Installation Manual 7-1 Part 1

FCC ID: CFS8DL-GRIPH

Users Manual

Download: PDF
FCCID_3919557

ADT ADTHYBWL Series Security Systems Ref: ADTHYBWL Series Quick Installation Guide Mount the Control Connect the Power Supply & Battery (Continued) Program the Control 1, Open the cabinet door fully and remove by pulling UL For UL installations and Residential fire installations, refer to the chart below for the correct Refer to the to the MobileTech installer app for programming instructions. to the left. battery size required to meet the mandatory standby time. 2. Remove the cabinet knockouts needed for wiring OUTPUT LIMITATIONS AND REQUIRED BATTERIES Test the System entry. Output Current Limits Battery Information Refer to the Refer to the MobileTech installer app for testing instructions. 3. Mount the control cabinet to a sturdy wall in a clean, dry area, which is not readily accessible to SECURE WITH Battery Capacity Recommended the general public, using fasteners or anchors (not SCREW Current Total Max. Aux. Current (Amp/Hrs) Battery (Yuasa No.) supplied) with the four cabinet mounting holes. 600mA maximum total of 110mA 7AH NP7-12 Major Features and Capacities auxiliary power plus bell 4. Install the ADTZWM (Wi-Fi® and Z-Wave®) and/or output currents ADTLTE Communication Module(s) (if used). Feature Details 5. When installation, wiring and programming is Partitions 4 completed, install the cabinet door and secure with Connect Devices, Zones and Sounder Hardwire Zones 8 (1-7 and one dedicated smoke zone) the provided screw. Refer to the Wiring Diagram on the reverse side for connection information. NOTE: This Maximum Devices 250 Devices (includes sensors, keypads, keyfobs, touch system uses a range of reserved addresses for each type of device. screens, Z-Wave, Bluetooth (for mobile devices), cameras OPTIONAL KEY LOCK: If desired, a key lock can be Securing the Cabinet Door and wiselink) installed (K4445V1). See Installation Instructions for 1. Connect keypads and other devices. • 128 SiX Series sensors details. Wire Total Current of All Devices Connected to a Single Wire Run Size 50 mA or less 100 mA 300 mA 500 mA 600 mA • 32 Keyfobs (8 button) MOUNTING HOLES (3) #22 900ft (274m) 450ft (137m) 150ft (46m) 90ft (27m) 75ft (23m) • 6 Bluetooth (BLE Phones) #20 1400ft (427m) 700ft (213m) 240ft (73m) 140ft (43m) 120ft (37m) • 8 Touchpads/Touchscreens #18 1500ft (457m) 1100ft (335m) 350ft (107m) 220ft (67m) 170ft (52m) • 8 Motion Viewers #16 1500ft (457m) 1500ft (457m) 550ft (168m) 350ft (107m) 270ft (82m) • TBD Z-Wave Devices The length of all wire runs for both partitions combined must not exceed 4000 feet (1219m) when unshielded • TBD IP Cameras quad conductor cable is used or 2000 feet (610m) if shielded cable is used. Security Codes (Users) 96 Includes Master User (#1) LTE WiFi TX RX GND GENERA L TX RX GND BATT+ GND • Do not locate the receiver or transmitters on or near metal objects. This will decrease range Outputs 18 TAMPER and/or block transmissions. On-Board Triggers 2 • Do not locate in an area of high RF interference (indicated by frequent or prolonged lighting of the receiver’s LED; random flicker is OK). • Do not locate RF receiver closer than 10 feet from any keypads. Specifications Touchpad (WTP100) Dimensions: 10-5/16” W x 12-1/4” H x 3.5” D (262mm x 311mm x 89mm) • Connect touchpad field wiring to the GND, AUX, A and B terminals. Electrical: Relay Modules Voltage Input: 13.5VDC, 1.8A from plug-in power supply, Part No. 300- MOUNTING HOLES (3) • Connect desired field wiring to the module’s relay contact terminals. (when available) 10211 or 300-10211-CAN (Canada) Mounting the Cabinet Communication Module (refer to the documentation provided with the module.) Alarm Sounder: 10.5-13.8VDC, 2.0 Amp output can drive 12V Bell or 702 Auxiliary Power Output: 10.5-13.8VDC, 200mA max. Optional ADTZWM and ADTLTE Communications Module Note: Refer to the Specific • LTE (ADTLTE Series) • WiFi/Z-Wave (ADTZWM) Backup Battery 12VDC, 7AH (sealed lead acid type). Charging Voltage: Module Installation section in the online Installation & Reference Guide for instructions on mounting this module. 13.8VDC 2. Connect hardwire zones to the appropriate zone terminals. Communication Formats: 4-digit Contact ID 3. On-Board Trigger Connections Maximum Zone Zones 1–8 = 300 ohms excluding EOLR standard zones Connect the Power Supply & Battery • Connect field wiring to the appropriate trigger pin using the 4-wire cable (N4632-4, not Resistance: Power Supply (P/N 300-10211 or 300-10211-CAN in Canada) supplied). • Do not plug power supply into the AC outlet until all wiring connections to the control are • Trigger outputs will go low on power-up. WARRANTY INFORMATION complete. As a safety precaution, always power down the control when making such connections. 4. Connect the external sounder to the GND and BELL terminals. • If not using bell supervision, connect the supplied 820 ohm resistor across the GND and BELL For the latest warranty information, please go to: Battery Connections terminals. If using bell supervision, see the next bullet point. www.honeywell.com/security/hsc/resources/wa. • After all connections to the control are completed and after AC power has been applied, connect the red and black flying leads on the control board to the battery. • If supervised output desired, see Sounder Supervision wiring diagram on reverse side, and Warranty Patents For patent information, see www.honeywell.com/patents • IMPORTANT: This control will not power-up on battery alone (AC power must be applied). program accordingly. However, once the system is powered up, it will operate on battery if AC is lost. 5. Install Wireless Zone Transmitters (Programmed via alarm.com). CALIFORNIA STATE FIRE MARSHALL (CSFM) AND UL RESIDENTIAL FIRE 24-HOUR BATTERY BACKUP REQUIREMENTS FOR DOCUMENTATION AND SUPPORT The California State Fire Marshal and UL have regulations which require that all residential fire See Installation and Reference Guide P/N 800-24125 or higher, which can be alarm control panels must be provided with a backup battery which has sufficient capacity to operate the panel and its attached peripheral devices for 24 hours in the intended standby condition, ordered by contacting Customer Service at 1-800-238-2727 (1-800-ADT-ASAP). For followed by at least 4 minutes in the intended fire alarm signaling condition. This control panel can technical support please call the ADT Product Support Group at 1-877-748-7628, meet these requirements without using a supplementary power supply, provided that the panel’s option 3. auxiliary power and bell output currents are limited as listed. Ê800-24126$Š A D T S e c u r i t y S e r vi c e s 1501 Yamato Road 800-24126 2/18 Rev. A Part 1 (BETA) Boca Raton, FL 33431 © 2 0 1 8 A D T S e c u r i t y S e r vi c e s

TO WiFi / ZWAVE SLOT 2 TO LTE SLOT 1 COMM TO INTERNET SLOT 1 SLOT 2 CONNECTION TEST LTE WiFi / ZWAVE INT AUX/BELL_OC LED TAMPER RUN LED SWITCH EXT IB2/ACTIVE LED GENERAL SLOT 3 RESERVED LED RJ-45 CONNECTOR EARTH GROUND CONNECTION THIS CONTROL DOES NOT NORMALLY NEED AN EARTH GROUND FOR RESISTANCE TO DAMAGE FROM LIGHTNING AND ELECTRICAL DISCHARGE. FOR ADDITIONAL PROTECTION IN AREAS OF SEVERE ELECTRICAL ACTIVITY, CONNECT TERMINAL 25 TO A GOOD EARTH ADTZWM MODULE ADTLTE MODULE BATTERY POWER LED GROUND. EXAMPLES OF GOOD EARTH GROUNDS: AC POWER LED METAL COLD WATER PIPE: USE A NON-CORROSIVE METAL STRAP (COPPER IS RECOMMENDED) BATT+ BATT - FIRMLY SECURED TO THE PIPE TO WHICH THE GROUND LEAD IS ELECTRICALLY CONNECTED AND SECURED. TRIGGER 2 TRIGGER 1 USED TRIGGER OUTPUT 1: 100mA MAX BLACK NOT TRIGGER OUTPUT 2: 100mA MAX GND 12V RED HARDWIRE ZONE CONNECTION AUX OUTPUT LED 8-PIN TRIGGER GND AUX B A CONNECTOR 1. OPEN CIRCUIT DEVICES CONNECT IN PARALLEL ACROSS THE LOOP; FOR EOLR ZONES, CONNECT THE EOLR RECHARGEABLE BATTERY ACROSS THE LOOP WIRES AT THE LAST DEVICE. (12V, 7AH) SEALED LEAD ACID TYPE GND HI AUX 2. CLOSED CIRCUIT DEVICES CONNECT IN SERIES IN THE LO HIGH (+) SIDE OF THE LOOP; FOR EOLR ZONES, CONNECT THE EOLR IN SERIES FOLLOWING THE LAST DEVICE. } 3. USE ZONE 1 FOR 2-WIRE SMOKE DETECTORS. MAXIMUM AUX. PWR OUTPUT NUMBER OF 2-WIRE SMOKE DETECTORS IS 16. AC POWERAC POWER AND CONNECTION BATTERY CONNECTION LO LO LO LO LO HI HI HI HI HI HI HI 10.5-13.8VDC 200mA MAX. LO LO EOLR NOTE: (120mA MAX. TRANSFORMER DC - DC+ FOR UL IF THE EOLR IS NOT AT THE END OF THE LOOP, THE INSTALLATIONS) 1. CONNECT THE POWER SUPPLY TO THE GND AND AC+ TERMINALS. ZONE IS NOT PROPERLY SUPERVISED AND THE SYSTEM 820 SEE WIRE RUN CHART. POWER SUPPLY WIRE RUNS ALL OUTPUTS OHMS EOLR MAY NOT RESPOND TO AN "OPEN" ON THE ZONE. ARE POWER ALARM OUTPUT EARTH USE CAUTION WHEN WIRING GROUND Distance from control Wire Size LIMITED. 10.5–13.8VDC, THE POWER SUPPLY TO THE ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 UL NOTE: 2A MAX. (600mA Up to 25 feet # 22 MAX. FOR UL CONTROL. FOR UL COMMERCIAL BURGLARY ALARM INSTALLATIONS, 25 - 50 feet # 20 USAGE, INCLUDING USE EOLR ZONES. 2000 2000 2000 2000 2000 2000 2000 2000 AUX POWER) 50 - 75 feet # 18 STEADY FOR 4. USE EOLR PART NUMBER P4100 (PART OF KIT SAHDWR1). OHMS OHMS OHMS OHMS OHMS OHMS OHMS OHMS BURGLARY/PANIC, 75 - 150 feet # 16 EOLR EOLR EOLR EOLR EOLR EOLR EOLR EOLR TEMPORAL PULSE SOUNDING FOR FIRE. USE 702 SIREN, OR NOTE: DO NOT CONNECT TO A RECEPTCLE CONTROLLED BY BLACK: TOUCHPAD GND (-) RETURN 12V BELL. SEE A SWITCH. 2-WIRE SMOKE DETECTORS SOUNDER CONNECTION INSTRUCTIONS. FOR BELL 2. AFTER ALL WIRING CONNECTIONS ARE COMPLETE, PLUG RED: TOUCHPAD POWER (+) SUPERVISION SEE GREEN: TOUCHPAD IB2A YELLOW: TOUCHPAD IB2B IF NOT USING A SOUNDER SOUNDER POWER SUPPLY INTO A 110VAC UNSWITCHED OUTLET (24HR). Detector Type System Sensor CONNECT THE 820 OHM BELL RESISTOR ACROSS CONTROL’S CONNECTION NOTES. "AC LOSS" DISPLAYED IF VOLTAGE FALLS BELOW 11 VDC. Model No. BELL AND GND TERMINALS OTHERWISE SEE SOUNDER SUPERVISION BELOW. BATTERY Photoelectric 2WT-B 1. PLACE THE 12-VOLT BACKUP BATTERY IN THE CABINET. w/heat sensor IF USING A SOUNDER CONNECT SOUNDER TO BELL AND GND TERMINALS. 2. AFTER ALL CONNECTIONS TO THE CONTROL ARE MADE AND Photoelectric 2W-B 300-10211 13.5 VDC, 1.8A AFTER AC POWER HAS BEEN APPLIED, CONNECT THE RED AND Photoelectric 2151 w/B110LP base SOUNDER ACTIVATES UPON ALARM EVENT. POWER BLACK FLYING LEADS TO THE BATTERY. SUPPLY ALARM OUTPUT: 10.5–13.8VDC, 2A MAX. (600mA MAX. FOR TO 110VAC IMPORTANT: THE PANEL WILL NOT POWER UP INITIALLY ON UL USAGE, INCLUDING AUX POWER). UNSWITCHED BATTERY POWER ONLY. YOU MUST PLUG THE POWER SUPPLY STEADY FOR BURGLARY/PANIC. ALARM S TAT U S T RO U B L E OUTLET (24HR) IN FIRST, AND THEN CONNECT THE BATTERY. 4-WIRE SMOKE DETECTOR CONNECTIONS CANCEL + TEMPORAL PULSE SOUNDING FOR FIRE. 1 AWAY 2 STAY 3 DC+ UL: MUST BE A UL LISTED AUDIBLE SIGNAL APPLIANCE RATED POWER SHUTDOWN NOTE: TERMINALS PA N IC OFF 4 5 6 DC - AUX PWR OUTPUT RELAY FOR 10.2-13.8 VDC AND BE MOUNTED INDOORS. MAX 7 TEST 8 B Y PA S S 9 SYSTEM SHUTS DOWN SENSOR DETECTION PROCESSING IF PROGRAM RELAY BLK _ + RED IN S TA N T CODE 0 C H IM E # CONTROL’S VOLTAGE DROPS BELOW 9.6V. AS ZONE TYPE USE ADEMCO No. 702 SIREN, OR 12V BELL. R E A DY FIRE ZONE RESET _ WTP100 N.C. N.O. A BATTERY MUST BE INSTALLED BECAUSE THE BATTERY TOUCHPAD OR EOL SUPPLIES THE SOUNDER CURRENT. CONTACT OPENS MOMENTARILY POWER UPON FIRE ALARM RESET SUPERVISION UL: BELL SUPERVISION IS REQUIRED FOR FIRE ALARM INSTALLATIONS. EXTERNAL ALARM SOUNDER RELAY TO OUTPUT TBD + VIOLET MODULE EOLR-1. CONNECT AN 820 OHM KEYPADS AND ADDRESSABLE _ RESISTOR ACROSS THE PROGRAM OUTPUT TBD FOR "OUT NORM LOW" 4-WIRE SMOKE USE N.O. CONTACT, LAST EXTERNAL GND TERM. 820 OHM DEVICE CONNECTION AND AS FIRE ZONE RESET OR COMBUSTION 2000 WHICH SOUNDER AS SHOWN BY OBSERVE WEEKLY TESTING IS REQUIRED TO ENSURE PROPER MAX. CURRENT = 100 mA DETECTOR OHMS THE DOTTED LINE. EOL CLOSES BELL TERM. POLARITY RESISTOR OPERATION OF THIS SYSTEM. IN ADDITION, THIS CONNECT KEYPADS AND OTHER ADDRESSABLE DEVICES TO A, B, EOLR WHEN POWER IS SYSTEM MUST BE CHECKED BY A QUALIFIED AUX AND GND TERMINALS. APPLIED. TECHNICIAN AT LEAST ONCE EVERY THREE (3) YEARS. (+) HEAT TO ZONE 1 7 TERM. DETECTOR (_) DO NOT CONNECT THE RESISTOR DIRECTLY TO THE ALARM OUTPUT TERMINALS! GRIP-quick-guide_CL-V0


Document Created: 2018-06-06 12:13:51
Document Modified: 2018-06-06 12:13:51
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC