Test report

FCC ID: BKMAP008

Test Report

Download: PDF
FCCID_3459549

FCC Test Report Report No.: RF170515C18 R1 FCC ID: BKMAP008 Test Model: J-17 Received Date: May 15, 2017 Test Date: May 23 ~ May 25, 2017 Issued Date: Jun. 30, 2017 Applicant: Seiko Epson Corporation Address: 3-3-5 Owa, Suwa-shi, Nagano, 392-8502 Japan Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN (R.O.C.) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF170515C18 R1 Page No. 1 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail............................................................................. 9 3.3 Description of Support Units .............................................................................................................. 11 3.3.1 Configuration of System under Test ................................................................................................... 11 3.4 Duty Cycle of Test Signal ................................................................................................................... 11 3.5 General Description of Applied Standards ........................................................................................ 12 4 Test Types and Results ...................................................................................................................... 13 4.1 Radiated Emission and Bandedge Measurement............................................................................. 13 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 13 4.1.2 Test Instruments ................................................................................................................................ 14 4.1.3 Test Procedures................................................................................................................................. 15 4.1.4 Deviation from Test Standard ............................................................................................................ 15 4.1.5 Test Set Up ........................................................................................................................................ 16 4.1.6 EUT Operating Conditions................................................................................................................. 17 4.1.7 Test Results ....................................................................................................................................... 18 4.2 Conducted Emission Measurement .................................................................................................. 22 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 22 4.2.2 Test Instruments ................................................................................................................................ 22 4.2.3 Test Procedures................................................................................................................................. 22 4.2.4 Deviation from Test Standard ............................................................................................................ 23 4.2.5 Test Setup .......................................................................................................................................... 23 4.2.6 EUT Operating Conditions................................................................................................................. 23 4.2.7 Test Results ....................................................................................................................................... 24 4.3 6dB Bandwidth Measurement ........................................................................................................... 26 4.3.1 Limits of 6dB Bandwidth Measurement ............................................................................................. 26 4.3.2 Test Setup .......................................................................................................................................... 26 4.3.3 Test Instruments ................................................................................................................................ 26 4.3.4 Test Procedure .................................................................................................................................. 26 4.3.5 Deviation from Test Standard ............................................................................................................ 26 4.3.6 EUT Operating Conditions................................................................................................................. 26 4.3.7 Test Result ......................................................................................................................................... 27 4.4 Conducted Output Power Measurement........................................................................................... 28 4.4.1 Limits of Conducted Output Power Measurement ............................................................................ 28 4.4.2 Test Setup .......................................................................................................................................... 28 4.4.3 Test Instruments ................................................................................................................................ 28 4.4.4 Test Procedures................................................................................................................................. 28 4.4.5 Deviation from Test Standard ............................................................................................................ 28 4.4.6 EUT Operating Conditions................................................................................................................. 28 4.4.7 Test Results ....................................................................................................................................... 28 4.5 Power Spectral Density Measurement .............................................................................................. 29 4.5.1 Limits of Power Spectral Density Measurement ............................................................................... 29 4.5.2 Test Setup .......................................................................................................................................... 29 4.5.3 Test Instruments ................................................................................................................................ 29 4.5.4 Test Procedure .................................................................................................................................. 29 4.5.5 Deviation from Test Standard ............................................................................................................ 29 4.5.6 EUT Operating Condition .................................................................................................................. 29 Report No.: RF170515C18 R1 Page No. 2 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.5.7 Test Results ....................................................................................................................................... 30 4.6 Conducted Out of Band Emission Measurement .............................................................................. 31 4.6.1 Limits of Conducted Out of Band Emission Measurement ............................................................... 31 4.6.2 Test Setup .......................................................................................................................................... 31 4.6.3 Test Instruments ................................................................................................................................ 31 4.6.4 Test Procedure .................................................................................................................................. 31 4.6.5 Deviation from Test Standard ............................................................................................................ 31 4.6.6 EUT Operating Condition .................................................................................................................. 31 4.6.7 Test Results ....................................................................................................................................... 32 5 Pictures of Test Arrangements .......................................................................................................... 33 Appendix – Information on the Testing Laboratories ................................................................................ 34 Report No.: RF170515C18 R1 Page No. 3 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

Release Control Record Issue No. Description Date Issued RF170515C18 Original release. Jun. 06, 2017 RF170515C18 R1 Revised address Jun. 30, 2017 Report No.: RF170515C18 R1 Page No. 4 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

1 Certificate of Conformity Product: GPS Wearable Watch Brand: EPSON Test Model: J-17 Sample Status: Engineering sample Applicant: Seiko Epson Corporation Test Date: May 23 ~ May 25, 2017 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.247) ANSI C63.10:2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: Jun. 30, 2017 Pettie Chen / Senior Specialist Approved by : , Date: Jun. 30, 2017 Ken Liu / Senior Manager Report No.: RF170515C18 R1 Page No. 5 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

2 Summary of Test Results 47 CFR FCC Part 15, Subpart C (Section 15.247) FCC Test Item Result Remarks Clause Meet the requirement of limit. 15.207 AC Power Conducted Emission Pass Minimum passing margin is -13.67dB at 1.16600MHz. 15.205 / Meet the requirement of limit. Radiated Emissions and Band Edge 15.209 / Pass Minimum passing margin is -5.3dB at Measurement 15.247(d) 286.00MHz. 15.247(d) Antenna Port Emission Pass Meet the requirement of limit. 15.247(a)(2) 6dB bandwidth Pass Meet the requirement of limit. 15.247(b) Conducted power Pass Meet the requirement of limit. 15.247(e) Power Spectral Density Pass Meet the requirement of limit. 15.203 Antenna Requirement Pass No antenna connector is used. 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Expanded Uncertainty Measurement Frequency (k=2) (±) Conducted Emissions at mains ports 150kHz ~ 30MHz 2.94 dB 30MHz ~ 200MHz 3.63 dB Radiated Emissions up to 1 GHz 200MHz ~1000MHz 3.64 dB 1GHz ~ 18GHz 2.29 dB Radiated Emissions above 1 GHz 18GHz ~ 40GHz 2.29 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: RF170515C18 R1 Page No. 6 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

3 General Information 3.1 General Description of EUT Product GPS Wearable Watch Brand EPSON Test Model J-17 Status of EUT Engineering sample Power Supply Rating 3.7Vdc (Battery) Modulation Type GFSK Transfer Rate 1Mbps Operating Frequency 2402 ~ 2480MHz Number of Channel 40 Channel Spacing 2MHz Output Power 0.6081mW Antenna Type Monopole antenna with 0.1dBi gain Antenna Connector NA Accessory Device NA Data Cable Supplied NA Note: 1. The above EUT information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or user's manual. Report No.: RF170515C18 R1 Page No. 7 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

3.2 Description of Test Modes 40 channels are provided to this EUT: Channel Freq. (MHz) Channel Freq. (MHz) Channel Freq. (MHz) Channel Freq. (MHz) 0 2402 10 2422 20 2442 30 2462 1 2404 11 2424 21 2444 31 2464 2 2406 12 2426 22 2446 32 2466 3 2408 13 2428 23 2448 33 2468 4 2410 14 2430 24 2450 34 2470 5 2412 15 2432 25 2452 35 2472 6 2414 16 2434 26 2454 36 2474 7 2416 17 2436 27 2456 37 2476 8 2418 18 2438 28 2458 38 2478 9 2420 19 2440 29 2460 39 2480 Report No.: RF170515C18 R1 Page No. 8 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

3.2.1 Test Mode Applicability and Tested Channel Detail EUT APPLICABLE TO CONFIGURE DESCRIPTION MODE RE1G RE<1G PLC APCM - √ √ √ √ - Where RE1G: Radiated Emission above 1GHz & RE<1G: Radiated Emission below 1GHz Bandedge Measurement PLC: Power Line Conducted Emission APCM: Antenna Port Conducted Measurement Note: 1. The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on Z-plane. Radiated Emission Test (Above 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGUURE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE DATA RATE (Mbps) MODE - 0 to 39 0, 19, 39 GFSK 1 Radiated Emission Test (Below 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGUURE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE DATA RATE (Mbps) MODE - 0 to 39 39 GFSK 1 Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGUURE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE DATA RATE (Mbps) MODE - 0 to 39 39 GFSK 1 Report No.: RF170515C18 R1 Page No. 9 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

Antenna Port Conducted Measurement: This item includes all test value of each mode, but only includes spectrum plot of worst value of each mode. Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGUURE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE DATA RATE (Mbps) MODE - 0 to 39 0, 19, 39 GFSK 1 Test Condition: APPLICABLE TO ENVIRONMENTAL CONDITIONS INPUT POWER TESTED BY RE1G 23deg. C, 69%RH 120Vac, 60Hz Matthew Yang RE<1G 23deg. C, 69%RH 120Vac, 60Hz Chris Lin PLC 25deg. C, 75%RH 120Vac, 60Hz Chris Lin APCM 25deg. C, 60%RH 120Vac, 60Hz Antony Lee Report No.: RF170515C18 R1 Page No. 10 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

3.3 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. ID Product Brand Model No. Serial No. FCC ID Remarks A. Notebook DELL E5410 6RP2YM1 FCC DoC Approved - Note: 1. All power cords of the above support units are non-shielded (1.8m). 2. Item A acted as a communication partner to transfer data. Shielding ID Descriptions Qty. Length (m) Cores (Qty.) Remarks (Yes/No) 1. RJ45, Cat5e 1 3 N 0 - 3.3.1 Configuration of System under Test EUT (1) Notebook (A) 3.4 Duty Cycle of Test Signal Duty cycle = 100% Report No.: RF170515C18 R1 Page No. 11 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

3.5 General Description of Applied Standards The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.247) 558074 D01 DTS Meas Guidance v04 ANSI C63.10-2013 All test items have been performed and recorded as per the above standards. NOTE: The EUT is also considered as a kind of computer peripheral, because the connection to computer is necessary for typical use. It has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Report No.: RF170515C18 R1 Page No. 12 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement 4.1.1 Limits of Radiated Emission and Bandedge Measurement Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table. Other emissions shall be at least 20dB below the highest level of the desired power: Frequencies Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 Note: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. For frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF170515C18 R1 Page No. 13 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.1.2 Test Instruments Description & Model No. Serial No. Cal. Date Cal. Due Manufacturer Test Receiver ESCI 100424 Oct. 24, 2016 Oct. 23, 2017 ROHDE & SCHWARZ Spectrum Analyzer FSP40 100040 Aug. 16, 2016 Aug. 15, 2017 ROHDE & SCHWARZ BILOG Antenna VULB9168 9168-155 Dec. 28, 2016 Dec. 27, 2017 SCHWARZBECK HORN Antenna BBHA 9120D 9120D-1170 Dec. 15, 2016 Dec. 14, 2017 SCHWARZBECK HORN Antenna BBHA 9170 BBHA9170241 Dec. 14, 2016 Dec. 13, 2017 SCHWARZBECK Loop Antenna EM-6879 269 Aug. 11, 2016 Aug. 10, 2017 Preamplifier 8449B 3008A01960 Aug. 09, 2016 Aug. 08, 2017 Agilent Preamplifier 8447D 2944A10631 Aug. 09, 2016 Aug. 08, 2017 Agilent RF signal cable SUCOFLEX 104 MY 13380+295012/04 Aug. 09, 2016 Aug. 08, 2017 HUBER+SUHNER RF signal cable SUCOFLEX 104 Cable-CH4-03 (250724) Aug. 09, 2016 Aug. 08, 2017 HUBER+SUHNER Software ADT_Radiated_ NA NA NA BV ADT V7.6.15.9.4 Antenna Tower MA 4000 010303 NA NA inn-co GmbH Antenna Tower Controller AT100 AT93021703 NA NA BV ADT Turn Table TT100 TT93021703 NA NA BV ADT Turn Table Controller SC100 SC93021703 NA NA BV ADT Turn Table TT100 TT93021705 NA NA BV ADT Turn Table Controller SC100 SC93021705 NA NA BV ADT High Speed Peak Power ML2495A 0824012 Aug. 11, 2016 Aug. 10, 2017 Meter Power Sensor MA2411B 0738171 Aug. 11, 2016 Aug. 10, 2017 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber 4. 3. The horn antenna and preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The FCC Site Registration No. is 460141. 5. The IC Site Registration No. is IC7450F-4. Report No.: RF170515C18 R1 Page No. 14 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.1.3 Test Procedures For Radiated emission below 30MHz a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. Both X and Y axes of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9kHz at frequency below 30MHz. For Radiated emission above 30MHz a. The EUT was placed on the top of a rotating table 0.8 meters (for 30MHz ~ 1GHz) / 1.5 meters (for above 1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is ≥ 1/T (Duty cycle < 98%) or 3 x RBW (Duty cycle ≥ 98%) for Average detection (AV) at frequency above 1GHz. 4. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 Deviation from Test Standard No deviation. Report No.: RF170515C18 R1 Page No. 15 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.1.5 Test Set Up For Radiated emission below 30MHz 1m EUT& 3m Support Units Turn Table 80cm Ground Plane Test Receiver For Radiated emission 30MHz to 1GHz Ant. Tower 1-4m Variable EUT& 3m 10m Support Units Turn Table 80cm Ground Plane Test Receiver Report No.: RF170515C18 R1 Page No. 16 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

For Radiated emission above 1GHz Ant. Tower 1-4m Variable EUT& 3m Support Units Turn Table Absorber 150cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT Operating Conditions Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF170515C18 R1 Page No. 17 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.1.7 Test Results Above 1GHz Worst-Case Data CHANNEL TX Channel 0 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 25GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 2390.00 56.0 PK 74.0 -18.0 2.73 H 190 23.10 32.90 2 2390.00 45.0 AV 54.0 -9.0 2.73 H 190 12.10 32.90 3 *2402.00 88.3 PK 2.73 H 190 55.40 32.90 4 *2402.00 87.0 AV 2.73 H 190 54.10 32.90 5 4804.00 47.9 PK 74.0 -26.1 1.85 H 268 41.20 6.70 6 4804.00 35.8 AV 54.0 -18.2 1.85 H 268 29.10 6.70 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 2390.00 56.0 PK 74.0 -18.0 3.54 V 275 23.10 32.90 2 2390.00 44.6 AV 54.0 -9.4 3.54 V 275 11.70 32.90 3 *2402.00 83.7 PK 3.54 V 275 50.80 32.90 4 *2402.00 82.2 AV 3.54 V 275 49.30 32.90 5 4804.00 48.9 PK 74.0 -25.1 2.77 V 133 42.20 6.70 6 4804.00 36.3 AV 54.0 -17.7 2.77 V 133 29.60 6.70 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. Report No.: RF170515C18 R1 Page No. 18 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

CHANNEL TX Channel 19 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 25GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2440.00 87.2 PK 2.63 H 186 54.10 33.10 2 *2440.00 85.8 AV 2.63 H 186 52.70 33.10 3 4880.00 48.3 PK 74.0 -25.7 1.76 H 283 41.50 6.80 4 4880.00 35.7 AV 54.0 -18.3 1.76 H 283 28.90 6.80 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2440.00 82.2 PK 3.49 V 278 49.10 33.10 2 *2440.00 80.4 AV 3.49 V 278 47.30 33.10 3 4880.00 48.8 PK 74.0 -25.2 2.80 V 140 42.00 6.80 4 4880.00 36.0 AV 54.0 -18.0 2.80 V 140 29.20 6.80 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. Report No.: RF170515C18 R1 Page No. 19 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

CHANNEL TX Channel 39 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 25GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2480.00 84.4 PK 2.87 H 195 51.10 33.30 2 *2480.00 83.0 AV 2.87 H 195 49.70 33.30 3 2483.50 56.9 PK 74.0 -17.1 2.87 H 195 23.60 33.30 4 2483.50 45.5 AV 54.0 -8.5 2.87 H 195 12.20 33.30 5 4960.00 48.0 PK 74.0 -26.0 1.91 H 295 41.00 7.00 6 4960.00 35.8 AV 54.0 -18.2 1.91 H 295 28.80 7.00 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2480.00 79.8 PK 3.85 V 257 46.50 33.30 2 *2480.00 78.0 AV 3.85 V 257 44.70 33.30 3 2483.50 55.7 PK 74.0 -18.3 3.85 V 257 22.40 33.30 4 2483.50 45.0 AV 54.0 -9.0 3.85 V 257 11.70 33.30 5 4960.00 49.2 PK 74.0 -24.8 1.24 V 219 42.20 7.00 6 4960.00 35.2 AV 54.0 -18.8 1.24 V 219 28.20 7.00 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. Report No.: RF170515C18 R1 Page No. 20 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

Below 1GHz worst-case data CHANNEL TX Channel 39 DETECTOR Quasi-Peak (QP) FREQUENCY RANGE 30MHz ~ 1GHz FUNCTION ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 99.80 34.7 QP 43.5 -8.8 2.00 H 11 53.20 -18.50 2 198.70 36.4 QP 43.5 -7.1 1.00 H 78 52.70 -16.30 3 286.00 40.7 QP 46.0 -5.3 1.26 H 52 53.20 -12.50 4 381.10 34.8 QP 46.0 -11.2 2.00 H 28 45.40 -10.60 5 528.60 32.0 QP 46.0 -14.0 1.51 H 141 40.00 -8.00 6 800.20 38.1 QP 46.0 -7.9 2.00 H 111 40.30 -2.20 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 99.80 27.6 QP 43.5 -15.9 2.00 V 274 46.10 -18.50 2 165.70 31.6 QP 43.5 -11.9 1.00 V 122 45.60 -14.00 3 297.70 30.8 QP 46.0 -15.2 1.24 V 263 43.10 -12.30 4 425.70 35.8 QP 46.0 -10.2 1.24 V 174 45.50 -9.70 5 565.50 30.7 QP 46.0 -15.3 1.00 V 157 38.10 -7.40 6 800.20 31.4 QP 46.0 -14.6 1.24 V 12 33.60 -2.20 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit of frequency range 30MHz ~ 1000MHz. 4. Margin value = Emission Level – Limit value 5. The emission levels were very low against the limit of frequency range 9kHz ~ 30MHz. Report No.: RF170515C18 R1 Page No. 21 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.2 Conducted Emission Measurement 4.2.1 Limits of Conducted Emission Measurement Conducted Limit (dBuV) Frequency (MHz) Quasi-peak Average 0.15 - 0.5 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 4.2.2 Test Instruments Description & Due Date Of Model No. Serial No. Date Of Calibration Manufacturer Calibration Test Receiver ESCI 100613 Nov. 21, 2016 Nov. 20, 2017 ROHDE & SCHWARZ RF signal cable (with 10dB PAD) 5D-FB Cable-cond1-01 Dec. 22, 2016 Dec. 21, 2017 Woken LISN ROHDE & SCHWARZ ESH3-Z5 835239/001 Mar. 10, 2017 Mar. 09, 2018 (EUT) LISN ROHDE & SCHWARZ ESH3-Z5 100311 Jul. 28, 2016 Jul. 27, 2017 (Peripheral) Software BV ADT_Cond_ NA NA NA ADT V7.3.7.3 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 1. 3. The VCCI Site Registration No. is C-2040. 4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not recorded. Note: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15MHz-30MHz. Report No.: RF170515C18 R1 Page No. 22 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.2.4 Deviation from Test Standard No deviation. 4.2.5 Test Setup Vertical Ground Reference Plane Test Receiver EUT 40cm 80cm LISN Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT Operating Conditions Same as 4.1.6. Report No.: RF170515C18 R1 Page No. 23 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.2.7 Test Results Quasi-Peak (QP) / Phase Line (L) Detector Function Average (AV) Channel Channel 39 Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.21805 10.37 30.41 22.30 40.78 32.67 62.89 52.89 -22.11 -20.22 2 0.48700 10.40 30.67 21.97 41.07 32.37 56.22 46.22 -15.15 -13.85 3 1.16600 10.41 29.32 21.92 39.73 32.33 56.00 46.00 -16.27 -13.67 4 2.14200 10.47 29.39 21.43 39.86 31.90 56.00 46.00 -16.14 -14.10 5 4.95800 10.61 25.98 18.85 36.59 29.46 56.00 46.00 -19.41 -16.54 6 15.19800 11.10 23.29 14.32 34.39 25.42 60.00 50.00 -25.61 -24.58 REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. Report No.: RF170515C18 R1 Page No. 24 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

Quasi-Peak (QP) / Phase Neutral (N) Detector Function Average (AV) Channel Channel 39 Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.18200 10.13 35.29 24.85 45.42 34.98 64.39 54.39 -18.97 -19.41 2 0.56600 10.16 29.57 13.78 39.73 23.94 56.00 46.00 -16.27 -22.06 3 1.02200 10.17 24.05 16.48 34.22 26.65 56.00 46.00 -21.78 -19.35 4 2.49400 10.26 28.32 21.73 38.58 31.99 56.00 46.00 -17.42 -14.01 5 5.08600 10.38 23.06 16.09 33.44 26.47 60.00 50.00 -26.56 -23.53 6 17.60200 10.86 21.81 15.20 32.67 26.06 60.00 50.00 -27.33 -23.94 REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. Report No.: RF170515C18 R1 Page No. 25 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.3 6dB Bandwidth Measurement 4.3.1 Limits of 6dB Bandwidth Measurement The minimum of 6dB Bandwidth Measurement is 0.5 MHz. 4.3.2 Test Setup Spectrum EUT Attenuator Analyzer 4.3.3 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.3.4 Test Procedure a. Set resolution bandwidth (RBW) = 100kHz b. Set the video bandwidth (VBW) ≥ 3 x RBW, Detector = Peak. c. Trace mode = max hold. d. Sweep = auto couple. e. Measure the maximum width of the emission that is constrained by the frequencies associated with the two amplitude points (upper and lower) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission 4.3.5 Deviation from Test Standard No deviation. 4.3.6 EUT Operating Conditions The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually. Report No.: RF170515C18 R1 Page No. 26 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.3.7 Test Result 6dB Bandwidth Minimum Limit Channel Frequency (MHz) Pass / Fail (MHz) (MHz) 0 2402 0.69 0.5 Pass 19 2440 0.68 0.5 Pass 39 2480 0.68 0.5 Pass Spectrum Plot of Worst Value Report No.: RF170515C18 R1 Page No. 27 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.4 Conducted Output Power Measurement 4.4.1 Limits of Conducted Output Power Measurement For systems using digital modulation in the 2400–2483.5 MHz bands: 1 Watt (30dBm) 4.4.2 Test Setup EUT Power Sensor Power Meter Attenuator 4.4.3 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.4.4 Test Procedures A peak power sensor was used on the output port of the EUT. A power meter was used to read the response of the peak power sensor. Record the power level. 4.4.5 Deviation from Test Standard No deviation. 4.4.6 EUT Operating Conditions Same as Item 4.3.6. 4.4.7 Test Results Channel Frequency (MHz) Peak Power (mW) Peak Power (dBm) Limit (dBm) Pass/Fail 0 2402 0.6081 -2.16 30 Pass 19 2440 0.5848 -2.33 30 Pass 39 2480 0.5395 -2.68 30 Pass Report No.: RF170515C18 R1 Page No. 28 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.5 Power Spectral Density Measurement 4.5.1 Limits of Power Spectral Density Measurement The Maximum of Power Spectral Density Measurement is 8dBm. 4.5.2 Test Setup Spectrum EUT Attenuator Analyzer 4.5.3 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.5.4 Test Procedure a. Set analyzer center frequency to DTS channel center frequency. b. Set the span to 1.5 times the DTS bandwidth. c. Set the RBW to: 3 kHz ≤ RBW ≤ 100 kHz. d. Set the VBW ≥ 3 × RBW. e. Detector = peak. f. Sweep time = auto couple. g. Trace mode = max hold. h. Allow trace to fully stabilize. i. Use the peak marker function to determine the maximum amplitude level within the RBW. 4.5.5 Deviation from Test Standard No deviation. 4.5.6 EUT Operating Condition Same as Item 4.3.6 Report No.: RF170515C18 R1 Page No. 29 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.5.7 Test Results Freq. PSD Limit Pass Channel (MHz) (dBm) (dBm) /Fail 0 2402 -21.85 8 Pass 19 2440 -22.24 8 Pass 39 2480 -22.73 8 Pass Spectrum Plot of Worst Value Report No.: RF170515C18 R1 Page No. 30 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.6 Conducted Out of Band Emission Measurement 4.6.1 Limits of Conducted Out of Band Emission Measurement Below 20dB of the highest emission level of operating band (in 100kHz Resolution Bandwidth). 4.6.2 Test Setup Spectrum EUT Attenuator Analyzer 4.6.3 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.6.4 Test Procedure MEASUREMENT PROCEDURE REF a. Set the RBW = 100 kHz. b. Set the VBW ≥ 300 kHz. c. Detector = peak. d. Sweep time = auto couple. e. Trace mode = max hold. f. Allow trace to fully stabilize. g. Use the peak marker function to determine the maximum power level in any 100 kHz band segment within the fundamental EBW. MEASUREMENT PROCEDURE OOBE a. Set RBW = 100 kHz. b. Set VBW ≥ 300 kHz. c. Detector = peak. d. Sweep = auto couple. e. Trace Mode = max hold. f. Allow trace to fully stabilize. g. Use the peak marker function to determine the maximum amplitude level. 4.6.5 Deviation from Test Standard No deviation. 4.6.6 EUT Operating Condition Same as Item 4.3.6 Report No.: RF170515C18 R1 Page No. 31 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

4.6.7 Test Results CH 0 CH 19 CH 39 CH 0 Band edge CH 39 Band edge Report No.: RF170515C18 R1 Page No. 32 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

5 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: RF170515C18 R1 Page No. 33 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: RF170515C18 R1 Page No. 34 / 34 Report Format Version: 6.1.1 Cancels and replaces the report No.: RF170515C18 dated Jun. 06, 2017


Document Created: 2017-06-30 18:40:38
Document Modified: 2017-06-30 18:40:38
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC