User Guide

FCC ID: CFS8DL6160RF-3

Users Manual

Download: PDF
FCCID_4480051

K0904V1 2/06 Rev. B ADEMCO 6160RF Keypad/Transceiver User Guide KEYPAD DISPLAYS AND LEDS Whether these panic keys function and the type of panic alarms they produce is determined by the control The 6160RF has the following features: panel’s capability and programming. (Check with your • Large backlit, 2-line, 32-character alphanumeric installer for the availability and type of alarm of these LCD. panic keys.) • 16 large telephone-style backlit keys located behind a Special Function Keys - These are the four keys decorative door that swings down to provide access to located to the left of the numeric keys (see below). The the keys. keys may be programmed by your installer for panic • System numerals, imprinted in large type on the keys alarms or other special functions such as single-button for easy identification. System functions appear below arming (Check with your installer to see which options the keys on the keypad. are available with your system.) The following table shows the LEDs and their functions: Special function keys and function key pairs must be LED Function held down for at least 2 seconds to activate an alarm. ARMED Lights when the system is armed in any mode. A set of adhesive labels with typical panic symbols is (Red) provided. Place the appropriate label in the indented READY Lights when the system is ready to be armed (no zone faults are present). area on each key, so that the user can easily identify (Green) each key’s function. FUNCTION KEYS AND LABELS SOUNDER The function keys are continuously backlit for ease in The built-in speaker has the following functions: use. (Check the User Guide that accompanies the control • Produces warning sounds during alarm and trouble panel for detailed instructions on the use of these keys.) conditions, and also during entry/exit delay periods. Function Keys - The function keys include keys for Provides acknowledgment tones when keys are panic alarm activation. The panic alarms are activated pressed, and confirmation tones for successful by pressing key pairs [1] & [*], [3] & [#], or [*] & [#], or command entries. a Special Function Key. ARMED 2 3 OFF AWAY STAY SPECIAL READY 4 5 6 PANIC FUNCTION MAXIMUM TEST BYPASS KEY KEYS 7 8 9 PAIR INSTANT CODE CHIME 0 # READY PANIC KEY PAIR PANIC KEY PAIR 6160RF-001-V1 6160RF Keypad/Transceiver (front door removed) TROUBLESHOOTING The error messages listed in the following table cause the keypad to produce a single ding tone. The table describes the error messages and the corrective actions. Display Corrective Action Low Bat (with Zone No.) 1. Replace the battery if the wireless transmitter has a replaceable battery. 2. Replace the transmitter if the wireless transmitter does not have a replaceable battery. Open Ckt Contact your Installer. Check 100 Contact your Installer.

FEDERAL COMMUNICATIONS COMMISSION STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • If using an indoor antenna, have a quality outdoor antenna installed. • Reorient the receiving antenna until interference is reduced or eliminated. • Move the radio or television receiver away from the receiver/control. • Move the antenna leads away from any wire runs to the receiver/control. • Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. • Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC/IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences causant une reception indésirable. ‡K0904V1DŠ 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 Copyright © 2011 Honeywell International Inc. K0904V1 2/06 Rev. B www.honeywell.com/security


Document Created: 2012-01-12 10:12:02
Document Modified: 2012-01-12 10:12:02
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC