User Manual

FCC ID: BJ4-WLTX205

Users Manual

Download: PDF
FCCID_2661416

Item #1000 000 000 Safety Information PACKAGE CONTENTS Installation Model #HB-7769-02 1. Please read and understand this entire manual before attempting to assemble, install, or operate this sensor. 5 Mounting the sensor A Use either the small screws (BB) or WARNING: To prevent possible SERIOUS INJURY or DEATH never allow small children near double-sided tape (DD) to mount the USE AND CARE GUIDE batteries. If battery is swallowed, immediately notify a doctor. B C sensor (A).  To mount with the small screws BB (BB), remove the back of sensor NOTE: The range of the wireless doorbell can vary with location, temperature, and battery (A) by pushing in the tab on the ADD ON WIRELESS DOOR SENSOR condition. bottom with a small screwdriver. A Place the sensor (A) back against the mounting surface and mark the This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. two screw holes. Drill two 1/16 in. Operation is subject to the following two conditions: (1) this device may not cause Part Description Quantity pilot holes. Attach the sensor (A) harmful interference, and (2) this device must accept any interference received, including back with the small screws (BB). A Sensor (with preinstalled battery) 1 Tighten securely and snap on the interference that may cause undesired operation. front of the sensor (A). B Magnet 2  When attaching the sensor (A) with The user is cautioned that changes or modifications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the C Spacer 2 double-sided tape (DD), remove paper from both sides of the equipment. double-sided tape (DD) and apply to a clean surface. Care and Cleaning Installation 6 Mounting the magnet A Y A  Use a dry cloth to clean the entry alert. 1 Removing the battery tab  Remove the back of the sensor Use the small screws (BB) (or the large  Do not use cleaners or polishes. screws (CC) if using the magnet spacer (A) by pushing in the tab on the (C)) to mount the magnet (B).  Do not use any fluids on the entry alert. bottom with a small screwdriver (not included).  Remove the back of magnet (B) by P  Remove the orange battery tab pushing in the tab on the bottom Pre-Installation from the sensor (A). of the magnet (B) with a small screwdriver.  Place the magnet (B) back against TOOLS REQUIRED 2 Syncing the push button and SYNC – PRESS the mounting surface and mark the C BB O doorbell AND RELEASE. two screw holes. Illustrations may vary from actual unit.  Press and hold the “SYNC” button RESET – HOLD  Drill two 1/16 in. pilot holes. on the doorbell until the doorbell 10 SECONDS.  Attach the magnet (B) back with sounds a “Beep-Beep”. the small screws (BB). Tighten THANK YOU  Press the button inside the sensor TUNE – HOLD securely and snap on the front of 1 SECOND. the magnet (B). We appreciate the trust and confidence you have placed in Hampton Bay through the (A) within 30 seconds of pressing the doorbell “SYNC” button. C purchase of this add on wireless door sensor. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products  Press the button inside the sensor available for your home improvement needs. Thank you for choosing Hampton Bay! again to activate the doorbell and A Specifications ensure the sensor (A) and doorbell are synced. 30 CR2032 Power requirements Type 2032 3V battery (included) Warranty Phillips screwdriver Small flathead screwdriver Drill FT 3-YEAR LIMITED WARRANTY WHAT IS COVERED 3 Testing doorbell the sensor and  Temporarily position the sensor A Troubleshooting This product is guaranteed to be free of factory defective parts and workmanship for a (A) and magnet (B) where they will LU ME Problem Solution ME VO period of 3 years from date of purchase. Purchase receipt is required for all warranty HI C be mounted. UP claims.  Move the magnet (B) away from SYNC – PRESS AND RELEASE. RESET – HOLD The doorbell does not sound. Make sure batteries are installed according 10 SECONDS. the sensor (A) to simulate a door TUNE – HOLD 1 SECOND. FRONT TRANS REAR to the diagram inside the sensor and WHAT IS NOT COVERED being opened. The red LED should This warranty does not include expendable items (such as light bulbs, batteries, etc.), repair flash and the doorbell will sound doorbell (if applicable). TYPE “C” TYPE “C” TYPE “C” 1/16” (1.5 mm) drill bit Safety goggles service, adjustment and calibration due to misuse, abuse or negligence. Unauthorized “Beep-Beep”. C A  If the doorbell does not sound, Check the charge of the sensor and doorbell service or modification of the product or of any furnished component will void this warranty move the doorbell closer to the in its entirety. This warranty does not include reimbursement for inconvenience, installation, HARDWARE INCLUDED sensor (A) and test again. B batteries (if applicable) and replace if setup time, loss of use, unauthorized service, or return shipping charges. This warranty necessary. is not extended to other equipment and components that a customer uses in conjunction NOTE: Do not permanently mount the with this product. sensor until the sensor and doorbell are Make sure the plug-in doorbell has power R AA working properly. (if applicable). Contact the Customer Service Team at 1-844-760-3644 or visit www.hamptonbay.com. BB 4 Preparing to mount the sensor A Sensor and doorbell are not synced. Follow Step 2 in the Installation section to sync. The maximum gap between the sensor B D (A) and the magnet (B) is 1/2 in.. The The batteries seem okay, but the Metal reduces transmission range. Use 1/4 CC arrows on the face of each component doorbell does not work after installation. in. to 1/2 in. (6 to 13 mm) wood shims to must be aligned and facing each other. move the doorbell or sensor away from the  Place the sensor (A) on the door metal surface. frame and the magnet (B) beside 1/2" Maximum the sensor (A) and ensure the Concrete may reduce range. Move the arrows are aligned.  If the magnet (B) is recessed, use A doorbell away from the concrete surface. DD the spacer (C) to ensure proper alignment. Locate the doorbell closer to the sensor. Part Description Quantity Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service AA Jumper 1 8 a.m. - 5 p.m., CST, Monday - Friday BB Screw - small 4 C B CC Screw - large 2 1-844-760-3644 DD Double-sided tape 1 HAMPTONBAY.COM 208187-01A


Document Created: 2015-05-04 14:50:01
Document Modified: 2015-05-04 14:50:01
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC