User Manual_20180622_v1 - AIO 7-INCH EXHIBIT 7-1 Install Guide 1

FCC ID: CFS8DL-GRIPAIO7

Users Manual

Download: PDF
FCCID_3916805

ADT7AIO/ADT5AIO Series Installation and Setup Guide STEP 1 - Installing the Rechargeable Backup Battery and STEP 2 - Setting up the Communication Links Power Connector Note: Do not connect to a receptacle controlled by a switch. The control is designed to be placed on a desk/table top with the stand attached or 1. Plug the power supply into a 24-hour, 110VAC unswitched outlet. Upon power- mounted to a wall using the back plate/cover. up, the “Please Standby!” will be displayed on the home screen. 1. Remove the Control’s Case Back. 2. Connect the Control to the local router. 2. Install the ADTZWM (Wi-Fi® and Z-Wave®) and/or ADTLTE Communications modules (if used). 2. Connect the battery connector to the receptacle on the PC board. STEP 3 - Registration Programming and Testing 3. Insert the Battery Pack into the case. On a laptop, PC or Smart Device, go to: https://alarmadmin.alarm.com. 4. Secure the Battery Pack with the Battery Retainer using the Retaining Screw. 5a. Connect the power cable to the GND and +9V terminals on the AIO and to the + IMPORTANT: Once the programming procedure has started and the unit is and – terminals on the Power Supply. Refer to Table 1 for wire gauge and length. powered up, do not remove power or disconnect the battery, nor open the case. Do not apply power at this time. OR Disconnecting power or activating the tamper switch can cause unpredictable 5b Connect the power supply connector to the receptacle on the AIO. Do not apply programming results. power at this time. NOTE: If using the optional wall mount configuration, skip to the wall mounting Radio Activation procedure. If not, complete step 7. Refer to the https://alarmadmin.alarm.com for radio activation. 6. Install the Case Back onto the contorl and secure with the screw. Optional ADTZWM and ADTLTE Communications Module Note: Refer to the Specific Testing the System Module Installation section in the online Installation & Reference Guide for instructions on The following test modes are available: mounting this module. • Walk Test • Communication Diagnostics SCREW Enter Test mode (Walk Test) 1. After entering Installer Tools Menu Mode, select the “Test” button. 2. Select “Walk Test”. The system enters Walk Test Mode and “Walk Test-Home To BATTERY Quit” is displayed 3. Open each protected door and listen for three beeps from the keypad, followed by the zone’s Voice Descriptor. Identification of each faulted protection point should appear on the display, and clear when the door is closed. 4. Walk in front of the motion sensor and listen for three beeps and the zone’s voice descriptor. 5. When testing is complete, select the Home button and enter the Installer Code. SCREW SCREW 6. Press each key on the wireless key to confirm it performs its assigned function. COVER Specifications Dimensions: 7.875” W x 5.75” H x 1.0” D ADTZWM Voltage Input: P/N 300-10260: White – 9VDC, 2.5A MODULE EXT INT MACHINE P/N 300-10260-BK (Black) – 9VDC, 2.5A SCREW P/N 300-10260-CAN (Canada) – 9VDC, 2.5A 24-Hour Backup Battery: P/N 300-10186: Rechargeable Backup Battery: Lithium-ion battery pack rated at 3.6/4.2V, 7500 mAH Communication Formats: 4-Digit Contact ID ADTLTE Home Health Care Applications MODULE POWER IMPORTANT: In Home Health Care applications [UL1637] you must use pendant SUPPLY BATTERY model SiXMEDICAL. The maximum range is 50 ft. RECEPTACLE CONNECTOR grip-009-V0 GND Contacting Technical Support 9V TERMINAL BLOCK DETAIL A PLEASE, before you call Technical Support, be sure you: READ THE INSTRUCTIONS! Table 1 – Wiring Guide Maximum distance between Wire Gauge Note: Use UL-listed limited energy • Determine that the power supply and/or backup battery are supplying proper power supply and control (AWG) cable voltages. Up to 25 feet (7.62m) # 22 • Verify your programming information where applicable. • Note the proper model number of this product, and the version level (if known) Up to 45 feet (13.72m) # 20 along with any documentation that came with the product. Up to 70 feet (21.34m) # 18 • Note your ADT customer number and/or company name. Up to 110 feet (33.53m) # 16 Having this information handy will make it easier for us to serve you quickly and effectively. Mounting the Base to a Wall (Optional) For Documentation and Online Support For wall mounting, perform to the following: See Installation and Setup Guide P/N 800-24121 or higher, which can be 1. Secure the Mounting Plate to the wall with 4 screws. ordered by contacting Customer Service at 1-800-238-2727 (1-800-ADT- 2. Install the Tamper Screw as shown. ASAP). For technical support please call the ADT Product Support Group at 3. Secure the Control to the Mounting Plate by aligning the slots on the Base and 1-877-748-7628, option 3. sliding the unit down until locked in position. 4. Secure the Control with the screw. This system must be checked by a qualified technician at least once every three (3) years Ê800- Ê800-24121^Š 800-24121 5/18 Rev. A Part 1 (BETA)

The Limitations of this Alarm System Recommendations for Proper Protection While this system is an advanced design security system, it does not offer guaranteed protection The Following Recommendations for the Location of Fire and Burglary Detection Devices Help against burglary or fire or other emergency. Any alarm system, whether commercial or Provide Proper Coverage for the Protected Premises. residential, is subject to compromise or failure to warn for a variety of reasons. For example: Recommendations for Smoke and Heat Detectors • Intruders may gain access through unprotected openings or have the technical sophistication With regard to the number and placement of smoke/heat detectors, we subscribe to the to bypass an alarm sensor or disconnect an alarm warning device. recommendations contained in the National Fire Protection Association's (NFPA) Standard #72 • Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other noted below. sensing devices will not work without power. Battery-operated devices will not work without Early warning fire detection is best achieved by the installation of fire detection equipment in all batteries, with dead batteries, or if the batteries are not put in properly. Devices powered rooms and areas of the household as follows: For minimum protection a smoke detector solely by AC will not work if their AC power supply is cut off for any reason, however briefly. should be installed outside of each separate sleeping area, and on each additional floor of a • Signals sent by wireless transmitters may be blocked or reflected by metal before they reach multi-floor family living unit, including basements. The installation of smoke detectors in the alarm receiver. Even if the signal path has been recently checked during a weekly test, kitchens, attics (finished or unfinished), or in garages is not normally recommended. blockage can occur if a metal object is moved into the path. For additional protection the NFPA recommends that you install heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and • A user may not be able to reach a panic or emergency button quickly enough. storage rooms, basements and attached garages. • While smoke detectors have played a key role in reducing residential fire deaths in the United In addition, we recommend the following: States, they may not activate or provide early warning for a variety of reasons in as many as • Install a smoke detector inside every bedroom where a smoker sleeps. 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are • Install a smoke detector inside every bedroom where someone sleeps with the door partly as follows. Smoke detectors may have been improperly installed and positioned. Smoke or completely closed. Smoke could be blocked by the closed door. Also, an alarm in the detectors may not sense fires that start where smoke cannot reach the detectors, such as in hallway outside may not wake up the sleeper if the door is closed. chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may • Install a smoke detector inside bedrooms where electrical appliances (such as portable not sense a fire on another level of a residence or building. A second-floor detector, for heaters, air conditioners or humidifiers) are used. example, may not sense a first-floor or basement fire. Moreover, smoke detectors have • Install smoke detectors at both ends if the hallway is more than 40 feet (12 meters) long. sensing limitations. No smoke detector can sense every kind of fire every time. In general, • Install smoke detectors in any room where an alarm control is located, or in any room detectors may not always warn about fires caused by carelessness and safety hazards like where alarm control connections to an AC source or phone lines are made. If detectors smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, are not so located, a fire within the room could prevent the control from reporting a fire or overloaded electrical circuits, children playing with matches, or arson. Depending upon the an intrusion. nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates This Control Complies with NFPA Requirements for Temporal Pulse as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death Sounding of Fire Notification Appliances • Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as Recommendations for Proper Intrusion Protection diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric • For proper intrusion coverage, sensors should be located at every possible point of entry area protection. They do create multiple beams of protection, and intrusion can only be to a home or premises. This would include any skylights that may be present, and the detected in unobstructed areas covered by those beams. They cannot detect motion or upper windows in a multi-level building. intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass • In addition, we recommend that radio backup be used in a security system. This will doors, or windows. Mechanical tampering, masking, painting or spraying of any material on ensure that alarm signals can be sent to the alarm monitoring station in the event that the the mirrors, windows or any part of the optical system can reduce their detection ability. communications are out of order (if connected to an alarm monitoring station). Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90° to 105°F, the detection performance can decrease. KITCHEN BEDROOM BEDROOM TV ROOM KITCHEN DINING BDRM DINING • Alarm warning devices such as sirens, bells, or horns may not alert people or wake up LIVING ROOM sleepers if they are located on the other side of closed or partly open doors. If warning BDRM devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not BEDROOM BEDROOM hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, LIVING ROOM or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing- impaired people or waken deep sleepers. • Telephone lines needed to transmit alarm signals from a premises to a central monitoring Smoke Detectors for Minimum Protection station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. Smoke Detectors for Additional Protection • Even if the system responds to the emergency as intended, however, occupants may have BEDROOM Heat-Activated Detectors insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. TO BEDROOM BR BEDROOM • This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any KTCHN time. GARAGE LVNG RM . CLOSED DOOR The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. BASEMENT floor_plan-001-V1 Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners, and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. Federal Communications Commission & ISED Statements We continue to develop new and improved protection devices. Users of alarm systems owe it to The user shall not make any changes or modifications to the equipment unless authorized by themselves and their loved ones to learn about these developments. the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. RF Exposure CLASS B DIGITAL DEVICE STATEMENT Warning – The antenna(s) used for this device must be installed to provide a separation This equipment has been tested to FCC requirements and has been found acceptable for use. distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating The FCC requires the following statement for your information: in conjunction with any other antenna or transmitter except in accordance with FCC and ISED This equipment generates and uses radio frequency energy and if not installed and used multi-transmitter product procedures. properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with Mise en Garde the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a Exposition aux Frequences Radio: La/les antenne(s) utilisée(s) pour cet émetteur residential installation. However, there is no guarantee that interference will not occur in a doit/doivent être installée(s) à une distance de séparation d'au moins 20 cm (7,8 pouces) de particular installation. If this equipment does cause interference to radio or television reception, toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre transmetteur ou which can be determined by turning the equipment off and on, the user is encouraged to try to antenne, excepté en conformité avec les procédures de produit multi transmetteur FCC et correct the interference by one or more of the following measures: ISEDs. • If using an indoor antenna, have a quality outdoor antenna installed. • Reorient the receiving antenna until interference is reduced or eliminated. This equipment should be installed in accordance with Chapter 2 of the National Fire • Move the radio or television receiver away from the receiver/control. Alarm Code, ANSI/NFPA 72, (National Fire Protection Association, Batterymarch • Move the antenna leads away from any wire runs to the receiver/control. Park, Quincy, MA 02269). Printed information describing proper installation, • Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. operation, testing, maintenance, evacuation planning, and repair service is to be • Consult the dealer or an experienced radio/TV technician for help. provided with this equipment. Warning: Owner’s instruction notice: ’Not to be removed by anyone except occupant ISED CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. WARRANTY INFORMATION FCC / ISED STATEMENT This device complies with Part 15 of the FCC Rules, and ISED’s license-exempt RSSs. For the latest warranty information, please go to: Operation is subject to the following two conditions: (1) This device may not cause harmful www.honeywell.com/security/hsc/resources/wa. interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warranty Patents For patent information, see www.honeywell.com/patents Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS ISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable. ADT Security Services, Inc. 1501 Yamato Road Boca Raton, FL 33431 Copyright © 2018 ADT Security Services


Document Created: 2018-06-06 12:15:02
Document Modified: 2018-06-06 12:15:02
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC