Users Manual

FCC ID: C5F7NFCST-45BU

Users Manual

Download: PDF
FCCID_2603

FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference User‘s Guide of will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is Generic USB Hub encouraged to try to correct the interference by one or more of the following measures : — Reorient orrelocate the receiving antenna. —Increase the separation between the equipment and receiver. Model : CST—45BU —Connect the equipment to an outlet on a circuit different from that to which the receiveris connected. —Consult the dealer or an experienced radio, TV technician for help. CAUTION: Any changes or modifications not expressly approved by the part responsible for compliance could void the user‘s authority to operate the equipment. Daewoo Electronics Co., Ltd.

The CST—45BU USB Hub gives Installing the Tilt{Swivel Stand you 4 downstream ports for connection to USB—equipped 1. Ensure that the power to the monitoris off. peripherals and 1 upstream port for connection to your PC or 2. Set the monitor face down with the underside facing you. Please workstation USB port, or to be careful so as not to seratch the monitor sercen. another USB slef—powered Hub. 3. Align the four hooks on the stand with the guide holes of bottom chassis Feqiures . of the monitor. 1. 1 upstream and 4 downstream USB ports. 4. Insert the hooks into the guide holes. 2. Bus powered from host controller when using low 5. Slide the tilt/swivel stand toward the front of the monitor until the latch powered USB devices. locks in position. 3. Supports high and low—speed USB—ready peripherals. 6. Turn the monitor and the stand upright. 4. Over—current protection. Em 5. 100% Plug and Play Fully compatible with Windows Device ~_— 95Rev. B and Windows 98. enefits Ease—of—use — single cable type for USB peripherals allows true Plug—n— Play. Easy to add peripherals — USB allows up to 127 devices. Cable management outside your PC is neat and straightforward. mwer is powered from USB host controller. ‘mitation for a bus—powered hub his Hub is a bus—powered hub: that is, it draws electrical current for its eration (500ma) directly from its upstream connection to the USB. If you want to remove the tilt/swivel stand on the monitor, press the latch delivers 100ma of current to each of its four downstream connections and pull the tilt/swivel stand toward the back of the monitor. Lift the stand sing the remaining power forits own operation}. The USB specification to separate. es not perimit the connection of an additional bus—powered hub to one of : downstream portsof a bus—powered hub. his Hub can be mounted as a stand base in Dacwoo 14",15"Monitor 31X,518X,518B).

Technical Descriptif)n of the appafatus Model name : CST—45BU (Generic USB Hub) i. Hub : TUSB2040A (Texas Instruments) 2. Type : Bus Powered, Individual Mode 3. Up—stream : l—port 4. Down—stream : 4—port 5. Over Current Protection : Yes . 6. Supports high and low-:‘sgged USB—ready peripherals 7. Delivers 100mA of current to each of its four downstream connections s. Dimension : 240(W) X 71.6(H) X 442(D)mm 9. Weight (net) : 505g


Document Created: 1998-06-04 18:29:29
Document Modified: 1998-06-04 18:29:29
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC