Test Report APYHRO00277 DSS

FCC ID: APYHRO00277

Test Report

Download: PDF
FCCID_4473381

FCC RADIO TEST REPORT Report No. : FR990231A FCC RADIO TEST REPORT FCC ID : APYHRO00277 Equipment : Smart phone Brand Name SHARP : Applicant : SHARP CORPORATION 2-13-1, Hachihonmatsu-Iida, Higashi-hiroshima-shi, Hiroshima pref. 739-0192, Japan Manufacturer : SHARP CORPORATION 1 Takumi-Cho, Sakai-Ku, Sakai-Shi, Osaka 590-8522, Japan Standard : FCC Part 15 Subpart C §15.247 The product was received on Sep. 02, 2019 and testing was started from Sep. 20, 2019 and completed on Sep. 26, 2019. We, SPORTON INTERNATIONAL INC., EMC & Wireless Communications Laboratory, would like to declare that the tested sample has been evaluated in accordance with the test procedures and has been in compliance with the applicable technical standards. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any agency of government. The test results in this variant report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory, the test report shall not be reproduced except in full. Reviewed by: Louis Wu SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.) TEL : 886-3-327-3456 Page Number : 1 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A Table of Contents History of this test report ................................................................................................................................. 3 Summary of Test Result................................................................................................................................... 4 1 General Description ................................................................................................................................... 5 1.1 Product Feature of Equipment Under Test ........................................................................................ 5 1.2 Modification of EUT ........................................................................................................................... 5 1.3 Testing Location ................................................................................................................................ 5 1.4 Applicable Standards ......................................................................................................................... 6 2 Test Configuration of Equipment Under Test ......................................................................................... 7 2.1 Carrier Frequency Channel ............................................................................................................... 7 2.2 Test Mode .......................................................................................................................................... 8 2.3 Connection Diagram of Test System ................................................................................................. 9 2.4 Support Unit used in test configuration and system .......................................................................... 9 2.5 EUT Operation Test Setup ................................................................................................................ 9 3 Test Result ................................................................................................................................................ 10 3.1 Output Power Measurement ............................................................................................................ 10 3.2 Radiated Band Edges and Spurious Emission Measurement ........................................................ 11 3.3 Antenna Requirements .................................................................................................................... 15 4 List of Measuring Equipment ................................................................................................................. 16 5 Uncertainty of Evaluation........................................................................................................................ 17 Appendix A. Conducted Test Results Appendix B. Radiated Spurious Emission Appendix C. Radiated Spurious Emission Plots Appendix D. Duty Cycle Plots Appendix E. Setup Photographs TEL : 886-3-327-3456 Page Number : 2 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A History of this test report Report No. Version Description Issued Date FR990231A 01 Initial issue of report Oct. 04, 2019 FR990231A 02 Add the description of Sample difference Oct. 09, 2019 TEL : 886-3-327-3456 Page Number : 3 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A Summary of Test Result Report Ref Std. Result Test Items Remark Clause Clause (PASS/FAIL) - 15.247(a)(1) Number of Channels Not Required - - 15.247(a)(1) Hopping Channel Separation Not Required - - 15.247(a)(1) Dwell Time of Each Channel Not Required - - 15.247(a)(1) 20dB Bandwidth Not Required - - 2.1049 99% Occupied Bandwidth Not Required - 3.1 15.247(b)(1) Peak Output Power Pass - - 15.247(d) Conducted Band Edges Not Required - - 15.247(d) Conducted Spurious Emission Not Required - Under limit Radiated Band Edges and Radiated Spurious 3.2 15.247(d) Pass 7.21 dB at Emission 40.670 MHz - 15.207 AC Conducted Emission Not Required 15.203 & 3.3 Antenna Requirement Pass - 15.247(b) Remark: 1. Not required means after assessing, test items are not necessary to carry out. 2. This is a variant report which can be referred Product Equality Declaration. All the test cases were performed on original report which can be referred to Sporton Report Number FR971613A. Based on the original report, the test cases were verified. Declaration of Conformity: The test results with all measurement uncertainty excluded are presented in accordance with the regulation limits or requirements declared by manufacturers. Comments and Explanations: The declared of product specification for EUT presented in the report are provided by the manufacturer, and the manufacturer takes all the responsibilities for the accuracy of product specification. Reviewed by: Wii Chang Report Producer: Lucy Wu TEL : 886-3-327-3456 Page Number : 4 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A 1 General Description 1.1 Product Feature of Equipment Under Test GSM/WCDMA/LTE, Bluetooth, Wi-Fi 2.4GHz 802.11b/g/n, Wi-Fi 5GHz 802.11a/n/ac, and GNSS. Product Specification subjective to this standard Sample 1 1st vender parts Sample 2 2nd vender parts WWAN: ILA & IFA Antenna WLAN: IFA Antenna Antenna Type Bluetooth: IFA Antenna GPS/Glonass/BDS/Galileo: ILA Antenna Remark: 1. All test items were performed with Sample 1. 2. The difference between Sample 1 & Sample 2 is their suppliers of memory , battery , vibe motor components. 1.2 Modification of EUT No modifications are made to the EUT during all test items. 1.3 Testing Location Test Site SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No.52, Huaya 1st Rd., Guishan Dist., Test Site Taoyuan City, Taiwan (R.O.C.) Location TEL: +886-3-327-3456 FAX: +886-3-328-4978 Sporton Site No. Test Site No. TH05-HY Note: The test site complies with ANSI C63.4 2014 requirement. Test Site SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No.58, Aly. 75, Ln. 564, Wenhua 3rd, Rd., Guishan Dist., Test Site Taoyuan City, Taiwan (R.O.C.) Location TEL: +886-3-327-0868 FAX: +886-3-327-0855 Sporton Site No. Test Site No. 03CH11-HY Note: The test site complies with ANSI C63.4 2014 requirement. FCC designation No.: TW1190 and TW0007 TEL : 886-3-327-3456 Page Number : 5 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A 1.4 Applicable Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards:  FCC Part 15 Subpart C §15.247  FCC KDB Publication No. 558074 D01 DTS Meas. Guidance v05r02  FCC KDB 414788 D01 Radiated Test Site v01r01  ANSI C63.10-2013 Remark: 1. All test items were verified and recorded according to the standards and without any deviation during the test. 2. This EUT has also been tested and complied with the requirements of FCC Part 15, Subpart B, recorded in a separate test report. TEL : 886-3-327-3456 Page Number : 6 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A 2 Test Configuration of Equipment Under Test 2.1 Carrier Frequency Channel Freq. Freq. Freq. Frequency Band Channel Channel Channel (MHz) (MHz) (MHz) 0 2402 27 2429 54 2456 1 2403 28 2430 55 2457 2 2404 29 2431 56 2458 3 2405 30 2432 57 2459 4 2406 31 2433 58 2460 5 2407 32 2434 59 2461 6 2408 33 2435 60 2462 7 2409 34 2436 61 2463 8 2410 35 2437 62 2464 9 2411 36 2438 63 2465 10 2412 37 2439 64 2466 11 2413 38 2440 65 2467 12 2414 39 2441 66 2468 2400-2483.5 MHz 13 2415 40 2442 67 2469 14 2416 41 2443 68 2470 15 2417 42 2444 69 2471 16 2418 43 2445 70 2472 17 2419 44 2446 71 2473 18 2420 45 2447 72 2474 19 2421 46 2448 73 2475 20 2422 47 2449 74 2476 21 2423 48 2450 75 2477 22 2424 49 2451 76 2478 23 2425 50 2452 77 2479 24 2426 51 2453 78 2480 25 2427 52 2454 - - 26 2428 53 2455 - - TEL : 886-3-327-3456 Page Number : 7 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A 2.2 Test Mode The EUT has been associated with peripherals and configuration operated in a manner tended to maximize its emission characteristics in a typical application. Frequency range investigated: radiation emission (9 kHz to the 10th harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower). For radiated measurement, pre-scanned in three orthogonal panels, X, Y, Z. The worst cases (Y plane) were recorded in this report, and the worst mode of radiated spurious emissions is Bluetooth 1Mbps mode, and recorded in this report. The following summary table is showing all test modes to demonstrate in compliance with the standard. Summary table of Test Cases Test Item Data Rate / Modulation Radiated Bluetooth BR 1Mbps GFSK Test Cases Mode 1: CH78_2480 MHz Remark: For radiated test cases, the worst mode data rate 1Mbps was reported only since the highest RF output power in the preliminary tests. The conducted spurious emissions and conducted band edge measurement for other data rates were not worse than 1Mbps, and no other significantly frequencies found in conducted spurious emission. TEL : 886-3-327-3456 Page Number : 8 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A 2.3 Connection Diagram of Test System 2.4 Support Unit used in test configuration and system Item Equipment Trade Name Model Name FCC ID Data Cable Power Cord 1. Bluetooth Base Station R&S CBT32 N/A N/A Unshielded, 1.8 m 2.5 EUT Operation Test Setup The RF test items, utility “QRCT v4.0-00108” was installed in Notebook which was programmed in order to make the EUT get into the engineering modes to contact with base station to provide channel selection, power level, data rate and the application type and for continuous transmitting signals. TEL : 886-3-327-3456 Page Number : 9 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A 3 Test Result 3.1 Output Power Measurement 3.1.1 Limit of Output Power The maximum peak conducted output power of the intentional radiator shall not exceed the following: For frequency hopping systems operating in the 2400-2483.5 MHz band employing at least 75 non-overlapping hopping channels, and all frequency hopping systems in the 5725-5850 MHz band: 1 watt. For all other frequency hopping systems in the 2400-2483.5 MHz band 0.125 watts. The power limit for 1Mbps, 2Mbps, 3Mbps and AFH modes are 0.125 watts. 3.1.2 Measuring Instruments See list of measuring equipment of this test report. 3.1.3 Test Procedures 1. The testing follows ANSI C63.10-2013 clause 7.8.5. 1. The RF output of EUT was connected to the power meter by RF cable and attenuator. The path loss was compensated to the results for each measurement. 2. Set to the maximum power setting and enable the EUT transmit continuously. 3. Measure the conducted output power with cable loss and record the results in the test report. 4. Measure and record the results in the test report. 3.1.4 Test Setup 3.1.5 Test Result of Peak Output Power Please refer to Appendix A. 3.1.6 Test Result of Average Output Power (Reporting Only) Please refer to Appendix A. TEL : 886-3-327-3456 Page Number : 10 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A 3.2 Radiated Band Edges and Spurious Emission Measurement 3.2.1 Limit of Radiated Band Edges and Spurious Emission In any 100 kHz bandwidth outside the intentional radiator frequency band, all harmonics/spurious must be at least 20 dB below the highest emission level within the authorized band. In addition, radiated emissions which fall in the restricted bands must also comply with the limits as below. Frequency Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009 – 0.490 2400/F(kHz) 300 0.490 – 1.705 24000/F(kHz) 30 1.705 – 30.0 30 30 30 – 88 100 3 88 – 216 150 3 216 - 960 200 3 Above 960 500 3 3.2.2 Measuring Instruments See list of measuring equipment of this test report. TEL : 886-3-327-3456 Page Number : 11 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A 3.2.3 Test Procedures 1. The EUT was placed on a turntable with 0.8 meter for frequency below 1GHz and 1.5 meter for frequency above 1GHz respectively above ground. 2. The EUT was set 3 meters from the interference receiving antenna, which was mounted on the top of a variable height antenna tower. 3. For each suspected emission, the EUT was arranged to its worst case and then tune the Antenna tower (from 1 m to 4 m) and turntable (from 0 degree to 360 degrees) to find the maximum reading. A pre-amp and a high pass filter are used for the test in order to get better signal level to comply with the guidelines. 4. Set to the maximum power setting and enable the EUT transmit continuously. 5. Use the following spectrum analyzer settings: (1) Span shall wide enough to fully capture the emission being measured; (2) Set RBW=100 kHz for f < 1 GHz, RBW=1MHz for f>1GHz ; VBW  RBW; Sweep = auto; Detector function = peak; Trace = max hold for peak (3) For average measurement: use duty cycle correction factor method per 15.35(c). Duty cycle = On time/100 milliseconds On time = N1*L1+N2*L2+...+Nn-1*LNn-1+Nn*Ln Where N1 is number of type 1 pulses, L1 is length of type 1 pulses, etc. Average Emission Level = Peak Emission Level + 20*log(Duty cycle) 6. Corrected Reading: Antenna Factor + Cable Loss + Read Level - Preamp Factor = Level 7. For testing below 1GHz, if the emission level of the EUT in peak mode was 3 dB lower than the limit specified, then peak values of EUT will be reported, otherwise, the emissions will be repeated one by one using the CISPR quasi-peak method and reported. 8. For testing above 1GHz, the emission level of the EUT in peak mode was 20dB lower than average limit (that means the emission level in average mode also complies with the limit in average mode), then peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. Note: The average levels were calculated from the peak level corrected with duty cycle correction factor (-24.76dB) derived from 20log (dwell time/100ms). This correction is only for signals that hop with the fundamental signal, such as band-edge and harmonic. Other spurious signals that are independent of the hopping signal would not use this correction. TEL : 886-3-327-3456 Page Number : 12 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A 3.2.4 Test Setup For radiated emissions below 30MHz For radiated emissions from 30MHz to 1GHz TEL : 886-3-327-3456 Page Number : 13 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A For radiated emissions above 1GHz 3.2.5 Test Results of Radiated Spurious Emissions (9 kHz ~ 30 MHz) The low frequency, which started from 9 kHz to 30MHz, was pre-scanned and the result which was 20dB lower than the limit line was not reported. There is a comparison data of both open-field test site and alternative test site - semi-Anechoic chamber according to 414788 D01 Radiated Test Site v01r01, and the result came out very similar. 3.2.6 Test Result of Radiated Spurious at Band Edges Please refer to Appendix B and C. 3.2.7 Duty Cycle Please refer to Appendix D. 3.2.8 Test Result of Radiated Spurious Emission (30MHz ~ 10th Harmonic) Please refer to Appendix B and C. TEL : 886-3-327-3456 Page Number : 14 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A 3.3 Antenna Requirements 3.3.1 Standard Applicable If directional gain of transmitting antennas is greater than 6dBi, the power shall be reduced by the same level in dB comparing to gain minus 6dBi. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the rule. 3.3.2 Antenna Anti-Replacement Construction An embedded-in antenna design is used. 3.3.3 Antenna Gain The antenna peak gain of EUT is less than 6 dBi. Therefore, it is not necessary to reduce maximum peak output power limit. TEL : 886-3-327-3456 Page Number : 15 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A 4 List of Measuring Equipment Calibration Instrument Manufacturer Model No. Serial No. Characteristics Test Date Due Date Remark Date Sep. 20, 2019~ Conducted Power Meter Agilent E4416A GB41292344 N/A Dec. 27, 2018 Dec. 26, 2019 Sep. 26, 2019 (TH05-HY) Power Sep. 20, 2019~ Conducted Agilent E9327A US40441548 50MHz~18GHz Dec. 27, 2018 Dec. 26, 2019 Sensor Sep. 26, 2019 (TH05-HY) Spectrum Rohde & Sep. 20, 2019~ Conducted FSV40 101397 10Hz~40GHz Nov. 13, 2018 Nov. 12, 2019 Analyzer Schwarz Sep. 26, 2019 (TH05-HY) Switch Box & Sep. 20, 2019~ Conducted Burgeon ETF-058 EC1208382 N/A Mar. 27, 2019 Mar. 26, 2020 RF Cable Sep. 26, 2019 (TH05-HY) Sep. 22, 2019~ Radiation Preamplifier EMEC EM18G40G 060715 18GHz ~ 40GHz Dec. 06, 2018 Dec. 05, 2019 Sep. 26, 2019 (03CH11-HY) Sep. 22, 2019~ Radiation Amplifier SONOMA 310N 187312 9kHz~1GHz Dec. 04, 2018 Dec. 03, 2019 Sep. 26, 2019 (03CH11-HY) Bilog CBL 6111D&N 35414&AT-N06 Sep. 22, 2019~ Radiation TESEQ 30MHz~1GHz Oct. 13, 2018 Oct. 12, 2019 Antenna -6-06 02 Sep. 26, 2019 (03CH11-HY) Horn SCHWARZBEC Sep. 22, 2019~ Radiation BBHA 9120 D 9120D-1326 1GHz ~ 18GHz Oct. 30, 2018 Oct. 29, 2019 Antenna K Sep. 26, 2019 (03CH11-HY) Loop Rohde & Sep. 22, 2019~ Radiation HFH2-Z2 100488 9 kHz~30 MHz Nov. 22, 2018 Nov. 21, 2019 Antenna Schwarz Sep. 26, 2019 (03CH11-HY) Sep. 22, 2019~ Radiation Preamplifier Keysight 83017A MY53270080 1GHz~26.5GHz Nov. 14, 2018 Nov. 13, 2020 Sep. 26, 2019 (03CH11-HY) Spectrum Sep. 22, 2019~ Radiation Keysight N9010A MY54200486 10Hz ~ 44GHz Oct. 19, 2018 Oct. 18, 2019 Analyzer Sep. 26, 2019 (03CH11-HY) Antenna Sep. 22, 2019~ Radiation EMEC AM-BS-4500-B N/A 1~4m N/A N/A Mast Sep. 26, 2019 (03CH11-HY) Sep. 22, 2019~ Radiation Turn Table EMEC TT 2000 N/A 0~360 Degree N/A N/A Sep. 26, 2019 (03CH11-HY) AMF-7D-00101 Sep. 22, 2019~ Radiation Preamplifier MITEQ 1590074 1GHz~18GHz May 20, 2019 May 19, 2020 800-30-10P Sep. 26, 2019 (03CH11-HY) SHF-EHF SCHWARZBEC Sep. 22, 2019~ Radiation Horn BBHA 9170 BBHA9170584 18GHz- 40GHz Dec. 05, 2018 Dec. 04, 2019 K Sep. 26, 2019 (03CH11-HY) Antenna EMI Test Sep. 22, 2019~ Radiation Keysight N9038A(MXE) MY55420170 20MHz~8.4GHz Mar. 08, 2019 Mar. 07, 2020 Receiver Sep. 26, 2019 (03CH11-HY) Sep. 22, 2019~ Radiation Software Audix E3 6.2009-8-24 RK-001042 N/A N/A N/A Sep. 26, 2019 (03CH11-HY) HUBER + SUCOFLEX Sep. 22, 2019~ Radiation RF Cable MY9837/4PE 9kHz-30MHz Mar. 13, 2019 Mar. 12, 2020 SUHNER 104 Sep. 26, 2019 (03CH11-HY) HUBER + SUCOFLEX Sep. 22, 2019~ Radiation RF Cable MY2859/2 30MHz-40GHz Mar. 13, 2019 Mar. 12, 2020 SUHNER 102 Sep. 26, 2019 (03CH11-HY) HUBER + SUCOFLEX Sep. 22, 2019~ Radiation RF Cable MY9837/4PE 30M-18G Mar. 13, 2019 Mar. 12, 2020 SUHNER 104 Sep. 26, 2019 (03CH11-HY) HUBER + SUCOFLEX Sep. 22, 2019~ Radiation RF Cable MY4274/2 30MHz-40GHz Mar. 13, 2019 Mar. 12, 2020 SUHNER 102 Sep. 26, 2019 (03CH11-HY) WLJ4-1000-15 1.53GHz Low Sep. 22, 2019~ Radiation Filter Wainwright SN4 Jul. 04, 2019 Jul. 03, 2020 30-6000-40ST Pass Filter Sep. 26, 2019 (03CH11-HY) WHKX12-2700 3GHz High Pass Sep. 22, 2019~ Radiation Filter Wainwright -3000-18000-6 SN2 Jul. 15, 2019 Jul. 14, 2020 Filter Sep. 26, 2019 (03CH11-HY) 0ST TEL : 886-3-327-3456 Page Number : 16 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

FCC RADIO TEST REPORT Report No. : FR990231A 5 Uncertainty of Evaluation Uncertainty of Radiated Emission Measurement (30 MHz ~ 1000 MHz) Measuring Uncertainty for a Level of Confidence 5.2 of 95% (U = 2Uc(y)) Uncertainty of Radiated Emission Measurement (1000 MHz ~ 18000 MHz) Measuring Uncertainty for a Level of Confidence 5.5 of 95% (U = 2Uc(y)) Uncertainty of Radiated Emission Measurement (18000 MHz ~ 40000 MHz) Measuring Uncertainty for a Level of Confidence 5.2 of 95% (U = 2Uc(y)) TEL : 886-3-327-3456 Page Number : 17 of 17 FAX : 886-3-328-4978 Issued Date : Oct. 09, 2019 Report Template No.: BU5-FR15CBT Version 2.4 Report Version : 02

Report Number : FR990231A Appendix A. Test Result of Conducted Test Items Test Engineer: Richard Qiu Temperature: 21~25 °C Test Date: 2019/09/20~2019/09/26 Relative Humidity: 51~54 % TEST RESULTS DATA Peak Power Table Peak Power Power Limit Test DH CH. NTX (dBm) (dBm) Result 0 1 10.02 20.97 Pass DH1 39 1 10.81 20.97 Pass 78 1 10.02 20.97 Pass 0 1 9.42 20.97 Pass 2DH1 39 1 10.06 20.97 Pass 78 1 9.39 20.97 Pass 0 1 9.77 20.97 Pass 3DH1 39 1 10.32 20.97 Pass 78 1 9.69 20.97 Pass TEST RESULTS DATA Average Power Table (Reporting Only) Average Power Duty Factor DH CH. NTX (dBm) (dB) 0 1 9.78 5.18 DH1 39 1 10.50 5.18 78 1 9.78 5.18 0 1 7.26 5.12 2DH1 39 1 7.70 5.12 78 1 7.37 5.12 0 1 7.29 5.12 3DH1 39 1 7.68 5.12 78 1 7.40 5.12 A1 of A1

serovc«s. FCC RADIO TEST REPORT Report No. : FR990231A Appendix B. Radiated Spurious Emission . . Temperature : 21.5~26.8°C Test Engineer : Wait Tseng, Fu Chen, and Troye Hsigh — — Relative Humidity : (48.5~69.3% 2.A4GHz 2400~2483.5MHz BT (Band Edge @ 3m) BT ‘Note Frequency Level Over‘ Limit Read ‘Antenna Path Preamp‘ Ant Table ‘Peak Pol. | Limit | Line Level | Factor Loss Factor | Pos Pos |Avg. (MHz ) _|(dBpuV/im)| (dB ) |(dBpuV/m)|(dBuV)| (dB/m)| (dB) (dB ) |(cm)|(deg )|(P/A)|(H/V) * 2480 98.09 — — 97.59 27.3 6.8 33.6 116 206 P H 2480 73.33 — — — — — — — — A H 2483.68 47.32 —26.68 74 46.81 27.3 6.81 33.6 16 206 P H 2483.68 22.56 —31.44 54 — — — — — — A H H BT H CH 78 * 2480 99.87 — — 99.37 27.3 6.8 33.6 304 282 P V 2480MHz 2480 75.11 — — — — — — — — A V 2483.72 48.75 <25.25 74 48.24 27.3 6.81 33.6 304 282 P V 2483.72 23.99 30.01 54 — — — — — — A V V V 1. No other spurious found. Remark 2. All results are PASS against Peak and Average limit line. TEL : 886—3—327—3456 Page Number : B1 of B5 FAX : 886—3—328—4978

FCC RADIO TEST REPORT Report No. : FR990231A 2.4GHz 2400~2483.5MHz BT (Harmonic @ 3m) BT Note Frequency Level Over Limit Read Antenna Path Preamp Ant Table Peak Pol. Limit Line Level Factor Loss Factor Pos Pos Avg. ( MHz ) ( dBμV/m ) ( dB ) ( dBμV/m ) ( dBμV ) ( dB/m ) ( dB ) ( dB ) ( cm ) ( deg ) (P/A) (H/V) 4960 41.89 -32.11 74 56.65 31.32 11.19 57.27 100 0 P H 7440 42.32 -31.68 74 49.67 36.48 13.61 57.44 100 0 P H H BT H CH 78 4960 41.09 -32.91 74 55.85 31.32 11.19 57.27 100 0 P V 2480MHz 7440 42.45 -31.55 74 49.8 36.48 13.61 57.44 100 0 P V V V 1. No other spurious found. Remark 2. All results are PASS against Peak and Average limit line. TEL : 886-3-327-3456 Page Number : B2 of B5 FAX : 886-3-328-4978

FCC RADIO TEST REPORT Report No. : FR990231A Emission below 1GHz 2.4GHz BT (LF) BT Note Frequency Level Over Limit Read Antenna Path Preamp Ant Table Peak Pol. Limit Line Level Factor Loss Factor Pos Pos Avg. ( MHz ) ( dBμV/m ) ( dB ) ( dBμV/m ) (dBμV) ( dB/m ) ( dB ) ( dB ) ( cm ) ( deg ) (P/A) (H/V) 30 23.91 -16.09 40 31.51 24.01 0.77 32.38 - - P H 40.67 22.64 -17.36 40 35.45 18.7 0.86 32.37 - - P H 54.25 21.12 -18.88 40 40.18 12.31 1 32.37 - - P H 942.77 32.73 -13.27 46 29.24 30.12 4.33 30.96 - - P H 949.56 33.42 -12.58 46 29.42 30.55 4.34 30.89 - - P H 955.38 34.67 -11.33 46 30.35 30.81 4.35 30.84 100 0 P H H H H H H 2.4GHz H BT 40.67 32.79 -7.21 40 45.6 18.7 0.86 32.37 100 0 P V LF 54.25 29.18 -10.82 40 48.24 12.31 1 32.37 - - P V 73.65 27.81 -12.19 40 46.57 12.4 1.19 32.35 - - P V 931.13 33.1 -12.9 46 30.35 29.52 4.29 31.06 - - P V 944.71 33.63 -12.37 46 29.99 30.25 4.33 30.94 - - P V 951.5 34.13 -11.87 46 30.03 30.64 4.34 30.88 - - P V V V V V V V 1. No other spurious found. Remark 2. All results are PASS against limit line. TEL : 886-3-327-3456 Page Number : B3 of B5 FAX : 886-3-328-4978

FCC RADIO TEST REPORT Report No. : FR990231A Note symbol Fundamental Frequency which can be ignored. However, the level of any unwanted emissions * shall not exceed the level of the fundamental frequency. ! Test result is over limit line. P/A Peak or Average H/V Horizontal or Vertical TEL : 886-3-327-3456 Page Number : B4 of B5 FAX : 886-3-328-4978

FCC RADIO TEST REPORT Report No. : FR990231A A calculation example for radiated spurious emission is shown as below: BT Note Frequency Level Over Limit Read Antenna Path Preamp Ant Table Peak Pol. Limit Line Level Factor Loss Factor Pos Pos Avg. ( MHz ) ( dBμV/m ) ( dB ) ( dBμV/m ) ( dBμV ) ( dB/m ) ( dB ) ( dB ) ( cm ) ( deg ) (P/A) (H/V) BT 2390 55.45 -18.55 74 54.51 32.22 4.58 35.86 103 308 P H CH 00 2402MHz 2390 43.54 -10.46 54 42.6 32.22 4.58 35.86 103 308 A H 1. Path Loss(dB) = Cable loss(dB) + Filter loss(dB) + Attenuator loss(dB) 2. Level(dBμV/m) = Antenna Factor(dB/m) + Path Loss(dB) + Read Level(dBμV) - Preamp Factor(dB) 3. Over Limit(dB) = Level(dBμV/m) – Limit Line(dBμV/m) For Peak Limit @ 2390MHz: 1. Level(dBμV/m) = Antenna Factor(dB/m) + Path Loss(dB) + Read Level(dBμV) - Preamp Factor(dB) = 32.22(dB/m) + 4.58(dB) + 54.51(dBμV) – 35.86 (dB) = 55.45 (dBμV/m) 2. Over Limit(dB) = Level(dBμV/m) – Limit Line(dBμV/m) = 55.45(dBμV/m) – 74(dBμV/m) = -18.55(dB) For Average Limit @ 2390MHz: 1. Level(dBμV/m) = Antenna Factor(dB/m) + Path Loss(dB) + Read Level(dBμV) - Preamp Factor(dB) = 32.22(dB/m) + 4.58(dB) + 42.6(dBμV) – 35.86 (dB) = 43.54 (dBμV/m) 2. Over Limit(dB) = Level(dBμV/m) – Limit Line(dBμV/m) = 43.54(dBμV/m) – 54(dBμV/m) = -10.46(dB) Both peak and average measured complies with the limit line, so test result is “PASS”. TEL : 886-3-327-3456 Page Number : B5 of B5 FAX : 886-3-328-4978

FCC RADIO TEST REPORT Report No. : FR990231A Appendix C. Radiated Spurious Emission Plots Temperature : 21.5~26.8°C Test Engineer : Watt Tseng, Fu Chen, and Troye Hsieh Relative Humidity : 48.5~69.3% 2.4GHz 2400~2483.5MHz BT (Band Edge @ 3m) BT 2.4GHz 2400~2483.5MHz Band Edge @ 3m BT CH78 2480MHz Horizontal Fundamental Peak TEL : 886-3-327-3456 Page Number : C1 of C4 FAX : 886-3-328-4978

FCC RADIO TEST REPORT Report No. : FR990231A BT 2.4GHz 2400~2483.5MHz Band Edge @ 3m BT CH78 2480MHz Vertical Fundamental Peak TEL : 886-3-327-3456 Page Number : C2 of C4 FAX : 886-3-328-4978

FCC RADIO TEST REPORT Report No. : FR990231A 2.4GHz 2400~2483.5MHz BT (Harmonic @ 3m) BT 2.4GHz 2400~2483.5MHz Harmonic @ 3m BT CH78 2480MHz Horizontal Vertical Peak Avg. TEL : 886-3-327-3456 Page Number : C3 of C4 FAX : 886-3-328-4978

FCC RADIO TEST REPORT Report No. : FR990231A Emission below 1GHz 2.4GHz BT (LF) BT 2.4GHz 2400~2483.5MHz BT LF Horizontal Vertical QP / Peak TEL : 886-3-327-3456 Page Number : C4 of C4 FAX : 886-3-328-4978

FCC RADIO TEST REPORT Report No. : FR990231A Appendix D. Duty Cycle Plots DH5 on time (One Pulse) Plot on Channel 39 on time (Count Pulses) Plot on Channel 39 Note: 1. Worst case Duty cycle = on time/100 milliseconds = 2 * 2.89 / 100 = 5.78 % 2. Worst case Duty cycle correction factor = 20*log(Duty cycle) = -24.76 dB 3. DH5 has the highest duty cycle worst case and is reported. TEL : 886-3-327-3456 Page Number : D1 of D2 FAX : 886-3-328-4978

FCC RADIO TEST REPORT Report No. : FR990231A Duty Cycle Correction Factor Consideration for AFH mode: Bluetooth normal hopping rate is 1600Hz and reduced to 800Hz in AFH mode; due to the reduced number of hopping frequencies, with the same packet configuration the dwell time in each channel frequency within 100msec period is longer in AFH mode than normal mode. In AFH mode, the minimum hopping frequencies are 20, to get the longest dwell time DH5 packet is observed; the period to have DH5 packet completing one hopping sequence is 2.89 ms x 20 channels = 57.8 ms There cannot be 2 complete hopping sequences within 100ms period, considering the random hopping behavior, maximum 2 hops can be possibly observed within the period. [100ms / 57.8ms ] = 2 hops Thus, the maximum possible ON time: 2.89 ms x 2 = 5.78 ms Worst case Duty Cycle Correction factor, which is derived from the maximum possible ON time, 20 x log(5.78 ms/100ms) = -24.76 dB TEL : 886-3-327-3456 Page Number : D2 of D2 FAX : 886-3-328-4978


Document Created: 2019-10-12 03:06:34
Document Modified: 2019-10-12 03:06:34
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC