A1549 FCC LTE Report_No Photos_Part5

FCC ID: BCG-E2816A

Test Report

Download: PDF

FCCID_2373483

REPORT NO: 14U17673-E19D DATE: AUGUST 27, 2014
MODEL: A1549 FCC ID: BCG-E2816A

9.3. FIELD STRENGTH OF SPURIOUS RADIATION
RULE PART(S)
FCC: §2.1053, §22.917, §24.238 and §27.53

LIMIT
§22.917 (e) and §24.238 (a): Out of band emissions. The power of any emission outside of the
authorized operating frequency ranges must be attenuated below the transmitting power (P) by
a factor of at least 43 + 10 log (P) dB.
§27.53 (g) For operations in the 698–746 MHz band, the power of any emission outside a
licensee's frequency band(s) of operation shall be attenuated below the transmitter power (P)
within the licensed band(s) of operation, measured in watts, by at least 43 + 10 log (P) dB.
§27.53 (h) For operations in the 1710–1755 MHz and 2110–2155 MHz bands, the power of any
emission outside a licensee's frequency block shall be attenuated below the transmitter power
(P) by at least 43 + 10 log10(P) dB.

TEST PROCEDURE
For Cellular equipment - Compliance with these rules is based on the use of measurement
instrumentation employing a resolution bandwidth of 100 kHz or greater. In the 1 MHz bands
immediately outside and adjacent to the frequency block a resolution bandwidth of at least one
percent of the emission bandwidth of the fundamental emission of the transmitter may be
employed. A narrower resolution bandwidth is permitted in all cases to improve measurement
accuracy provided the measured power is integrated over the full required measurement
bandwidth (i.e. 100 kHz or 1 percent of emission bandwidth, as specified). The emission
bandwidth is defined as the width of the signal between two points, one below the carrier center
frequency and one above the carrier center frequency, outside of which all emissions are
attenuated at least 26 dB below the transmitter power.

For PCS equipment - Compliance with these rules is based on the use of measurement
instrumentation employing a resolution bandwidth of 1 MHz or greater. However, in the 1 MHz
bands immediately outside and adjacent to the frequency block a resolution bandwidth of at
least one percent of the emission bandwidth of the fundamental emission of the transmitter may
be employed. A narrower resolution bandwidth is permitted in all cases to improve
measurement accuracy provided the measured power is integrated over the full required
measurement bandwidth ( i.e. 1 MHz or 1 percent of emission bandwidth, as specified). The
emission bandwidth is defined as the width of the signal between two points, one below the
carrier center frequency and one above the carrier center frequency, outside of which all
emissions are attenuated at least 26 dB below the transmitter power.

Page 645 of 765
UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J
47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888
This report shall not be reproduced except in full, without the written approval of UL

REPORT NO: 14U17673-E19D DATE: AUGUST 27, 2014
MODEL: A1549 FCC ID: BCG-E2816A

The unwanted emission power shall be measured with a resolution bandwidth of at least 1% of
the occupied bandwidth in the 1 MHz band immediately outside and adjacent to the channel
edge of the equipment. Beyond the 1 MHz band immediately outside the channel edge of the
equipment, a resolution bandwidth of 1 MHz shall be employed. A narrower resolution
bandwidth is allowed to be used provided that the measured power is integrated over the full
required measurement bandwidth of 1 MHz or 1% of the occupied bandwidth as applicable.
The power of any unwanted emissions measured from the channel edge of the equipment shall
be attenuated below the transmitter power, P (dBW), as follows:
a. for base station and subscriber equipment, other than mobile subscriber equipment, the
attenuation shall not be less than 43 + 10 Log10 (p), dB; and
b. for mobile subscriber equipment, the attenuation shall not be less than 43 + 10 Log10
(p), dB at the channel edges and 55 + 10 Log10 (p) at 5.5 MHz away and beyond the channel
edges where p in (a) and (b) is the transmitter power measured in watts.

MODES TESTED
 LTE Band 2
 LTE Band 4
 LTE Band 5
 LTE Band 13
 LTE Band 17
 LTE Band 25
 LTE Band 26
RESULTS

Page 646 of 765
UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J
47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888
This report shall not be reproduced except in full, without the written approval of UL

Document Created: 2019-06-28 23:10:21
Document Modified: 2019-06-28 23:10:21

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC