Module

FCC ID: AZY-HF-LPT100

Cover Letter(s)

Download: PDF
FCCID_2151856

High-Flying Electronics FCC Modular Approval Request Technology Co., Ltd Number:CF305 Version: V04 Date: 07-08-2012 To the FCC or FCC TCB handling this application Hereby we, Company name (grantee) High-Flying Electronics Technology Co., Ltd Addresss Room 511, #7Building, No.365 Chuanhong Road, Pudong, City / ZIP / State / Country Shanghai, China request modular approval for the certification of our equipment within this application, identified by: FCC ID: AZY-HF-LPT100 The table below contains the justification for modular approval of this equipment: Requirement per 15.212 and KDB 996369 D01 Module Certification Guide v01r03 Explanation from grantee (do not write yes / no, but explain why it complies / how it is achieved) 1. The modular transmitter must have its own RF shielding. No, the modular is only a PCB board. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are The modular has buffered data inputs, it is provided) to ensure that the module will comply with Part 15 requirements under integrated in chip 88WE8782. conditions of excessive data rates or over-modulation. 3. The modular transmitter must have its own power supply regulation. No, DC 5V is fed from the host. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 The module meets the FCC antenna and 15.204(c). The antenna must either be permanently attached or employ a “unique” requirements, It has an unique connector. antenna coupler (at all connections between the module and the antenna, including the cable).. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module The module was tested in a stand-alone must not be inside another device during testing. This is intended to demonstrate that the configuration via a 10M/100M Ethernet network module is capable of complying with Part 15 emission limits regardless of the device into card. which it is eventually installed. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC The label position of FCC ID is clearly indicated. ID is not visible when the module is installed inside another device, then the outside of the Please see the label location. device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating requirements The module is compliant with all applicable FCC applicable to the transmitter and the manufacturer must provide adequate instructions rules. Datail instructions are given in the Users along with the module to explain any such requirements. A copy of these instructions must Manual. be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure requirements. The module complies with the mobile and fixed For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, 20cm separation distance location including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII requirements. and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Attestation (by grantee) City and Country: Date: Name: Function: Signature: (this must be a person) (or official company stamp) Shanghai, China 2013-12-10 Sen Xie General Manager


Document Created: 2013-12-11 11:16:29
Document Modified: 2013-12-11 11:16:29
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC