Dipole cal certs

FCC ID: C3K1793

RF Exposure Info

Download: PDF
FCCID_3611212

Calibration Laboratory of NUz S Schweizerischer Kalibrierdienst Schmid & Partner m‘\ wA Service suisse d‘étalonnage Engineering AG C Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 4/fi\“\ S gwiss Calibration Service thilabs® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client Microsoft Certificate No: D2450V2—917_Apr17 CALIBRATION CERTIFICATE Object D2450V2 — SN: 917 Calibration procedure(s} QA CAL—O05.v9 Calibration procedure for dipole validation kits above 700 MHz Calibration date: April 21, 2017 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for callbration) Primary Standards | ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—17 (No. 217—02521/02522) Apr—18 Power sensor NRP—Z91 SN: 103244 04—Apr—17 (No. 217—02521) Apr—18 Power sensor NRP—Z91 SN: 103245 04—Apr—17 (No. 217—02522) Apr—18 Reference 20 dB Attenuator SN: 5058 (20k) 07—Apr—17 (No. 217—02528) Apr—18 Type—N mismatch combination SN: 5047.2 / 06327 07—Apr—17 (No. 217—02529) Apr—18 Reference Probe EX3DV4 SN: 7349 31—Dec—16 (No. EX3—7349_Dec16) Dec—17 DAE4 SN: 601 28—Mar—17 (No. DAE4—601_Mar17) Mar—18 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: US37202783 07—Oct—15 (in house check Oct—16) in house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) In house check: Oct—18 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Oct—16) In house check: Oct—18 Network Analyzer HP 8753E SN: US37390585 18—Oct—01 (in house check Oct—16) In house check: Oct—17 Name Function Signature Calibrated by: Michael Weber Laboratory Technician I&r Approved by: KatJa Pokovic Technical Manager 4_’ Issued: April 21, 2017 L This calibration certificate shall not be reproduced except in full without written approval of the laboratory. maainccal aiol maamavin mase k }~

Calibration . Laboratory of 3\‘Uz \GZ/z g Schweizerischer Kalibrierdienst Schmid & Partner % c Service suisse d‘étalonnage Engineering AG T//:\\[ Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland */I//\\‘\\s‘ S swiss Calibration Service alutabs Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) 1EC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. * SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%.

Measurement Conditions DASY system contfiguration, as far as not given on page 1. DASY Version DASY5 V52.10.0 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2450 MHz +1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 37.7 16 % 1.87 mho/m + 6 % Head TSL temperature change during test <0.5 °C ~— ——— SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 13.3 W/kg SAR for nominal Head TSL parameters normalized to 1W 51.8 Wikg + 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 6.16 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.2 Wikg £ 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 52.5 +6 % 2.03 mho/m x 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 12.9 W/kg SAR for nominal Body TSL parameters normalized to 1W 50.6 W/kg + 17.0 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 250 mW input power 6.02 Wikg SAR for nominal Body TSL parameters normalized to 1W 23.8 Wikg + 16.5 % (k=2)

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 57.3 Q + 2.7 jQ Return Loss — 22.8 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 52.1 Q + 4.0 jQ Return Loss —27.2 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.157 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on December 19, 2012

DASY5 Validation Report for Head TSL Date: 21.04.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 917 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 1.87 $/m; &, = 37.7; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C€63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(7.72, 7.72, 7.72); Calibrated: 31.12.2016; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 * DASY52 52.10.0(1442); SEMCAD X 14.6.10(7413) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 112.4 V/m; Power Drift =—0.03 dB Peak SAR (extrapolated) = 27.2 W/kg SAR(I g) = 13.3 W/kg; SAR(10 g) = 6.16 W/kg Maximum value of SAR (measured) = 21.3 W/kg dB 0 —5.00 ~10.00 —15.00 —20.00 —25.00 0 dB = 21.3 W/kg = 13.28 dBW/kg

Impedance Measurement Plot for Head TSL 24 Apr 2017 11:50156 (CHZ) S11 1 U FS 4:87.324 e 26543 a 172.43 pH 2 450.000 000 MHz Del Ca fvg 16 HILd CH2 Ca Aw 16° H1d START 2 250,000 000 MHz STOP 2 650.000 000 MHz

DASY5 Validation Report for Body TSL Date: 21.04.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 917 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 2.03 S/m; s = 52.5; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(7.79, 7.79, 7.79); Calibrated: 31.12.2016; Sensor—Surface: 1.4mm (Mechanical Surface Detection) Electronics: DAE4 Sn601; Calibrated: 28.03.2017 Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 DASY52 52.10.0(1442); SEMCAD X 14.6.10(7413) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 103.3 V/m; Power Drift = —0.05 dB Peak SAR (extrapolated) = 25.3 W/kg SAR(I g) = 12.9 W/kg; SAR(10 g) = 6.02 W/kg Maximum value of SAR (measured) = 20.0 W/kg dB 0 —5.00 ~10.00 —15.00 —20.00 —25.00 0 dB = 20.0 W/kg = 13.01 dBW/kg

Impedance Measurement Plot for Body TSL 21 Apr 2017 11:S0:02 CBZ) si1 1 U FS$ 1: 52.105 a 3.9609 e 257.91 pH 2 450.000 @00 MHz w “-—T‘\-\ Del Ca five 16 H1d START 2 250.000 000 MHz STOP 2 650.000 008 MHz

Calibration Laboratory of ly S Schweizerischer Kalibrierdienst 7 Schmid & Partner y p Cc Service suisse d‘étalonnage $ Engineering AG Lz e Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Hi(y S Swiss Calibration Service ues Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Microsoft Certificate No: D5GHzV2—1159_Apr17 |CALIBRATION CERTIFICATE l Object D5SGHzV2 — SN: 1159 Calibration procedure(s) QA CAL—22.v2 Calibration procedure for dipole validation kits between 3—6 GHz Calibration date: April 25, 2017 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1) The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards | ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—17 (No. 217—02521/02522) Apr—18 Power sensor NRP—Z91 SN: 103244 04—Apr—17 (No. 217—02521) Apr—18 Power sensor NRP—291 SN: 103245 04—Apr—17 (No. 217—02522) Apr—18 Reference 20 dB Attenuator SN: 5058 (20k) 07—Apr—17 (No. 217—02528) Apr—18 Type—N mismaich combination SN: 5047.2 / 06327 07—Apr—17 (No. 217—02529) Apr—18 Reference Probe EX3DV4 SN: 3503 31—Dec—16 (No. EX3—3503_Dec16) Dec—17 DAE4 SN: 601 28—Mar—17 (No. DAE4—601_Mar17) Mar—18 Secondary Standards JID # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (in house check Oct—16) in house check: Oct—18 Power sensor HP 8481A SN: US37292783 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) In house check: Oct—18 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Oct—16) in house check: Oct—18 Network Analyzer HP 8753E SN: US37390585 18—Oct—01 (in house check Oct—16) In house check: Oct—17 Name Function Signature Calibrated by: Michael Weber Laboratory Technician ”M_ Approved by: Katia Pokovic Technical Manager m Issued: April 25, 2017 [Thns calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D5GHzV2—1159_Apr17 Page 1 of 13

Calibration ‘ Laboratory of willy‘s/,,’ e S Schweizerischer Kalibrierdienst Schmid & Partner ;E%& c Service suisse d‘étalonnage Engineerlng AG T //:\\ s Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 7'/,,,fi\‘y} S swiss Calibration Service rhiba®s Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y.z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 c) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. * SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D5GHzV2—1159_Apr17 Page 2 of 13

Measurement Conditions DASY system configuration, as far as not iven on page 1. DASY Version DASY5 V52.10.0 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center— TSL 10 mm with Spacer Zoom Scan Resolution dx, dy = 4.0 mm, dz =1.4 mm Graded Ratio = 1.4 (Z direction) 5250 MHz + 1 MHz Frequency 5600 MHz + 1 MHz 5750 MHz + 1 MHz Head TSL parameters at 5250 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.71 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 34.6 16 % 4.52 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5250 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 7.81 Wikg SAR for nominal Head TSL parameters normalized to 1W 774 Wikg £ 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.24 Wikg SAR for nominal Head TSL parameters normalized to 1W 22.1 Wikg #19.5 % (k=2) Certificate No: D5GHzV2—1159_Apr17 Page 3 of 13

Head TSL parameters at 5600 MHz The followingparameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 34.2 16 % 4.86 mho/m + 6 % Head TSL temperature change during test <0.5 °C ~—— SAR result with Head TSL at 5600 MHz SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR measured 100 mW input power 8.10 Wikg SAR for nominal Head TSL parameters normalized to 1W 80.2 W / kg + 19.9 % (k=2) SAR averaged over 10 cm‘ (10 g) of Head TSL condition SAR measured 100 mW input power 2.32 W/kg SAR for nominal Head TSL parameters normalized to 1W 22.9 Wikg + 19.5 % (k=2) Head TSL parameters at 5750 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.4 5.22 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 33.9 +6 % 5.06 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5750 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 7.84 W/kg SAR for nominal Head TSL parameters normalized to 1W 77.6 Wikg 2 19.9 % (k=2) SAR averaged over 10 cm‘ (10 g) of Head TSL condition SAR measured 100 mW input power 2.23 Wikg SAR for nominal Head TSL parameters normalized to 1W 22.0 Wikg £ 19.5 % (k=2) Certificate No: D5GHzV2—1159_Apr17 Page 4 of 13

Body TSL parameters at 5250 MHz The followingparameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.36 mho/m Measured Body TSL parameters (22.0 # 0.2) °C 47.7 £6 % 5.50 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5250 MHz SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 7.68 W/kg SAR for nominal Body TSL parameters normalized to 1W 76.5 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.14 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.3 Wikg £ 19.5 % (k=2) Body TSL parameters at 5600 MHz The followingparameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 47.0 £ 6 % 5.97 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 8.02 W/kg SAR for nominal Body TSL parameters normalized to 1W 79.8 Wikg £ 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.25 Wikg SAR for nominal Body TSL parameters normalized to 1W 22.3 Wikg £ 19.5 % (k=2) Certificate No: D5GHzV2—1159_Apri7 Page 5 of 13

Body TSL parameters at 5750 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.3 5.94 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.8 +6 % 6.18 mho/m 6% Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5750 MHz SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 7.73 W/kg SAR for nominal Body TSL parameters normalized to 1W 76.9 W/kg £ 19.9 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 100 mW input power 215 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.4 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1159_Apr17 Page 6 of 13

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL at 5250 MHz Impedance, transformed to feed point 47.7 Q — 6.5 jQ Return Loss — 23.0 dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 52.2 Q — 1.3 jQ Return Loss — 32.0 dB Antenna Parameters with Head TSL at 5750 MHz impedance, transformed to feed point 53.0 Q — 2.9 jQ Return Loss —27.9 dB Antenna Parameters with Body TSL at 5250 MHz Impedance, transformed to feed point 47.7 Q — 5.3 jQ Return Loss — 24.6 dB Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 53.7 Q + 1.6 jQ Return Loss —28.1 dB Antenna Parameters with Body TSL at 5750 MHz Impedance, transformed to feed point 53.3 Q — 0.9 jQ Return Loss — 29.6 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.201 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole tength is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on June 06, 2013 Certificate No: D5GHzV2—1159_Apr17 Page 7 of 13

DASY5 Validation Report for Head TSL Date: 25.04.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole D5GHzV2; Type: DSGHzV2; Serial: D5GHzV2 — SN: 1159 Communication System: UID 0 — CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz Medium parameters used: f = 5250 MHz; 0 = 4.52 $/m:; & = 34.6; p = 1000 kg/m‘, Medium parameters used: f = 5600 MHz; 0 = 4.86 S/m; & = 34.2; p = 1000 kg/m? , Medium parameters used: f = 5750 MHz; 0 = 5.06 S/m; & = 33.9; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN3503; ConvF(5.58, 5.58, 5.58); Calibrated: 31.12.2016, ConvF(5.09, 5.09, 5.09); Calibrated: 31.12.2016, ConvF(5.02, 5.02, 5.02); Calibrated: 31.12.2016; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 28.03.2017 *« Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 «_ DASY52 52.10.0(1442); SEMCAD X 14.6.10(7413) Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5250 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0; Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 71.48 V/m; Power Drift = —0.05 dB Peak SAR (extrapolated) = 28.8 W/kg SAR(I1 g) =7.81 W/kg; SAR(10 g) = 2.24 W/kg Maximum value of SAR (measured) = 17.6 W/ikg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1 .4mm Reference Value = 71.77 V/m; Power Drift = —0.09 dB Peak SAR (extrapolated) = 31.7 W/kg SAR(1 g) = 8.1 W/kg; SAR(10 g) = 2.32 W/kg Maximum value of SAR (measured) = 18.7 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5750 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 70.36 V/m; Power Drift = —0.08 dB Peak SAR (extrapolated) = 31.5 W/kg SAR(I g) = 7.84 W/kg; SAR(10 g) = 2.23 W/kg Maximum value of SAR (measured) = 18.5 W/kg Certificate No: D5GHzV2—1159_Apr17 Page 8 of 13

—10.00 ~15.00 —20.00 —25.00 0 dB = 18.5 W/kg = 12.67 dBW/kg Certificate No: D5GHzV2—1159_Apr17 Page 9 of 13

Impedance Measurement Plot for Head TSL 25 fApr 2017 12:29133 (CH® sii i uU fs 1147,686 n —6.4961 0 4.6667 pF 5 250.000 000 MHz * CH1 Markers Del 2: 52219 0 ~1,2793 4 for 5.60000 GHz 3: $2,973 a —2.8906 a 5.75000 GHz Ave 16 H1d CH2 CH2 Markers 2:—32.019 dB Cor 5.60000 GHz 3:—27.999 dB 5.75000 GHz fiw tCs H1d START 5 000.000 0G0 MHz STOP 6 000.000 800 MHz Certificate No: D5GHzV2—1159_Apr17 Page 10 of 13

DASY5 Validation Report for Body TSL Date: 18.04.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole DSGHzV2; Type: D5GHzV2; Serial: DSGHzV2 — SN: 1159 Communication System: UID 0 — CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz Medium parameters used: f = 5250 MHz; 0 = 5.5 $/m; & =47.7; p = 1000 kg/m‘ , Medium parameters used: f = 5600 MHz; 0 = 5.97 S$/m; & = 47; p = 1000 kg/m‘ , Medium parameters used: f = 5750 MHz; 0 = 6.18 $/m; & = 46.8; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI €63.19—2011) DASY52 Configuration: «_ Probe: EX3DV4 — SN3503; ConvF(5.14, 5.14, 5.14); Calibrated: 31.12.2016, ConvF(4.57, 4.57, 4.57), Calibrated: 31.12.2016, ConvF(4.51, 4.51, 4.51); Calibrated: 31.12.2016; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 DASY52 52.10.0(1442); SEMCAD X 14.6.10(7413) Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5250MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 66.10 V/m; Power Drift = —0.09 dB Peak SAR (extrapolated) = 29.6 W/kg SAR(1 g) =7.68 W/kg; SAR(10 g) = 2.14 W/kg Maximum value of SAR (measured) = 18.1 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 66.45 V/m; Power Drift = —0.08 dB Peak SAR (extrapolated) = 33.7 W/kg SAR(1 g) = 8.02 W/kg; SAR(10 g) = 2.25 W/kg Maximum value of SAR (measured) = 19.6 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5750 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 64.64 V/m; Power Drift = —0.9 dB Peak SAR (extrapolated) =34.1 W/kg SAR(I g) =7.73 W/kg; SAR(10 g) = 2.15 W/kg Maximum value of SAR (measured) = 20.1 W/kg Certificate No: D5GHzV2—1159_Apr17 Page 11 of 13

—5.00 —10.00 ~15.00 —20.00 —25.00 0 dB = 20.1 W/kg = 13.03 dBW/kg Certificate No: D5GHzV2—1159_Apr17 Page 12 of 13

Impedance Measurement Plot for Body TSL 19 Apr 2017 15:28111 CHZ sn i uors 4: 47.709 a 52559 a 5.7679 pF 5 250.000 @00 MHz CH1 Markers Del 2: 53.727 a 1.6113 o Cor 5.60000 GHz 3: 53.299 a ~893.92 mo 5,75000 GHz fivg 16 H1g CH2 CH2 Markers Cor 2:—28.148 d8 5.60000 GHz 3:—29.628 dB 5.75000 GHz Av 16° H1d START 5 000,000 000 MHz STOP 6 000.000 090 MHz Certificate No: D5GHzV2—1159_Apr17 Page 13 of 13


Document Created: 2017-09-18 10:54:46
Document Modified: 2017-09-18 10:54:46
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC