6

FCC ID: BGAAL10R

Test Report

Download: PDF
FCCID_12068

REPORT NO: 98E7691 DATE: AUGUST 28, 1998 FCC ID:BGAALIOR VERIFICATION OF COMPLIANCE COMPANY NAME AUDIOVOX CORPORATION 150 MARCUS BOULEVARD HAUPPAUGE, NY 11788 U.S.A. CONTACT PERSON PAT LAVELLE / EXCLUSIVE VICE PRESIDENT TELEPHONE NO. (516) 231—7750 EUT DESCRIPTION 302 MHz RECEIVER MODEL NAME/NUMBER ALK—10 FCC ID BGAAL1OR DATE TESTED AUGUST 28, 1998 REPORT NUMBER 98E7691 TYPE OF EQUIPMENT SECURITY EQUIPMENT (UNINTENTIONAL RADIATOR) EQUIPMENT TYPE 302 MHz SUPERREGENERATE RECEIVER MEASUREMENT PROCEDURE ANSI 63.4 / 1992 LIMIT TYPE CERTIFICATION FCC RULE CFR 47, PART 15.109 The above equipment was tested by Compliance Engineering Services, Inc. for compliance with the requirements set forth in CFR 47, PART 15. This said equipment in the configuration described in this report shows that maximum emission levels emanating from equipment are within the compliance requirements. z~> ~ i _— ’7 /f::£§5”——-- C_ l * es ‘MIKE C.I. KUO / VICE PRESIDENT COMPLIANCE ENGINEERING SERVICES, INC. PAGE NO: 1 COMPLIANCE CONSULTING SERVICES CCS DOCUMENT NO: CCSUP4O021B 1366 BORDEAUX DRIVE, SUNNYVALE CA 94089 TEL:(408)752—8 166 FAX:(408)752—8168 This report shall not be reproduced except in full, without written approvalfrom CCS.

REPORT NO:98E7691 DATE: AUGUST 28, 1998 FCC ID:BGAALIOR 2. PRODUCT DESCRIPTION AUDIOVOX CORP., Model ALK—10 is the receiving portion of a multi—purpose security device. The associated Transmitter is manufactured by Audiovox Corp., Model No: PRO94KR, FCC ID: BGAAV2T . 3. TEST FACILITY The 3 meter open area test site and conducted measurement facility used to collect the radiated data is located at 561F Monterey Road, Morgan Hill, California, U.S.A. A detailed description of the test facilities was submitted to the Commission on May 27, 1994. The measuring instrument which was utilized in performing the tests documented herein has been calibrated in accordance with the manufacturer‘s recommendations for utilizing calibration equipment which is traceable to recognized national standards. 4. MEASUREMENT EQUIPMENT USED Manufacturer Model Description Cal Due Number Date H.P 864 0B Signal Generator os /99 (0.5 — 1024 MHz) H.P 8566B Spectrum Analyzer o9/98 (100Hz — 22GHz) EMCO 3146 Antenna 10/98 (200—1000 MHz) H.P 8447D Preamplifier 09/98 (0.1 — 1309 MHz) PAGE NO: 2 COMPLIANCE CONSULTING SERVICES CCS DOCUMENT NO: CCSUP4021B 1366 BORDEAUX DRIVE, SUNNYVALE CA 94089 TEL:(408)752—8 166 FAX:(408)752—8168 This report shall not be reproduced except in full, without written approvalfrom CCS.

REPORT NO:98E7691 DATE: AUGUST 28, 1998 FCC ID:BGAALLOR ARA DRG—18/A Antenna(1 — 18GHZ) 12/98 H.P. 8449B Preamplifier (1—26.5GHZ) 03/939 5. TEST CONFIGURATION Set signal generator to transmit at 302 MHz. The receiver receives the siqgnal. 6. TESTS CONDUCTED CFR 47, 15.107 CONDUCTED WHEN DEVICE CONNECTED TO AC CODUCTED TESTS LINE CFR 47, 15.109 CONDUCTED AT 3 METERS RADIATED EMISSION TESTS 7. CONDUCTED EMISSION TEST PROCEDURE The EUT is located so that the distance between the boundary of the EUT and the closest surface to the LISN is 0.8m. Conducted disturbance shall be measured between the phase lead and the ground, and between the neutral lead and the ground. The frequency 0.450 — 30 MHz shall be investigated. Set the EMI receiver to PEAK detector setting and sweep continuously over the frequency range to be investigated. Set resolution bandwidth to 9kHz minimum. Connect EMI receiver input cable to LINE 1 RF measurement connection on the LISN. Connect a 50ohm terminator to the unused RF connection on the LISN. For each mode of EUT operation, maximize emissions readings by manipulating cable and wire positions. Record the confiqguration for each EUT power cord which produces emissions closest to the limit. Repeat the same procedure for LINE 2 of each EUT power cord. PAGE NO: 3 COMPLIANCE CONSULTING SERVICES CCS DOCUMENTNO: CCSUP4O21B 1366 BORDEAUX DRIVE, SUNNYVALE CA 94089 TEL:408)752—8166 FAX:(408)752—8168 This report shall not be reproduced except in full, without written approvalfrom CCS.

REPORT NO:98E7691 DATE: AUGUST 28, 1998 FCC ID:BGAALIOR RADIATED EMISSION TEST PROCEDURE The EUT and all other support equipment are placed on a wooden table 80 cm above the ground screen. Antenna to EUT distance is 3 meters. During the test, the table is rotated 360 degrees to maximize emissions and the antenna is positioned from 1 to 4 meters above the ground screen to further maximize emissions. The antenna is polarized in both vertical and horizontal positions. Monitor the frequency range of interest at a fixed antenna height and EUT azimuth. Frequency span should be small enough to easily differentiate between broadcast stations and intermittent ambients. Rotate EUT 360 degrees to maximize emissions received from EUT. If emission increases by more than 1 dB, or if another emission appears that is greater by 1 dB, return to azimuth where maximum occurred and perform additional cable manipulation to further maximize received emission. Move antenna up and down to further maximize suspected highest amplitude signal. If emission increased by 1 dB or more, or if another emission appears that is greater by 14B or more, return to antenna height where maximum signal was observed and manipulate cables to produce highest emissions, noting frequency and amplitude. COHERENT TESTS During Radiated Emission Tests, H.P. signal generator model no: 8640B (0.5 — 1024 MHz) was used to radiate unmodulated CW signal to EUT at 302.0 MHz. Please refer to radiated emission data no: 980828B1l for six highest readings. 10. EQUIPMENT MODIFICATIONS To achieve compliance to FCC section 15.109, the following change(s) were made during compliance testing: NOT APPLICABLE PAGE NO: 4 COMPLIANCE CONSULTING SERVICES CCS DOCUMENT NO: CCSUP4O21B 1366 BORDEAUX DRIVE. SUNNYVALE CA 94089 TEL:(408)752—8166 FAX:(408)752—8168 This report shall not be reproduced except in full, without written approvalfrom CCS.

Project No. 98E7691 Compliance Engineering Services Inc. Report No. 980828B1 Date 08/28/1998 Time 11;34 >> 3 M RADIATED EMISSION DATA <«< Test Engr JESSE SALDIVAR /4 Company AUDIOVOX CORPORATION Equipment Under Test 302MHZ RX MODEL ALK—10 Test Configuration EUT/SIGNAL GENERATOR Type of Test FCC CLASS B Mode of Operation RX Freq. dBuv PreAmp Ant Cable dBuV/m Limit Margin Pol Hgt(m) Az 6 WORST EMISSIONS: 302 .35 44 .20 —26. 74 14 .51 3 .68 35.65 46.00 —10.35 H 1.0 0 302 .98 44 .30 —26 .75 14 .51 3 .69 35.76 46.00 —10.24 H 1.0 0 916 .21 36.20 —27 .44 23 .33 7.03 39.11 46.00 —6 .89 H 1.0 0 915 .61 35.80 —27 .45 23 .32 7.03 38 .70 46.00 —7.30 H 1.0 0 914 .93 35 .80 —27 45 23 .31 7.03 38 .68 46.00 —7 .32 H 1.0 0 917 .63 35.50 —27. 44 23 35 7.04 38 .45 46.00 —7.55 H 1.0 0 Total # of data v. b2 .2

AUDIOYVOX ALK—10 FCC ID BGaaAY2RT MKR 3601.63 MHz Liey RAEF 97.0 dB w ATTEN 10 dB 79.60 dBu #— r—— 1 1 momor o ro=> > ] 10 asB.,/ | DL 44 . 4 dB W | —i— | | | } |j w!.l«ll.! Lcp22222 2s i.fll«;QO,II»»J.‘ onl zlc lll renrmmannmons enpmene mm mimmmhenemmen > i | | 1 i | j 1 } t | 1 { i [ I CENTER 295.6 MHz SsPAN 45.0 MHz RES BW 100 kHz VBW 100 kHz SWP 20.0 msec

sesu g‘°M2e dMS ZHX G0F MBA ZH% GMA% MGg S34 ZHW C@°PZ NYAS ZHW L‘ T0E HSLN3D t [JTToTT T | } | f M | | | | omm zommofrhn dsmnmocfrmen ces i 1 | i | | o ooe M | | i “ e| i ; | | T f T + [~ T | ;| 9I i | M i | i | i ; oooo l Map 1 , 1 ; ; 6BE | ; A | | i | : : : 10 [ : | W i i W w — 2gp of _T . .. n ssis l _ nnn e ds s h sies cb collll Ml se l M mm s :hi\.,,} leduiclls AL J mep o5 s.2 sp o; muliv A"gp g 26 s=34 / ZHXW OP C PPE HYiW ilz2A¥yYI8 OfI 394 d:i—ywuv xoaoTony


Document Created: 2001-07-10 02:33:55
Document Modified: 2001-07-10 02:33:55
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC