SAR test report 6 of 6

FCC ID: BCG-A2178

RF Exposure Info

Download: PDF
FCCID_4264981

Calibration s Laboratory of i ty/7 NR\ S Schweizerischer Kalibrierdienst S es Schmid & Partner i’lfififlé c Service suisse d‘étalonnage Englneenng AG > ¢_—\\ §3 Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ‘f/,,/f\\\\\\@ S Swiss Calibration Service Aulabs® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client UL CCS USA Certificate No: D2450V2—706_May18 CALIBRATION CERTIFICATE Object D2450V2 — SN:706 Calibration procedure(s) QA CAL—O5.v10 Calibration procedure for dipole validation kits above 700 MHz Calibration date: May 18, 2018 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—18 (No. 217—02672/02673) Apr—19 Power sensor NRP—Z91 SN: 103244 04—Apr—18 (No. 217—02672) Apr—19 Power sensor NRP—Z91 SN: 103245 04—Apr—18 (No. 217—02673) Apr—19 Reference 20 dB Attenuator SN: 5058 (20k) 04—Apr—18 (No. 217—02682) Apr—19 Type—N mismatch combination SN: 5047.2 / 06327 04—Apr—18 (No. 217—02683) Apr—19 Reference Probe EX3DV4 SN: 7349 30—Dec—17 (No. EX8—7349_Dec17) Dec—18 DAE4 SN: 601 26—Oct—17 (No. DAE4—601_Oct17) Oct—18 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: US37292783 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) In house check: Oct—18 RF generator R&S SMT—O6 SN: 100972 15—Jun—15 (in house check Oct—16) In house check: Oct—18 Network Analyzer HP 8753E SN: US37390585 18—Oct—01 (in house check Oct—17) In house check: Oct—18 Name Function Signature Calibrated by: Manu Seitz Laboratory Technician a Approved by: Katja Pokovic Technical Manager /f@ Issued: May 22, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D2450V2—706_May18 Page 1 of 9

Calibration ( l Laboratory of uyY oS\ AN S . & Het ‘ Schweizerischer Kalibrierdienst & & Schmid & Partner ifii c Service suisse d‘étalonnage Engineering AG y Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland t/fi\\\v‘ S Swiss Calibration Service Alnl uks® Accredited by the Swiss Accreditation Service (SAS) Accreditatior: No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multitateral Agreement for the recognition of calikration certificates Glossary: TSL tissue simulating liquid Convr sensitivity in TSL / NORM x.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: «& Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. » Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. s SAR measured: SAR measured at the stated antenna input power. s SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D2450V2—706_May18 Page 2 of 9

Measurement Conditions DASY system configuration, as far as not given onpage 1. DASY Version DASY5 V52.10.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2450 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 38.2 + 6 % 1.85 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 13.4 Wikg SAR for nominal Head TSL parameters normalized to 1W 52.6 W/ikg + 17.0 % (k=2) SAR averaged over 10 cm‘ (10 g) of Head TSL condition SAR measured 250 mW input power 6.22 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.6 Wikg + 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 52.3 +6 % 1.99 mho/m + 6 % Body TSL temperature change during test <0.5 °C es ———— SAR result with Body TSL SAR averaged over 1 cm‘® (1 g) of Body TSL Condition SAR measured 250 mW input power 12.8 W/kg SAR for nominal Body TSL parameters normalized to 1W 50.6 W/kg + 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 5.96 Wikg SAR for nominal Body TSL parameters normalized to 1W 23.7 Wikg + 16.5 % (k=2) Certificate No: D2450V2—706_May18 Page 3 of 9

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 52.1 Q + 6.8 |Q Return Loss — 23.1 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 47.1 0 + 6.6 jQ Return Loss — 22.6 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.143 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on May 28, 2002 Certificate No: D2450V2—706_May18 Page 4 of 9

DASY5 Validation Report for Head TSL Date: 18.05.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT : Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN:706 Communication System: UID 0 — CW ; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; o = 1.85 S$/m; & = 38.2; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(7.88, 7.88, 7.88) @ 2450 MHz; Calibrated: 30.12.2017 Sensor—Surface: 1.4mm (Mechanical Surface Detection) Electronics: DAE4 Sn601; Calibrated: 26.10.2017 Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) ® Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 116.9 V/m; Power Drift = —0.07 dB Peak SAR (extrapolated) = 26.7 W/kg SAR(1 g) = 13.4 W/kg; SAR(10 g) = 6.22 W/kg Maximum value of SAR (measured) = 22.0 W/kg dB 0 —5.00 —10.00 —15.00 —20.00 —25.00 0 dB = 22.0 W/kg = 13.42 dBW/kg Certificate No: D2450V2—706_May18 Page 5 of 9

Impedance Measurement Plot for Head TSL 18 May 2018 @§8:55:31 CH1) s11 1 U FS 1: 52117 & 68047 a 442.04 pH 2 4590.000 900 MHz De 1 Cor A 169 H1 d CH2Z Ay ast H1d START 2 250.000 06BB MHz STOP 2 650.0990 dod MHz Certificate No: D2450V2—706_May18 Page 6 of 9

DASY5 Validation Report for Body TSL Date: 18.05.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN:706 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 1.99 S/m; & = 52.3; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: s Probe: EX3DV4 — SN7349; ConvF(8.01, 8.01, 8.01) @ 2450 MHz; Calibrated: 30.12.2017 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 26.10.2017 e Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 »_— DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 107.2 V/m; Power Drift = —0.08 dB Peak SAR (extrapolated) = 25.3 W/kg SAR(1 g) = 12.8 W/kg; SAR(10 g) = 5.96 W/kg Maximum value of SAR (measured) = 20.5 W/kg dB 0 —5.00 —10.00 —15.00 —20.00 —25.00 0 dB = 20.5 W/kg = 13.12 dBW/kg Certificate No: D2450V2—706_May18 Page 7 of 9

Impedance Measurement Plot for Body TSL 18 May 2018 88:52155 CHI) s4i $ UUFS 1: 47.086 a 6.6133 m 429.61 pH 2 450.900 @B0 MHz @7 -—”-'- ¢ k‘-\\\ ~ + + _ }~ La B# T e TT \ * Jd :\\ Del Cor Ava 16 H1d CH2 Cor Av 16 2 H1d START 2 259.000 0G0 MHz STOP 2 650.000 008 MHz Certificate No: D2450V2—706_May18 Page 8 of 9

Appendix (Additional assessments outside the scope of SCS 0108) Evaluation Condition Phantom SAM Head Phantom For usage with cSAR3SDV2—R/L SAR result with SAM Head (Top) SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR (average measured) 250 mW input power 13.9 W/kg SAR for nominal Head TSL parameters normalized to 1W 55.9 Wikg + 17.5 % (k=2) SAR averaged over 10 cm® (10 g) of Head TSL condition SAR measured 250 mW input power 6.49 Wikg SAR for nominal Head TSL parameters normalized to 1W 26.1 W/kg + 16.9 % (k=2) SAR result with SAM Head (Mouth) SAR averaged over 1 cm® (1 g) of Head TSL Condition SAR (average measured) 250 mW input power 14.2 Wikg SAR for nominal Head TSL parameters normalized to 1W 57.0 Wikg * 17.5 % (k=2) SAR averaged over 10 cm® (10 g) of Head TSL condition SAR (average measured) 250 mW input power 6.82 W/kg SAR for nominal Head TSL parameters normalized to 1W 27.4 Wikg * 16.9 % (k=2) SAR result with SAM Head (Neck) SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR (average measured) 250 mW input power 13.3 W/kg SAR for nominal Head TSL parameters normalized to 1W 53.7 Wikg * 17.5 % (k=2) SAR averaged over 10 cm® (10 g) of Head TSL condition SAR (average measured) 250 mW input power 6.22 Wikg SAR for nominal Head TSL parameters normalized to 1W 25.0 Wikg + 16.9 % (k=2) SAR result with SAM Head (Ear) SAR averaged over 1 cm® (1 g) of Head TSL Condition SAR (average measured) 250 mW input power 8.56 W/kg SAR for nominal Head TSL parameters normalized to 1W 34.4 Wikg + 17.5 % (k=2) SAR averaged over 10 cm® (10 g) of Head TSL condition SAR (average measured) 250 mW input power 4.32 Wikg SAR for nominal Head TSL parameters normalized to 1W 17.4 Wikg + 16.9 % (k=2) Certificate No: D2450V2—706_May18 Page 9 of 9

Calibration Laboratory of \\\‘\\‘ [ l”II'// S Schweizerischer Kalibrierdienst 7 Schmid & Partner 2 C Service suisse d‘étalonnage Engineering AG ilac—mrA Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client UL CCS USA Certificate No: D5GHzV2—1138_Aug18 ICALIBRATIQN CERTIFICATE l Object D5GHzV2 — SN:1138 Calibration procedure(s) QA CAL—22.v3 Calibration procedure for dipole validation kits between 3—6 GHz Calibration date: August 21, 2018 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—18 (No. 217—02672/02673) Apr—19 Power sensor NRP—Z91 SN: 103244 04—Apr—18 (No. 217—02672) Apr—19 Power sensor NRP—Z91 SN: 103245 04—Apr—18 (No. 217—02673) Apr—19 Reference 20 dB Attenuator SN: 5058 (20k) 04—Apr—18 (No. 217—02682) Apr—19 Type—N mismatch combination SN: 5047.2 / 06327 04—Apr—18 (No. 217—02683) Apr—19 Reference Probe EX3DV4 SN: 3503 30—Dec—17 (No. EX3—3503_Dec17) Dec—18 DAE4 SN: 601 26—Oct—17 (No. DAE4—601_Oct17) Oct—18 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: US37292783 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) In house check: Oct—18 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Oct—16) In house check: Oct—18 Network Analyzer Agilent E8358A SN: US41080477 31—Mar—14 (in house check Oct—17) In house check: Oct—18 Name Function Signature Calibrated by: Michael Weber Laboratory Technician f » Katja Pokovic Technical Manager /f E? Approved by: Issued: August 22, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D5GHzV2—1138_Aug18 Page 1 of 16

Calibration Laboratory of J Schweizerischer Kalibrierdienst f s > S Schmid & Partner ii%é c Service suisse d‘étalonnage Engineering AG 2wy Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland *4/fi\‘>° S Swiss Calibration Service Alnlubs® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid Convr sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: # Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D5GHzV2—1138_Aug18 Page 2 of 16

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.10.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy = 4.0 mm, dz =1.4 mm Graded Ratio = 1.4 (Z direction) 5250 MHz + 1 MHz Frequency 5600 MHz + 1 MHz 5750 MHz + 1 MHz Head TSL parameters at 5250 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.71 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.6 +6 % 4.61 mho/m +6 % Head TSL temperature change during test <0.5 °C ———— a——— SAR result with Head TSL at 5250 MHz SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR measured 100 mW input power 8.28 W/kg SAR for nominal Head TSL parameters normalized to 1W 82.6 Wikg + 19.9 % (k=2) SAR averaged over 10 cm® (10 g) of Head TSL condition SAR measured 100 mW input power 2.39 W/kg SAR for nominal Head TSL parameters normalized to 1W 23.8 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1138_Aug18 Page 3 of 16

Head TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.1 46 % 4.98 mho/m + 6 % Head TSL temperature change during test <0.5 °C =——— ———— SAR result with Head TSL at 5600 MHz SAR averaged over 1 cm® (1 g) of Head TSL Condition SAR measured 100 mW input power 8.63 W/kg SAR for nominal Head TSL parameters normalized to 1W 86.0 W / kg + 19.9 % (k=2) SAR averaged over 10 cm*® (10 g) of Head TSL condition SAR measured 100 mW input power 2.47 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.6 W/ikg + 19.5 % (k=2) Head TSL parameters at 5750 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.4 5.22 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 34.9 + 6 % 5.14 mho/im +6 % Head TSL temperature change during test <0.5 °C ———— SAR result with Head TSL at 5750 MHz SAR averaged over 1 cm*° (1 g) of Head TSL Condition SAR measured 100 mW input power 8.27 W/ikg SAR for nominal Head TSL parameters normalized to 1W 82.4 Wikg * 19.9 %(k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.37 W/kg SAR for nominal Head TSL parameters normalized to 1W 23.6 W/ikg + 19.5 % (k=2) Certificate No: D5GHzV2—1138_Aug18 Page 4 of 16

Body TSL parameters at 5250 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.36 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.9 £ 6 % 5.49 mho/im +6 % Body TSL temperature change during test <0.5 °C ———— SAR result with Body TSL at 5250 MHz SAR averaged over 1 cm® (1 g) of Body TSL Condition SAR measured 100 mW input power 7.72 Wikg SAR for nominal Body TSL parameters normalized to 1W 76.6 W/ikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.16 W/kg SAR for nominal Body TSL parameters normalized to 1W 21.4 Wikg + 19.5 % (k=2) Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.3 + 6 % 5.96 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5600 MHz SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 8.01 W/kg SAR for nominal Body TSL parameters normalized to 1W 79.5 Wi/kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.24 Wikg SAR for nominal Body TSL parameters normalized to 1W 22.2 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1138_Aug18 Page 5 of 16

Body TSL parameters at 5750 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.3 5.94 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.0 +6 % 6.16 mho/m + 6 % Body TSL temperature change during test <0.5 °C ———— SAR result with Body TSL at 5750 MHz SAR averaged over 1 cm® (1 g) of Body TSL Condition SAR measured 100 mW input power 7.47 Wikg SAR for nominal Body TSL parameters normalized to 1W 74.1 Wikg + 19.9 % (k=2) SAR averaged over 10 cm® (10 g) of Body TSL condition SAR measured 100 mW input power 2.08 Wikg SAR for nominal Body TSL parameters normalized to 1W 20.6 Wi/kg + 19.5 % (k=2) Certificate No: D5GHzV2—1138_Aug18 Page 6 of 16

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL at 5250 MHz Impedance, transformed to feed point 48.0 0 — 5.9 jQ Return Loss — 23.9 dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 54.2 O — 5.4 |Q Return Loss — 23.6 dB Antenna Parameters with Head TSL at 5750 MHz Impedance, transformed to feed point 52.5 Q — 4.3 jQ Return Loss — 26.3 dB Antenna Parameters with Body TSL at 5250 MHz Impedance, transformed to feed point 47.7 Q — 4.2 |Q. Return Loss — 26.1 dB Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 54.8 O — 4.4 jQ Return Loss — 24.1 dB Antenna Parameters with Body TSL at 5750 MHz Impedance, transformed to feed point 53.2 Q — 3.7 jQ Return Loss — 26.5 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.201 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on May 07, 2012 Certificate No: D5GHzV2—1138_Aug18 Page 7 of 16

DASY5 Validation Report for Head TSL Date: 21.08.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole D5GHzV2; Type: D5GHzV2; Serial: D5GHzV2 — SN: 1138 Communication System: UID 0 — CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz Medium parameters used: £= 5250 MHz; o = 4.61 S/m; & = 35.6; p = 1000 kg/m, Medium parameters used: f = 5600 MHz; 6 = 4.98 S/m; & = 35.1; p = 1000 kg/m? , Medium parameters used: f = 5750 MHz; 0 = 5.14 S/m; & = 34.9; p = 1000 kg/m>} Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C€63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(5.51, 5.51, 5.51) @ 5250 MHz, ConvF(5.05, 5.05, 5.05) @ 5600 MHz, ConvF(4.98, 4.98, 4.98) @ 5750 MHz; Calibrated: 30.12.2017 s« Sensor—Surface:; 1.4mm (Mechanical Surface Detection) «_ Electronics: DAFE4 Sn601; Calibrated: 26.10.2017 e Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 _ DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Head Tissue/Pin=100mW, dist=1{mm, £=5250 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 76.67 V/m; Power Drift = —0.09 dB Peak SAR (extrapolated) = 28.3 W/kg SAR(1 g) = 8.28 W/kg; SAR(10 g) = 2.39 W/kg Maximum value of SAR (measured) = 18.4 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 76.43 V/m; Power Drift = —0.07 dB Peak SAR (extrapolated) = 32.6 W/kg SAR(1 g) = 8.63 W/kg; SAR(10 g) = 2.47 W/kg Maximum value of SAR (measured) = 20.2 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5750 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 74.23 V/m; Power Drift = —0.09 dB Peak SAR (extrapolated) = 31.7 W/kg SAR(1 g) = 8.27 W/kg; SAR(10 g) = 2.37 W/kg Maximum value of SAR (measured) = 19.3 W/kg Certificate No: D5GHzV2—1138_Aug18 Page 8 of 16

—5.00 —10.00 —15.00 —20.00 —25.00 0 dB = 19.3 W/kg = 12.86 dBW/kg Certificate No: D5GHzV2—1138_Aug18 Page 9 of 16

Impedance Measurement Plot for Head TSL File Y¥iew Channel Sweep Calibration Trace Scale Marker— System Window Help 1: 5.250000 GHz 47 .983 0 54429 pF 5.9945 0 3: 5.600000 GHz 54.193 0 5.29374pF —5.4265 0 3: 5.750000 GHz 52.487 0 64847 pF <125940 >R: 5.500000 GHz ©8.982 mU ~102.95 ® Ch1s&wg= 20 Ch1: Start $.00000 GHz ———— Stop £.00000 GHz .00 . f GHz —23.949 dB 5.00 GHz —26.347 dB o0 .00 .Gd .10 .Gf 35.00 18 Ch 1 = Chi: Start 5.00000 GHa ——— Stop €.00000 GHz Status CH 1: C" 1—Port Avg=20 Delay LCL Certificate No: D5GHzV2—1138_Aug18 Page 10 of 16

DASY5 Validation Report for Body TSL Date: 21.08.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT : Dipole D5GHzV2; Type: D5GHzV2; Serial: DS5GHzV2 — SN: 1138 Communication System: UID 0 — CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz Medium parameters used: f = 5250 MHz; 0 = 5.49 S/m; s = 46.9; p = 1000 l(g/m3 , Medium parameters used: f = 5600 MHz; 0 = 5.96 S/m; s, = 46.3; p = 1000 kg/m3 t Medium parameters used: £= 5750 MHz; 0 = 6.16 S/m; & = 46; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: + Probe: EX3DV4 — SN3503; ConvF(5.26, 5.26, 5.26) @ 5250 MHz, ConvF(4.65, 4.65, 4.65) @ 5600 MHz, ConvF(4.57, 4.57, 4.57) @ 5750 MHz; Calibrated: 30.12.2017 *« Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 26.10.2017 e Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 e DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5250 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 67.82 V/m; Power Drift = —0.07 dB Peak SAR (extrapolated) = 29.0 W/kg SAR(1 g) =7.72 W/kg; SAR(10 g) = 2.16 W/kg Maximum value of SAR (measured) = 17.8 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0; Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 68.08 V/m; Power Drift = —0.08 dB Peak SAR (extrapolated) = 32.9 W/kg SAR(1 g) = 8.01 W/kg; SAR(10 g) = 2.24 W/kg Maximum value of SAR (measured) = 18.9 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5750 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 66.23 V/m; Power Drift = —0.09 dB Peak SAR (extrapolated) = 31.4 W/kg SAR(I g) =7.47 W/kg; SAR(10 g) = 2.08 W/kg Maximum value of SAR (measured) = 18.1 W/kg Certificate No: D5GHzV2—1138_Aug18 Page 11 of 16

—5.00 —10.0¢ —15.00 —20.00 —25.00 0 dB = 18.1 W/kg = 12.58 dBW/kg Certificate No: D5GHzV2—1138_Aug18 Page 12 of 16

Impedance Measurement Plot for Body TSL File ¥iew Channe!l Sweep Calibration Trace Scale Marker System Window Help ooo mmmimikiticc : 1: 5.250000 GHzs 47.655 0 7A901pF 422210 2: 5.500000 GHz 54.948 0 §4321pF 44185 0 l 3: 5750000 GHz 52.226 0 _ TSegEpF <queses n | >R: 5500000 GHz 54488 m —44.700 * Ch1Awg= 20 Ch1: Start 5.00000 §Hz —— Stop £.00000 GHz GHz —26.1244B GHz 26.519 4B II .00 10 0 Ch 1 = “ Chi: Start 5.00000 GHz ——— Stop £.00000 GHz CH 1: C" 1—Port Avg=20 Delay Certificate No: D5GHzV2—1138_Aug18 Page 13 of 16

Appendix (Additional assessments outside the scope of SCS 0108) Evaluation Conditions (f=5250 MHz) Phantom SAM Head Phantom For usage with cSAR3DV2—R/L SAR result with SAM Head (Top) SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR (average measured) 100 mW input power 8.66 W/kg SAR for nominal Head TSL parameters normalized to 1W 86.5 W/kg + 20.3 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.49 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 24.9 Wikg + 19.9 % (k=2) SAR result with SAM Head (Mouth) SAR averaged over 1 cm® (1 g) of Head TSL Condition SAR (average measured) 100 mW input power 8.58 W/kg SAR for nominal Head TSL parameters normalized to 1W 85.7 Wi/kg + 20.3 % (k=2) SAR averaged over 10 cm® (10 g) of Head TSL condition SAR (average measured) 100 mW input power 2.41 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 24.1 Wi/kg + 19.9 % (k=2) SAR result with SAM Head (Neck) SAR averaged over 1 cm® (1 g) of Head TSL Condition SAR (average measured) 100 mW input power 8.37 W/kg SAR for nominal Head TSL parameters normalized to 1W 84.5 Wikg + 20.3 % (k=2) SAR averaged over 10 cm® (10 g) of Head TSL condition SAR (average measured) 100 mW input power 2.39 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 23.9 W/kg + 19.9 % (k=2) SAR result with SAM Head (Ear) SAR averaged over 1 cm® (1 g) of Head TSL Condition SAR (average measured) 100 mW input power 5.42 W/kg SAR for nominal Head TSL parameters normalized to 1W 54.2 Wi/ikg + 20.3 % (k=2) SAR averaged over 10 cm° (10 g) of Head TSL condition SAR (average measured) 100 mW input power 1.84 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 18.3 Wikg + 19.9 % (k=2) Certificate No: D5GHzV2—1138_Aug18 Page 14 of 16

Apper:dix (Additional assessments outside the scope of SCS 0108) Evaluation Conditions (f=5600 MHz) Phantom SAM Head Phantom For usage with cSAR3DV2—R/L SAR result with SAM Head (Top) SAR averaged over 1 cm?® (1 g) of Head TSL Condition SAR (average measured) 100 mW input power 9.18 W/kg SAR for nominal Head TSL parameters normalized to 1W 91.1 W/kg + 20.3 % (k=2) SAR averaged over 10 cm‘ (10 g) of Head TSL condition SAR measured 100 mW input power 2.60 W/kg SAR for nominal Head TSL parameters normalized to 1W 25.7 Wikg + 19.9 % (k=2) SAR result with SAM Head (Mouth) SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR (average measured) 100 mW input power 9.37 W/kg SAR for nominal Head TSL parameters normalized to 1W 93.0 W/kg + 20.3 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR (average measured) 100 mW input power 2.69 W/kg SAR for nominal Head TSL parameters normalized to 1W 26.6 Wi/kg + 19.9 % (k=2) SAR result with SAM Head (Neck) SAR averaged over 1 cm® (1 g) of Head TSL Condition SAR (average measured) 100 mW input power 8.80 W/kg SAR for nominal Head TSL parameters normalized to 1W 87.4 Wi/kg + 20.3 %(k=2) SAR averaged over 10 cm® (10 g) of Head TSL condition SAR (average measured) 100 mW input power 2.40 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.8 Wikg + 19.9 % (k=2) SAR result with SAM Head (Ear) SAR averaged over 1 cm® (1 g) of Head TSL Condition SAR (average measured) 100 mW input power 6.28 W/kg SAR for nominal Head TSL parameters normalized to 1W 62.3 Wi/kg + 20.3 % (k=2) SAR averaged over 10 cm® (10 g) of Head TSL condition SAR (average measured) 100 mW input power 210 Wikg SAR for nominal Head TSL parameters normalized to 1W 20.8 W/kg + 19.9 % (k=2) Certificate No: D5GHzV2—1138_Aug18 Page 15 of 16

Appendix (Additional assessments outside the scope of SCS 0108) Evaluation Conditions (f=5750 MHz) Phantom SAM Head Phantom For usage with cSAR3DV2—R/L SAR result with SAM Head (Top) SAR averaged over 1 cm® (1 g) of Head TSL Condition SAR (average measured) 100 mW input power 8.67 W/kg SAR for nominal Head TSL parameters normalized to 1W 86.4 Wi/kg + 20.3 % (k=2) SAR averaged over 10 cm‘ (10 g) of Head TSL condition SAR measured 100 mW input power 2.46 W/kg SAR for nominal Head TSL parameters normalized to 1W 24.5 Wikg + 19.9 % (k=2) SAR result with SAM Head (Mouth) SAR averaged over 1 cm® (1 g) of Head TSL Condition SAR (average measured) 100 mW input power 8.61 W/kg SAR for nominal Head TSL parameters normalized to 1W 85.8 W/kg * 20.3 % (k=2) SAR averaged over 10 cm® (10 g) of Head TSL condition SAR (average measured) 100 mW input power 2.40 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.9 W/kg + 19.9 % (k=2) SAR result with SAM Head (Neck) SAR averaged over 1 cm® (1 g) of Head TSL Condition SAR (average measured) 100 mW input power 8.10 W/kg SAR for nominal Head TSL parameters normalized to 1W 80.7 Wi/kg + 20.3 % (k=2) SAR averaged over 10 cm® (10 g) of Head TSL condition SAR (average measured) 100 mW input power 2.27 W/kg SAR for nominal Head TSL parameters normalized to 1W 22.6 Wikg + 19.9 % (k=2) SAR result with SAM Head (Ear) SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR (average measured) 100 mW input power 5.77 Wikg SAR for nominal Head TSL parameters normalized to 1W 57.5 Wikg * 20.3 % (k=2) SAR averaged over 10 cm® (10 g) of Head TSL condition SAR (average measured) 100 mW input power 1.94 Wikg SAR for nominal Head TSL parameters normalized to 1W 19.3 Wikg + 19.9 % (k=2) Certificate No: D5GHzV2—1138_Aug18 Page 16 of 16


Document Created: 2019-03-28 23:06:57
Document Modified: 2019-03-28 23:06:57
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC