Test Report LMR

FCC ID: AZ489FT5874

Test Report

Download: PDF
FCCID_4063657

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 SAMM No. 0825 MOTOROLA PENANG ADV. COMM. LABORATORY FCC / IC TEST REPORT Motorola Solutions Malaysia SDN BHD, Report Revision : Rev.A Innoplex, Plot 2A, Medan Bayan Lepas, Mukim 12 S.W.D, 11900 Bayan Lepas, Penang, Malaysia. Date/s Tested : 28-August-2018 - 6-September-2018 Report Issue Date : 18-September-2018 Manufacturer : Motorola Solutions Malaysia SDN BHD Manufacturer Address : Plot 2, Bayan Lepas Technoplex, 11900 Bayan Lepas, Penang, Malaysia Requestor : SUNDRA LINGAM A/L SELVARAJOO Product Type : Portable Model Number : DTS150NBDLAA Frequency Band : 902 - 928 MHz Max RF Output Power : 1 Watt Applicant Name : Motorola Solutions Inc. Firmware Version : D00.00.15 FCC Registrations : 461337 IC Registrations : 109AK The equipment was tested in accordance to the requirement(s) listed below: (900MHz ISM) PASS Part 15C ISED RSS-GEN/247 This report shall not be reproduced without written approval from an officially designated representative of the Motorola Penang Adv. Comm. Laboratory. The results and statements contained in this report pertain only to the device(s) evaluated. Prepared By: Approved By: _________________________ _________________________ Gan Boon Teong Vincent Foong Test Personnel Responsible Engineer 1/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 Table of Contents 1.0. General Information ................................................................................................................................. 3 2.0. Summary of Test Results.......................................................................................................................... 4 3.0. Measurement Uncertainty ......................................................................................................................... 4 4.0. Equipment List ......................................................................................................................................... 5 5.0. Test Mode Applicability and Test Channel Detail ................................................................................... 6 6.0. Transmitter Test Parameters ..................................................................................................................... 7 6.1. Conducted RF Output Power (Peak) and E.I.R.P Measurement ....................................................... 7 6.1.1. Test Setup.................................................................................................................................. 7 6.1.2. Test Limits ................................................................................................................................ 7 6.1.3. Test Data ................................................................................................................................... 7 6.2. 20dB Channel Bandwidth.................................................................................................................. 9 6.2.1. Test Setup.................................................................................................................................. 9 6.2.2. Test Limits ................................................................................................................................ 9 6.2.3. Test Data ................................................................................................................................... 9 6.3. Band-edge Conducted Spurious Emission ...................................................................................... 11 6.3.1. Test Setup................................................................................................................................ 11 6.3.2. Test Limits .............................................................................................................................. 11 6.3.3. Test Result .............................................................................................................................. 11 6.4. Dwell time on each channel............................................................................................................. 13 6.4.1. Test Setup................................................................................................................................ 13 6.4.2. Test Limits .............................................................................................................................. 13 6.4.3. Test Result .............................................................................................................................. 13 6.5. Number of hopping Frequency ........................................................................................................ 15 6.5.1. Test Setup................................................................................................................................ 15 6.5.2. Test Limits .............................................................................................................................. 15 6.5.3. Test Result .............................................................................................................................. 15 Voltage = 3.80V................................................................................................................................. 15 6.6. Channel Separation .......................................................................................................................... 17 6.6.1. Test Setup................................................................................................................................ 17 6.6.2. Test Limits .............................................................................................................................. 17 6.6.3. Test Result .............................................................................................................................. 17 6.7. Conducted Spurious Emission ......................................................................................................... 19 6.7.1. Test Setup................................................................................................................................ 19 6.7.2. Test Limits .............................................................................................................................. 19 6.7.3. Test Data ................................................................................................................................. 19 6.8. Radiated Spurious Emission ............................................................................................................ 21 6.8.1. Test Setup................................................................................................................................ 21 6.8.2. Test Limits .............................................................................................................................. 22 6.8.3. Test Data ................................................................................................................................. 23 6.9. AC Powerline Conducted Emission ................................................................................................ 33 6.9.1. Test Setup................................................................................................................................ 33 6.9.2. Test Limits .............................................................................................................................. 34 6.9.3. Test Result .............................................................................................................................. 34 REVISION HISTORY Revision History Description Date Originator Rev. A Initial Report 18-September-2018 Gan Boon Teong 2/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 1.0. General Information EUT Description: Technologies 900MHz ISM TX Frequency range 902MHz – 928MHz Modulation Type 8FSK No of Hopset 10 No of Channel Per Hopset 50 Input/Output RF port Connector type PROGRAMMING Antenna type Handset Antenna Antenna Gain 2.15 dBi General Description of Applied Standards The EUT is a RF Product. According to the specifications of the manufacturer, the EUT is to comply with the requirements of the following standards: ANSI C63.10-2013 3/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 2.0. Summary of Test Results FCC Clause IC Clause Test Item Result Remark Conducted RF Output Power Highest output power: 15.247 (b)(2) RSS-247 5.4(1) Pass (Peak) & EIRP Measurement 31.4 dBm RSS-247 5.1(3) (1) 20dB Channel Bandwidth Emission designator 15.247 (a)(1) Pass RSS-247 5.1(2) (2) Channel Separation 26K4F1D Number of hopping Frequency 15.247(a)(1)(i) RSS-247 5.1(3) Pass NA used 15.247(a)(1)(i) RSS-247 5.1(3) Dwell time on each channel Pass NA Band Edge Conducted Spurious Worst case emission: 15.247 (d) RSS-247 5.5 Pass Emission -43.5 dBm Worst case emission: 15.247 (d) RSS-247 5.5 Conducted Spurious Emission Pass -31.3 dBm 15.205, 15.209, Radiated Emission within Worst case emission: RSS-247 5.5 Pass 15.247 (d) Restricted Bands 49.7 dBµV/m Testing is not required, AC Powerline Conducted 15.207 RSS-Gen 8.8 NA radio shall turn off during Emission charging mode 3.0. Measurement Uncertainty Measurement Frequency Expended Uncertainty (k=1.96) (±) AC Power Line Conducted Spurious Emission 150KHz ~ 30MHz 3.43 30MHz ~ 200MHz 5.01 Radiated Emissions up to 1 GHz 200MHz ~ 5.01 1000MHz 1GHz ~ 18GHz 5.01 Radiated Emissions above 1 GHz 18GHz ~ 25GHz 5.01 4/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 4.0. Equipment List Bluetooth ATE # 1 (SW Version: Not Applicable) Calibration Calibration Description Model Serial Number Date Due Date POWER SUPPLY 6652A MY40001437 17-Aug-17 17-Aug-19 SPECTRUM ANALYZER FSEK30 838495/014 11-Jul-18 11-Jul-19 SPECTRUM ANALYZER E4445A MY46181597 21-Dec-16 21-Dec-18 10dB ATTENUATOR 33.10.34 NA Not Required Not Required SUCOFLEX RF CABLE MY27726/4 Not Required Not Required 104 Radiated Emission Station (SW Version: EMC FCC RE v1.5.1) Calibration Calibration Description Model Serial Number Date Due Date DRG HORN FREQ. SAS-571 719 18-Jul-17 18-Jul-19 DRG HORN FREQ. SAS-571 720 2-Mar-17 2-Mar-19 POWER SUPPLY 6032A 2615A-01178 13-Jun-18 13-Jun-19 MICROWAVE SIGNAL GENERATOR SMP04 100131 12-Jul-18 11-Jul-19 EMI TEST RECEIVER ESIB40 100307 8-Jul-18 8-Jul-19 EMI TEST RECEIVER ESW44 101750 25-Jun-18 25-Jun-19 5m Semi-anechoic Chamber S800-HX J2308 Not Required Not Required BILOG ANTENNA CBL6112D 30991 23-Apr-18 23-Apr-19 BILOG ANTENNA CBL6112B 2964 16-Feb-18 16-Feb-20 BROAD-BAND HORN ANTENNA BBHA9170 BBHA9170255 7-Nov-17 7-Nov-18 DAT A LOGGER SDL500 A.016776 18-Mar-17 18-Mar-19 LOOP ANTENNA 6502 203479 8-Aug-17 8-Nov-18 AUDIO ANALYZER 8903B 3729A17397 3-Apr-2018 3-Apr-2019 SYSTEM CONTROLLER SC104V 050806-1 Not Required Not Required TURNTABLE FLUSH MOUNT 2M FM2011 NA Not Required Not Required ANTENNA POSITIONING TOWER TLT2 NA Not Required Not Required Miteq Hi Gain 18 - 40GHz PREAMPLIFIER 002 Not Required Not Required Sucoflex PREAMPLIFIER PAM-0118P 361 Not Required Not Required TRILITHIC HIGH PASS FILTER 200551043 Not Required Not Required INC SUCOFLEX RF CABLE #8 500083/6P Not Required Not Required 106P SUCOFLEX RF CABLE #3 500175/6P Not Required Not Required 106P 5/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 5.0. Test Mode Applicability and Test Channel Detail Radiated Emission Test (Above 1GHz) Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Total Channel Tested Channel Modulation Modulation Mode Technology Type Test Mode 1 to 500 Hopset 1: 1, 26 FHSS 8FSK Hopset 10: 50 Radiated Emission Test (Below 1GHz) Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Total Channel Tested Channel Modulation Modulation Mode Technology Type Test Mode 1 to 500 Hopset 1: 1, 26 FHSS 8FSK Hopset 10: 50 Power Line Conducted Emission Test Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Available Tested Modulation Modulation Mode Channel Channel Technology Type Application 1 to 500 AUTO FHSS AUTO Mode Antenna Port Conducted Measurement: This item includes all test value of each mode, but only includes spectrum plot of worst value of each mode. Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Total Channel Tested Channel Modulation Modulation Mode Technology Type Test Mode 1 to 500 Hopset 1: 1, 26 FHSS 8FSK Hopset 10: 50 6/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 6.0. Transmitter Test Parameters 6.1. Conducted RF Output Power (Peak) and E.I.R.P Measurement 6.1.1. Test Setup Spectrum EUT Analyzer a) Check and ensure the spectrum analyzer is well calibrated. b) Turn on the EUT and set EUT to transmit in hopping disable mode. c) Connect EUT’s antenna terminal to spectrum analyzer with a low loss cable. d) Setting of Spectrum analyzer : a. RBW = > 20 dB bandwidth b. VBW = RBW c. Detector mode = Peak d. AMPLITUDE  Scale/Div = 10 dB e. Trace = Max hold f. Sweep = auto e) Measure the captured power within the band and recording the plot. f) Repeat above procedure with different channel frequency of operation. 6.1.2. Test Limits Normal Condition (25 º C) Peak Output Power : < 1W ( or 30dBm); E.I.R.P: < 4W 6.1.3. Test Data Antenna Gain: 2.15dBi Test Conditions Test Peak Output Power E.I.R.P. Frequency Modulation Voltage(V) dBm Watt Status dBm Watt Status (MHz) 902.525 28.979 0.79 Pass 31.129 1.30 Pass 8FSK 3.70 915.025 29.032 0.80 Pass 31.182 1.31 Pass 927.475 29.208 0.83 Pass 31.358 1.37 Pass **Note: EIRP = PT +GT – LC, PT = Transmit Output Power, dBm GT = Antenna Gain, dBi LC = signal attenuation, dB1 7/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 i. The Conducted RF Output Power test with result at low ii. The Conducted RF Output Power test with result at mid frequency, 902.525MHz frequency, 915.025MHz. iii. The Conducted RF Output Power test with result at high frequency, 927.475MHz. 8/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 6.2. 20dB Channel Bandwidth 6.2.1. Test Setup Spectrum EUT Analyzer a) Check and ensure the spectrum analyzer is well calibrated. b) Turn on the EUT and set EUT to transmit in hopping disable mode. c) Connect EUT’s antenna terminal to spectrum analyzer with a low loss cable. d) Setting of Spectrum analyzer : a. RBW = 1 kHz b. VBW = 3 kHz c. SPAN = 130kHz, center on test frequency d. AMPLITUDE  Scale/Div = 10 dB e. Detector mode = Peak f. Trace = Max hold g. Sweep = auto e) Measure 20dB & 99% Bandwidth and record as the emission bandwidth. f) Save the plot result from spectrum analyzer screen. g) Repeat above procedure with different channel frequency of operation. 6.2.2. Test Limits Normal Condition (25 º C) For frequency hopping systems operating in the 902-928 MHz band: if the 20 dB bandwidth of the hopping channel is less than 250 kHz, the system shall use at least 50 hopping frequencies 6.2.3. Test Data Test Conditions Results (MHz) Test Frequency Modulation 20dB Bandwidth 99% Occupied Voltage(V) TX (GHz) Status Type (kHz) Bandwidth (kHz) 902.525 28.544 26.1806 Pass 8FSK 3.70 915.025 29.034 26.3160 Pass 927.475 28.615 26.1976 Pass 9/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 iv. The 20 dB BW & occupied bandwidth test with result at v. The 20 dB BW & occupied bandwidth test with result at low frequency, 902.525MHz. mid frequency, 915.025MHz. vi. The 20 dB BW & occupied bandwidth test with result at high frequency, 927.475MHz. 10/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 6.3. Band-edge Conducted Spurious Emission 6.3.1. Test Setup Spectrum EUT Analyzer a) Check and ensure the spectrum analyzer is well calibrated. b) Turn on the EUT and keep the EUT in hopping mode. c) Connect EUT’s antenna terminal to spectrum analyzer with a low loss cable. d) Setting of Spectrum analyzer : a. RBW = 100 kHz b. VBW = 300 kHz c. SPAN = 4 MHz (Low channel) or 6MHz(High Channel) d. Detector mode = Peak e. Trace = Max hold f. Sweep = auto e) Measure the captured band edge emission result and recording the plot. f) Repeat above on EUT with hopping disable. g) Repeat above procedure with other different test frequency. 6.3.2. Test Limits Normal Condition (25 º C) Shall be at least 20 dB below the peak power. 6.3.3. Test Result Test Conditions Hopping Results Test Frequency(MHz) Modulation Voltage(V) Method dB Status Enabled 902.525 -42.73 Pass 8FSK 3.70 (continuously) 927.475 -43.53 Pass Disabled 902.525 -42.45 Pass (constantly) 927.475 -43.25 Pass 11/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 i. The lowest band edge emission at low carrier frequency ii. The highest band edge emission at high carrier with hopping function enabled, 902.525MHz frequency with hopping function enabled, 927.475MHz iii. The lowest band edge emission at low carrier frequency iv. The highest band edge emission at high carrier with hopping function disabled, 902.525MHz frequency with hopping function disabled, 927.475MHz 12/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 6.4. Dwell time on each channel 6.4.1. Test Setup EUT Spectrum Analyzer a) Check and ensure the spectrum analyzer is well calibrated. b) Turn on the EUT and keep the EUT in hopping mode. c) Connect EUT’s antenna terminal to spectrum analyzer with a low loss cable. d) Setting of Spectrum analyzer : a. RBW = 10 kHz b. VBW = 30 kHz c. SPAN = Zero SPAN, center on hopping frequency d. Detector mode = Peak e. Trace = Max hold f. Sweep time = 10 second g. Sweep = Single e) Measure total numbers of transmissions occur in 10 second and save the plot. f) Change the setting of spectrum analyzer : a. RBW = 10 kHz b. VBW = 30 kHz c. Sweep time = sufficient to capture dwell time for 1 transmission d. Sweep = Single g) Measure dwell time for 1 transmission and save the plot. h) Calculate accumulate dwell time in a given period equal to number of hopping frequencies. i) Repeat above procedure with different channel frequency of operation 6.4.2. Test Limits Normal Condition (25 º C) ≤ 0.4sec 6.4.3. Test Result Test Conditions Results Test No. of Dwell time in Total accumulate Volt Modulation Frequency transmission one transmission dwell time in 20s. Status (V) (MHz) in 10s (a) (msec) (b) (msec) (c) 8FSK 3.70 915.025 1 85.501 171.002 Pass **Note: Total dwell time in 20s, (c) = (a) x (b) x 2 13/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 Dwell Time 14/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 6.5. Number of hopping Frequency 6.5.1. Test Setup Spectrum EUT Analyzer a) Check and ensure the spectrum analyzer is well calibrated. b) Turn on the EUT and keep the EUT in hopping mode. c) Connect EUT’s antenna terminal to spectrum analyzer with a low loss cable. d) Setting of Spectrum analyzer : a. RBW = 10 kHz b. VBW = 10 kHz c. Detector mode = Peak d. Trace = Max hold e) Allow the trace to stabilized & save the plot result from spectrum analyzer screen. f) Count number of channel frequency in the operating. g) Repeat above procedure for other test frequency. 6.5.2. Test Limits Normal Condition (25 º C) ≥ 50 6.5.3. Test Result Voltage = 3.80V Results Sweep Range No. of HOPSET Start Freq Last Freq (MHz) Hopping Status (MHz) (MHz) Frequencies 1 902 - 928 902.525 927.025 50 Pass 15/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 i. Number of Hopping Frequencies per HOPSET 16/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 6.6. Channel Separation 6.6.1. Test Setup EUT Spectrum Analyzer a) Check and ensure the spectrum analyzer is well calibrated. b) Turn on the EUT and keep the EUT in hopping mode. c) Connect EUT’s antenna terminal to spectrum analyzer with a low loss cable. d) Setting of Spectrum analyzer : a. RBW = 10 kHz b. VBW = 30 kHz c. SPAN = 1 MHz, center on test frequency d. Detector mode = Peak e. Trace = Max hold f. Sweep = auto e) Measure the frequency different of these two adjacent channels with marker delta function & record the measurement results. f) Repeat above procedure with different channel frequency of operation 6.6.2. Test Limits Normal Condition (25 º C) At least 25kHz or the 20 dB bandwidth of the hopping channel, whichever is greater. 6.6.3. Test Result Test Test Data Modulation Voltage(V) Frequency Adjacent Channel Status (MHz) Separation (MHz) 902.525 0.510 Pass 8FSK 3.70 915.025 0.503 Pass 927.475 0.507 Pass 17/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 i. The Channel Separation test with result at low ii. The Channel Separation test with result at mid frequency, 902.525MHz. frequency, 915.025MHz. iii. The Channel Separation test with result at high frequency, 927.475MHz. 18/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 6.7. Conducted Spurious Emission 6.7.1. Test Setup Spectrum EUT Analyzer a) Check and ensure the spectrum analyzer is well calibrated. b) Turn on the EUT and set EUT to transmit maximum data rate with hopping disable. c) Connect EUT’s antenna terminal to spectrum analyzer with a low loss cable. d) Setting of Spectrum analyzer : a. RBW = 100 kHz b. VBW = 300 kHz c. SPAN = Cover until 10th harmonic d. Detector mode = Peak e. AMPLITUDE  Scale/Div = 10 dB f. Trace = Max hold g. Sweep = auto e) Measure the captured spurious emission result and recording the plot. f) Repeat above procedure with different channel frequency of operation. 6.7.2. Test Limits Normal Condition (25 º C) Shall be at least 20 dB below for peak power. 6.7.3. Test Data Test Conditions Test Results Frequency Spurious Modulation Voltage(V) Level Status (MHz) 902.525 -30.72 Pass 8FSK 3.70 915.025 -30.17 Pass 927.475 -31.34 Pass 19/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 8FSK Modulation: • The high emission level within the assigned band at low • Spurious emission measurement in 30MHz – 10GHz at low carrier frequency. carrier frequency. • The high emission level within the assigned band at mid • Spurious emission measurement in 30MHz – 10GHz at mid carrier frequency. carrier frequency. • The high emission level within the assigned band at high • Spurious emission measurement in 30MHz – 10GHz at high carrier frequency. carrier frequency. 20/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 6.8. Radiated Spurious Emission 6.8.1. Test Setup a. The EUT is placed on the top of a rotating table 0.8m (<1Ghz) and 1.5m (>1Ghz) above the ground at a 3m semi-anechoic chamber. The table is rotated 360 degrees to determine the position of the highest radiation. b. The EUT is set 3m away from the interference-receiving antenna, which is mounted on the top of a variable-height antenna tower. c. The antenna is Bilog/Horn antenna depend on which frequency range uses, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT is arranged to its worst case and then the antenna is tuned to heights from 1m to 4m and the rotatable table is turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system is set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode is fall within the range of 10dB from the limit specified, the emissions would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. Otherwise, the testing could be stopped and the peak values of the EUT would be reported. NOTE: a. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120 kHz for Quasi-peak detection at frequency below 1GHz. b. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and video bandwidth is 3 MHz for Peak detection at frequency above 1 GHz. c. All modes of operation were investigated and the worst-case emissions are reported. 21/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 6.8.2. Test Limits Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table. Other emissions shall be at least 20dB below the highest level of the desired power. NOTE: a. The lower limit shall apply at the transition frequencies. b. Emission level (dBuV/m) = 20 log Emission level (uV/m). c. For frequencies above 1000 MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. 22/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 6.8.3. Test Data Test: SAC Transmitter Radiated Emission Model#: DTS150NBDLAA S/N: 379TUR0019 EMC SR ID#: 12719-EMC-00005 Battery: PMNN4578A Accessory: NA Test Channel: Low Test Frequency: 902.5250 MHz Test Standard: ANSI C63.10-2013 Worst Case Plane: Z-Plane Radiated Emission (Low Channel) tabular data Vertical Radiated Emission Result Limit Margin Margin Spur level Spur level Spur level Margin Carrier Spur Freq QPK Limit PK Limit A V PK AV QPK PK AV QPK PK Power (MHz) (dBµV/ (dBµV/ m) (dBµV/ m) (dBµV/ (dBµV/ (dBµV/ m) (dBµV/ m) (dBµV/ m) (dBµV/ m) (dBµV/ m) m) m) m) 960.1020 18.8464 - - 54.0000 - - 35.1536 - - - 979.2900 21.7803 - - 54.0000 - - 32.2197 - - - 998.4940 23.5322 - - 54.0000 - - 30.4678 - - - 2707.6800 - 50.1079 35.3938 - 74.0000 54.0000 - 26.0686 20.7826 - Horizontal Radi ated Emission Result 960.1320 34.1486 - - 54.0000 - - 19.8514 - - - 979.2900 25.7260 - - 54.0000 - - 28.2740 - - - 998.5240 31.5832 - - 54.0000 - - 22.4168 - - - 2707.6200 - 50.8345 39.2934 - 74.0000 54.0000 - 25.3412 16.8823 - Remarks: Marginal Result Fail Result Pass Result Temperature (degC): 23.6 Humidity (%): 70.3 Test Performed by: Nazrin & Qawiman Test Date: Tue, Oct 09, 2018 System MU: 5.01dB Remarks: ** Indicates the spurious emission could not be detected due to noise limitations or ambient. *Pursuant to CFR 47 Part 2.1057 ( c ), emissions attenuated more than 20 dB below the permissible limit are not reported. 23/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 VERTICAL, QPK 100 90 80 Spur Level (dBuV/m) 70 60 Spur Level 50 Limit 40 30 20 10 0 960.102 979.29 998.494 Spur Freq (MHz) HORIZONTAL, QPK 100 90 80 Spur Level (dBuV/m) 70 60 50 Spur Level 40 Limit 30 20 10 0 960.132 979.29 998.524 Spur Freq (MHz) VERTICAL, PK 100 90 Spur Level (dBuV/m) 80 70 60 Spur Level 50 Limit 40 30 20 10 0 2707.68 Spur Freq (MHz) 24/34

FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 HORIZONTAL, PK 100 90 80 Spur Level (dBuV/m) 70 60 Spur Level 50 Limit 40 30 20 10 0 2707.62 Spur Freq (MHz) VERTICAL, AV 100 90 80 Spur level (dBuV/m) 70 60 50 Spur Level 40 Limit 30 20 10 0 2707.68 Spur Freq (MHz) HORIZONTAL, AV 100 90 80 Spur level (dBuV/m) 70 60 Spur Level 50 Limit 40 30 20 10 0 2707.62 Spur Freq (MHz) 25/34

Motorola Solutions. FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 Test: SAC Transmitter Radiated Emission Model#: DTS150NBDLAA S/N: 379TUR0019 EMC SR ID#: 12719-EMC-00005 Battery: PMNN4578A Accessory: NA Test Channel: Mid Test Frequency: 915.0250 MHz Test Standard: ANSI C63.10-2013 Worst Case Plane: Z-Plane Radiated Emission (Mid Channel) tabular data Vertical Radiated Emission Result Limit Margin Margin Spur level Spur level Spur level Margin Carrier Spur Freq QPK Limit PK Limit A V PK AV QPK PK AV QPK PK Power (MHz) (dBµV/ (dBµV/ m) (dBµV/ m) (dBµV/ (dBµV/ (dBµV/ m) (dBµV/ m) (dBµV/ m) (dBµV/ m) (dBµV/ m) m) m) m) 2744.9700 - 48.1504 36.3521 - 74.0000 54.0000 - 28.0930 19.8913 - Horizontal Radi ated Emission Result 2745.1500 - 49.6221 40.9428 - 74.0000 54.0000 - 26.6208 15.3001 - Remarks: Marginal Result Fail Result Pass Result Temperature (degC): 23.6 Humidity (%): 70.3 Test Performed by: Nazrin & Qawiman Test Date: Tue, Oct 09, 2018 System MU: 5.01dB Remarks: ** Indicates the spurious emission could not be detected due to noise limitations or ambient. *Pursuant to CFR 47 Part 2.1057 ( c ), emissions attenuated more than 20 dB below the permissible limit are not reported. 26/34

Motorola Solutions. FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 VERTICAL, QPK 100 90 80 Spur Level (dBuV/m) 70 60 Spur Level 50 Limit 40 30 20 10 0 Spur Freq (MHz) HORIZONTAL, QPK 100 90 80 Spur Level (dBuV/m) 70 60 50 Spur Level 40 Limit 30 20 10 0 Spur Freq (MHz) VERTICAL, PK 100 90 Spur Level (dBuV/m) 80 70 60 Spur Level 50 Limit 40 30 20 10 0 2744.97 Spur Freq (MHz) 27/34

Motorola Solutions. FCC ID: AZ489FT5874, IC ID: 109U-89FT5874 HORIZONTAL, PK 100 90 80 Spur Level (dBuV/m) 70 60 Spur Level 50 Limit 40 30 20 10 0 2745.15 Spur Freq (MHz) VERTICAL, AV 100 90 80 Spur level (dBuV/m) 70 60 50 Spur Level 40 Limit 30 20 10 0 2744.97 Spur Freq (MHz) HORIZONTAL, AV 100 90 80 Spur level (dBuV/m) 70 60 Spur Level 50 Limit 40 30 20 10 0 2745.12 Spur Freq (MHz) 28/34

Report Template Document Number : FCD-0109 Report ID: 12719-RF-00013 Report Template Revision Number : Rev. C FCC ID: AZ489FT5874 ISED: 109U-89FT5874 Test: SAC Transmitter Radiated Emission Model#: DTS150NBDLAA S/N: 379TUR0019 EMC SR ID#: 12719-EMC-00005 Battery: PMNN4578A Accessory: NA Test Channel: High Test Frequency: 927.4750 MHz Test Standard: ANSI C63.10-2013 Worst Case Plane: Z-Plane Radiated Emission (High Channel) tabular data Vertical Radiated Emission Result Limit Margin Margin Spur level Spur level Spur level Margin Carrier Spur Freq QPK Limit PK Limit A V PK AV QPK PK AV QPK PK Power (MHz) (dBµV/ (dBµV/ m) (dBµV/ m) (dBµV/ (dBµV/ (dBµV/ m) (dBµV/ m) (dBµV/ m) (dBµV/ m) (dBµV/ m) m) m) m) 964.3560 18.4031 - - 54.0000 - - 35.5969 - - - 2782.3950 - 49.3994 40.0229 - 74.0000 54.0000 - 26.7325 16.1091 - Horizontal Radi ated Emission Result 970.8300 24.1158 - - 54.0000 - - 29.8842 - - - 2782.5450 - 48.8289 41.6009 - 74.0000 54.0000 - 27.3030 14.5311 - Remarks: Marginal Result Fail Result Pass Result Temperature (degC): 23.6 Humidity (%): 70.3 Test Performed by: Nazrin & Qawiman Test Date: Tue, Oct 09, 2018 System MU: 5.01dB Remarks: ** Indicates the spurious emission could not be detected due to noise limitations or ambient. *Pursuant to CFR 47 Part 2.1057 ( c ), emissions attenuated more than 20 dB below the permissible limit are not reported. 29

Report Template Document Number : FCD-0109 Report ID: 12719-RF-00013 Report Template Revision Number : Rev. C FCC ID: AZ489FT5874 ISED: 109U-89FT5874 VERTICAL, QPK 100 90 80 Spur Level (dBuV/m) 70 60 Spur Level 50 Limit 40 30 20 10 0 964.356 Spur Freq (MHz) HORIZONTAL, QPK 100 90 80 Spur Level (dBuV/m) 70 60 50 Spur Level 40 Limit 30 20 10 0 970.83 Spur Freq (MHz) 30

Report Template Document Number : FCD-0109 Report ID: 12719-RF-00013 Report Template Revision Number : Rev. C FCC ID: AZ489FT5874 ISED: 109U-89FT5874 VERTICAL, PK 100 90 Spur Level (dBuV/m) 80 70 60 Spur Level 50 Limit 40 30 20 10 0 2782.395 Spur Freq (MHz) HORIZONTAL, PK 100 90 80 Spur Level (dBuV/m) 70 60 Spur Level 50 Limit 40 30 20 10 0 2782.545 Spur Freq (MHz) 31

Report Template Document Number : FCD-0109 Report ID: 12719-RF-00013 Report Template Revision Number : Rev. C FCC ID: AZ489FT5874 ISED: 109U-89FT5874 VERTICAL, AV 100 90 80 Spur level (dBuV/m) 70 60 50 Spur Level 40 Limit 30 20 10 0 2782.395 Spur Freq (MHz) HORIZONTAL, AV 100 90 80 Spur level (dBuV/m) 70 60 Spur Level 50 Limit 40 30 20 10 0 2782.545 Spur Freq (MHz) 32

Report Template Document Number : FCD-0109 Report ID: 12719-RF-00013 Report Template Revision Number : Rev. C FCC ID: AZ489FT5874 ISED: 109U-89FT5874 6.9. AC Powerline Conducted Emission 6.9.1. Test Setup 1) Tests were conducted for both Receive and Transmit Mode of the EUT. 2) The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/50uH of coupling impedance for the measuring instrument. 3) Both lines of the power mains connected to the EUT were checked for maximum conducted interference. 4) The frequency range from 150 kHz to 30MHz was measured. 33

Report Template Document Number : FCD-0109 Report ID: 12719-RF-00013 Report Template Revision Number : Rev. C FCC ID: AZ489FT5874 ISED: 109U-89FT5874 6.9.2. Test Limits For AC Power Line Conducted Test Limit can be Class A or B depends on product classification. Table 1: Limits for Conducted Disturbance at the Mains Ports of Class A ITE. Table 2: Limits for Conducted Disturbance at the Mains Ports of Class B ITE 6.9.3. Test Result Not Applicable. ~ End of Test Report ~ 34


Document Created: 2018-10-09 16:20:43
Document Modified: 2018-10-09 16:20:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC