RF Exposure

FCC ID: AZ492FT7116

RF Exposure Info

Download: PDF
FCCID_3984410

FCC ID: AZ492FT7116/ IC: 109U-92FT7116 Report ID: P11691-EME-00001 SAMM No.0826 DECLARATION OF COMPLIANCE: MPE ASSESSMENT Motorola Solutions, Inc. Date of Report: 06/07/2018 EME Test Laboratory Report Revision: B Motorola Solutions Malaysia Sdn Bhd (Innoplex) Plot 2A, Medan Bayan Lepas, Mukim 12 SWD 11900 Bayan Lepas Penang, Malaysia. Responsible Engineer: Tiong Nguk Ing Report Author: Tiong Nguk Ing Assessment Date(s) 3/15/2018 Manufacturer: Motorola Israel DUT Description: MC-EDGE CPU MODULEAPX4000 900 band, LoRA and LTE B4&B13 Test TX mode(s): FM, LoRA and LTE Max. Power output: Baseline: APX4000 900 band Module LoRA: (FCC ID: SQG-1001) Module LTE: (FCC ID: N7NHL7588); For full description of max powers for each transmission mode refer to Table 4. Tx Frequency Bands: Baseline: 896-901 MHz / 935-940 MHz Module LoRA (FCC ID: SQG-1001): 923-927.5 MHz Module LTE (FCC ID: N7NHL7588): LTE B4, LTE B13 For full description of specific transmit frequencies, refer to Table 4. Model(s) Tested: F0016A (VA00714AA, VA00715AA, VA00726AA) Model(s) Certified: F0016A (VA00714AA, VA00715AA, VA00726AA), F0016A (VA00714AA), F0016A (VA00714AA, VA00715AA), F0016A (VA00714AA, VA00726AA) Classification: Occupational / Controlled Environment FCC ID: AZ492FT7116 – Include modules FCC ID: SQG-1001 and N7NHL7588 IC: 109U-92FT7116 – Include modules IC: 2417C-HL7588 and 3147A-1001 Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 4.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc. EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-159 April 2006 The results and statements contained in this report pertain only to the device(s) evaluated herein. Tiong Digitally signed by Tiong Nguk Ing Nguk Date: 2018.06.07 Tiong Nguk Ing Ing 23:30:03 +08'00' Deputy Technical Manager (Approved Signatory) Approval Date: 6/7/2018 Form-MPE Calc. rpt. Rev 3.8 Page 1 of 8

FCC ID: AZ492FT7116/ IC: 109U-92FT7116 Report ID: P11691-EME-00001 Table of Contents 1.0 Introduction ....................................................................................................................................... 3 2.0 Abbreviations / Definitions ............................................................................................................... 3 3.0 Referenced Standards and Guidelines .............................................................................................. 3 4.0 Power Density Limits ....................................................................................................................... 4 5.0 Product and System Description ....................................................................................................... 6 6.0 Assessment Method .......................................................................................................................... 7 7.0 MPE Assessment .............................................................................................................................. 7 8.0 Conclusion ........................................................................................................................................ 8 Report Revision History Date Revision Comments 4/20/2018 A Initial release 6/7/2018 B Update models at cover page. Form-MPE Calc. rpt. Rev 3.8 Page 2 of 8

FCC ID: AZ492FT7116/ IC: 109U-92FT7116 Report ID: P11691-EME-00001 1.0 Introduction This report contains calculated Maximum Permissible Exposure (MPE) results for product model F0016A (VA00714AA, VA00715AA, VA00726AA). This product contains modules FCC ID: N7NHL7588 and SQG-1001. 2.0 Abbreviations / Definitions DUT: Device Under Test EME: Electromagnetic Energy LTE: Long Term Evolution MPE: Maximum Permissible Exposure 3.0 Referenced Standards and Guidelines This product is designed to comply with the following applicable national and international standards and guidelines. • United States Federal Communications Commission, Code of Federal Regulations; Rule Part 47CFR § 1.1310, § 2.1091 (d) and § 2.1093 for RF Exposure, where applicable. • Federal Communications Commission, “Evaluating Compliance with FCC Guidelines for Human Exposure to Radio frequency Electromagnetic Fields”, OET Bulletin 65 (Edition 97- 01), FCC, Washington, D.C.: August 1997. • American National Standards Institute (ANSI) / Institute of Electrical and Electronics Engineers (IEEE) C95. 1-1999 • American National Standards Institute (ANSI) / Institute of Electrical and Electronics Engineers (IEEE) C95. 1-1992. Specific to FCC rules and regulations. • Institute of Electrical and Electronics Engineers (IEEE) C95.3-2002 • Ministry of Health (Canada) Safety Code 6 (2015), Limits of Human Exposure to Radio frequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz • RSS-102 (Issue 5) – Radio Frequency (RF) Exposure Compliance of Radio communication Apparatus (All Frequency Bands) • FCC KDB – 447498 D01 General RF Exposure Guidance v06 • FCC KDB – 865664 D02 RF Exposure Reporting v01r02 Form-MPE Calc. rpt. Rev 3.8 Page 3 of 8

FCC ID: AZ492FT7116/ IC: 109U-92FT7116 Report ID: P11691-EME-00001 4.0 Power Density Limits Table 2 – Occupational / Controlled Exposure Limits IEEE FCC OET IEEE C95.1 C95.1 RSS-102 Frequency Bulletin 65 ICNIRP 1992/1999 2005 Issue 5 2015 Range (MHz) mW/cm^2 W/m^2 mW/cm^2 W/m^2 W/m^2 10 – 20 10.0 20 – 48 44.72 / f 0.5 30 – 300 1.0 48 – 100 6.455 10 – 400 10.0 100 – 300 1.0 10.0 100 – 6,000 0.6455 f 0.5 300 – 1,500 f/300 300 – 3,000 f/300 f/30 400 – 2,000 f/40 1,500 – 15,000 1,500 – 100,000 5.0 2,000 – 300,000 50.0 3,000 – 300,000 10.0 100.0 6,000 – 15,000 50.0 15000 – 150,000 50.0 150000 –300,000 3.33×10-4 f Form-MPE Calc. rpt. Rev 3.8 Page 4 of 8

FCC ID: AZ492FT7116/ IC: 109U-92FT7116 Report ID: P11691-EME-00001 Table 3 – General Population / Uncontrolled Exposure Limits IEEE FCC OET IEEE C95.1 C95.1 RSS-102 Frequency Range Bulletin 65 ICNIRP 1992/1999 2005 Issue 5 2015 (MHz) mW/cm^2 W/m^2 mW/cm^2 W/m^2 W/m^2 10 – 20 2.0 20 – 48 8.944 / f 0.5 30 – 300 0.2 48 – 300 1.291 10 – 400 2.0 100 – 300 0.2 100 – 400 2.0 300 – 1,500 f/1,500 300 – 6000 0.02619 f 0.6834 400 – 2,000 f/200 f/200 300 – 15,000 f/1,500 1,500 – 15,000 1,500 – 100,000 1.0 2,000 – 100,000 10.0 2,000 – 300,000 10.0 6,000 – 15,000 10.0 15,000 – 150,000 10.0 150,000 – 300,000 6.67×10-5 f Form-MPE Calc. rpt. Rev 3.8 Page 5 of 8

FCC ID: AZ492FT7116/ IC: 109U-92FT7116 Report ID: P11691-EME-00001 5.0 Product and System Description Model F0016A (VA00714AA, VA00715AA, VA00726AA) is Remote Terminal Unit (RTU) used in Supervisory Control and Data Acquisition systems to monitoring and controlling/local processing of data in the industries such as water/waste management, oil/gas utilization, electricity and radio communication. The RTU collects data from on-site sensors, adds data from off-site sources, and uses this data aggregate to make decisions regarding how the system’s process is operating. This device consists of 900 band, modules RG191-M2 (FCC ID: SQG-1001) and HL7588 (FCC ID: N7NHL7588) which supports LoRA and LTE. Simultaneous transmission is possible between 900 band, LoRA and LTE (only one LTE band at any given time). Table 4 below summarizes the technologies, bands, maximum duty cycles and maximum output powers. Maximum output powers are defined as upper limit of the production line final test station. Table 4 Technologies Transmit Bands (MHz) Duty Cycle (%) Max Power (W) Baseline: 896-901 100 3.0 FM 935-940 100 3.0 Module RG191-M2 (FCC ID: SQG-1001): LoRA 923.3-927.5 MHz 100 0.589 Module HL7588 (FCC ID: N7NHL7588): LTE B4 1710-1755 100 0.259 LTE B13 777-787 100 0.220 Form-MPE Calc. rpt. Rev 3.8 Page 6 of 8

FCC ID: AZ492FT7116/ IC: 109U-92FT7116 Report ID: P11691-EME-00001 6.0 Assessment Method MPE calculation was used to determine the RF exposure for this device. According to FCC’s OET Bulletin 65 Edition 97-01 Section 2, calculations can be made to predict RF field strength and power density levels around typical RF sources. Equation 1: 𝑃𝑡 𝐺 𝑆= F 4𝜋𝑑 2 Equation (1) accounts for the maximum duty cycle of the signal, and the factor, F, to provide a worst-case prediction of power density per FCC OET Bulletin 65, Edition 97-01 1997. Where: S = power density (mW/cm2) Pt = maximum output power scaled by the maximum duty cycle of the signal (mW) G = Gain of antenna in linear scale d = distance from antenna (cm) F = Enhancement factor for predicting ground-level field strength (2.56) 7.0 MPE Assessment Table 5 summarized the highest MPE calculation for each standalone transmitter bands. Table 5 Max Duty Tx Antenna Max Calc. % To % To Dist., d Enhance FCC Limit ISED limit Antenna # Power Cycle Frequency Gain MPE FCC ISED (cm) Factor, F (mW/cm2) (mW/cm2) (mW) (%) (MHz) (dBi) (mW/cm2) Limit Limit FM (896-901 MHz / 935-940 MHz) 3000 100 896.0 3.00 76 2.56 0.211 0.60 35.3 0.27 77.4 BMLPVMBLTENGP- 3000 100 901.0 3.00 76 2.56 0.211 0.60 35.1 0.27 77.1 VP 3000 100 935.0 3.00 76 2.56 0.211 0.62 33.9 0.28 75.2 3000 100 940.0 3.00 76 2.56 0.211 0.63 33.7 0.28 74.9 LoRA (923.3-927.5 MHz) 589 100 923.3 3.00 76 2.56 0.041 0.62 6.7 0.28 14.9 BMLPVMBLTENGP- 589 100 925.4 3.00 76 2.56 0.041 0.62 6.7 0.28 14.9 VP 589 100 927.5 3.00 76 2.56 0.041 0.62 6.7 0.28 14.8 LTE 4 (1710-1755 MHz) 259 100 1710.0 3.00 76 2.56 0.018 1.00 1.8 0.42 4.3 BMLPVMBLTENGP- 259 100 1732.5 3.00 76 2.56 0.018 1.00 1.8 0.43 4.3 VP 259 100 1755.0 3.00 76 2.56 0.018 1.00 1.8 0.43 4.2 LTE 13 (777-787 MHz) 220 100 777.0 3.00 76 2.56 0.015 0.52 3.0 0.25 6.3 BMLPVMBLTENGP- 220 100 782.0 3.00 76 2.56 0.015 0.52 3.0 0.25 6.2 VP 220 100 787.0 3.00 76 2.56 0.015 0.52 3.0 0.25 6.2 Form-MPE Calc. rpt. Rev 3.8 Page 7 of 8

FCC ID: AZ492FT7116/ IC: 109U-92FT7116 Report ID: P11691-EME-00001 Per KDB 447498 D01, simultaneous transmission MPE test exclusion applies when the sum of MPE ratios for all simultaneous transmitting antennas incorporated in a host device is ≤ 1.0, according to calculated/estimated, numerically modeled, or measured field strengths or power density. The evaluation here considers FM 900 band, LoRA and LTE transmitter are transmitting simultaneously. The sum of MPE percentage to the limit is calculated as follows: Table 6: FCC, US Highest % to FCC limit Sum of MPE Simultaneous Transmission FM LoRA LTE B4 LTE B13 percentage to the FCC Scenario limit 35.3% 6.7% 1.8% 3.0% FM + LoRA + LTE B4 x x x 43.8% FM + LoRA + LTE B13 x x x 45.0% Table 7: ISED, Canada Highest % to ISED limit Sum of MPE Simultaneous Transmission FM LoRA LTE B4 LTE B13 percentage to the ISED Scenario limit 77.4% 14.9% 4.3% 6.3% FM + LoRA + LTE B4 x x x 96.6% FM + LoRA + LTE B13 x x x 98.6% 8.0 Conclusion The MPE assessment presented in this report concludes that model F0014A (VA00710AA, VA00714AA, VA00726AA) when transmitting either in standalone or simultaneously at minimum separation distance 76 cm from antennas, are compliant to the FCC and ISED General Population/Uncontrolled RF exposure limits. Form-MPE Calc. rpt. Rev 3.8 Page 8 of 8


Document Created: 2018-06-07 23:30:03
Document Modified: 2018-06-07 23:30:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC