User Manual

FCC ID: AZPR7003SB-24G

Users Manual

Download: PDF
FCCID_1832917

1M23N17470 R7003SB FASSTest-2.4GHz Bidirectional Communication System S.BUS2 / S.BUS Port and Conventional System Receiver Thank you for purchasing a Futaba R7003SB FASSTest-2.4GHz compatible Applicable systems: Futaba FASSTest-2.4GHz system- receiver. The R7003SB receiver features bi-directional communication with a transmitter FASSTest Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry sensors may be utilized. R7003SB has a If R7003SB does not use S.BUS/S.BUS2 system, it can merit which acquires the information from the model on flight by connecting an perform only operation of 3 channels. However, if S.BUS/ optional telemetry sensors. It also includes both standard PWM output ports and S.BUS2 system is used, use of the maximum channel of S.BUS output ports. 4 ports of R7003SB can choose an output channel from the a transmitter can be performed. You have to use S.BUS/ 11 modes. S.BUS2 servo, in order to use S.BUS/S.BUS2 system. Usage precaution Antenna installation precaution • Analog servos cannot be used with the R7003SB in the FASSTest 12CH mode. Do not cut or bundle the receiver antenna wire. • The R7003SB receiver can only be used with FASSTest capable transmitters. WARNING Do not bend the coaxial cable. It causes damage. Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The antennas must be mounted in such a way to assure they are strain The R7003SB receiver should be protected from vibration by foam rubber, relieved. Velcro or similar mounting methods. Protect from moisture. Keep the antenna as far away from the motor, ESC and other noise sources Keep away from conductive materials to avoid short circuits. as you possibly can. Be sure that the two antennas are placed at 90 degrees to each other. • The R7003SB has two antennas. In order to maximize signal reception and Don't connect the servo or gyro which do not correspond to S.BUS2 port promote safe modeling Futaba has adopted a diversity antenna system. This allows the S.BUS2. receiver to obtain RF signals on both antennas and fly problem-free. • When the servo and gyro which do not correspond to S.BUS2 are connected to S.BUS2 Antenna installation for carbon fuselage port, there is a danger of falling by malfunction. Turn on the power in transmitter → receiver order. In addition, always check WARNING the operation of all the servos before flight. You must leave 30mm at the tip of the antenna fully exposed. The exposed Do not insert or remove the servo connector while the receiver power is antenna should be secured so that it cannot move around or back inside of ON. your aircraft. •Since the S.BUS servo switches the operation mode automatically according to the type of signal (S.BUS signal/PWM signal) from the receiver, if the connector is inserted or removed while the power is ON, an S.BUS connected servo will be erroneously Servo for conventional recognized and may stop. system S.BUS Servo (Antenna installation) 90˚ Please refer the table below for LED status vs receiver's condition. LED Indication Green Red Status HUB Off Solid No signal reception Solid Off Receiving signals S.BUS2 Servo Alternate blink Unrecoverable error (EEPROM, etc.) S.BUS2 Gyro Link/Mode switch LED (It is not used for a link.) R7003SB port 2 HUB S.BUS port 1 S.BUS2 port Antenna HUB Temperature Sensor (Typical installation) Battery Battery to 3/B RPM A battery is connectable Sensor also with which port. HUB Altitude Sensor CH output mode A (Default) SW Example Port Mode Port1 Port2 3/B S.BUS2 A(Default） S.BUS CH2 CH3 S.BUS2 FASSTest FASSTest is a bidirectional communication system between the R7003SB receiver and FASSTest capable transmitters. Multiple optional telemetry sensors may be connected to the S.BUS2 on the receiver and that data is in turn displayed on the transmitter. *Please see your transmitters operation manual to configure transmitter to operate with Compliance Information Statement telemetry sensors. (for U.S.A.) This device, trade name Futaba Corporation of America, model number R7003SB, complies with part15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause R7003SB Specifications undesired operation. FASSTest-2.4GHz system/S.BUS2 and S.BUS port and conventional system receiver (3) This module meets the requirements for a mobile device that may be used at separation distances of more than 20cm from human body. • Dual antenna diversity To meet the RF exposure requirements of the FCC this device shall not be co-located with another • Size: 0.89 x 1.47 x 0.37 in. (22.5 x 37.4 x 9.3 mm) transmitting device. • Weight: 0.25 oz. (7.2g) The responsible party of this device compliance is: • Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V) Futaba Service Center • Battery F/S Voltage: It sets up with a transmitter 3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A. • Extra Voltage port (port2)"EXT-VOL cable and CA-RVIN-700" of an option is used: 0 ～ 70V DC TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support) * Be sure that when using ESCs regulated output the capacity of the ESC must meet your usage condition.

S.BUS2 ＜ How to change R7003SB into "EXT-VOL Mode" ＞ S.BUS2 extends S.BUS and supports bidirectional communication. Sensors are connected 1 Turn on the receiver. LED lights up red. [Transmitter is always OFF] to the S.BUS2 port. 2 Press and hold the Mode/Link button for 5 seconds to 10 seconds. S.BUS Servo S.BUS2 Servo *It becomes the mode which makes a mistake in exceeding 10 seconds. In that case, carry out power Port Telemetry sensor supply OFF and redo. S.BUS Gyro S.BUS2 Gyro S.BUS ○ ○ × 3 The LED should now be early blinking green. Mode/Link button is released. S.BUS2 × （*） ○ ○ 4 Each press of the Mode/Link button advances the receiver to the next mode. 5 When you reach the mode that you wish to operate in, press and hold the Mode/ *Only S.BUS2 capable devices may be connected to the S.BUS2 port. Standard S.BUS Link button for more than 2 seconds. servos and gyros should not be connected to the S.BUS2 port. 6 When LED blinks in green with red, it is the completion of a mode change. Link to the transmitter 7 Please cycle the receiver power off and back on again after changing the EXT- Easy Link ID allows FASSTest receivers to link to compatible transmitter without pressing VOL Mode. the link button on the receiver. Mode External voltage LED blink 1 Bring the transmitter and the receiver close to each other, within 20 inches (half measurement meter). Servo Mode(Default） OFF Green 1 time 2 Turn on the transmitter. Place the transmitter into the receiver linking mode. EXT-VOL Mode ON Green 2 time 3 Turn on the receiver. R7003SB 4 When the LED of the receiver changes from blinking red to solid green, linking *It changes into EXT-VOL Mode is complete. * Refer to the transmitters operation manual for complete details on how to place the transmitter into the linking mode. * If there are many FASSTest systems turned on in close proximity, your receiver might have difficulty establishing a link to your transmitter. This is a rare occurrence. However, should another FASSTest transmitter/receiver be linking at the same time, your receiver could link to the wrong transmitter. This is very dangerous if you do not notice this situation. In order to avoid the problem,we strongly recommend to Port2 you to double check whether your receiver is really under control by your transmitter. * If the System Type of the transmitter is changed, the receiver will need to be re-linked to the transmitter. EXT-VOL CABLE EXT-VOL CABLE * Link is required when a new model is made from a model selection. (It is attached to R7003SB.) (Option) Black line Fuse WARNING EXT-VOL Red line Do not perform the linking procedure while the motor's main wire connected with external power to Motor input must be less than 70V or the engine is operating as it may result in serious injury. Motor Power Battery or Controller When the linking is complete, please cycle the receiver power and ensure another power supply Branch for servos the receiver is properly linked to the transmitter. To Motor Controller or Servo Please power up your system in this order. Transmitter first, followed by the *It connects with reference to the manual of CA-RVIN-700. receiver. WARNING If the R7003SB receiver was previously linked to another transmitter, make sure that transmitter is not operating while linking the receiver to the new Don't touch wiring. transmitter. * There is a danger of receiving an electric shock. Channel Modes Don't connect to Extra Voltage before turning on a receiver. The R7003SB is capable of changing its channel allocations as described in the table When not using EXT-VOL, "EXT-VOL Mode" is turned OFF. below. Please choose the mode which suited the use in the following procedure from the 11 modes. Don't connect EXT-VOL CABLE other than port 2 of R7003SB. 1 Press and hold down the Link/Mode button on the R7003SB receiver. [Transmitter is always OFF] 2 Turn the receiver on while holding down the Link/Mode button. After power up, When using the R7003SB Receiver with the GYA430, the button can be released. GYA431 and CGY750 3 The LED should now be blinking red with green. The following table corresponds to the gyro's functions. A port can be used effectively. 4 Each press of the Mode/Link button advances the receiver to the next mode. The servo which a gyro controls is connected to a gyro. [Refer to CH Mode table shown below.] * Please refer to the description of each gyro manual. 5 When you reach the mode that you wish to operate in, press and hold the Mode/Link button for more than 2 seconds. S.BUS Gyro Goup table 6 When LED blinks in green with red, it is the completion of a mode change. Gyro control CH CH Mode 7 Please cycle the receiver power off and back on again after changing the Rudder D,E Channel Mode. Elevator F *5 seconds after the receiver ON, LED shows CH Mode. Aileron G R7003SB CH Mode table Elevator+Rudder H Port Aileron+Rudder I Mode LED blink Port1 Port2 3/B S.BUS2 Aileron+Elevator J A(Default） S.BUS Red 1 time Aileron+Elevator+Rudder S.BUS2 B S.BUS2 Red 2 time or CGY750 K C S.BUS CH2 Red 3 time D S.BUS Red 4 time [ Example: Connecting GYA431 to R7003SB CH Mode G ] E CH1 Green 1 time （GYA431 is used for the aileron of an airplane） F CH3 Green 2 time CH4 G CH2 Green 3 time H CH1 CH5 S.BUS2 Green 4 time I CH2 CH7 Red and Green 1 time J CH4 CH8 Red and Green 2 time Port 2 CH4 R7003SB K CH11 CH12 Red and Green 3 time Rudder servo Port 1 CH2 Measurement of Extra Voltag Elevator servo R7003SB can display the voltage of a receiver battery on a transmitter. 3/B CH1 Furthermore, the following procedures are required in order to display the voltage of Aileron servo another battery (Drive battery etc.). 1 The optional adapter for CA-RVIN-700 is purchased. S.BUS2 CH6 2nd Aileron servo 2 R7003SB is changed into "EXT-VOL Mode" in the following procedure. HUB Battery GYA431 *If "EXT-VOL Mode" is used, the port 2 cannot be used as the servo CH. CH3 Throttle servo 3 According to the manual of CA-RVIN-700, battery wiring is branched and it connects. 4 One side of EXT-VOL CABLE is connected to the port 2 of R7003SB. FUTABA CORPORATION 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan ©FUTABA CORPORATION 2012, 10 (1) Phone: +81 475 32 6982, Facsimile: +81 475 32 6983


Document Created: 2012-11-02 09:14:27
Document Modified: 2012-11-02 09:14:27
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC