Manual

FCC ID: CCKPC0192

Users Manual

Download: PDF
FCCID_3218077

1115 WIRELESS TEMPERATURE Y SENSOR AND FLOOD DETECTOR Installation Guide R 1 PROGRAM THE PANEL The 1115 Wireless Temperature Sensor and Flood Detector can be programmed with up to four zones. When programming the 1115 in the panel, refer to the panel programming guide as needed. A Note: When a wireless receiver is installed, powered down and powered up, the panel is reset, or programming is complete, the supervision time is reset. If the receiver has been powered down for more than one hour, the 1115 may take up to an additional hour to Figure 1: 1115 Wireless send a supervision message unless tripped, tampered, or powered Temperature Sensor and up. This operation extends battery life. A missing message may Flood Detector display on the keypad until the supervision message is sent. IN 1. In ZONE INFORMATION, enter the ZONE number and press CMD. DESCRIPTION Note: Zones must be entered sequentially. For example, if you begin by programming zone 80, you would need to program The 1115 Wireless Temperature zone 81 as the next contact. Sensor and Flood Detector is 2. Enter the ZONE NAME and press CMD. designed to be used in a variety of applications. The 1115 has an 3. Select SV (Supervisory) as the Zone Type and press CMD. internal temperature sensor that 4. At the NEXT ZONE prompt, select NO. If you see the can be set to detect cold, hot, or warm temperature ranges. WIRELESS ZONE prompt, select YES. M When combined with the 5. Enter the eight-digit SERIAL NUMBER and press CMD. remote T280R temperature 6. Enter the CONTACT number being used. probe, the 1115 can be set to monitor refrigerated or freezing Note: Contacts can be entered in any order. Refer to Table 1 temperatures. to select the correct contact. The 1115 can also be paired with 7. Enter the SUPRVSN TIME and press CMD. the remote 470PB water sensor 8. At the NEXT ZONE prompt, select YES and continue to and used in situations where flood program up to three more zones. LI detection is necessary. Depending on a customer’s needs, the 1115 can be programmed with 2 up to four zones and serve as a temperature sensor, flood detector, or both. INSTALL THE BATTERIES After the transmitter has been programmed into the panel, install the batteries. Use only 3.0V lithium batteries, DMP Model CR123A, or the equivalent battery from a local retail E Compatibility outlet. Keep in mind, when setting up a wireless system, program All DMP 1100 Series Wireless Receivers and burglary zones and connect the receiver before installing batteries in the panels. See the last page for transmitters. compatibility details. 1. Remove the cover by pushing the button on the end of the cover and gently pulling upwards. R 2. Observing polarity, place the battery in the holder and press into place. What is Included? ƒƒ One 1115 PCB mounted in a two‑part housing ƒƒ One 3V lithium CR123A battery ƒƒ One 2M EOL resistor P ƒƒ Mounting screws LT-1547 © 2016 Digital Monitoring Products, Inc. 16462

3 Tamper SELECT A LOCATION Survey Y Switch LED The 1115 provides a survey capability to allow one person to confirm communication with the wireless receiver or panel while the cover is removed. This allows you to easily determine the best location for the 1115. Be sure to choose a location T C F on a flat wall or single-gang box away from large metal objects. R 1. Hold the 1115 in the exact desired location. 2. Press the tamper switch to send data to the receiver and determine if communication is confirmed or faulty. See Figure 2 for tamper switch and LED locations. Confirmed: If communication is confirmed, the survey LED turns on when data is sent to the receiver and off A when acknowledgement is received. Faulty: If communication is faulty, the LED remains on for about 8 seconds or flashes multiple times in quick succession. 3. Relocate the 1115 or receiver until the LED confirms clear communication. Proper communication between the 1115 IN and receiver is verified when for each press or release of the tamper switch, the LED blinks immediately on and immediately off. Figure 2: Tamper Switch and Survey LED 4 SET THE DIP SWITCHES The 1115 has four DIP switches (labeled 1 through 4) located on the PCB. Cold and flood settings can be turned on or off. Hot/warm and freeze/refrigerate are either-or settings. Refer to Table 1 for DIP M switch setting options and operations: DIP SWITCH ALARM OCCURS ZONE RESTORES OPERATION CONTACT SENSOR POSITION WHEN: WHEN: Temperature drops below 45ºF for Temperature rises above 48ºF Cold 1 = ON 1 Internal >10 minutes for > 4 minutes LI Temperature rises above 95ºF for Temperature drops below Hot 2 = OFF 2 Internal > 10 minutes 92ºF for > 4 minutes Temperature rises above 75ºF for Temperature drops below Warm 2 = ON 2 Internal > 10 minutes 72ºF for > 4 minutes Temperature rises above 10°F for Temperature drops below 7°F Freezer 3 = OFF 3 External (T280R) > 30 minutes for > 4 minutes E Temperature rises above 42°F for Temperature drops below Refrigerator 3 = ON 3 External (T280R) > 30 minutes 39°F for > 4 minutes Probe tips are in contact with Probe tips have not been in Flood 4 = ON 4 External (470PB) water for > 3 minutes water for > 3 minutes R Table 1: DIP Switch Settings and Operation P 1115 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 2

5 WIRE THE SENSOR PROBES (Optional) SENSOR PROBES Y If freezer or refrigerator sensing functionality is required, connect a T280R temperature sensor probe. If flood 2M EOL Resistor sensing functionality is required, connect a 470PB water sensor probe. When connecting a remote probe to the terminal Connect to Connect to block, DMP recommends using 18 or 22-gauge unshielded wire. Do Terminal F Terminal C R not use twisted pair or shielded wire. Connect the 470PB Water Sensor Probe To use the 470PB, place the probe inside the area and run 18 or 22-gauge unshielded wire to the 1115. Follow these steps to connect the wire to the 1115 terminals: 1. Connect a wire from the top of one of the sensor’s probes to Figure 3: 470PB Water A the F terminal on the 1115 PCB by running it through the wiring Sensor Probe opening in the housing. See Figures 3 and 5. 2. Connect a wire from the top of the other probe to the C terminal on the 1115 PCB by running it through the wire Connect to Terminal C opening in the housing. 3. Connect a 2M EOL resistor (included with the 1115) between Connect to IN the two probes. Terminal T Connect the T280R Temperature Sensor Probe To use the T280R, place the probe inside the refrigerator or freezer environment and run 18 or 22-gauge unshielded wire to the 1115. Follow these steps to connect the wire to the 1115 terminals: Figure 4: T280R Temperature Sensor Probe 1. Connect the grey wire to the T terminal on the 1115 PCB by running it through the wire opening in the housing. See Figures 4 and 5. 2. Connect the black wire to the C terminal on the 1115 PCB by Wire Opening running it through the wire opening in the housing. M Optional Terminal Block Mounting Hole 6 MOUNT THE 1115 It is recommended the sensor be mounted on a flat wall T C F away from large metal objects. Do not mount the 1115 inside of freezers or walk-in refrigerators. In those situations, use LI the optional remote T280R temperature probe. 1. Hold the transmitter base on the wall and place one screw into the mounting hole location shown in Figure 5 and secure the housing to the surface. Note: You can place an additional screw in the optional mounting hole if needed. 2. Snap the transmitter housing cover back on the base. E R Mounting Hole Figure 5: Mounting Holes and Terminal Block P 1115 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3

REPLACE THE BATTERY Y 1. Remove the cover by pushing the button on the end of the cover and gently pulling upwards. 2. Remove the old battery and dispose of it properly. 3. Observing polarity, place the new battery in the holder and press into place. 4. Snap the transmitter housing cover back on the base. Caution: Properly dispose of used batteries. Do not recharge, disassemble, heat above 212°F (100°C), or incinerate. Risk of fire, explosion, and burns. R Sensor Reset to Clear LOBAT When the battery needs to be replaced, a LOBAT message will display on the keypad. Once the battery is replaced, a sensor reset is required at the system keypad to clear the LOBAT message. 1. On a Thinline keypad, press and hold “2” for two seconds. On a touchscreen keypad press RESET. 2. Enter your user code if required. 3. The keypad displays SENSORS OFF followed by SENSORS ON. A FCC INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all persons. It must not be located or operated in conjunction with any other antenna or transmitter. Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IN Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ƒƒ Reorient or relocate the receiving antenna. ƒƒ Increase the separation between the equipment and receiver. ƒƒ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ƒƒ Consult the dealer or an experienced radio/TV technician for help. M Industry Canada Information This device complies with Industry Canada Licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. this device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits specified by Health Canada Safety Code 6. The system must be installed at a minimum separation distance from the antenna to a general bystander of 7.87 inches (20 cm) LI to maintain compliance with the General Population limits. L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites établies par le Code de sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces (20 cm) séparant l’antenne d’une personne présente en conformité avec les limites permises d’exposition du grand public. Specifications Certifications Battery ƒƒ FCC Part 15 Registration ID CCKPC0192 (pending) Life Expectancy 3 Years (normal operation) ƒƒ Industry Canada Registration ID 5251A-PC0192 (pending) E Type 3.0V Lithium CR123A Frequency Range 905-924 MHz Compatibility ƒƒ 1100X Wireless Receiver version 104 or higher Dimensions 3.3” L x 1.6” W x 1.2” H ƒƒ 1100XH Wireless Receiver version 105 or higher Color White ƒƒ 1100D Wireless Receiver version 104 or higher ƒƒ 1100DI Wireless Receiver Version 105 or higher Housing Material Flame retardant ABS ƒƒ 1100DH Wireless Receiver Version 105 or higher ƒƒ XT50 Series panels with integrated wireless receiver version 101 or higher Accessories ƒƒ XTL Series panels with integrated wireless receiver version 104 or higher R 470PB Water Sensor Probe ƒƒ XTLplus Series Panels T280R Temperature Sensor Probe Patents Replacements ƒƒ U. S. Patent No. 7,239,236 ƒƒ CR123A 3.0V Lithium Battery INTRUSION • FIRE • ACCESS • NETWORKS Designed, engineered, 2500 North Partnership Boulevard and manufactured in P Springfield, Missouri 65803-8877 Springfield, Missouri 800-641-4282 | dmp.com


Document Created: 2016-11-16 11:38:45
Document Modified: 2016-11-16 11:38:45
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC