Test report

FCC ID: BCE-OTE070

Test Report

Download: PDF
FCCID_3709243

FCC Measurement/Technical Report on OTE070 & OTE071 Jabra Elite 65t FCC ID: BCE-OTE070 & BCE-OTE071 IC ID: 2386C-OTE070 & 2386C-OTE071 Report Reference: MDE_GNAUD_1707_FCCd Test Laboratory: 7layers GmbH Borsigstrasse 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7layers GmbH Geschäftsführer/ Borsigstraße 11 Managing Directors: Registergericht/registered: a Bureau Veritas 40880 Ratingen, Germany Frank Spiller Düsseldorf HRB 75554 Group Company T +49 (0) 2102 749 0 Bernhard Retka USt-Id.-Nr./VAT-No. DE203159652 F +49 (0) 2102 749 350 Alexandre Norré-Oudard Steuer-Nr./TAX-No. 147/5869/0385 www.7layers.com Commerzbank AG Account No. 303 016 000 Bank Code 300 400 00 IBAN DE81 3004 0000 0303 0160 00 Swift Code COBADEFF

Table of Contents 0 Summary 3 Technical Report Summary 3 Measurement Summary / signatures 4 Administrative Data 5 Testing Laboratory 5 Project Data 5 Applicant Data 5 Manufacturer Data 5 1 Test object Data 6 General EUT Description 6 EUT Main components 7 Ancillary Equipment 7 Auxiliary Equipment 7 EUT Setups 7 Operating Modes 8 Special software used for testing 8 Product labelling 8 2 Test Results 9 Spurious radiated emissions 9 Peak power output 13 3 Measurement uncertainty 14 4 Test equipment 14 5 Antenna Factors, Cable Loss and Sample Calculations 16 LISN R&S ESH3-Z5 (150 kHz – 30 MHz) 16 Antenna R&S HFH2-Z2 (9 kHz – 30 MHz) 17 Antenna R&S HL562 (30 MHz – 1 GHz) 18 Antenna R&S HF907 (1 GHz – 18 GHz) 19 Antenna EMCO 3160-09 (18 GHz – 26.5 GHz) 20 Antenna EMCO 3160-10 (26.5 GHz – 40 GHz) 21 6 Photo Report 21 7 Setup Drawings 21 8 FCC and IC Correlation of measurement requirements 23 9 Annex measurement plots 24 Radiated emissions and peak output power 24 Test report reference: MDE_GNAUD_1707_FCCd Page 2 of 24

0 Summary Technical Report Summary Type of Authorization Certification for an intentional radiator: 10.6 MHz Near Field Magnetic Induction (NFMI) radio Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 and 15 (10-1-15 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart C – Intentional Radiators § 15.205 Restricted bands of operation § 15.207 Conducted limits § 15.209 Radiated emission limits; general requirements § 15.215 Additional provisions to the general radiated emission limitations Note: ANSI C63.10-2013 applied Summary Test Results: The EUT complied with all performed tests as listed in chapter 0.2 Measurement Summary. Test report reference: MDE_GNAUD_1707_FCCd Page 3 of 24

0.2 Measurement Summary / signatures # layers A Bureau Veritas Group Company 47 CFR Chapter I FCC Part 15, Subpart C §15.209 Radiated Emissions The measurement was performed according to ANSI C63.10 OP—Mode Setup Port Final Result op—mode 1 Setup_O1 Enclosure passed 47 CFR Chapter I FCC Part 15, Subpart C §15.209 Peak Output Power The measurement was performed according to ANSI C63.10 OP—Mode Setup Port Final Result op—mode 1 Setup_O1 Enclosure passed Notes: N/A = Not applicable )u Lv UM\\ [A C402 (responsible for accreditation scope) (responsible for testing and report) Dipl.—Ing. Marco Kullik Dipl.—Ing. Daniel Gall /layers 7 layers GmbH, Borsigstr. 11 40880 Ratingen, Germany Phone +49 (0)2102 749 0 Test report reference: MDE_GNAUD_1707_FCCd Page 4 of 24

Administrative Data Testing Laboratory Company Name: 7layers GmbH Address: Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the FCC and accepted under the registration number 96716. This facility has been fully described in a report submitted to the IC and accepted under the registration number: Site# 3699A-1. The test facility is also accredited by the following accreditation organisation: Laboratory accreditation no: DAkkS D-PL-12140-01-00 Responsible for accreditation scope: Dipl.-Ing. Marco Kullik Report Template Version: 2016-08-19 Project Data Responsible for testing and report: Dipl.-Ing. Daniel Gall Employees who performed the tests: documented internally at 7Layers Date of Report: 2017-11-29 Testing Period: 2017-10-28 to 2017-11-08 Applicant Data Company Name: GN Audio A/S Address: Lautrupbjerg 7 DK-2750 Ballerup Denmark Contact Person: Manufacturer Data Company Name: Please see applicant data Address: Contact Person: Test report reference: MDE_GNAUD_1707_FCCd Page 5 of 24

1 Test object Data General EUT Description Equipment under Test Jabra Elite 65t OTE070 & OTE071 Type Designation: OTE070 & OTE071 Kind of Device: 10.6 MHz RF Transceiver Voltage Type: DC Voltage level: 3.7 V General product description: The EUT is a wireless headset with an ear to ear link between the left and right side earbud. The headset has a Bluetooth & Bluetooth low energy transceiver in the right earbud and a magnetic induction transceiver in both left and right earbud. The EUT provides the following ports: Port and interconnecting cables Cable length Shielded - - - The main components of the EUT are listed and described in Chapter 2. Test report reference: MDE_GNAUD_1707_FCCd Page 6 of 24

EUT Main components Type, S/N, Short Descriptions etc. used in this Test Report Short Equipment under Type Designation Serial No. HW SW Status Date of Description Test Status Receipt EUT A (Code: Jabra Elite 65t OTE070 N/A 28-04992 1.0 - DE1230005 ae01) Remarks: EUT A is equipped with an integral antenna. EUT B (Code: Jabra Elite 65t OTE071 N/A 28-05016 1.0 - DE1230005 ae01) Remarks: EUT B is equipped with an integral antenna. NOTE: The short description is used to simplify the identification of the EUT in this test report. Ancillary Equipment For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Short Equipment Type Serial No. HW Status SW FCC Description under Test Designation Status ID ‒ ‒ ‒ ‒ ‒ ‒ – Auxiliary Equipment For the purposes of this test report, auxiliary equipment is defined as equipment which is used temporarily to enable operational and control features especially used for the tests of the EUT which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Auxiliary Equipment can influence the test results. Short Equipment Type Designation Serial no. HW SW FCC Description under Test Status Status ID ‒ ‒ ‒ ‒ ‒ ‒ ‒ EUT Setups This chapter describes the combination of EUTs and equipment used for testing. The rationale for selecting the EUTs, ancillary and auxiliary equipment and interconnecting cables, is to test a representative configuration meeting the requirements of the referenced standards. Setup No. Combination of EUTs Description and Rationale Setup_01 EUT A and EUT B Test report reference: MDE_GNAUD_1707_FCCd Page 7 of 24

Operating Modes This chapter describes the operating modes of the EUTs used for testing. Op. Mode Description of Operating Modes Remarks Op-mode 1 continuous modulation EUT is transmitting continuously modulated signal Special software used for testing None Product labelling 1.8.1. FCC ID label Please refer to the documentation of the applicant. 1.8.2. Location of the label on the EUT Please refer to the documentation of the applicant. Test report reference: MDE_GNAUD_1707_FCCd Page 8 of 24

2 Test Results Spurious radiated emissions Standard FCC Part 15, Subpart C The test was performed according to: ANSI C63.10 2.1.1. Test Description The test set-up was made in accordance to the general provisions of ANSI C63.10 in a typical installation configuration. The Equipment Under Test (EUT) was set up on a non- conductive table 1.0 x 2.0 m² in the semi-anechoic chamber. The influence of the EUT support table that is used between 30–1000 MHz was evaluated. The measurement procedure is implemented into the EMI test software EMC32 from R&S. Exploratory tests are performed at 3 orthogonal axes to determine the worst-case orientation of a body-worn or handheld EUT. The final test on all kind of EUTs is also performed at 3 axes. A pre-check is performed while the EUT is powered from a DC power source. 1. Measurement up to 30 MHz The Loop antenna HFH2-Z2 is used. Step 1: pre measurement • Anechoic chamber • Antenna distance: 3 m • Detector: Peak-Maxhold • Frequency range: 0.009 - 0.15 MHz and 0.15 – 30 MHz • Frequency steps: 0.05 kHz and 2.25 kHz • IF–Bandwidth: 0.2 kHz and 9 kHz • Measuring time / Frequency step: 100 ms (FFT-based) Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: final measurement For the relevant emissions determined in step 1, an additional measurement with the following settings will be performed. Intention of this step is to find the maximum emission level. • Open area test side • Antenna distance: according to the Standard • Detector: Quasi-Peak • Frequency range: 0.009 – 30 MHz • Frequency steps: measurement at frequencies detected in step 1 • IF–Bandwidth: 0.2 - 10 kHz • Measuring time / Frequency step: 1 s 2. Measurement above 30 MHz and up to 1 GHz Step 1: Preliminary scan This is a preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Antenna distance: 3 m - Detector: Peak-Maxhold / Quasipeak (FFT-based) - Frequency range: 30 – 1000 MHz Test report reference: MDE_GNAUD_1707_FCCd Page 9 of 24

- Frequency steps: 30 kHz - IF–Bandwidth: 120 kHz - Measuring time / Frequency step: 100 ms - Turntable angle range: –180° to 90° - Turntable step size: 90° - Height variation range: 1 – 3 m - Height variation step size: 2 m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: Adjustment measurement In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency, which was determined the turntable azimuth and antenna height will be adjusted. The turntable azimuth will slowly vary by ± 45° around this value. During this action, the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position, the antenna height will also slowly vary by ± 100 cm around the antenna height determined. During this action, the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100 ms - Turntable angle range: ± 45 ° around the determined value - Height variation range: ± 100 cm around the determined value - Antenna Polarisation: max. value determined in step 1 Step 3: Final measurement with QP detector With the settings determined in step 3, the final measurement will be performed: EMI receiver settings for step 4: - Detector: Quasi-Peak (< 1 GHz) - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 1 s After the measurement a plot will be generated this contains a diagram with the results of the preliminary scan and a chart with the frequencies and values of the results of the final measurement. Test report reference: MDE_GNAUD_1707_FCCd Page 10 of 24

2.1.2. Test Requirements / Limits FCC Part 15, Subpart C, §15.209, Radiated Emission Limits Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 0.009 – 0.49 2400/F(kHz)@300m 3 (48.5 – 13.8)@300m 0.49 – 1.705 24000/F(kHz)@30m 3 (33.8 – 23.0)@30m 1.705 – 30 30@30m 3 29.5@30m The measured values are corrected with an inverse linear distance extrapolation factor (40 dB/decade) according FCC 15.31 (2). Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 30 – 88 100@3m 3 40.0@3m 88 – 216 150@3m 3 43.5@3m 216 – 960 200@3m 3 46.0@3m 960 - 26000 500@3m 3 54.0@3m 26000 - 40000 500@3m 1 54.0@3m §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) Test report reference: MDE_GNAUD_1707_FCCd Page 11 of 24

2.1.3. Test Protocol Temperature: 24 °C Air Pressure: 1012 hPa Humidity: 40 % 2.1.3.1. Measurement up to 30 MHz Op. Mode Setup Port op-mode 1 Setup_01 Enclosure Polari- Frequency Corrected value Limit Limit Limit Delta to Delta to sation MHz dBµV/m dBµV/ dBµV/ dBµV/ limit limit m m m dB dB QP Peak AV QP Peak AV QP/Peak AV – – – – – – – – – – Remark: No relevant spurious emissions in the range 20 dB below the limit found, therefore step 2 was not performed. Please see annex for the measurement plots. 2.1.3.2. Measurement above 30 MHz Op. Mode Setup Port op-mode 1 Setup_01 Enclosure Polari- Frequency Corrected value Limit Limit Limit Delta to Delta to sation MHz dBµV/m dBµV/ dBµV/ dBµV/ limit limit m m m dB dB QP Peak AV QP Peak AV QP/Peak AV – – – – – – – – – – Remarks: No relevant spurious emissions in the range 20 dB below the limit found, therefore step 2 was not performed. Please see annex for the measurement plots. 2.1.4. Test result: Spurious radiated emissions FCC Part 15, Subpart C Op. Mode Result op-mode 1 passed Test report reference: MDE_GNAUD_1707_FCCd Page 12 of 24

Peak power output Standard FCC Part 15, Subpart C The test was performed according to: ANSI C63.10 3.2.1 Test Description Please refer to sub-clause 2.1.1. 3.2.2 Test Limits Please refer to sub-clause 2.1.2. 3.2.3 Test Protocol Temperature: 24 °C Air Pressure: 1012 hPa Humidity: 40 % Op. Mode Setup Port op-mode 1 Setup_01 Enclosure Output Limit dBµV/m at Frequency power fundamental frequency Remarks MHz dBµV/m for 10 m distance Maximum radiated field strength <-8.86 10.6 - at fundamental frequency Note: The EUT transmitted a continuously modulated signal. Remark: Please see annex for the measurement plots. Comment: The Peak power output is not measurable in a distance of 3m, because the output power level is below the noise level of the testsystem, therefore no measurement value is reported. 3.2.4 Test result: Peak power output FCC Part 15, Subpart C Op. Mode Result op-mode 1 passed Test report reference: MDE_GNAUD_1707_FCCd Page 13 of 24

3 Measurement uncertainty Test Case Parameter Uncertainty Peak power output Power ± 4.5 dB Occupied bandwidth Power ± 4.5 dB Frequency: ± 0.125 kHz Spurious radiated emissions Power ± 4.5 dB Frequency: ± 11.2 kHz 4 Test equipment 1 Radiated Emissions Lab to perform radiated emission tests Ref.No. Device Name Description Manufacturer Serial Number Calibration Due 1.1 Fully Anechoic 8.80m x 4.60m x Albatross Projects P26971-647-001-PRB Room 4.05m (l x w x h) 1.2 AM 4.0 Antenna mast Maturo GmbH AM4.0/180/11920513 1.3 ESR 7 EMI Receiver / Rohde & Schwarz 101424 2018-11-29 Spectrum Analyzer 1.4 Anechoic Chamber 10.58 x 6.38 x Frankonia none 2019-05-02 6.00 m³ 1.5 ESIB 26 Spectrum Analyzer Rohde & Schwarz 830482/004 2017-12-09 1.6 Tilt device Maturo Antrieb TD1.5- Maturo GmbH TD1.5- (Rohacell) 10kg 10kg/024/3790709 1.7 AS 620 P Antenna mast HD GmbH 620/37 1.8 NRV-Z1 Sensor Head A Rohde & Schwarz 827753/005 1.9 JS4-18002600-32- Broadband Miteq 849785 5P Amplifier 18 GHz - 26 GHz 1.10 HL 562 Ultralog new Rohde & Schwarz 830547/003 2018-06-30 biconicals GmbH & Co. KG 1.11 Opus10 THI ThermoHygro Lufft Mess- und 12482 2019-03-29 (8152.00) Datalogger 12 Regeltechnik (Environ) GmbH 1.12 HFH2-Z2 Loop Antenna Rohde & Schwarz 829324/006 2017-11-27 GmbH & Co. KG 1.13 FSW 43 Spectrum Analyzer Rohde & Schwarz 103779 2018-12-02 1.14 Opus10 TPR ThermoAirpressure Lufft Mess- und 13936 2019-04-09 (8253.00) Datalogger 13 Regeltechnik (Environ) GmbH 1.15 Chroma 6404 AC Power Source Chroma ATE INC. 64040001304 1.16 3160-10 Standard Gain / EMCO Elektronik 00086675 Pyramidal Horn GmbH Antenna 40 GHz 1.17 HL 562 Ultralog Log.-per. Antenna Rohde & Schwarz 100609 2019-04-19 GmbH & Co. KG 1.18 HF 907 Double-ridged Rohde & Schwarz 102444 2018-05-11 horn GmbH & Co. KG 1.19 DE 325 Dreheinheit HD GmbH Test report reference: MDE_GNAUD_1707_FCCd Page 14 of 24

2 Radio lab Lab to perform frequency bandwidth measurements Manufacturer Serial Number Calibration Ref.No. Device Name Description Due 2.1 FSV30 Signal Analyzer Rohde & Schwarz 103005 2018-02-24 Weinschel Weinschel 2.2 10 dB attenuator W3711 - 56-10 Weinschel Weinschel 2.3 10 dB attenuator F9401 - 4T-10 2.4 WA1515 6 dB coupler Weinschel A855 - A8455-4 Rev.0 2.5 20 dB coupler - 07-00 - ST18/SMAm/ Coaxial cable 2.6 - Batch No. 12424 - SMAm/36 (RLC-1) ST18/SMAm/ Coaxial cable 2.7 - Batch No. 625905 - SMAm/36 (RLC-2) ST18/SMAm Coaxial cable 2.8 - Batch No. 625626 - /Nm/48 (RL-RX spuri cable) 2.9 7006-1 DC blocker Weinschel W0026 - DC power 2.10 NGSM 32/10 Rohde & Schwarz 2725 2019-06-22 supply Thermo- Lufft 2.11 OPUS 10 12482 2019-03-29 Hydrometer Digital Fluke 2.12 177 86670383 2018-02-03 Voltmeter Temperature Vötsch 585660021 2.13 VT4002 2018-03-08 Chamber 50010 Test report reference: MDE_GNAUD_1707_FCCd Page 15 of 24

5 Antenna Factors, Cable Loss and Sample Calculations This chapter contains the antenna factors with their corresponding path loss of the used measurement path for all antennas as well as the insertion loss of the LISN. LISN R&S ESH3-Z5 (150 kHz – 30 MHz) cable LISN loss insertion (incl. 10 loss dB ESH3- atten- Frequency Corr. Z5 uator) MHz dB dB dB 0,15 10,1 0,1 10,0 5 10,3 0,1 10,2 7 10,5 0,2 10,3 10 10,5 0,2 10,3 12 10,7 0,3 10,4 14 10,7 0,3 10,4 16 10,8 0,4 10,4 18 10,9 0,4 10,5 20 10,9 0,4 10,5 22 11,1 0,5 10,6 24 11,1 0,5 10,6 26 11,2 0,5 10,7 28 11,2 0,5 10,7 30 11,3 0,5 10,8 Sample calculation ULISN (dB µV) = U (dB µV) + Corr. (dB) U = Receiver reading LISN Insertion loss = Voltage Division Factor of LISN Corr. = sum of single correction factors of used LISN, cables, switch units (if used) Linear interpolation will be used for frequencies in between the values in the table. Test report reference: MDE_GNAUD_1707_FCCd Page 16 of 24

Antenna R&S HFH2-Z2 (9 kHz – 30 MHz) cable cable cable cable distance dLimit dused loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. AF (inside (outside (switch (to (-40 dB/ distance distance Frequency HFH-Z2) Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 0,009 20,50 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,01 20,45 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,015 20,37 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,02 20,36 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,025 20,38 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,03 20,32 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,05 20,35 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,08 20,30 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,1 20,20 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,2 20,17 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,3 20,14 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,49 20,12 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,490001 20,12 -39,6 0,1 0,1 0,1 0,1 -40 30 3 0,5 20,11 -39,6 0,1 0,1 0,1 0,1 -40 30 3 0,8 20,10 -39,6 0,1 0,1 0,1 0,1 -40 30 3 1 20,09 -39,6 0,1 0,1 0,1 0,1 -40 30 3 2 20,08 -39,6 0,1 0,1 0,1 0,1 -40 30 3 3 20,06 -39,6 0,1 0,1 0,1 0,1 -40 30 3 4 20,05 -39,5 0,2 0,1 0,1 0,1 -40 30 3 5 20,05 -39,5 0,2 0,1 0,1 0,1 -40 30 3 6 20,02 -39,5 0,2 0,1 0,1 0,1 -40 30 3 8 19,95 -39,5 0,2 0,1 0,1 0,1 -40 30 3 10 19,83 -39,4 0,2 0,1 0,2 0,1 -40 30 3 12 19,71 -39,4 0,2 0,1 0,2 0,1 -40 30 3 14 19,54 -39,4 0,2 0,1 0,2 0,1 -40 30 3 16 19,53 -39,3 0,3 0,1 0,2 0,1 -40 30 3 18 19,50 -39,3 0,3 0,1 0,2 0,1 -40 30 3 20 19,57 -39,3 0,3 0,1 0,2 0,1 -40 30 3 22 19,61 -39,3 0,3 0,1 0,2 0,1 -40 30 3 24 19,61 -39,3 0,3 0,1 0,2 0,1 -40 30 3 26 19,54 -39,3 0,3 0,1 0,2 0,1 -40 30 3 28 19,46 -39,2 0,3 0,1 0,3 0,1 -40 30 3 30 19,73 -39,1 0,4 0,1 0,3 0,1 -40 30 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -40 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values Test report reference: MDE_GNAUD_1707_FCCd Page 17 of 24

Antenna R&S HL562 (30 MHz – 1 GHz) (dLimit = 3 m) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. R&S (inside (outside (switch (to (-20 dB/ distance distance Frequency HL562 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 30 18,6 0,6 0,29 0,04 0,23 0,02 0,0 3 3 50 6,0 0,9 0,39 0,09 0,32 0,08 0,0 3 3 100 9,7 1,2 0,56 0,14 0,47 0,08 0,0 3 3 150 7,9 1,6 0,73 0,20 0,59 0,12 0,0 3 3 200 7,6 1,9 0,84 0,21 0,70 0,11 0,0 3 3 250 9,5 2,1 0,98 0,24 0,80 0,13 0,0 3 3 300 11,0 2,3 1,04 0,26 0,89 0,15 0,0 3 3 350 12,4 2,6 1,18 0,31 0,96 0,13 0,0 3 3 400 13,6 2,9 1,28 0,35 1,03 0,19 0,0 3 3 450 14,7 3,1 1,39 0,38 1,11 0,22 0,0 3 3 500 15,6 3,2 1,44 0,39 1,20 0,19 0,0 3 3 550 16,3 3,5 1,55 0,46 1,24 0,23 0,0 3 3 600 17,2 3,5 1,59 0,43 1,29 0,23 0,0 3 3 650 18,1 3,6 1,67 0,34 1,35 0,22 0,0 3 3 700 18,5 3,6 1,67 0,42 1,41 0,15 0,0 3 3 750 19,1 4,1 1,87 0,54 1,46 0,25 0,0 3 3 800 19,6 4,1 1,90 0,46 1,51 0,25 0,0 3 3 850 20,1 4,4 1,99 0,60 1,56 0,27 0,0 3 3 900 20,8 4,7 2,14 0,60 1,63 0,29 0,0 3 3 950 21,1 4,8 2,22 0,60 1,66 0,33 0,0 3 3 1000 21,6 4,9 2,23 0,61 1,71 0,30 0,0 3 3 (dLimit = 10 m) 30 18,6 -9,9 0,29 0,04 0,23 0,02 -10,5 10 3 50 6,0 -9,6 0,39 0,09 0,32 0,08 -10,5 10 3 100 9,7 -9,2 0,56 0,14 0,47 0,08 -10,5 10 3 150 7,9 -8,8 0,73 0,20 0,59 0,12 -10,5 10 3 200 7,6 -8,6 0,84 0,21 0,70 0,11 -10,5 10 3 250 9,5 -8,3 0,98 0,24 0,80 0,13 -10,5 10 3 300 11,0 -8,1 1,04 0,26 0,89 0,15 -10,5 10 3 350 12,4 -7,9 1,18 0,31 0,96 0,13 -10,5 10 3 400 13,6 -7,6 1,28 0,35 1,03 0,19 -10,5 10 3 450 14,7 -7,4 1,39 0,38 1,11 0,22 -10,5 10 3 500 15,6 -7,2 1,44 0,39 1,20 0,19 -10,5 10 3 550 16,3 -7,0 1,55 0,46 1,24 0,23 -10,5 10 3 600 17,2 -6,9 1,59 0,43 1,29 0,23 -10,5 10 3 650 18,1 -6,9 1,67 0,34 1,35 0,22 -10,5 10 3 700 18,5 -6,8 1,67 0,42 1,41 0,15 -10,5 10 3 750 19,1 -6,3 1,87 0,54 1,46 0,25 -10,5 10 3 800 19,6 -6,3 1,90 0,46 1,51 0,25 -10,5 10 3 850 20,1 -6,0 1,99 0,60 1,56 0,27 -10,5 10 3 900 20,8 -5,8 2,14 0,60 1,63 0,29 -10,5 10 3 950 21,1 -5,6 2,22 0,60 1,66 0,33 -10,5 10 3 1000 21,6 -5,6 2,23 0,61 1,71 0,30 -10,5 10 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. Test report reference: MDE_GNAUD_1707_FCCd Page 18 of 24

Antenna R&S HF907 (1 GHz – 18 GHz) cable cable loss 3 loss 1 (switch (relay + cable unit, AF cable loss 2 atten- cable R&S inside (outside uator & loss 4 (to Frequency HF907 Corr. chamber) chamber) pre-amp) receiver) MHz dB (1/m) dB dB dB dB dB 1000 24,4 -19,4 0,99 0,31 -21,51 0,79 2000 28,5 -17,4 1,44 0,44 -20,63 1,38 3000 31,0 -16,1 1,87 0,53 -19,85 1,33 4000 33,1 -14,7 2,41 0,67 -19,13 1,31 5000 34,4 -13,7 2,78 0,86 -18,71 1,40 6000 34,7 -12,7 2,74 0,90 -17,83 1,47 7000 35,6 -11,0 2,82 0,86 -16,19 1,46 cable loss 4 cable (switch loss 1 cable cable unit, used AF (relay loss 2 loss 3 atten- cable for R&S inside (inside (outside uator & loss 5 (to FCC Frequency HF907 Corr. chamber) chamber) chamber) pre-amp) receiver) 15.247 MHz dB (1/m) dB dB dB dB dB dB 3000 31,0 -23,4 0,47 1,87 0,53 -27,58 1,33 4000 33,1 -23,3 0,56 2,41 0,67 -28,23 1,31 5000 34,4 -21,7 0,61 2,78 0,86 -27,35 1,40 6000 34,7 -21,2 0,58 2,74 0,90 -26,89 1,47 7000 35,6 -19,8 0,66 2,82 0,86 -25,58 1,46 cable loss 1 cable cable cable cable cable AF (relay loss 2 loss 3 loss 4 loss 5 loss 6 R&S inside (High (pre- (inside (outside (to Frequency HF907 Corr. chamber) Pass) amp) chamber) chamber) receiver) MHz dB (1/m) dB dB dB dB dB dB dB 7000 35,6 -57,3 0,56 1,28 -62,72 2,66 0,94 1,46 8000 36,3 -56,3 0,69 0,71 -61,49 2,84 1,00 1,53 9000 37,1 -55,3 0,68 0,65 -60,80 3,06 1,09 1,60 10000 37,5 -56,2 0,70 0,54 -61,91 3,28 1,20 1,67 11000 37,5 -55,3 0,80 0,61 -61,40 3,43 1,27 1,70 12000 37,6 -53,7 0,84 0,42 -59,70 3,53 1,26 1,73 13000 38,2 -53,5 0,83 0,44 -59,81 3,75 1,32 1,83 14000 39,9 -56,3 0,91 0,53 -63,03 3,91 1,40 1,77 15000 40,9 -54,1 0,98 0,54 -61,05 4,02 1,44 1,83 16000 41,3 -54,1 1,23 0,49 -61,51 4,17 1,51 1,85 17000 42,8 -54,4 1,36 0,76 -62,36 4,34 1,53 2,00 18000 44,2 -54,7 1,70 0,53 -62,88 4,41 1,55 1,91 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. Test report reference: MDE_GNAUD_1707_FCCd Page 19 of 24

Antenna EMCO 3160-09 (18 GHz – 26.5 GHz) cable cable cable cable cable AF loss 1 loss 2 loss 3 loss 4 loss 5 EMCO (inside (pre- (inside (switch (to Frequency 3160-09 Corr. chamber) amp) chamber) unit) receiver) MHz dB (1/m) dB dB dB dB dB dB 18000 40,2 -23,5 0,72 -35,85 6,20 2,81 2,65 18500 40,2 -23,2 0,69 -35,71 6,46 2,76 2,59 19000 40,2 -22,0 0,76 -35,44 6,69 3,15 2,79 19500 40,3 -21,3 0,74 -35,07 7,04 3,11 2,91 20000 40,3 -20,3 0,72 -34,49 7,30 3,07 3,05 20500 40,3 -19,9 0,78 -34,46 7,48 3,12 3,15 21000 40,3 -19,1 0,87 -34,07 7,61 3,20 3,33 21500 40,3 -19,1 0,90 -33,96 7,47 3,28 3,19 22000 40,3 -18,7 0,89 -33,57 7,34 3,35 3,28 22500 40,4 -19,0 0,87 -33,66 7,06 3,75 2,94 23000 40,4 -19,5 0,88 -33,75 6,92 3,77 2,70 23500 40,4 -19,3 0,90 -33,35 6,99 3,52 2,66 24000 40,4 -19,8 0,88 -33,99 6,88 3,88 2,58 24500 40,4 -19,5 0,91 -33,89 7,01 3,93 2,51 25000 40,4 -19,3 0,88 -33,00 6,72 3,96 2,14 25500 40,5 -20,4 0,89 -34,07 6,90 3,66 2,22 26000 40,5 -21,3 0,86 -35,11 7,02 3,69 2,28 26500 40,5 -21,1 0,90 -35,20 7,15 3,91 2,36 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. Test report reference: MDE_GNAUD_1707_FCCd Page 20 of 24

Antenna EMCO 3160-10 (26.5 GHz – 40 GHz) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. EMCO (inside (outside (switch (to (-20 dB/ distance distance Frequency 3160-10 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) GHz dB (1/m) dB dB dB dB dB dB m m 26,5 43,4 -11,2 4,4 -15,6 3 0,5 27,0 43,4 -11,2 4,4 -15,6 3 0,5 28,0 43,4 -11,1 4,5 -15,6 3 0,5 29,0 43,5 -11,0 4,6 -15,6 3 0,5 30,0 43,5 -10,9 4,7 -15,6 3 0,5 31,0 43,5 -10,8 4,7 -15,6 3 0,5 32,0 43,5 -10,7 4,8 -15,6 3 0,5 33,0 43,6 -10,7 4,9 -15,6 3 0,5 34,0 43,6 -10,6 5,0 -15,6 3 0,5 35,0 43,6 -10,5 5,1 -15,6 3 0,5 36,0 43,6 -10,4 5,1 -15,6 3 0,5 37,0 43,7 -10,3 5,2 -15,6 3 0,5 38,0 43,7 -10,2 5,3 -15,6 3 0,5 39,0 43,7 -10,2 5,4 -15,6 3 0,5 40,0 43,8 -10,1 5,5 -15,6 3 0,5 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. 6 Photo Report Photos are included in an external report. 7 Setup Drawings Test report reference: MDE_GNAUD_1707_FCCd Page 21 of 24

Drawing 1: Setup in the Anechoic chamber. For measurements below 1 GHz the ground was replaced by a conducting ground plane. Test report reference: MDE_GNAUD_1707_FCCd Page 22 of 24

8 FCC and IC Correlation of measurement requirements for General Radio Equipment from FCC and IC General radio equipment Measurement FCC reference IC reference Conducted emissions on AC § 15.207 RSS-Gen Issue 4: 8.8 Mains Transmitter spurious radiated § 15.209 RSS-Gen Issue 4: 6.13/8.9/8.10; emissions RSS-210 Issue 8: 2.5 Spurious radiated emissions § 15.201, RSS-Gen Issue 4: 8.9/8.10; below 490 kHz and restricted CFR47, Part 2, Subpart J; RSS-210 Issue 8: 2.5.1; to emission level if all emissions ≤ 40 dB below RSS-310 Issue 3; the limit listed in §15.209 if all emissions ≤ 40 dB below the limit listed in RSS-Gen Wanted Emission (Carrier) § 15.209 RSS-210 Issue 8: 2.5.1 RSS-Gen Issue 4: 6.12, 8.9 Other requirements, e.g. §15.215 RSS- Gen, Issue 4: 6.11/8.11 Transmitter frequency stability Antenna requirement § 15.203 / 15.204 RSS-Gen Issue 4: 8.3 Receiver spurious emissions – RSS-210 Issue 8: 2.3; RSS Gen Issue 4: 5/7 *) *) Receivers are exempted from certification besides if operating in stand-alone mode in the frequency range 30–960 MHz or if these are scanner receivers. Test report reference: MDE_GNAUD_1707_FCCd Page 23 of 24

9 Annex measurement plots Radiated emissions and peak output power 9.1.1. Spurious radiated emissions up to 30 MHz – Op-Mode 1 EUT A + EUT B Level in dBµV/m 9.1.2. Spurious radiated emissions above 30 MHz – Op_Mode 1 EUT A & EUT B Test report reference: MDE_GNAUD_1707_FCCd Page 24 of 24


Document Created: 2017-11-29 16:39:30
Document Modified: 2017-11-29 16:39:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC