04 Cover Letter-Modular Approval FCC_WB1NP9

FCC ID: BEJ-WB1NP9

Cover Letter(s)

Download: PDF

FCCID_4317443

Cover Letter-Modular Approval

FCC ID: BEJ-WB1NP9 Date: Apr. 30, 2019

Gentlemen:
There’s an WB1NP9 that would like to have your authorization as a modular approval.
The specific product as below, WB1NP9 with its designed features and specified description,
meets special requirements for Full modular approval on FCC KDB996369 by cross-reference list
below.
Company LG Electronics USA
Model Name Bluetooth Module
Model Number WB1NP9
FCC ID BEJ-WB1NP9

Requirement of FCC KDB996369 Comply（Y/N）
1. The modular transmitter must have its Y
own RF shielding.
2. The modular transmitter must have buffered Y
modulation/data inputs (if such inputs are The EUT has its buffered modulation. Please
provided) to ensure that the module will see the Schematic Diagram.
comply with Part 15 requirements under
conditions of excessive data rates or
over-modulation.
3. The modular transmitter must have its Y
own power supply regulation.
4. The modular transmitter must comply with the Y
antenna and transmission system requirements The EUT meets the FCC antenna
of Sections 15.203, 15.204(b) and 15.204(c). requirements; unique antenna connector and
The antenna must either be permanently photo of antenna are shown in the test report.
attached or employ a “unique” antenna coupler
(at all connections between the module and the
antenna, including the cable). The
“professional installation” provision of Section
15.203 is not applicable to modules but can
apply to limited modular approvals under
paragraph (b) of this section.
5. The modular transmitter must be tested Y
in a stand alone configuration, i.e., the The EUT was tested with a test board, Please
module must not be inside another device see test report and setup photo
during testing.
6. The modular transmitter must be labeled with Y
its own FCC ID number, and, if the FCC ID is Please see exhibition label sample for the
not visible when the module is installed inside FCC ID of this module. And also in the

another device, then the outside of the device exhibition Users manual, there are
into which the module is installed must also instructions give to the OEM on how to label
display a label referring to the enclosed the end product.
module. This exterior label can use wording
such as the following: “Contains Transmitter
Module FCC ID: FCC ID” or “Contains FCC
ID: FCC ID” Any similar wording that
expresses the same meaning may be used.
The Grantee may either provide such a label,
an example of which must be included in the
application for equipment authorization, or,
must provide adequate instructions along with
the module which explain this requirement.
In the latter case, a copy of these instructions
must be included in the application for
equipment authorization.
7. The modular transmitter must comply Y
with any specific rule or operating The EUT is compliant with all applicable
requirements applicable to the transmitter FCC rules. Details instructions for
and the manufacturer must provide adequate maintaining compliance are give in the User
instructions along with the module to Manual.
explain any such requirements. A copy of
these instructions must be included in the
application for equipment authorization.
8. The modular transmitter must comply Y
with any applicable RF exposure The EUT complies with RF exposure
requirements. For example, FCC Rules in requirement.
Sections 2.1091, 2.1093 and specific
Sections of Part 15, including 15.319(i),
15.407(f), 15.253(f) and 15.255(g), require
that Unlicensed PCS, UNII and millimeter
wave devices perform routine environmental
evaluation for RF Exposure to demonstrate
compliance. In addition, spread spectrum
transmitters operating under Section 15.247
are required to address RF Exposure
compliance in accordance with Section
15.247(b)(4).

Thank you.
Sincerely,

Document Created: 2019-05-08 10:24:37
Document Modified: 2019-05-08 10:24:37

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC