Test Report

FCC ID: B4HBPK1900

Test Report

Download: PDF
FCCID_1637922

FCC PART 15D MEASUREMENT AND TEST REPORT For PORTA PHONE CO., INC. 145 Dean Knauss Drive, Narragansett, RI 02882, USA FCC ID: B4HBPK1900 Report Type: Product Type: Original Report DECT Transceiver Test Engineer: Felix Li Report Number: RSZ120106801-00A1 Report Date: 2012-02-14 Alvin Huang Reviewed By: EMC Engineer Test Laboratory: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn Note: This test report is prepared for the customer shown above and for the equipment described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Shenzhen). This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “★” (Rev.2)

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................................................3 OBJECTIVE ...................................................................................................................................................................3 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................3 TEST METHODOLOGY ..................................................................................................................................................3 TEST FACILITY .............................................................................................................................................................3 SYSTEM TEST CONFIGURATION..........................................................................................................................5 DESCRIPTION OF TEST CONFIGURATION ......................................................................................................................5 EQUIPMENT MODIFICATIONS .......................................................................................................................................5 LOCAL SUPPORT EQUIPMENT LIST AND DETAILS ........................................................................................................5 CONFIGURATION OF TEST SETUP .................................................................................................................................5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................6 SUMMARY OF TEST RESULTS ...............................................................................................................................7 FCC §15. 319 (I) & §2.1093 - RF EXPOSURE ...........................................................................................................8 APPLICABLE STANDARD ..............................................................................................................................................8 FCC §15.317 & §15.203 - ANTENNA REQUIREMENT ..........................................................................................9 APPLICABLE STANDARD ..............................................................................................................................................9 ANTENNA CONNECTOR CONSTRUCTION ......................................................................................................................9 FCC §15.323 (A) - EMISSION BANDWIDTH.........................................................................................................10 APPLICABLE STANDARD ............................................................................................................................................10 TEST RESULTS ...........................................................................................................................................................10 FCC §15.319 (C) - PEAK TRANSMIT POWER......................................................................................................11 APPLICABLE STANDARD ............................................................................................................................................11 TEST RESULTS ...........................................................................................................................................................11 FCC §15.319 (D) - POWER SPECTRAL DENSITY ...............................................................................................12 APPLICABLE STANDARD ............................................................................................................................................12 TEST RESULTS ...........................................................................................................................................................12 FCC §15.323 (D) - EMISSION INSIDE AND OUTSIDE THE SUB-BAND..........................................................13 APPLICABLE STANDARD ............................................................................................................................................13 TEST RESULTS ...........................................................................................................................................................13 FCC §15.319 (G) - RADIATED SPURIOUS EMISSIONS......................................................................................14 MEASUREMENT UNCERTAINTY ..................................................................................................................................14 EUT SETUP ................................................................................................................................................................14 EMI TEST RECEIVER & SPECTRUM ANALYZER SETUP ..............................................................................................15 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................15 TEST PROCEDURE ......................................................................................................................................................15 CORRECTED AMPLITUDE & MARGIN CALCULATION .................................................................................................16 TEST RESULTS SUMMARY ..........................................................................................................................................16 TEST DATA ................................................................................................................................................................16 FCC §15.323 (F) - FREQUENCY STABILITY........................................................................................................21 APPLICABLE STANDARD ............................................................................................................................................21 TEST RESULTS ...........................................................................................................................................................21 FCC §15.323 (C)(E) & §15.319(F) – SPECIFIC REQUIREMENTS FOR UPCS DEVICE.................................22 FCC Part 15D Page 2 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 GENERAL INFORMATION Product Description for Equipment Under Test (EUT) The PORTA PHONE CO., INC.’s product, model: BPK1000 (FCC ID: B4HBPK1900) or the "EUT" as referred to in this report is an earphone of FULL DUPLEX WIRELESS COMMUNICATION SYSTEM, Which measures approximately: 11.5 cm (L) x 8 cm (W) x 5 cm (H), input voltage: DC 3.7V battery. * All measurement and test data in this report was gathered from production sample serial number: 1201001 (Assigned by BACL, Shenzhen). The EUT was received on 2012-01-06. Objective This document is a test report based on the Electromagnetic Interference (EMI) tests performed on the EUT. The EMI measurements were performed according to the measurement procedure described in ANSI C63.17 - 2006, and ANSI C64.3 2009. The tests were performed in order to determine compliance with FCC Part 15, Subpart D, and section 15.203, 15.315, 15.317, 15.319 and 15.323 rules. The current device has the exactly same RF module as the original approved device (model: ComStar S, ComStar Sx, ComStar D, ComStar Dx, FCC ID: B4HDST1900) except for the layout of digital portions are different, the modifications do not affect the RF characteristics. Based on the engineering justification, the radiated emissions have been investigated, the original test results can be represented for the current device. Related Submittal(s)/Grant(s) FCC ID: B4HDST1900. Test Methodology All measurements contained in this report were conducted with ANSI C63.17 - 2006, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. All radiated and conducted emissions measurement was performed at Bay Area Compliance Laboratories Corp. (Shenzhen). The radiated testing was performed at an antenna-to-EUT distance of 3 meters. Test Facility The Test site used by Bay Area Compliance Laboratories Corp. (Shenzhen) to collect test data is located on the 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China. Test site at Bay Area Compliance Laboratories Corp. (Shenzhen) has been fully described in reports submitted to the Federal Communication Commission (FCC). The details of these reports have been found to be in compliance with the requirements of Section 2.948 of the FCC Rules on December 06, 2010. The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C63.4-2009. FCC Part 15D Page 3 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 The Federal Communications Commission has the reports on file and is listed under FCC Registration No.: 382179. The test site has been approved by the FCC for public use and is listed in the FCC Public Access Link (PAL) database. Additionally, Bay Area Compliance Laboratories Corp. (Shenzhen) is an ISO/IEC 17025 accredited laboratory, and is accredited by National Voluntary Laboratory Accredited Program (Lab Code 200707-0). The current scope of accreditations can be found at http://ts.nist.gov/Standards/scopes/2007070.htm FCC Part 15D Page 4 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 SYSTEM TEST CONFIGURATION Description of Test Configuration The system was configured for testing in TBR6 mode which is provided by the manufacturer. Equipment Modifications The conducted items were tested under TBR6 mode. Local Support Equipment List and Details Manufacturer Description Model Serial Number Digital Radio- Communication R&S CMD60 829902/026 Tester Configuration of Test Setup Antenna CMD 60 EUT FCC Part 15D Page 5 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 Block Diagram of Test Setup Antenna CMD60 AC Power 1.0 Meter EUT Non-Conductive Table 80 cm above Ground Plane 1.5 Meter FCC Part 15D Page 6 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 SUMMARY OF TEST RESULTS FCC Rules Description of Test Result § 15.319 (i), §2.1093 RF Exposure Info Compliance § 15.317, § 15.203 Antenna Requirement Compliance § 15.315, § 15.207 AC Line Conducted Emission N/A* § 15.323 (a) Emission Bandwidth Compliance* § 15.319 (c) Peak Transmit Power Compliance* § 15.319 (d) Power Spectral Density Compliance* § 15.323 (d) Emission Inside and Outside the sub-band Compliance* § 15.319 (g) Radiated Emission Compliance § 15.323 (f) Frequency Stability Compliance* § 15.323 (c)(e) Specific Requirements for UPCS § 15.319 (f) Compliance* Note: 1. N/A*, EUT is battery operation. 2. Compliance*, please refer to FCC ID: B4HDST1900. FCC Part 15D Page 7 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 FCC §15. 319 (i) & §2.1093 - RF EXPOSURE Applicable Standard According to FCC §15.319 (i) Unlicensed PCS devices are subject to the radiofrequency radiation exposure requirements specified in §§ 1.1307(b), 2.1091 and 2.1093 of this chapter, as appropriate. All equipment shall be considered to operate in a ‘‘general population/uncontrolled’’ environment. Applications for equipment authorization of devices operating under this section must contain a statement confirming compliance with these requirements for both fundamental emissions and unwanted emissions. Technical information showing the basis for this statement must be submitted to the Commission upon request. According to KDB 447498 D01 Mobile Portable RF Exposure v041) c): Unless excluded by specific FCC test procedures, portable devices with output power is ≤ 60/f(GHz) mW shall include SAR data for equipment approval. RF Exposure Evaluation Max peak output power: 18.63 dBm = 72.95 mw Antenna Gain: 2.0 dBi EIRP = 18.63 + 2.0 = 20.63 dBm = 115.61 mw The time-based average power = 115.62 mw/12 = 9.63 mW SAR exclusion threshold: 60/f(GHz) = 60/1.921536 = 31.23 mW The source-based average power of EUT is less than the threshold; the SAR evaluation can be exempted. FCC Part 15D Page 8 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 FCC §15.317 & §15.203 - ANTENNA REQUIREMENT Applicable Standard According to FCC §15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. Antenna Connector Construction This product has two integrated antennas arrangement; please refer to the internal photos. The maximum gains is 2.0 dBi, fulfill the requirement of this section. Result: Compliance. FCC Part 15D Page 9 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 FCC §15.323 (a) - EMISSION BANDWIDTH Applicable Standard The emission bandwidth is measured in accordance with ANSI C63.17 sub-clause 6.1.3 using the setup below Test Setup : EUT Attenuator Combiner/ CMD60 Splitter Test Receiver The width, in Hz, of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, that is 26 dB down relative to the maximum level of the modulated carrier. It is based on the use of measurement instrumentation employing a peak detector function with an instrument resolution bandwidth approximately equal to 1% of the emission band-width of the device under measurement. [Extraction from 47 CFR 15, subpart D, 15.303 (C)]. Test Results Please refer to FCC ID: B4HDST1900 which was granted on 2011-04-08. FCC Part 15D Page 10 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 FCC §15.319 (c) - PEAK TRANSMIT POWER Applicable Standard The peak power output as measured over an interval of time equal to the transmission-burst duration of the device under all conditions of modulation. [47 CFR 15, subpart D, 15.303 (f)]. Part 15.323(a) & Part 15.319(c) Peak Transmit Power: The limit for Peak Transmit Power (PTP) is calculated using the following formula: PTP = 100μW x (EBW) 1/2 EBW is the transmit emission bandwidth in Hz determined in the other test item: EBW = 1392000 Hz PTP = 100μW x (1392000)1/2 = 20.72 dBm The peak transmitter power is measured in accordance with ANSI C63.17-2006 Clause 6.1.2. Test Results Please refer to FCC ID: B4HDST1900 which was granted on 2011-04-08. FCC Part 15D Page 11 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 FCC §15.319 (d) - POWER SPECTRAL DENSITY Applicable Standard The average pulse energy in a 3 kHz bandwidth is divided by the pulse duration. The power spectral density shall not exceed 3 mW in any 3 kHz bandwidth as measured with a spectrum analyzer having a resolution bandwidth of 3 kHz. The power spectral density is measured in accordance with ANSI C63.17.2006 Clause 6.1.5. Test Results Please refer to FCC ID: B4HDST1900 which was granted on 2011-04-08. FCC Part 15D Page 12 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 FCC §15.323 (d) - EMISSION INSIDE AND OUTSIDE THE SUB-BAND Applicable Standard Emissions inside the sub-band must comply with the following emission mask: 1. In the bands between 1B and 2B measured from the center of the emission bandwidth the total power emitted by the device shall be at least 30 dB below the transmit power permitted for that device; 2. in the bands between 2B and 3B measured from the center of the emission bandwidth the total power emitted by an intentional radiator shall be at least 50 dB below the transmit power permitted for that radiator; 3. in the bands between 3B and the sub-band edge the total power emitted by an intentional radiator in the measurement bandwidth shall be at least 60 dB below the transmit power permitted for that radiator. Where B = emission bandwidth Emission Outside the sub-band shall be attenuated below a reference power of 112 mw (20.5 dBm) as follows: 1. 30 dB between the sub-band and 1.25 MHz above or below the sub-band; 2. 50 dB between 1.25 and 2.5 MHz above or below the sub-band; 3. 60 dB at 2.5 MHz or greater above or below the sub-band. Test Results Please refer to FCC ID: B4HDST1900 which was granted on 2011-04-08. FCC Part 15D Page 13 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 FCC §15.319 (g) - RADIATED SPURIOUS EMISSIONS Measurement Uncertainty All measurements involve certain levels of uncertainties, especially in field of EMC. The factors contributing to uncertainties are spectrum analyzer, cable loss, antenna factor calibration, antenna directivity, antenna factor variation with height, antenna phase center variation, antenna factor frequency interpolation, measurement distance variation, site imperfections, mismatch (average), and system repeatability. Based on CISPR 16-4-4, The Treatment of Uncertainty in EMC Measurements, the best estimate of the uncertainty of a radiation emissions measurement at Bay Area Compliance Laboratories Corp. (Shenzhen) is 4.0 dB (k=2, 95% level of confidence). EUT Setup The radiated emission tests were performed in the 3 meters chamber B test site, using the setup accordance with the ANSI C63.17 - 2006. The specification used was the FCC 15.209 and FCC 15.319(g) limits. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. FCC Part 15D Page 14 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 EMI Test Receiver & Spectrum Analyzer Setup The system was investigated from 30 MHz to 20 GHz. During the radiated emission test, the EMI test receiver & Spectrum Analyzer Setup were set with the following configurations: Frequency Range RBW Video B/W 30 MHz – 1000 MHz 100 kHz 300 kHz 1000 MHz – 20 GHz 1 MHz 3 MHz PK 1000 MHz – 20 GHz 1 MHz 10 Hz Ave. Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date HP Amplifier HP8447D 2944A09795 2011-08-02 2012-08-01 Rohde & Schwarz EMI Test Receiver ESCI 100035 2011-11-11 2012-11-10 Sunol Sciences Broadband Antenna JB1 A040904-1 2011-03-11 2012-03-10 Mini-Circuits Amplifier ZVA-213+ T-E27H 2011-03-08 2012-03-07 Sunol Sciences Horn Antenna DRH-118 A052604 2011-05-05 2012-05-04 Rohde & Schwarz Signal Analyzer FSIQ 26 609358 2011-07-08 2012-07-07 Agilent Spectrum Analyzer 8564E 3943A01781 2011-04-12 2012-04-11 the electro- Horn Antenna 3116 9510-2270 2011-05-05 2012-05-04 Mechanics Co. * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to NVLAP requirements, traceable to the NIST. Test Procedure For the radiated emissions test, the EUT was powered by battery. Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all installation combinations. Data was recorded in Quasi-peak detection mode for frequency range of 30 MHz-1 GHz and peak and Average detection modes for frequencies above 1 GHz. FCC Part 15D Page 15 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Loss, and subtracting the Amplifier Gain from the Meter Reading. The basic equation is as follows: Corrected Amplitude = Meter Reading + Antenna Factor + Cable Loss- Amplifier Gain The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of 7 dB means the emission is 7 dB below the maximum limit. The equation for margin calculation is as follows: Margin = Limit - Corrected Amplitude Test Results Summary According to the recorded data in following table, the EUT complied with the FCC 15.209 and 15.319 (g), with the worst margin reading of: 1.64 dB at 9642.24 MHz in the Vertical polarization (High channel) Test Data Environmental Conditions Temperature: 20 ° C Relative Humidity: 50 % ATM Pressure: 100.0 kPa The testing was performed by Felix Li on 2012-01-11 FCC Part 15D Page 16 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 1) 30-1000 MHz: Test Mode: Transmitting 80 70 60 Level in dB¦ÌV/m 50 40 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz Corrected Antenna Antenna Turntable Correction Frequency Limit Margin Amplitude Height Polarity Position Factor (MHz) (dBµV/m) (dB) (dBµV/m) (cm) (H/V) (deg) (dB) 957.760500 35.9 223.0 H 351.0 0.8 46.0 10.1 409.593250 28.1 104.0 H 50.0 -9.8 46.0 17.9 30.006868 20.3 104.0 V 54.0 -5.4 40.0 19.7 831.175000 25.4 104.0 V 6.0 -1.4 46.0 20.6 35.763250 18.1 376.0 V 270.0 -9.7 40.0 21.9 52.076000 17.5 400.0 H 71.0 -17.6 40.0 22.5 FCC Part 15D Page 17 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 2) Above 1GHz: S.A. Test Antenna Cable Pre- Cord. FCC Part 15.319/209/15.205 Freq. Detector Direction Amp. Reading Loss Amp. (MHz) PK/QP/Ave Degree Height Polar Factor Gain Limit Margin (dBµV) (dB) (dBµV/m) Remarks (m) (H/V) (dB/m) (dB) (dBµV/m) (dB) Low Channel 11529.216 49.97 PK 175 1.6 H 38.9 6.69 26.28 69.28 74 4.72 Harmonic 11529.216 50.33 PK 120 1.7 V 38.2 6.69 26.28 68.94 74 5.06 Harmonic 3855.821 59.55 PK 190 1.5 V 31.6 3.73 26.87 68.01 74 5.99 Harmonic 9643.603 51.34 PK 190 1.6 V 37.1 5.98 26.42 68.00 74 6.00 Harmonic 9643.603 48.79 PK 116 1.2 H 37.5 5.98 26.42 65.85 74 8.15 Harmonic 3855.821 56.71 PK 213 1 H 31.8 3.73 26.87 65.37 74 8.63 Harmonic 7714.026 50.94 PK 120 1.8 V 35.6 5.27 26.64 65.17 74 8.83 Harmonic 5785.993 49.73 PK 87 1.6 V 33.4 4.57 26.68 61.02 74 12.98 Harmonic 5785.993 47.18 PK 110 1.4 H 33.9 4.57 26.68 58.97 74 15.03 Harmonic 7714.026 44.00 PK 90 1.4 H 36.1 5.27 26.64 58.73 74 15.27 Harmonic Middle Channel 3850.050 61.75 PK 173 1.7 V 31.6 3.73 26.87 70.21 74 3.79* Harmonic 9624.96 52.52 PK 140 1.3 V 37.1 5.98 26.42 69.18 74 4.82 Harmonic 11549.942 49.39 PK 200 1 H 38.9 6.69 26.28 68.70 74 5.30 Harmonic 11549.942 49.55 PK 130 1.7 V 38.2 6.69 26.28 68.16 74 5.84 Harmonic 9624.96 48.35 PK 120 1.3 H 37.5 5.98 26.42 65.41 74 8.59 Harmonic 7699.968 49.57 PK 140 1.8 V 35.6 5.27 26.64 63.80 74 10.20 Harmonic 3850.050 55.04 PK 220 1.5 H 31.8 3.73 26.87 63.70 74 10.30 Harmonic 5774.976 49.28 PK 10 1 V 33.4 4.57 26.68 60.57 74 13.43 Harmonic 7699.968 45.71 PK 166 1.1 H 36.1 5.27 26.64 60.44 74 13.56 Harmonic 5774.976 47.10 PK 120 1.7 H 33.9 4.57 26.68 58.89 74 15.11 Harmonic High Channel 9642.24 52.90 PK 140 1.7 V 39.9 5.98 26.42 72.36 74 1.64* Harmonic 9642.24 51.21 PK 120 1.3 H 41.1 5.98 26.42 71.87 74 2.13* Harmonic 3856.896 61.88 PK 185 1.5 V 33.0 3.73 26.87 71.74 74 2.26* Harmonic 11570.688 49.42 PK 200 1.5 H 41.0 6.69 26.28 70.83 74 3.17* Harmonic 11570.688 49.54 PK 130 1.7 V 40.4 6.69 26.28 70.35 74 3.65* Harmonic 3856.896 58.48 PK 275 2.1 H 33.9 3.73 26.87 69.24 74 4.76 Harmonic 5785.344 51.27 PK 162 1.6 V 36.2 4.57 26.68 65.36 74 8.64 Harmonic 7686.863 48.76 PK 140 1.5 V 37.7 5.27 26.64 65.09 74 8.91 Harmonic 7686.863 46.23 PK 161 1.6 H 39.0 5.27 26.64 63.86 74 10.14 Harmonic 5785.344 47.50 PK 120 1.0 H 37.4 4.57 26.68 62.79 74 11.21 Harmonic *Within measurement uncertainty! FCC Part 15D Page 18 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 Field Strength of Radiated Emission (Average) Peak Part 15.319/209/15.205 Antenna Duty Cycle Cord. Freq. Cord. Amp. Polar Factor Amp. Limit Margin Comment (MHz) @ 3m (H/V) (dB) (dBμV/m) (dBμV/m) (dB) (dBμV/m) Low Channel 11529.216 69.28 H -27.83 41.45 54 12.55 Harmonic 11529.216 68.94 V -27.83 41.11 54 12.89 Harmonic 3855.821 68.01 V -27.83 40.18 54 13.82 Harmonic 9643.603 68.00 V -27.83 40.17 54 13.83 Harmonic 9643.603 65.85 H -27.83 38.02 54 15.98 Harmonic 3855.821 65.37 H -27.83 37.54 54 16.46 Harmonic 7714.026 65.17 V -27.83 37.34 54 16.66 Harmonic 5785.993 61.02 V -27.83 33.19 54 20.81 Harmonic 5785.993 58.97 H -27.83 31.14 54 22.86 Harmonic 7714.026 58.73 H -27.83 30.90 54 23.10 Harmonic Middle Channel 3850.050 70.21 V -27.83 42.38 54 11.62 Harmonic 9624.96 69.18 V -27.83 41.35 54 12.65 Harmonic 11549.942 68.70 H -27.83 40.87 54 13.13 Harmonic 11549.942 68.16 V -27.83 40.33 54 13.67 Harmonic 9624.96 65.41 H -27.83 37.58 54 16.42 Harmonic 7699.968 63.80 V -27.83 35.97 54 18.03 Harmonic 3850.050 63.70 H -27.83 35.87 54 18.13 Harmonic 5774.976 60.57 V -27.83 32.74 54 21.26 Harmonic 7699.968 60.44 H -27.83 32.61 54 21.39 Harmonic 5774.976 58.89 H -27.83 31.06 54 22.94 Harmonic High Channel 11570.688 70.83 H -27.83 43.00 54 8.31 Harmonic 11570.688 70.35 V -27.83 42.52 54 9.13 Harmonic 9642.24 71.87 H -27.83 44.04 54 12.67 Harmonic 7686.863 63.86 H -27.83 36.03 54 14.92 Harmonic 5785.344 62.79 H -27.83 34.96 54 15.87 Harmonic 9642.24 72.36 V -27.83 44.53 54 16.25 Harmonic 7686.863 65.09 V -27.83 37.26 54 16.89 Harmonic 3856.896 69.24 H -27.83 41.41 54 21.57 Harmonic 5785.344 65.36 V -27.83 37.53 54 21.74 Harmonic 3856.896 71.74 V -27.83 43.91 54 25.97 Harmonic Note: Duty Cycle=Ton/Tp*100% Ton=410µs =0.41ms, Tp=10.11ms Duty Cycle=4.06% Duty cycle factor = 20lg (Duty Cycle) = -27.83 dB Average = Peak + Duty Cycle Factor FCC Part 15D Page 19 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 Ton: RBW 1 MHz Delta 1 [T1 ] * VBW 3 MHz -0.39 dB Ref 25 dBm * Att 30 dB SWT 2.5 ms 410.000000 µs Offset 5 dB Marker 1 [T1 ] 20 -51.58 dBm 1.290000 ms A SGL 1 PK 10 MAXH LVL 0 -10 -20 -30 3DB AC -40 1 1 -50 -60 -70 Center 1.924992 GHz 250 µs/ 9 20 02 8 Tp : RBW 1 MHz Delta 1 [T1 ] * VBW 3 MHz 1.50 dB Ref 25 dBm * Att 30 dB SWT 50 ms 10.110000 ms Offset 5 dB Marker 1 [T1 ] 20 -50.30 dBm 16.090000 ms A SGL 1 PK 10 MAXH LVL 0 -10 -20 -30 3DB AC -40 1 1 -50 -60 -70 Center 1.924992 GHz 5 ms/ 9 20 02 3 0 FCC Part 15D Page 20 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 FCC §15.323 (f) - FREQUENCY STABILITY Applicable Standard Per FCC §15.323(f), the frequency stability of the carrier frequency of the intentional radiator shall be maintained within ±10 ppm over 1 hour or the interval between channel access monitoring, whichever is shorter. The frequency stability shall be maintained over a temperature variation of −20° to +50 °C at normal supply voltage, and over a variation in the primary supply voltage of 85 percent to 115 percent of the rated supply voltage at a temperature of 20 °C. For equipment that is capable only of operating from a battery, the frequency stability tests shall be performed using a new battery without any further requirement to vary supply voltage Test Results Please refer to FCC ID: B4HDST1900 which was granted on 2011-04-08. FCC Part 15D Page 21 of 22

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120106801-00A1 FCC §15.323 (c)(e) & §15.319(f) – SPECIFIC REQUIREMENTS FOR UPCS DEVICE Please refer to FCC ID: B4HDST1900 which was granted on 2011-04-08. ***** END OF REPORT ***** FCC Part 15D Page 22 of 22


Document Created: 2012-02-14 10:47:53
Document Modified: 2012-02-14 10:47:53
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC