir les instructions d'installation (0C) 800-24139– complètes 800-24139- Relative Humidity ...................................... 95%, Non-condensing / 95% max. sans https://mywebtech.honeywell.com/. https://mywebtech.honeywell.com/. condensation Support / Pour de l’assistance en ligne, visitez : Physical https://mywebtech.honeywell.com/ Dimensions .................................................. Length 7.0 in (178 mm) x U.S. warranty / U.S. garantie: www.honeywell.com/security/hsc/resources/wa Width 4.5 in (114 mm) x For patent info, see: / Pour des informations sur les brevets, voir : Depth 1.5 in (38mm) www.honeywell.com/patents Mounting Hardware ................................. Double stick tape and screws Zone Resistance......................................... 1K to 10K Ohm EOL Resistors Zone Wiring .................................................. 1,000ft (Each Zone) Radio Frequency Transmission Range ................................ 300ft (91.5m) MyWebTech Warranty / Garantie Patents / brevets  2018 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved.


Document Created: 2018-03-20 10:26:07
Document Modified: 2018-03-20 10:26:07
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC