Test Report

FCC ID: C5F7NF0007

Test Report

Download: PDF
FCCID_180401

ATTACHMENT C – TEST REPORT © 2001 PCTEST Lab

0 PCTEST Engineering Laboratory, Inc. 6660-B Dobbin Road • Columbia, MD 21045 • U.S.A. TEL (410) 290-6652 • FAX (410) 290-6654 http://www.pctestlab.com CERTIFICATION OF COMPLIANCE FCC Class B (Class II Permissive Change) DAEWOO Electronics Co., Ltd. Dates of Tests: October 25-26, 2001 International Standards Research Center Test Report S/N: HID.210927564.C5F 543, Dangjung-Dong, Kunpo-City, Test Site: PCTEST Lab., MD U.S.A. Kyonggi-Do 435-030, KOREA Attn: Mr. H.C. Kim, EMC Engineer FCC ID C5F7NF0007 APPLICANT DAEWOO ELECTRONICS CO., LTD. Rule Part(s): Part 15.115; ANSI C63.4 (1992); MP-3 Equipment Class: Class II Permissive Change EUT Type: Video Cassette Recorder (VHS) Model(s): DV-T8D4N Trade Name(s): DAEWOO RF Frequency Out: 60MHz – 72MHz Tuner Rx Frequency: 54MHz – 806MHz Original Grant Date: February 23, 2001 Class II Change(s): Alternate Tuner Model: SSTMI-US3-S This equipment, with the Class II Permissive Change(s) listed above, has been shown to be capable of continued compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified is ANSI C63.4-1992. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. PCTEST certifies that no party to this application has been denied the FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Lab Code 100431-0 © 2001 PCTEST Engineering Lab., Inc.

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change TABLE OF CONTENTS ATTACHMENT A: COVER LETTER(S) ATTACHMENT B: ATTESTATION STATEMENT(S) ATTACHMENT C: TEST REPORT SCOPE 1 INTRODUCTION (SITE DESCRIPTION) 2 PRODUCTION INFORMATION 3 DESCRIPTION OF TESTS 4-6 A. CONDUCTED EMISSIONS B. RADIATED EMISSIONS C. OUTPUT TERMINAL SIGNAL LEVEL MEASUREMENTS D. OUTPUT TERMINAL CONDUCTED SPURIOUS EMISSION E. TRANSFER SWITCH ISOLATION MEASUREMENTS LIST OF SUPPORT EQUIPMENT 7 TEST DATA (CONDUCTED) 8 TEST DATA (RADIATED) 9 TEST DATA (OUTPUT TERMINAL SIGNAL) 10 TEST DATA (OUTPUT TERMINAL ) 11 TEST DATA (TRANSFER SWITCH ISOLATION) 11 PLOTS OF EMISSIONS 12 ACCURACY OF MEASUREMENT 13 LIST OF TEST EQUIPMENT 14 TEST SOFTWARE USED 15 CONCLUSION 16 ATTACHMENT D: TEST PLOTS ATTACHMENT E: PHOTOGRAPHS of TEST SET-UP ATTACHMENT F: EXTERNAL EUT PHOTOGRAPHS ATTACHMENT G: INTERNAL EUT PHOTOTGRAPHS ATTACHMENT H: FCC ID LABEL & LOCATION ATTACHMENT I: COPY OF FCC GRANT © 2001 PCTEST Engineering Laboratory, Inc. FCC Part 15.115

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change PRODUCT EVALUATION REPORT Scope - Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission. Company Name: DAEWOO ELECTRONICS CO., LTD. Address: International Standards Research Center 543, Dangjung-Dong, Kunpo-City, Kyonggi-Do 435-030, KOREA Attention: Seung Deug, Park – Chief of Technical Planning Team • FCC ID: C5F7NF0007 • Classification: Class II Permissive Change • EUT Type: Video Cassette Recorder (VHS) • Models: DV-T8D4N • FCC Rule Part(s): § 15.115 • Test Procedure(s): MP-3; ANSI C63.4 (1992) • RF Freq. Range: 60 – 72 MHz • RF Channels: Ch. 3 / Ch. 4 • Dates of Tests: October 25-26, 2001 • Place of Tests: PCTEST Lab, Columbia, MD U.S.A. • Test Report S/N: HID.210927564.C5F • Original Grant Date: February 23, 2001 • Class II Change(s): Alternate Tuner Model: SSTMI-US3-S NOTE: The tuners (TV receivers) were tested under the verification procedure and complied with Section 15.115 of the FCC rules. Lab Code 100431-0 © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 1 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change INTRODUCTION The measurement procedure described in MP-3, entitled “FCC Methods of Measurements of Output Signal Level, Output Terminal Conducted Spurious Emissions, Transfer Switch Characteristics, and Radio Noise Emissions from TV interface Devices,” and ANSI C63.4-1992 were used in determining EME emanating from DAEWOO Electronics Co., Ltd. Video Cassette Recorder FCC ID: C5F7NF0007. These measurement tests were conducted at PCTEST Engineering Laboratory, Inc. facility in New Concept Business Park, Guilford Industrial Park, Columbia, Maryland. The site address is 6660-B Dobbin Road, Columbia, MD 21045. The test site is one of the highest points in the Columbia area, with an elevation of 390 feet above mean sea level. The site coordinates are 39° 11'17” N latitude and 76° 49'38" W longitude. The facility is 1.5 miles North of the FCC laboratory, and the ambient signal and ambient signal strength are approximately equal to those of the FCC laboratory. There are no FM or TV transmitters within 15 miles of the site. The detailed description of the measurement facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4 on October 19, 1992. PCTEST Location The map at right shows the location of the PCTEST Lab, its proximity to the FCC Lab, the Columbia vicinity area, the Baltimore-Washington International (BWI) airport, and the city of Baltimore, and the Washington, D.C. area. (see Figure1). Figure 1. Map of the Greater Baltimore and Metropolitan Washington, D.C. area. © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 2 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change Product Information Equipment Description The Equipment Under Test (EUT) is the DAEWOO Electronics Co., Ltd. (Models: DV-T8D4N) 4-head VHS Video Cassette Recorders FCC ID: C5F7NF0007. RF Frequency Out: 60MHz – 72MHz Tuning Frequency: 54MHz – 806MHz Format: VHS Standard Video Signal: EIA Standard NTSC Color Scanning System: Rotary, double azimuth, four-head helical scanning system RF Impedance: 75 Ω RF Output Signal: Channel 3 or Channel 4 (switch selectable) Power Cord: Unshielded Cable(s): Unshielded Power Requirement: AC 120V / 60Hz Power Consumption: 17 W Dimensions (WxHxD): 360 x 91 x 238 mm Weight (Net): 2.9 Kg © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 3 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change Description of Tests Conducted Emissions The line-conducted facility is located inside a 16'x20'x10' shielded enclosure. It is manufactured by Ray Proof Series 81 (see Figure 2). Figure 2. Shielded Enclosure Line-Conducted Test Facility The shielding effectiveness of the shielded room is in accordance with MIL-Std-285 or NSA 65-6. A 1m. x 1.5m. wooden table 80cm. high is placed 40cm. away from the vertical wall and 1.5m away from the side wall of the shielded room (see Figure 3). Solar Electronics and EMCO Model 3725/2 (10kHz-30MHz) 50Ω/50µH Line-Impedance Stabilization Networks (LISNs) are bonded to the shielded room (see Figure 4). The EUT is powered from the Solar LISN and the support equipment is powered from the EMCO LISN. Power to the LISNs are filtered by a high-current high-insertion loss Ray Proof power line filters (100dB 14kHz-10GHz). The purpose of the filter is to attenuate ambient signal interference and this filter is also bonded to the Figure 3. Line Conducted shielded enclosure. All electrical cables are shielded by braided Emission Test Set-Up tinned copper zipper tubing with an inner diameter of 1/2". If the EUT is a DC-powered device, power will be derived from the source power supply it normally will be powered from, and the supply lines will be connected to the Solar LISN. LISN schematic diagram is shown in Figure 5. All interconnecting cables more than 1 meter were shortened by non-inductive bundling (serpentine fashion) to a 1-meter length. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The RF output of the LISN was connected to the spectrum Figure 4. Wooden Table & analyzer to determine the frequency producing the maximum EME Bonded LISNs from the EUT. The spectrum was scanned from 450kHz to 30MHz with 20 msec. sweep time. The frequency producing the maximum level was reexamined using EMI/ Field Intensity Meter and Quasi-Peak adapter. The detector function was set to CISPR quasi-peak mode. The bandwidth of the receiver was set to 10 kHz. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each EME emission. Each emission was maximized by: switching power lines; varying the mode of operation or resolution; clock or data exchange speed; scrolling H pattern to the EUT and/or support equipment, and powering the monitor from the floor mounted outlet box and the computer aux AC outlet, if applicable; whichever determined the worst-case emission. Photographs of the worst-case emission can be seen in Attachment H. Each EME reported was calibrated using the HP8640B signal generator. Figure 5. LISN Schematic Diagram © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 4 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change Radiated Emissions Preliminary measurements were made indoors at 1 meter using broadband antennas, broadband amplifier, and spectrum analyzer to determine the frequency producing the maximum EME. Appropriate precaution was taken to ensure that all EME from the EUT were maximized and investigated. The system configuration, clock speed, mode of operation or video resolution, turntable azimuth with respect to the antenna were noted for each frequency found. The spectrum was Figure 6. 3-Meter Test Site scanned from 30 to 200 MHz using biconical antenna and from 200 to 1000 MHz using log-spiral antenna. Above 1 GHz, linearly polarized double ridge horn antennas were used. Final measurements were made outdoors at 3-meter test range using Roberts Dipole antennas or horn antenna (see Figure 6). The test equipment was placed on a wooden and plastic bench situated on a 1.5 x 2 meter area adjacent to the measurement area (see Figure 7). Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. Each frequency found during pre-scan measurements was re-examined and investigated using EMI/Field Intensity Meter and Quasi-Peak Adapter. The Figure 7. Dimensions of detector function was set to CISPR quasi-peak mode and the bandwidth of Outdoor Test Site the receiver was set to 100kHz or 1 MHz depending on the frequency or type of signal. The half-wave dipole antenna was tuned to the frequency found during preliminary radiated measurements. The EUT, support equipment and interconnecting cables were re-configured to the set-up producing the maximum emission for the frequency and were placed on top of a 0.8- meter high non-metallic 1 x 1.5 meter table (see Figure 8). The EUT, support equipment, and interconnecting cables were re-arranged and manipulated to maximize each EME emission. The turntable containing the system was rotated; the antenna height was varied 1 to 4 meters and stopped at the azimuth or height producing the maximum emission. Each Figure 8. Turntable and emission was maximized by: varying the mode of operation or resolution; System Setup clock or data exchange speed; scrolling H pattern to the EUT and/or support equipment; powering the monitor from the floor mounted outlet box and the computer aux AC outlet if applicable, and changing the polarity of the antenna; whichever determined the worst-case emission. Photographs of the worst-case emission can be seen in Attachment H. Each EME reported was calibrated using the HP8640B signal generator. The Theoretical Normalized Site Attenuation Curves for both horizontal and vertical polarization are shown in Figure 9. Figure 9. Normalized Site Attenuation Curves (H&V) © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 5 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change Output Signal Level Measurements The RF output of the TV interface device was fed to the TV receiver via coaxial cable. The signal level was measured by direct connection to the spectrum analyzer with 50/75 ohm matching transformer between the spectrum analyzer and the TV interface device. The RF output signal level measured RMS voltage was the highest RF level present at the output terminals during normal use of the device. Measurements were made of the levels of both the visual (61.25 MHz) and aural (71.75 MHz) of TV channel 4. The voltage corresponding to the peak envelope power of the video modulated signal during maximum amplitude peaks across a resistance (R ohms) matching the rated output impedance of the device, must not exceed 692.8 R1/2 uV for all other TV interface device. The voltage corresponding to peak envelope power of the audio modulated signal, if provided by the TV interface device, must not exceed 155R1/2 uV for cable system terminal device of TV interface device used with a master antenna, and 77.5 R1/2 uV for all other TV interface device. Output Terminal Conducted Spurious Emission The RF output signal was fed to the TV receiver via coaxial cable. Measurements were made by direct connection to the spectrum analyzer and TV interface device with 50/75 ohm matching transformer. The frequency range 30 to 1000 MHz was investigated for significant emission. The maximum RMS voltage of any emission appearing on frequencies removed by more than 4.6 MHz below or 7.4 MHz above the video carrier frequency on which the TV interface device is operated must not exceed 692.8 R1/2 uV for cable system terminal device or TV interface device used with a master antenna and 1.95 R1/2 uV for all other TV interface device when terminated with a resistance (R ohms) matching the rated output impedance of the TV interface device. Transfer Switch Isolation Measurement Measurements were made of the maximum RMS voltage at the antenna input terminals of the switch for all positions of the transfer switch. The maximum voltage corresponds to the peak envelope power of the video signal during maximum amplitude peaks. In either position of the receiver transfer switch, the maximum voltage at the receiving antenna input terminals of the switch when terminated with a resistance (R ohms) matching the rated impedance of the antenna input of the switch, must not exceed 0.346 R1/2 uV. The maximum voltage corresponds to the peak envelope power of the video modulated signal during maximum amplitude. Each EME reported was calibrated using HP8640B signal generator and is listed on Table 4. © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 6 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change Support Equipment Used 1. DAEWOO VCR (EUT) FCC ID: C5F7NF0007 w/SSTMI-US3-S Tuner 1.6 m. unshielded AC power cord 1.0 m. unshielded RCA Stereo A/V cable (x3) 1.2 m. shielded RF cable 2. CANOVISION 8 Video Camera Model: H660A S/N: 880001281 1.8 m. unshielded AC power cable 1.5 m. unshielded DC power cord 3. DAEWOO Television Model: A13P02D S/N: 4855415800 1.8 m. unshielded AC power cord 4. LEADER NTSC Pattern Model No: 408 S/N: 0377433 Signal Generator 1.8 m. unshielded AC power cord 1.5 m. shielded BNC cables (Please see “Attachment F - Test Setup Photographs” for actual system test setup.) © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 7 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change LINE-CONDUCTED TEST DATA Conducted Emissions (See Data under PLOTS – Attachment D) NOTES: 1. All modes of operation were investigated, and the worst-case emissions are reported. 2. All other emissions are non-significant. The EUT was tested with the EUT plugged into the LISN. 3. AC powerline conducted measurements were made with the VCR input in the play mode, record mode with 1 volt peak-to-peak VITS input, and record mode with 5 volts peak-to-peak VITS input on both Channels 3 & 4. 4. µV from 450kHz to 30MHz (see Figure 11 – page 16). The limit for Class B device is 250µ 5. Line A = Phase; Line B = Neutral 6. Deviations to the Specifications: None * All readings are calibrated by HP8640B signal generator with accuracy traceable to the National Institute of Standards and Technology (formerly NBS). ** Measurements using CISPR quasi-peak mode. © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 8 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change Radiated Test Data Radiated Emissions FREQ. Level* AFCL** POL Height Azimuth F/S Margin*** (MHz) (dBm) (dB) (H/V) (m) (° angle) (µV/m) (dB) 343.63 - 94.08 22.08 V 1.2 180 56.28 - 11.0 225.67 - 88.68 17.68 H 1.4 145 63.15 - 10.0 200.45 - 91.52 16.52 H 1.6 190 39.86 - 11.5 190.13 - 88.70 16.01 H 2.0 170 51.93 - 9.2 153.93 - 85.27 13.88 H 2.5 180 60.31 - 7.9 139.61 - 84.16 12.97 V 2.7 200 61.71 - 7.7 Table 1. Radiated Measurements at 3-meters. NOTES: 1. All modes of operation and video display were investigated. The RF modulator was switched to Channels 3 & 4 and the worst-case emissions are reported. 2. The radiated limits are shown on Figure 12 (Page 16). Above 1GHz the limit is 500 µV/m. 3. Radiated measurements were made with the VCR input in the play mode, record mode with 1 volt peak-to-peak VITS input and record mode with 5 volts peak-to-peak VITS input on both Channels 3 & 4. * All readings are calibrated by HP8640B signal generator with accuracy traceable to the National Institute of Standards and Technology (formerly NBS). ** AFCL = Antenna Factor (Roberts dipole) and Cable Loss (30 ft. RG58C/U). *** Measurements using CISPR quasi-peak mode. Above 1GHz, peak detector function mode is used using a resolution bandwidth of 1MHz and a video bandwidth of 1MHz. The peak level complies with the average limit. Peak mode is used with linearly polarized horn antenna and low-loss microwave cable. © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 9 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change Test Data Output Terminal Signal Measurements* TV CH. Freq. (MHz) Level (dBm) Limit (dBm) Margin (dB) 3 (Pix) 61.25 - 41.8 - 37.46 - 4.34 3 (Aud) 65.75 - 57.5 - 50.46 - 7.04 4 (Pix) 67.25 - 41.3 - 37.46 - 3.84 4 (Aud) 71.75 - 57.0 - 50.46 - 6.54 Table 2. Output Signal Tabulated Data NOTES: 1. Output Level measurements were made with the VCR in the play mode, record mode with 1 volt peak-to-peak VITS input, and record mode with 5 volts peak-to-peak VITS input on both Channels 3 & 4. 2. All modes of operation were investigated and the worst case emissions are reported. * Pix – Video Modulated Signal Aud – Sound Modulated Signal © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 10 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change Test Data Output Terminal Conducted Spurious Emission No significant emission was observed from 30 – 1000 MHz (See Attached Plots – Attachment D). Transfer Switch Isolation Measurements TV Ch. Freq. (MHz) Level (dBm) Limit (dBm) Margin (dB) 3 61.25 - 101.5 - 97.47 - 4.04 4 67.25 - 101.0 - 97.47 - 3.53 Table 3. Transfer Switch Tabulated Data NOTES: 1. Transfer switch isolation measurements were made on the Channel 3 or 4 video output frequency of 61.25 or 67.25MHz and both positions of the transfer switch were checked for compliance. No significant emissions were found (see attached Plots – Attachment D). 2. Transfer switch isolation measurements were made with the VCR in the play mode, record mode with 1 volt peak-to- peak VITS input and record mode with 5 volts peak-to-peak VITS input on both Channels 3 & 4. 3. The transfer switch is internal to the device that is accessed automatically. 4. The transfer isolation switch provides automatic selection of either antenna/TV or input/game. 5. All modes of operation were investigated and the worst case emissions are reported. © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 11 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change Plot(s) of Emissions (SEE “ATTACHMENT D – TEST PLOTS”) Fig. 11. Line-Conducted Limits Fig. 12. FCC Class B Radiated Limits at 3 meters © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 12 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change Accuracy of Measurement Measurement Uncertainty Calculations: The measurement uncertainties stated were calculated in accordance with the requirements of NIST Technical Note 1297 and NIS 81 (1994). Contribution Probability Uncertainty (± dB) (Line Conducted) Distribution 9kHz-150MHz 150-30MHz Receiver specification Rectangular 1.5 1.5 LISN coupling specification Rectangular 1.5 1.5 Cable and input attenuator calibration Normal (k=2) 0.3 0.5 Mismatch: Receiver VRC Γ1 = 0.03 LISN VRC ΓR = 0.8 (9kHz) 0.2 (30MHz) U-Shaped 0.2 0.35 Uncertainty limits 20Log(1 ± Γ1 ΓR) System repeatability Std. deviation 0.2 0.05 Repeatability of EUT - - Combined standard uncertainty Normal 1.26 1.30 Expanded uncertainty Normal (k=2) 2.5 2.6 Calculations for 150kHz to 30MHz: m 1.52 + 1.52 0.5 uc(y) = ∑ ui2 ( y ) = ± i =1 3 + ( )2 + 0.35 = ±1.298dB 2 U = 2Uc(y) = ±2.6dB Contribution Probability Uncertainties (± dB) (Radiated Emissions) Distribution 3m 10 m Ambient Signals - - Antenna factor calibration Normal (k=2) ± 1.0 ± 1.0 Cable loss calibration Normal (k=2) ± 0.5 ± 0.5 Receiver specification Rectangular ± 1.5 ±1.5 Antenna directivity Rectangular + 0.5 / - 0 + 0.5 Antenna factor variation with height Rectangular ± 2.0 ± 0.5 Antenna phase centre variation Rectangular 0.0 ± 0.2 Antenna factor frequency interpolation Rectangular ±. 0.25 ± 0.25 Measurement distance variation Rectangular ± 0.6 ± 0.4 Site imperfections Rectangular ± 2.0 ± 2.0 Mismatch: Receiver VRC Γ1 = 0.2 + 1.1 Antenna VRC ΓR = 0.67 (Bi) 0.3 (Lp) U-Shaped ± 0.5 - 1.25 Uncertainty limits 20Log(1 ± Γ1 ΓR) System repeatability Std. Deviation ± 0.5 ± 0.5 Repeatability of EUT - - Combined standard uncertainty Normal + 2.19 / - 2.21 + 1.74 / - 1.72 Expanded uncertainty U Normal (k=2) + 4.38 / - 4.42 + 3.48 / - 3.44 Calculations for 3m biconical antenna. Coverage factor of k=2 will ensure that the level of confidence will be approximately 95%, therefore: U=2uc(y) = 2 x ±2.19 = ±4.38 dB © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 13 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change Test Equipment Type Model Cal. Due Date S/N Microwave Spectrum Analyzer HP 8566B (100Hz-22GHz) 12/05/01 3638A08713 Microwave Spectrum Analyzer HP 8566B (100Hz-22GHz) 04/17/02 2542A11898 Spectrum Analyzer/Tracking Gen. HP 8591A (9kHz-1.8GHz) 06/02/02 3144A02458 Spectrum Analyzer HP 8591A (9kHz-1.8GHz) 10/15/02 3108A02053 Spectrum Analyzer HP 8594A (9kHz-2.9GHz) 11/02/02 3051A00187 Signal Generator* HP 8640B (500Hz-1GHz) 06/02/02 2232A19558 Signal Generator* HP 8640B (500Hz-1GHz) 06/02/02 1851A09816 Signal Generator* Rohde & Schwarz (0.1-1000MHz) 09/11/02 894215/012 Ailtech/Eaton Receiver NM 37/57A-SL (30-1000MHz) 04/12/02 0792-03271 Ailtech/Eaton Receiver NM 37/57A (30-1000MHz) 03/11/02 0805-03334 Ailtech/Eaton Receiver NM 17/27A (0.1-32MHz) 09/17/02 0608-03241 Quasi-Peak Adapter HP 85650A 08/09/02 2043A00301 Ailtech/Eaton Adapter CCA-7 CISPR/ANSI QP Adapter 03/11/02 0194-04082 RG58 Coax Test Cable No. 167 n/a Harmonic/Flicker Test System HP 6841A (IEC 555-2/3) 3531A00115 Broadband Amplifier (2) HP 8447D 1145A00470, 1937A03348 Broadband Amplifier HP 8447F 2443A03784 Transient Limiter HP 11947A (9kHz-200MHz) 2820A00300 Horn Antenna EMCO Model 3115 (1-18GHz) 9704-5182 Horn Antenna EMCO Model 3115 (1-18GHz) 9205-3874 Horn Antenna EMCO Model 3116 (18-40GHz) 9203-2178 Biconical Antenna (4) Eaton 94455/Eaton 94455-1/Singer 94455-1/Compliance Design 1295, 1332, 0355 Log-Spiral Antenna (3) Ailtech/Eaton 93490-1 0608, 1103, 1104 Roberts Dipoles Compliance Design (1 set) A100 5118 Ailtech Dipoles DM-105A (1 set) 33448-111 EMCO LISN (2) 3816/2 1077, 1079 EMCO LISN 3725/2 2009 Microwave Preamplifier 40dB Gain HP 83017A (0.5-26.5GHz) 3123A00181 Microwave Cables MicroCoax (1.0-26.5GHz) Ailtech/Eaton Receiver NM37/57A-SL 0792-03271 Spectrum Analyzer HP 8591A 3034A01395 Modulation Analyzer HP 8901A 2432A03467 NTSC Pattern Generator Leader 408 0377433 Noise Figure Meter HP 8970B 3106A02189 Noise Figure Meter Ailtech 7510 TE31700 Noise Generator Ailtech 7010 1473 Microwave Survey Meter Holaday Model 1501 (2.450GHz) 80931 Digital Thermometer Extech Instruments 421305 426966 Attenuator HP 8495A (0-70dB) DC-4GHz Bi-Directional Coax Coupler Narda 3020A (50-1000MHz) Shielded Screen Room RF Lindgren Model 26-2/2-0 6710 (PCT270) Shielded Semi-Anechoic Chamber Ray Proof Model S81 R2437 (PCT278) Environmental Chamber Associated Systems Model 1025 (Temperature/Humidity) PCT285 * Calibration traceable to the National Institute of Standards and Technology (NIST). © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 14 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change Test Software Used TV/Video tape program used: 1. FCC Procedures NOTE: This is a sample of the basic program used during the test. However, during testing, a different software program may be used; whichever determines the worst-case condition. In addition, the program used also depends on the number and type of devices being tested. © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 15 VHS Video Cassette Player

Test Report S/N: HID.210927564.C5F FCC Class 15.115 Dates of Tests: October 25-26, 2001 Class II Permissive Change Conclusion The data collected shows that the DAEWOO Electronics Co., Ltd. VHS Video Cassette Recorder FCC ID: C5F7NF0007 with the Class II Permissive Change(s) described herein complies with Part 15.115 and the TV Interface Device section of the FCC Rules. © 2001 PCTEST Lab DAEWOO FCC ID: C5F7NF0007 16 VHS Video Cassette Player


Document Created: 2001-11-19 15:54:46
Document Modified: 2001-11-19 15:54:46
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC