User Manual R

FCC ID: BEJLGSBWAC93

Users Manual

Download: PDF
FCCID_4276707

User Manual PRODUCT NAME : RF Module MODEL NAME : LGSBWAC93 The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek. (00)-0073

DOCUMENT No : - REG. DATE : 2019.04.03 User Manual REV.NO : V1.0 MODEL NAME: TWCM-K504D(LGIT) REV. DATE : 2019.04.03 LGSBWAC93(LGE) PAGE : 1 / 9 Index No Description Page 1 Features 2 2 Picture of Product 2 3 Installation Manual 3 4 Block Diagram 4 5 Absolute Maximum Ratings 4 6 Operating Conditions 5 7 Standard Test Conditions 5 8 Pin Description 6 9 Out Drawing 7 10 Packing Information 8 Copyrightⓒ. 2014. All Rights Reserved.

DOCUMENT No : - REG. DATE : 2019.04.03 User Manual REV.NO : V1.0 MODEL NAME: TWCM-K504D(LGIT) REV. DATE : 2019.04.03 LGSBWAC93(LGE) PAGE : 2 / 9 1. Features TWCM-K504D is the small size and low power module for IEEE 802.11ac wireless LAN & BT5.0 + HS. TWCM-K504D is based on Mediatek MT7668AUN solution.  IEEE 802.11 a/b/g/n/ac Dual Band Dual Concurrent (DBDC)  Bluetooth 5.0+ HS , BLE (*This device does not support BT(BT 5.0+ HS, BLE) function as disabled by software.)  Size : 68.0mm x 30.0 x 7.35 mm  Two stream spatial multiplexing up to 300Mbps(802.11n) / 867Mbps(802.11ac) Use on-chip OTP (One-Time Programmable)  Host Interface : USB2.0 (WLAN & BT) - This model is using the common USB2.0 to control WLAN and BT  Security : WAPI, WEP, WPA, WPA2, WMM, AES, TKIP, CKP  Application: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB 2. Picture of Product Copyrightⓒ. 2014. All Rights Reserved.

DOCUMENT No : - REG. DATE : 2019.04.03 User Manual REV.NO : V1.0 MODEL NAME: TWCM-K504D(LGIT) REV. DATE : 2019.04.03 LGSBWAC93(LGE) PAGE : 3 / 9 3. Installation Manual Install the module like below in the back of the TV TWCM-K504D installed position Copyrightⓒ. 2014. All Rights Reserved.

DOCUMENT No : - REG. DATE : 2019.04.03 User Manual REV.NO : V1.0 MODEL NAME: TWCM-K504D(LGIT) REV. DATE : 2019.04.03 LGSBWAC93(LGE) PAGE : 4 / 9 4. Block Diagram MT7668AUN 32bit 2.4GHz WiFi Diplexer RISC OTP 5GHz Baseband MCU USB I/F 12PIN CONNECTOR ANT2 WiFi RF 2.4GHz WiFi MAC Packet USB2.0 Diplexer DMA 5GHz Interface WiFi MAC BT ANT PTA 2.4GHz BT RF RF_CTL PMU 40MHz Main 3.3V Clock 5. Absolute Maximum Ratings Caution : The specifications in Table 1 define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. Parameter Min Max Unit Storage Temperature -20 +80 ℃ Storage Humidity (40℃) - 90 % . Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40℃ and 20 to 60%. 3) Assemble the modules within 6 months. Check the soldering ability in case of 6 months over. Copyrightⓒ. 2014. All Rights Reserved.

DOCUMENT No : - REG. DATE : 2019.04.03 User Manual REV.NO : V1.0 MODEL NAME: TWCM-K504D(LGIT) REV. DATE : 2019.04.03 LGSBWAC93(LGE) PAGE : 5 / 9 6. Operating Conditions Parameter Min Typ Max Unit Ambient Temperature 0 - 60 ℃ Ambient Humidity (40℃) - - 85 % Supply Voltage 3.135 3.3 3.6 Vdc 7. Standard Test Conditions The Test for electrical specification shall be performed under the following condition Otherwise this following conditions, not guaranteed this performance. 7-1. Ambient condition Temparature 25 ± 5℃ Humidity 65 ± 5% 7-2. Power supply voltages Input Voltage Supply Voltage VDD_3.3V 3.135 ~ 3.6V Copyrightⓒ. 2014. All Rights Reserved.

DOCUMENT No : - REG. DATE : 2019.04.03 User Manual REV.NO : V1.0 MODEL NAME: TWCM-K504D(LGIT) REV. DATE : 2019.04.03 LGSBWAC93(LGE) PAGE : 6 / 9 8. Pin Description Pin No. Pin Name I/O Pin Description 1 VCC I VDD 3.3V 2 D- I/O USB Communication signal USB_DN 3 D+ I/O USB Communication signal USB_DP 4 GND - GND 5 WOWL O Wake On WLAN 6 VCC I VDD 3.3V 7 RESUME I SUSPEND_RESUME 8 GND - GND 9 RESET I Bluetooth device wake up (option) Host wake up. 10 WOBLE O (Signal from Wi-Fi module to the host) 11 GND - GND 12 VCC - VDD 3.3V Copyrightⓒ. 2014. All Rights Reserved.

DOCUMENT No : - REG. DATE : 2019.04.03 User Manual REV.NO : V1.0 MODEL NAME: TWCM-K504D(LGIT) REV. DATE : 2019.04.03 LGSBWAC93(LGE) PAGE : 7 / 9 9. Outline Drawing 3D View '19. 03. 27 K.S Lee '19. 03. 27 I.H Park '19. 03. 27 S.D Chol Copyrightⓒ. 2014. All Rights Reserved.

DOCUMENT No : - REG. DATE : 2019.04.03 User Manual REV.NO : V1.0 MODEL NAME: TWCM-K504D(LGIT) REV. DATE : 2019.04.03 LGSBWAC93(LGE) PAGE : 8 / 9 10. Packing Information Copyrightⓒ. 2014. All Rights Reserved.

| Lwa a~ TOH w esbce mul es romemnetemime vouatemims rnimeeimimnne tonmene) s tm — peo t [t—a j( a| 8E ~ Chkre g _ rrincan tke mow — Weatntesim mss 31— Camlatrsimares w denpornnt u.mte tmend _ 4| cmneam 1 Y pa===—} T—Oisrase #—O1Cite] ssm + T & T © 1 Teatepiveerouu o1 sis sov. o VitoveSD 1 e wosioz: aivo ho mcowss imwuew 105n oTarisrNoML SAVNTIIION wrome amoos en inann000 @

DOCUMENT No : - REG. DATE : 2019.04.03 User Manual REV.NO : V1.0 MODEL NAME: TWCM-K504D(LGIT) REV. DATE : 2019.04.03 LGSBWAC93(LGE) PAGE : 10 / 9 <FCC Compliance> This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Copyrightⓒ. 2014. All Rights Reserved.

DOCUMENT No : - REG. DATE : 2019.04.03 User Manual REV.NO : V1.0 MODEL NAME: TWCM-K504D(LGIT) REV. DATE : 2019.04.03 LGSBWAC93(LGE) PAGE : 11 / 9 <Regulatory notice to host manufacturer according to KDB 996369 D03 OEM Manual v01> 2.2 List of applicable FCC rules This module has been granted modular approval as below listed FCC rule parts. - FCC Rule parts 15C(15.247) and 15E(15.407) 2.3 Summarize the specific operational use conditions - The OEM integrator should use equivalent antennas which is the same type and equal or less gain then an antenna listed in 2.7 in this instruction manual. 2.4 Limited module procedures - N/A 2.5 Trace antenna designs - N/A 2.6 RF exposure considerations The module has been certified for integration into products only by OEM integrators under the following condition: - The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. - The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. - Mobile use As long as the three conditions above are met, further transmitter testing will not be required. OEM integrators should provide the minimum separation distance to end users in their end- product manuals. 2.7 Antennas list This module is certified with the following integrated antenna. - Type: FPCB antenna (Peak gain (dBi): 2.89 (Ant1) / 2.91 (Ant2)) Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive change procedure. Copyrightⓒ. 2014. All Rights Reserved.

DOCUMENT No : - REG. DATE : 2019.04.03 User Manual REV.NO : V1.0 MODEL NAME: TWCM-K504D(LGIT) REV. DATE : 2019.04.03 LGSBWAC93(LGE) PAGE : 12 / 9 2.8 Label and compliance information End Product Labeling The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following: “Contains FCC ID: BEJLGSBWAC93” “Contains IC: 2703H-LGSBWAC93” 2.9 Information on test modes and additional testing requirements - OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, additional transmitter in the host, etc.). 2.10 Additional testing, Part 15 Subpart B disclaimer - The final host product also requires Part 15 subpart B compliance testing with the modular transmitter installed to be properly authorized for operation as a Part 15 digital device. Copyrightⓒ. 2014. All Rights Reserved.

DOCUMENT No : - REG. DATE : 2019.04.03 User Manual REV.NO : V1.0 MODEL NAME: TWCM-K504D(LGIT) REV. DATE : 2019.04.03 LGSBWAC93(LGE) PAGE : 13 / 9 2. ISED RSS-GEN, Sec. 7.1.3– (licence-exempt radio apparatus) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. RF Exposure The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna or transmitter. l'exposition aux RF L’antenne (ou les antennes) doit être installée de façon à maintenir à tout instant une distance minimum de au moins 20 cm entre la source de radiation (l’antenne) et toute personne physique. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. Attention: Les changements ou modifications de cet appareil non expressément approuvé par le fabricant peuvent annuler votre droit à utiliser cet équipement. É tiquetage du produit final (IC) Le module BT111 est étiqueté avec sa propre identification FCC et son propre numéro de certification IC. Si l’identification FCC et le numéro de certification IC ne sont pas visibles lorsque le module est installé à l’intérieur d’un autre dispositif, la partie externe du dispositif dans lequel le module est installé devra également présenter une étiquette faisant référence au module inclus. Dans ce cas, le produit final devra être étiqueté sur une zone visible avec les informations suivantes : « Contient module émetteur identification FCC ID: BEJLGSBWAC93 « Contient module émetteur IC : 2703H- LGSBWAC93” “The 5150-5250 MHz band is restricted to indoor use only.” Copyrightⓒ. 2014. All Rights Reserved.

DOCUMENT No : - REG. DATE : 2019.04.03 User Manual REV.NO : V1.0 MODEL NAME: TWCM-K504D(LGIT) REV. DATE : 2019.04.03 LGSBWAC93(LGE) PAGE : 14 / 9 3. CE Simplified EU Declaration of Conformity Hereby, LG Electronics Inc. declares that the radio equipment type RF Module is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.lg.com/global/support/cedoc/cedoc# RF Exposure The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna or transmitter The use of the 5150 – 5350 MHz band is restricted to indoor use only. This restriction will be applied in all member states. Manufacturer name: LG Electronics Inc. The postal address: LG Electronics European Shared Service Center B.V. Krijgsman 1, 1186 DM Amstelveen, The Netherlands The host manufacturer has the responsibility that the host device should be compliance with all essential requirement of RED. Copyrightⓒ. 2014. All Rights Reserved.


Document Created: 2019-05-14 16:11:28
Document Modified: 2019-05-14 16:11:28
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC