MPE Calculation

FCC ID: BEJE19MAE07

RF Exposure Info

Download: PDF
FCCID_3706880

"n GUMI UNIVERSITY EMC CENTER Page 1 of15 MPE TEST REPORT Applicant: LG Electronics USA. Date of Issue: Dec. 26, 2017 1000 Sylvan Avenue, Order Number: GETEC—C1—17—578 Englewood Cliffs New Jersey United States 07632, Test Report Number: GETEC—E3—17—054 Attn: Kyung—Su Han / Director Test Site: GUMI UNIVERSITY EMC CENTER (FCC Test Firm Registration No.: 269701) FCC ID. _: BEJE1IMAEO7 Applicant LG Electronics USA. Rule Part(s) : FCC Part 1 Test Procedure : FCC Part 1, Subpart I, section 1.1310 and KDB 680106 DO1 VO2 EUT Type : Refrigerator Type of Authority : Certification Model Name : SKSFD3604P Trade Mark : LG This equipment has been shown to be in compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in 47 CFR Part 1, Subpart I, section 1.1310 and KDB 680106 DO1 VO2 I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the vest of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Tested by, Reviewed by, W S Sang Hyun Park, Associate Engineer Hyoung SeLofKJ}fnfTe[chnh}\Manager GUMI UNIVERSITY EMC CENTER GUMI UNIVERSITY EMC CENTER GETEC—QP—28—007 (Rev.02) EMC CENTER This test report only contains the result of a specific sample supplied for the examination. It is not allowed to copy this report even partly without the approval of EMC center GUMIUNIVERSITY EMC CENTER

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 2 / 15 CONTENTS 1. GENERAL INFORMATION ...................................................................................................................................... 3 2. INTRODUCTION ........................................................................................................................................................ 4 3. PRODUCT INFORMATION ...................................................................................................................................... 5 3.1 DESCRIPTION OF EUT .............................................................................................................................................. 5 3.2 DEFINITION OF MODELS ........................................................................................................................................... 5 3.3 SUPPORT EQUIPMENT / CABLES USED ..................................................................................................................... 5 3.4 MODIFICATION ITEM(S) ........................................................................................................................................... 5 4. DESCRIPTION OF TESTS ......................................................................................................................................... 6 4.1 TEST CONDITION ...................................................................................................................................................... 6 5. TEST EQUIPMENT USED ......................................................................................................................................... 6 6. TEST RESULT ............................................................................................................................................................. 7 6.1 TEST SETUP .............................................................................................................................................................. 7 6.2 MEASUREMENT PROCEDURE ................................................................................................................................... 7 6.3 EQUIPMENT APPROVAL CONSIDERATIONS. ............................................................................................................. 8 6.4 ENVIRONMENTAL EVALUATION AND EXPOSURE LIMIT............................................................................................ 9 6.5 E AND H FIELD STRENGTH ..................................................................................................................................... 10 6.5.1 FIELD STRENGTH MEASURE VALUE AT 10 CM FROM THE EDGES SURROUNDING THE EUT .............................. 10 7. PHOTOGRAPHS ....................................................................................................................................................... 11 7.1 TEST PHOTOGRAPHS .............................................................................................................................................. 11 EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 3 / 15 Scope: Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and / or unintentional radiators for compliance with technical rules and regulations of the Federal Communications Commission. 1. General Information Applicant: LG Electronics USA. Applicant Address: 1000 Sylvan Avenue, Englewood Cliffs New Jersey United States 07632 Manufacturer: LG Electronics Inc. Manufacturer Address: 170, Sungsanpaechong-ro, Seongsan-gu, Changwon-si, Gyeongsangnam-do, 642-711, Korea Contact Person: Bogeun Lee / Research Engineer Tel. Number: +82-55-260-3966  FCC ID. BEJE19MAE07  EUT Type Refrigerator  Model Name SKSFD3604P  Rule Part(s) FCC Part 1  Type of Authority Certification  Test Procedure(s) FCC Part 1, Subpart I, section 1.1310 and KDB 680106 D01 V02  Dates of Test Dec. 22, 2017  Place of Test GUMI UNIVERSITY EMC CENTER (FCC Test Firm Registration Number: 269701) 37 Yaeun-ro, Gumi-si, Gyeongsangbuk-do, 730-711, Republic of Korea.  Test Report Number GETEC-E3-17-054  Dates of Issue Dec. 26, 2017 EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 4 / 15 2. Introduction The measurement procedure described in American National Standard for Methods of Measurement of Radio-Nose Emissions From Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz (ANSI C63.4- 2014) was used in determining radiated and conducted emissions emanating from LG Electronics USA. Refrigerator (Model name: SKSFD3604P) These measurement tests were conducted at GUMI UNIVERSITY EMC CENTER. The site address is 37 Yaeun-ro, Gumi-si, Gyeongsangbuk-do, 730-711, Gyeongnam 641-713, Korea This test site is one of the highest point of GUMI UNIVERSITY at about 200 kilometers away from Seoul city and 40 kilometers away from Daegu city. It is located in the valley surrounded by mountains in all directions where ambient radio signal conditions are quiet and a favorable area to measure the radio frequency interference on open field test site for the computing and ISM devices manufactures. The detailed description of the measurement facility was found to be in compliance with the requirements of §2.948 according to ANSI C63.4 (2014) GUMI UNIVERSITY EMC CENTER 37 Yaeun-ro, Gumi-si, Gyeongsangbuk-do, 730-711, Gyeongnam 641-713, Korea Tel: +82-54-440-1195 Fax: +82-54-440-1199 Fig 1. The map above shows the GUMI UNIVERSITY in vicinity area. EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 5 / 15 3. Product Information 3.1 Description of EUT The Equipment under Test (EUT) is the LG Electronics USA. Refrigerator (Model Name: SKSFD3604P) FCC ID.: BEJE19MAE07. Type of Equipment Refrigerator Model Name SKSFD3604P Serial Number Prototype RF Frequency 330 kHz ~ 370 kHz External connector DC input 1 EA Rated Voltage Input : AC 115 V, 60 Hz ( Wireless Power Transmitter input voltage: DC 12 V) Output Electricity Power Less than 3 W Size(W x H x T) 35 3/4(W) x23 7/8(D) x831/2(H) inch (Wireless Power Transmitter module :50 (mm) x 35 (mm) x 1.0 (mm)) 3.2 Definition of models - None. 3.3 Support Equipment / Cables used 3.3.1 Used Support Equipment Description Manufacturer Model Name S/N & FCC ID. S/N: - None - - FCC ID.: - See “Appendix E – Test Setup Photographs” for actual system test set-up 3.3.2 System configuration Description Manufacturer Model Name S/N & FCC ID. S/N: -. None. - - FCC ID.: -. 3.3.3 Used Cable(s) Cable Name Condition Description Power cable Connected to the EUT and AC power 2.20 m Unshielded. 3.4 Modification Item(s) -. None EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 6 / 15 4. Description of tests 4.1 Test Condition The EUT was installed, arranged and operated in a manner that is most representative of equipment as typically used. The measurements were carried out while varying operating modes and cable positions within typically arrangement to determine maximum emission level. The representative and worst test mode(s) were noted in the test report.  Test Voltage / Frequency: AC 115V, 60 Hz ( Wireless Power Transfer Device were supplied DC 12 V from main system)  Operating condition during the test(s) : This device has been tested in the configurations of charging mode Charging Current Support Equipment Comment 1 000 mA Refrigerator Shelf RX module 5. Test Equipment used Model Name Manufacturer Description Serial Number Due to Calibration  - ELT-400 Narda Safety Test Solutions GmbH EMF Tester J-0005 Sep. 09, 2018  - HI-6105 ETS LINDGREN Electric field Probe 203871 Dec. 21, 2018 All test equipment used is calibrated on a regular basis. EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 7 / 15 6. Test Result 6.1 Test Setup Side Side11 Side Side55 Side Side44 Side Side22 Side Side66 Side Side33 6.2 Measurement Procedure The RF exposure test was performed on 360 degree turn table in anechoic chamber. The measurement probe was placed at test distance ( 10 ㎝) which is between the edge of the charger and the geometric center of probe. The turn table was rotated 360 degree to search of highest strength. The highest emission level was recorded and compared with limit as soon as measurement of each points (Side 1 ~ 6) were completed. The EUT were measured according to the dictates of KDB 680106 D01v02. EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 8 / 15 6.3 Equipment Approval Considerations. The EUT does with item 5.2 of KDB 680106 D01v02 a) Power transfer frequency is less that 1 ㎒ - Power transfer(Main Carrier) frequency is fixed between 330 kHz ~ 370 kHz b) Output power from each primary coil is less than 5 watts. - The maximum field strength of fundamental : 59.28 dBµV/m at 3 m. The EIRP calculation is reference to KDB 789033 ※ EIRP[dBm] = E[dBµV/m]+20log(d[meters]) -104.77 - 4.8 dB, d = 3 m ※ 59.28 dBµV/m – 95.2 -4.8 = -40.72 dBm EIRP ※ The output power from primary coil is 0.000 084 ㎽ c) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils - The system is consists of single primary and secondary coils. d) Client device is inserted in or placed directly in contact with the transmitter - Client device(Receiver) is placed by the transmitter with a less than 10 mm gap. Refer to following photo. e) The maximum coupling surface area of the transmit(charging) device is between 60 cm2 and 400 cm2 - The shape of primary and secondary coils are same and the they are center-aligned. Maximum coupling surface area of transmitter is under 20 cm2 f) Aggregate leakage fields at 10 cm surrounding the device from all simultaneous transmitting coils are demonstrated to be less than 30% of the MPE limit. - 0.478 A/m (maximum measure value) < 0.489 A/m (30% MPE limit) EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 9 / 15 6.4 Environmental evaluation and exposure limit * according to FCC CFR 47 part 1, 1.1307(b), 1.1310 §1.1310 : The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in §1.1307(b), except in the case of portable devices which shall be evaluated according to the provisions of FCC part 2.1093 of this chapter Table 1 – LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Electric Field Magnetic Field Power Density Average Time 2 Range Strength(V/m) Strength(A/m) (mW/cm ) (minutes) (MHz) (A) Limits for Occupational /Control Exposures 0.3 – 3.0 614 1.63 *(100) 6 3.0 – 30 1842/f 4.89/f *(900/f2) 6 30 – 300 61.4 6.163 1.0 6 300 – 1 500 f/300 6 1 500 – 100 000 5 6 (B) Limits for General Population / Uncontrol Exposures 0.3 – 1.34 614 1.63 *(100) 30 2 1.34 – 30 824/f 2.19 *(180/f ) 30 30 – 300 27.5 0.073 0.2 30 300 – 1 500 f/1 500 30 1 500 – 100 000 1.0 30 F=frequency in MHz * = Plane wave equivalent power density Note 1 to Table 1: Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. Note 2 to Table 1: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 10 / 15 6.5 E and H field strength Temperature : 23.9 ℃ Relative Humidity : 29.2 % R.H. Air pressure : 101.3 kPa Test mode : Continuous Power transmitting mode 6.5.1 Field Strength measure value at 10 cm from the edges surrounding the EUT Electric Field Strength Test Position Probe Measure Result(V/m) Limit(V/m) 30 % Limit(V/m) Side 1 32.22 614 184.2 Side 2 32.11 614 184.2 Side 3 22.49 614 184.2 Side 4 28.99 614 184.2 Side 5 10.96 614 184.2 Magnetic Field Strength Test Position Probe Measure Result(A/m) Limit(A/m) 30 % Limit(A/m) Side 1 0.131 1.63 0.489 Side 2 0.161 1.63 0.489 Side 3 0.105 1.63 0.489 Side 4 0.099 1.63 0.489 Side 5 0.478 1.63 0.489 EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 11 / 15 7. Photographs 7.1 Test Photographs Test model No.: SKSFD3604P Test with full load Side 1 < Electric field > < Magnetic field > EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 12 / 15 Side 2 < Electric field > < Magnetic field > EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 13 / 15 Side 3 < Electric field > < Magnetic field > EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 14 / 15 Side 4 < Electric field > < Magnetic field > EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C

Order Number : GETEC-C1-17-578 FCC Part 1 Test Report Number : GETEC-E3-17-054 Page 15 / 15 Side 5 < Electric field > < Magnetic field > - The end - EUT Type: Refrigerator FCC ID.: BEJE19MAE07 G E T E C


Document Created: 2018-01-02 13:11:43
Document Modified: 2018-01-02 13:11:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC