SAR Report Appendix C-2

FCC ID: B949260NGWM

RF Exposure Info

Download: PDF
FCCID_3671805

EX3DV4 — SN:3971 March 24, 2017 Probe EX3DV4 SN:3971 Manufactured: December 30, 2013 Calibrated: March 24, 2017 Calibrated for DASY/EASY Systems (Note: non—compatible with DASY2 system!) Certificate No: EX3—3971_Mar17 Page 3 of 11

EX3DV4— SN:3971 March 24, 2017 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3971 Basic Calibration Parameters Sensor X Sensor Y Sensor Z Unc (k=2) Norm (uV/(V/m)")* 0.40 0.50 0.48 +101 % DCP (mV)’d 101.4 99.2 100.2 Modulation Calibration Parameters UID Communication System Name A B C D VR Unc"® dB dByuV dB mV (k=2) 0 CW xX 0.0 0.0 1.0 0.00 156.0 +3.0 % Y 0.0 0.0 1.0 141.4 Z 0.0 0.0 1.0 141.6 The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * The uncertainties of Norm X,Y.Z do not affect the E"—field uncertainty inside TSL (see Pages 5 and 6). ® Numerical linearization parameter: uncertainty not required. © Uncertainty is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value. Certificate No: EX3—3971_Mar17 Page 4 of 11

EX3DV4— SN:3971 March 24, 2017 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3971 Calibration Parameter Determined in Head Tissue Simulating Media Relative Conductivity DeptF Unc f (MHz)° _|__Permittivity" (S/im)" ConvFX ConvF Y ConvFZ Aipha® _(mm) (k=2) 6 55.5 0.75 21.45 21.45 21.45 0.00 1.00 + 13.3 % 13 55.5 0.75 18.18 18.18 18.18 0.00 1.00 + 13.3 % 750 41.9 0.89 10.91 10.91 10.91 0.46 0.95 +12.0 % 835 41.5 0.90 10.67 10.67 10.67 0.40 0.95 +12.0 % 900 41.5 0.97 10.51 10.51 10.51 0.46 0.85 +12.0 % 1450 40.5 1.20 8.99 8.99 8.99 0.30 0.90 +12.0 % 1640 40.2 1.31 8.94 8.94 8.94 0.36 0.80 +12.0 % 1750 40.1 1.37 8.92 8.92 8.92 0.34 0.81 +12.0 % 1900 40.0 1.40 8.59 8.59 8.59 0.33 0.84 + 12.0 % 2000 40.0 1.40 8.54 8.54 8.54 0.33 0.84 +12.0 % 2300 39.5 1.67 8.12 8.12 8.12 0.29 0.84 + 12.0 % 2450 39.2 1.80 7.77 7.77 7.77 0.35 0.80 +12.0 % 2600 39.0 1.96 7.59 7.59 7.59 0.39 0.80 +12.0 % 5250 35.9 4.71 5.34 5.34 5.34 0.35 1.80 +131 % 5500 35.6 4.96 5.14 5.14 5.14 0.40 1.80 +13.1 % 5600 35.5 5.07 4.96 4.96 4.96 0.40 1.80 +131 % 5800 35.3 5.27 4.98 4.98 4.98 0.40 1.80 +13.1 % © Frequency validity above 300 MHz of + 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively, Above 5 GHz frequency validity can be extended to + 110 MHz. " At frequencies below 3 GHz, the validity of tissue parameters (s and &) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (e and 0) is restricted to + 5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. ® Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: EX3—3971_Mar17 Page 5 of 11

EX3DV4— SN:3971 March 24, 2017 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3971 Calibration Parameter Determined in Body Tissue Simulating Media Relative Conductivity Depth © Unc f (MHz)° Permittivity" (S/m)" ConvF X ConvFY ConvFZ Alpha® _(mm) (k=2) 750 55.5 0.96 10.61 10.61 10.61 0.49 0.80 + 12.0 % 835 55.2 0.97 10.52 10.52 10.52 0.44 0.80 +12.0 % 900 55.0 1.05 10.48 10.48 10.48 0.47 0.82 +12.0 % 1450 54.0 1.30 8.80 8.80 8.80 0.33 0.80 +12.0 % 1640 53.7 1.42 8.73 8.73 8.73 0.40 0.80 +12.0 % 1750 53.4 1.49 8.51 8.51 8.51 0.34 0.89 +12.0 % 1900 53.3 1.52 8.26 8.26 8.26 0.27 0.95 +12.0 % 2000 53.3 1.52 8.43 8.43 8.43 0.33 0.88 +12.0 % 2300 52.9 1.81 7.85 7.85 7.85 0.36 0.80 +12.0 % 2450 52.7 1.95 7.67 7.67 7.67 0.30 0.85 +12.0 % 2600 52.5 216 7.32 7.32 7.32 0.21 0.99 +12.0 % 5250 48.9 5.36 4.70 4.70 4.70 0.45 1.90 + 13.1 % 5500 48.6 5.65 4.32 4.32 4.32 0.50 1.90 £#13.1 % 5600 48.5 5.77 4.10 4.10 4.10 0.50 1.90 £13.1 % 5800 48.2 6.00 4.22 4.22 4.22 0.50 1.90 +131 % © Frequency validity above 300 MHz of + 100 MHz anly applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to + 110 MHz. " At frequencies below 3 GHz, the validity of tissue parameters (r and a) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (s and 0) is restricted to + 5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. © Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: EX3—3971_Mar17 Page 6 of 11

EX3DV4— SN:3971 March 24, 2017 Frequency Response of E—Field (TEM—Cell:ifi110 EXX, Waveguide: R22) T f j s j 20 [ a a ,e o |— *~e— _ i | 4 — | Rmme h. | g 10_ .............................................. g....:.—::f.a ...... ——arsgeicm———s se« e I ~——=€ 8 oo ! J — | 5 i=< | 8 0s—— i i | 8 0| LL— q. 742. Ti ........................................................................................................................... 0.6—/— L 0.5—— _E U | L p | L f } L OpOp O o oupop p | L O f [ 1 i j i | 0 500 1000 1500 2000 2500 3000 f [MHz] red 52 Uncertainty of Frequency Response of E—field: £ 6.3% (k=2) Certificate No: EX3—3971_Mar17 Page 7 of 11

EX3DV4— SN:3971 March 24, 2017 Receiving Pattern (¢), 9 = 0° f=600 MHz,TEM f=1800 MHz,R22 20 x & a— ~*~ >« 4 135," + 45 » *— w4 * «. & a ® ® * * a « 3 s & a + 4 ® + *» k w x—~*Wi—z + 02 it i f | *A &— * * a~"% 0 180 _ * a R # .~u *(y* 02, 04 06* a 08 f 1 **_"o2 R o4 006C + o8 «* & « , @ 44. * i. % o un oi & i0} + & t i & a l & / g y . &1 s a ® ® £ o 215 225 315 zro Pm _ — o 6 6 e # C 6 o Tot X Y Z Tot X Y Z 0 5-‘-- t 4 t a -"""“"""'i""'"““"'“"“"é-""""""'""-- |— 4 f [ray |— t I J |— ; # 5 00|# is— ow-‘-'m_w-o- is LW — 14 1i 05- ........................................................................... C 1 1 1 1 1 1 T T J 1 1 L | . L | 1 | { 1 T L 1 1 T | 1 1 T 150 100 30 6 50 100 150 Uncertainty of Axial Isotropy Assessment: £ 0.5% (k=2) Certificate No: EX3—3971_Mar17 Page 8 of 11

EX3DV4— SN:3971 March 24, 2017 Dynamic Range f(SARneaq) Input Signal [uV] (TEM cell , fevai= 1900 MHz) #5 10° SAR [mW/cm3] not compensated compensated 2 i a i 3. | s[ %oofy~ > i L —1 # “_ ; § i ffi BSF f i i3 { —2— 7 T j | 102 102 104 100 101 102 103 SAR {[mW/cm3] not compensated compensated Uncertainty of Linearity Assessment: £ 0.6% (k=2) Certificate No: EX3—3971_Mar17 Page 9 of 11

EX3DV4— SN:3971 March 24, 2017 Conversion Factor Assessment f= 835 MHz,WGLS R9 (H_convF) f= 1900 MHz,WGLS R22 (H_convF) 40 35 304 %, | a0o 0\ as C * * §°* $ ®| 3 2o 2 15 + +0 10 00 — womeg ie cugn.. o BL enc ally,l enc ts ghaFuts 4 1 0+ — adoinlmnledidcecs d bocn. d 5 10 15 20 25 30 35 40 0 & 10 15 20 25 30 35 40 2 [mm} z [mm} _8] _*® _®| _®_ analytical measured analytical measured Deviation from Isotropy in Liquid Error (¢, 8), f = 900 MHz Deviation —~1.0 —0.8 —0.6 —0.4 —0.2 0.0 0.2 0.4 0.6 08 1.0 Uncertainty of Spherical Isotropy Assessment: £ 2.6% (k=2) Certificate No: EX3—3971_Mar17 Page 10 of 11

EX3DV4— SN:3971 March 24, 2017 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3971 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) 73.4 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm Probe Body Diameter 10 mm Tip Length 9 mm Tip Diameter 2.5 mm Probe Tip to Sensor X Calibration Point 1 mm Probe Tip to Sensor Y Calibration Point 1 mm Probe Tip to Sensor Z Calibration Point 1 mm Recommended Measurement Distance from Surface 1.4 mm Certificate No: EX3—3971_Mar17 Page 11 of 11

in Collaboration with $ ~ . A 4 B {AoJ "’/ NJ r_ =‘/"/"J, a ABEW f us CNAS CADBRATION LABORAIORY To—sy \esff cmmnou Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China /,,,‘‘\.‘\ ile C CNAS LO570 Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Hittp:/www.chinattl.on Client Auden Certificate No: Z16—97206 CALIBRATION CERTIFICATE Object EX3DV4 — SN:7375 Calibration Procedure(s) FD—211—004—01 Calibration Procedures for Dosimetric E—field Probes Calibration date: December 08, 2016 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22*3)°c and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRP2 101919 27—Jun—16 (CTTL, No.J16X04777) Jun—17 Power sensor NRP—Z91 101547 27—Jun—16 (CTTL, No.J16X04777) Jun—17 Power sensor NRP—Z91 101548 27—Jun—16 (CTTL, No.J16X04777) Jun—17 Reference10dBAttenuator 18N50W—10dB 13—Mar—16(CTTL,No.J16X01547) Mar—18 Reference20dBAttenuator 18N50W—204B 13—Mar—16(CTTL, No.J16X01548) Mar—18 Reference Probe EX3DV4 SN 7307 19—Feb—16(SPEAG,No.EX3—7307_Feb16) Feb—17 DAE4 SN 1331 21—Jan—16(SPEAG, No.DAE4—1331_Jan16) Jan —17 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration SignalGeneratorMG3700A 6201052605 27—Jun—16 (CTTL, No.J16X04776) Jun—17 Network Analyzer E5071C MY46110673 26—Jan—16 (CTTL, No.J16X00894) Jan —17 Name Function Signature Calibrated by: Yu Zongying SAR Test Engineer / /’Qw% Reviewed by: Qi Dianyuan SAR Project Leader % Approved by: Lu Bingsong Deputy Director of the laboratory E/&, Mdifi; I Issued: December 09, 2016 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z16—97206 Page 1 of 11

fi ;cmlabomaonewm a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Hitp://www.chinattl.en Glossary: TSL tissue simulating liquid NORMx,y,z sensitivity in free space ConvF sensitivity in TSL / NORMx,y,z DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A,B,C,D modulation dependentlinearization parameters Polarization ® ® rotation around probe axis Polarization 0 0 rotation around an axis that is in the plane normal to probe axis (at measurement center), i 0=0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300MHz to 3GHz)", February 2005 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Methods Applied and Interpretation of Parameters: e NORMx,y,z: Assessed for E—field polarization 0=0 (fs900MHz in TEM—cell; f> 1800MHz: waveguide). NORMx,y,z are only intermediate values, i.e., the uncertainties of NORMx,y,z does not effect the E" —field uncertainty inside TSL (see below ConvF). e NORM(A)x,y,z = NORMx,y,z* frequency_response (see Frequency Response Chart). This linearization is implemented in DASY4 software versions later than 4.2. The uncertainty of the frequency response is included in the stated uncertainty of ConvF. e DCPx,y,z: DCP are numerical linearization parameters assessed based on the data of power sweep (no uncertainty required). DCP does not depend on frequency nor media. e PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on the signal characteristics. e Ax,y,z; Bx,y.z; Cx,y,z;VRxX,y,z:A,B,C are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. e ConvF and Boundary Effect Parameters: Assessed in flat phantom using E—field (or Temperature Transfer Standard for f<800MHz) and inside waveguide using analytical field distributions based on power measurements for f >800MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty valued are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx,y,z* ConvF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent ConvF is used in DASY version 4.4 and higher which allows extending the validity from+50MHz to+100MHz. e Spherical isotropy (3D deviation from isotropy): in a field of low gradients realized using a flat phantom exposed by a patch antenna. e Sensor Offset: The sensor offset corresponds to the offset of virtual measurement center from the probe tip (on probe axis). No tolerance required. e Connector Angle: The angle is assessed using the information gained by determining the NORMx (no uncertainty required). Certificate No: Z16—97206 Page 2 of 11

In Collaboration with w TTL a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail; cttl@chinattl.com Hitp://www.chinattl.on Probe EX3DV4 SN: 7375 Calibrated: December 08, 2016 Calibrated for DASY/EASY Systems (Note: non—compatible with DASY2 system!) Certificate No: Z16—97206 Page 3 of11

In Collaboration with TTL CALIBRATION a LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Hitp://www.chinattl.on DASY/EASY — Parameters of Probe: EX3DV4 — SN: 7375 Basic Calibration Parameters Sensor X Sensor Y Sensor Z Unc (k=2) Norm(uV/(V/im)) A 0.52 0.42 0.46 £10.8% DCP(mV)® 99.7 98.3 100.7 Modulation Calibration Parameters UID Communication A B 6 D VR Unc® System Name dB dB/uV dB mV (k=2) 0 Cw X 0.0 0.0 1.0 0.00 195.6 £2.4% Y 0.0 0.0 1.0 177.1 2 0.0 0.0 1.0 187.8 The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. * The uncertainties of Norm X, Y, Z do not affect the E*—field uncertainty inside TSL (see Page 5 and Page 6). ® Numerical linearization parameter: uncertainty not required. & Uncertainly is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value. Certificate No: Z16—97206 Page 4 of 11

{”’2 l;Collaboranonewim a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Hitp://www.chinattl.en DASY/EASY — Parameters of Probe: EX3DV4 — SN: 7375 Calibration Parameter Determined in Head Tissue Simulating Media — 10. 6 f [MHz]® Pefri|i:ttil\\:;y ¢ Con(:;;:r:\)n:y ConvF X ConvF Y ConvF Z Alpha® D(:’:) :(’:;t) 750 41.9 0.89 9.90 9.90 9.90 0.40 0.75 +12% 835 41.5 0.90 9.73 9.73 9.73 0.15 1.41 +12% 900 41.5 0.97 9.78 9.78 9.78 9.16 1.43 £12% 1750 40.1 1.37 8.31 8.31 8.31 0.30 0.95 +12% 1900 40.0 1.40 7.92 7.92 7.92 0.25 1.04 +12% 2000 40.0 1.40 7.99 7.99 7.99 0.26 1.04 £12% 2100 39.8 1.49 8.30 8.30 8.30 0.32 0.92 £12% 2300 39.5 1.67 7.57 1.97 1.57 0.32 1.02 +12% 2450 39.2 1.80 7.27 7.27 7.27 0.38 1.01 +12% 2600 39.0 1.96 7.25 7.25 7.26 0.49 0.81 +12% 3500 37.9 2.91 7.01 7.01 7.01 0.38 1122 £15% 5200 36.0 4.66 5.58 5.58 5.58 0.36 1.55 +13% 5300 35.9 4.76 5.31 5.31 5.31 0.36 1.55 +13% 5500 35.6 4.96 5.09 5.09 5.09 0.36 1.55 £13% 5600 35.5 5.07 4.79 4.79 4.179 0.36 1.68 +13% 5800 35.3 5.27 4.78 4.78 4.78 0.40 1.65 +13% & Frequency validity above 300 MHz of +100MHz only applies for DASY v4.4 and higher (Page 2), else it is restricted to #50MHz. The uncertainty is the RSS of ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to + 110 MHz. "At frequency below 3 GHz, the validity of tissue parameters (¢ and 0) can be relaxed to £10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (€ and 0) is restricted to £5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. ©Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for the frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: Z16—97206 Page 5 of11

In Collaboration with TTL § p_ e a@ q CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Hittp:/www.chinattl.en DASY/EASY — Parameters of Probe: EX3DV4 — SN: 7375 Calibration Parameter Determined in Body Tissue Simulating Media — . = f [MHz]® Pe'::lliat‘:il\\l,i(:yF c°"‘:;7:1“)":y ConvF X ConvF Y ConvF Z Alpha® D(::’:) (L::zt) 750 555 0.96 9.94 994 994 030 0.85 +12% 835 552 0.97 9.94 994 994 015 150 +12% 900 55.0 1.05 9.89 a89 ass or 122 +12% 1750 534 1.49 8.22 822 822 o23 112 +12% 1900 53.3 1.52 7.62 T62 762 on8 124 +12% 2000 53.3 1.52 7.90 790 790 o16 1.62 £12% 2100 53.2 1.62 817 817 817 017 175 +12% 2300 52.9 1.81 7.43 7as3 743 045 0.95 +12% 2450 52.7 1.95 7.33 733 733 033 122 +12% 2600 525 216 716 716 716 048 092 £12% 3500 51.3 3.31 6.52 652 652 044 133 +13% 5200 49.0 5.30 482 as2 482 045 1.50 £13% 5300 48.9 5.42 4.57 as? 457 045 1.50 £13% 5500 48.6 5.65 aro 420 420 048 1.60 +13% 5600 485 5.77 3.99 399 399 050 1.65 +13% 5800 482 6.00 aos 408 408 055 195 £13% & Frequency validity above 300 MHz of £100MHz only applies for DASY v4.4 and higher (Page 2), else it is restricted to *50MHz. The uncertainty is the RSS of ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to + 110 MHz. "At frequency below 3 GHz, the validity of tissue parameters (e and 0) can be relaxed to £10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (€ and 0) is restricted to £5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. ©Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for the frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: Z16—97206 Page 6 of 11

fi ;Coflaborationewi'm a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Hitp://www.chinattl.en Frequency Response of E—Field (TEM—Cell: ifi110 EXX, Waveguide: R22) 1.5 7 1.44‘... Frequency response (normalized) 1.3 |.— 121. 140. 10| o. |... §B8—L—— 0.5 oc T T T T T 0 500 1000 1500 2000 2500 3000 E*—3 fIMHz _ TEM MH) . Uncertainty of Frequency Response of E—field: £7.5% (k=2) Certificate No: Z16—97206 Page 7 of 11

In Collaboration with TTL a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Hitp:/www.chinattl.en Receiving Pattern (®), 0=0° f=600 MHz, TEM f=1800 MHz, R22 1a0 [~— 0.5 os,yeacactmintfrode. . ErrofdB] 0.0 *Tedcbe.pleg. 4# Cb porg oge—a+# —0.5 —1.0 I T um * T I T T —150 —100 —50J so 100 150 Rollf*] [{—*»—1100MHz «__600MHz + 1800MHz +— 2500MHz Uncertainty of Axial Isotropy Assessment: £0.9% (k=2) Certificate No: Z16—97206 Page 8 of 11

In Collaboration with TTL a_ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail; cttl@chinattl.com Hitp://www.chinattl.en Dynamic Range f(SARneaq) (TEM cell, f= 900 MHz) 10° 4 dousks io £» e at444+ 10° 4 s 1964 C £ 9 — 1 — 4& 10‘ .s 4 £ 10° 4 10° 10 10° 10‘ 10° 10° SAR[mW/cm*] [—MO)not compensated —@— compensated 1 4 a > O ? % o h u . 1 4 .. m 2+ + ++ f—fHHPbH———i—i—t—ppbpq. it ; +H——i———iH—+rmh 10° 10° 1 o° , 10 10° 10° SAR[mW/cm | —s— not compensated —®— compensated __| Uncertainty of Linearity Assessment: £0.9% (k=2) Certificate No: Z16—97206 Page 9 of 11

4Wl in Collaboration with a=‘/"["/ §a e _a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail; cttl@chinattl.com Hitp:/www.chinattl.en Conversion Factor Assessment f=900 MHz, WGLS R9(H_convF) f=1750 MHz, WGLS R22(H_convF) W qo p og B 4o ———; t 350 | | | f 25.00 4 j a0 | | f z00 |—& & 2s a * o g‘ .h S 20 | 3 is00 |—e—. — a use | & ‘i_ ; 10.00 — 1.00 ‘ 5.00 050 : coo C ‘ a oo ‘ 0 20 40 so 80 100 9 10 2o % 40 800 s0 To 2{mm] zimim] |__—®—measured ——analytical —*+—measured __—— analytica Deviation from Isotropy in Liquid 08 0.6 04 0.2 7 Axis 0.0 —0.2 —0 4 —06 —0.8 .18 * 19 200 4«\'/;9 250 10 .Gao .Gso 040 .020 0 D20 040 060 080 10 Uncertainty of Spherical Isotropy Assessment: £2.8% (K=2) Certificate No: Z16—97206 Page 10 of 11

fi ;Collaborationewith 3 CALIBRATION LABORATORY Add: No.31 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Hitp:/www.chinattl.en DASY/EASY — Parameters of Probe: EX3DV4 — SN: 7375 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) 16.3 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disable Probe Overall Length 337mm Probe Body Diameter 10mm Tip Length 9mm Tip Diameter 2.5mm Probe Tip to Sensor X Calibration Point 1mm Probe Tip to Sensor Y Calibration Point 1imm Probe Tip to Sensor Z Calibration Point 1imm Recommended Measurement Distance from Surface 1.4mm Certificate No: Z16—97206 Page 11 of 11


Document Created: 2017-12-08 10:27:27
Document Modified: 2017-12-08 10:27:27
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC