SAR Plots 5of5

FCC ID: ALH431000

RF Exposure Info

Download: PDF
FCCID_1455450

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #76 (A76) Date Tested: 01/31/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 470.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 2 (Earpiece); Type: Clip Mic w/ Earphone (P/N: KHS-26) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.1°C; Fluid Temp: 23.2°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 470 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used: f = 470 MHz; ı = 0.95 mho/m; İr = 58.6; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 11.1 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 113.0 V/m; Power Drift = -0.338 dB Peak SAR (extrapolated) = 16.8 W/kg SAR(1 g) = 11.5 mW/g; SAR(10 g) = 8.28 mW/g Maximum value of SAR (measured) = 12.0 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 214 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #77 (A77) Date Tested: 01/28/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 484.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 2 (Earpiece); Type: Clip Mic w/ Earphone (P/N: KHS-26) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.0°C; Fluid Temp: 23.1°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 484 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 484 MHz; ı = 0.954 mho/m; İr = 58.5; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 13.7 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 122.9 V/m; Power Drift = -0.470 dB Peak SAR (extrapolated) = 19.3 W/kg SAR(1 g) = 13.2 mW/g; SAR(10 g) = 9.44 mW/g Maximum value of SAR (measured) = 13.9 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 215 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #78 (A78) Date Tested: 04/06/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 484.0 MHz DUT: Kenwood NX-320-K; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 0320K124 Audio Accessory Category 2 (Earpiece); Type: Clip Mic w/ Earphone (P/N: KHS-26) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 21.0°C; Fluid Temp: 20.3°C; Barometric Pressure: 101.1 kPa; Humidity: 32% Communication System: CW Frequency: 484 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 484 MHz; ı = 0.942 mho/m; İr = 58.1; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglas Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.1 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 116.6 V/m; Power Drift = -0.569 dB Peak SAR (extrapolated) = 18.1 W/kg SAR(1 g) = 12.4 mW/g; SAR(10 g) = 8.87 mW/g Maximum value of SAR (measured) = 13.1 mW/g Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 216 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #79 (A79) Date Tested: 04/05/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 484.0 MHz DUT: Kenwood NX-320-K2; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 0320K218 Audio Accessory Category 2 (Earpiece); Type: Clip Mic w/ Earphone (P/N: KHS-26) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 22.0°C; Fluid Temp: 20.5°C; Barometric Pressure: 101.1 kPa; Humidity: 28% Communication System: CW Frequency: 484 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 484 MHz; ı = 0.938 mho/m; İr = 58.1; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglas Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.2 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 117.3 V/m; Power Drift = -0.461 dB Peak SAR (extrapolated) = 18.0 W/kg SAR(1 g) = 12.3 mW/g; SAR(10 g) = 8.82 mW/g Maximum value of SAR (measured) = 12.9 mW/g Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 217 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #80 (A80) Date Tested: 01/31/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 498.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 2 (Earpiece); Type: Clip Mic w/ Earphone (P/N: KHS-26) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.1°C; Fluid Temp: 23.2°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 498 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 498 MHz; ı = 0.978 mho/m; İr = 59.5; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.9 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 120.0 V/m; Power Drift = -0.363 dB Peak SAR (extrapolated) = 19.2 W/kg SAR(1 g) = 13.2 mW/g; SAR(10 g) = 9.46 mW/g Maximum value of SAR (measured) = 13.8 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 218 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #81 (A81) Date Tested: 01/31/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 512.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 2 (Earpiece); Type: Clip Mic w/ Earphone (P/N: KHS-26) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.1°C; Fluid Temp: 23.2°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 512 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 512 MHz; ı = 0.98 mho/m; İr = 58.2; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.4 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 110.3 V/m; Power Drift = -0.196 dB Peak SAR (extrapolated) = 17.4 W/kg SAR(1 g) = 12 mW/g; SAR(10 g) = 8.52 mW/g Maximum value of SAR (measured) = 12.6 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 219 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #82 (A82) Date Tested: 01/28/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 470.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 3 (Palm-Mic Kit); Type: 2-Wire Palm Mic w/ Earphone (P/N: KHS-8BL) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.0°C; Fluid Temp: 23.1°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 470 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used: f = 470 MHz; ı = 0.93 mho/m; İr = 58.8; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 11.4 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 106.0 V/m; Power Drift = 0.098 dB Peak SAR (extrapolated) = 15.6 W/kg SAR(1 g) = 10.7 mW/g; SAR(10 g) = 7.7 mW/g Maximum value of SAR (measured) = 11.2 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 220 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #83 (A83) Date Tested: 01/28/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 484.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 3 (Palm-Mic Kit); Type: 2-Wire Palm Mic w/ Earphone (P/N: KHS-8BL) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.0°C; Fluid Temp: 23.1°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 484 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 484 MHz; ı = 0.954 mho/m; İr = 58.5; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 14.1 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 123.3 V/m; Power Drift = -0.485 dB Peak SAR (extrapolated) = 19.7 W/kg SAR(1 g) = 13.5 mW/g; SAR(10 g) = 9.68 mW/g Maximum value of SAR (measured) = 14.2 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 221 of 361

4 : Een 4 450 MHz Body SAR(x.y.z,f0) 14 SAR; Z Scan:Value Along Z, X=0, Y=0 12 IR \\ 10 C \ s L a | E L ; e \ ° Y al _/ 2—— \\\\ 07\\\\\\\\\\.\\#*\“‘%4\\\\\\\\ 0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 m KENWOOD

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #84 (A84) Date Tested: 04/06/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 484.0 MHz DUT: Kenwood NX-320-K; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 0320K124 Audio Accessory Category 3 (Palm-Mic Kit); Type: 2-Wire Palm Mic w/ Earphone (P/N: KHS-8BL) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 21.0°C; Fluid Temp: 20.3°C; Barometric Pressure: 101.1 kPa; Humidity: 32% Communication System: CW Frequency: 484 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 484 MHz; ı = 0.942 mho/m; İr = 58.1; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglas Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.3 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 118.0 V/m; Power Drift = -0.538 dB Peak SAR (extrapolated) = 18.1 W/kg SAR(1 g) = 12.5 mW/g; SAR(10 g) = 8.92 mW/g Maximum value of SAR (measured) = 13.1 mW/g Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 223 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #85 (A85) Date Tested: 04/06/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 484.0 MHz DUT: Kenwood NX-320-K2; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 0320K1218 Audio Accessory Category 3 (Palm-Mic Kit); Type: 2-Wire Palm Mic w/ Earphone (P/N: KHS-8BL) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 21.0°C; Fluid Temp: 20.3°C; Barometric Pressure: 101.1 kPa; Humidity: 32% Communication System: CW Frequency: 484 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 484 MHz; ı = 0.942 mho/m; İr = 58.1; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglas Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.1 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 116.9 V/m; Power Drift = -0.559 dB Peak SAR (extrapolated) = 17.2 W/kg SAR(1 g) = 11.9 mW/g; SAR(10 g) = 8.56 mW/g Maximum value of SAR (measured) = 12.5 mW/g Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 224 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #86 (A86) Date Tested: 01/28/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 498.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 3 (Palm-Mic Kit); Type: 2-Wire Palm Mic w/ Earphone (P/N: KHS-8BL) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.0°C; Fluid Temp: 23.1°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 498 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 498 MHz; ı = 0.968 mho/m; İr = 58.1; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 13.9 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 117.1 V/m; Power Drift = -0.339 dB Peak SAR (extrapolated) = 17.9 W/kg SAR(1 g) = 12.4 mW/g; SAR(10 g) = 8.86 mW/g Maximum value of SAR (measured) = 13.0 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 225 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #87 (A87) Date Tested: 01/28/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 512.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 3 (Palm-Mic Kit); Type: 2-Wire Palm Mic w/ Earphone (P/N: KHS-8BL) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.0°C; Fluid Temp: 23.1°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 512 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 512 MHz; ı = 0.98 mho/m; İr = 57.9; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 13.0 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 107.1 V/m; Power Drift = -0.060 dB Peak SAR (extrapolated) = 17.7 W/kg SAR(1 g) = 12.1 mW/g; SAR(10 g) = 8.62 mW/g Maximum value of SAR (measured) = 12.7 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 226 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #88 (A88) Date Tested: 01/28/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 470.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 4 (Speaker-Microphone); Type: Slim-Line Speaker-Microphone (P/N: KMC-21) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.0°C; Fluid Temp: 23.1°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 470 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used: f = 470 MHz; ı = 0.93 mho/m; İr = 58.8; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 11.3 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 108.4 V/m; Power Drift = 0.054 dB Peak SAR (extrapolated) = 15.9 W/kg SAR(1 g) = 11 mW/g; SAR(10 g) = 7.89 mW/g Maximum value of SAR (measured) = 11.5 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 227 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #89 (A89) Date Tested: 01/28/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 484.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 4 (Speaker-Microphone); Type: Slim-Line Speaker-Microphone (P/N: KMC-21) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.0°C; Fluid Temp: 23.1°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 484 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 484 MHz; ı = 0.954 mho/m; İr = 58.5; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 13.3 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 121.6 V/m; Power Drift = -0.505 dB Peak SAR (extrapolated) = 19.1 W/kg SAR(1 g) = 13.1 mW/g; SAR(10 g) = 9.33 mW/g Maximum value of SAR (measured) = 13.8 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 228 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #90 (A90) Date Tested: 01/28/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 498.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 4 (Speaker-Microphone); Type: Slim-Line Speaker-Microphone (P/N: KMC-21) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.0°C; Fluid Temp: 23.1°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 498 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 498 MHz; ı = 0.968 mho/m; İr = 58.1; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 13.4 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 120.0 V/m; Power Drift = -0.347 dB Peak SAR (extrapolated) = 19.2 W/kg SAR(1 g) = 13.2 mW/g; SAR(10 g) = 9.38 mW/g Maximum value of SAR (measured) = 13.9 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 229 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #91 (A91) Date Tested: 04/06/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 498.0 MHz DUT: Kenwood NX-320-K; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 0320K124 Audio Accessory Category 4 (Speaker-Microphone); Type: Slim-Line Speaker-Microphone (P/N: KMC-21) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 21.0°C; Fluid Temp: 20.3°C; Barometric Pressure: 101.1 kPa; Humidity: 32% Communication System: CW Frequency: 498 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 498 MHz; ı = 0.954 mho/m; İr = 57.8; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglas Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.8 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 114.1 V/m; Power Drift = -0.253 dB Peak SAR (extrapolated) = 17.8 W/kg SAR(1 g) = 12.3 mW/g; SAR(10 g) = 8.81 mW/g Maximum value of SAR (measured) = 12.9 mW/g Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 230 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #92 (A92) Date Tested: 04/06/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 498.0 MHz DUT: Kenwood NX-320-K2; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 0320K218 Audio Accessory Category 4 (Speaker-Microphone); Type: Slim-Line Speaker-Microphone (P/N: KMC-21) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 21.0°C; Fluid Temp: 20.3°C; Barometric Pressure: 101.1 kPa; Humidity: 32% Communication System: CW Frequency: 498 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 498 MHz; ı = 0.954 mho/m; İr = 57.8; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglas Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.5 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 115.6 V/m; Power Drift = -0.277 dB Peak SAR (extrapolated) = 18.2 W/kg SAR(1 g) = 12.5 mW/g; SAR(10 g) = 8.95 mW/g Maximum value of SAR (measured) = 13.2 mW/g Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 231 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #93 (A93) Date Tested: 01/28/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 512.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 4 (Speaker-Microphone); Type: Slim-Line Speaker-Microphone (P/N: KMC-21) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.0°C; Fluid Temp: 23.1°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 512 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 512 MHz; ı = 0.98 mho/m; İr = 57.9; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.5 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 111.7 V/m; Power Drift = -0.268 dB Peak SAR (extrapolated) = 17.5 W/kg SAR(1 g) = 12.1 mW/g; SAR(10 g) = 8.62 mW/g Maximum value of SAR (measured) = 12.7 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 232 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #94 (A94) Date Tested: 01/28/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 470.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 4 (Speaker-Microphone); Type: Heavy Duty Speaker-Microphone (P/N: KMC-45) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.0°C; Fluid Temp: 23.1°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 470 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used: f = 470 MHz; ı = 0.93 mho/m; İr = 58.8; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.8 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 116.0 V/m; Power Drift = -0.223 dB Peak SAR (extrapolated) = 18.2 W/kg SAR(1 g) = 12.5 mW/g; SAR(10 g) = 8.94 mW/g Maximum value of SAR (measured) = 13.1 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 233 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #95 (A95) Date Tested: 01/28/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 484.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 4 (Speaker-Microphone); Type: Heavy Duty Speaker-Microphone (P/N: KMC-45) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.0°C; Fluid Temp: 23.1°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 484 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 484 MHz; ı = 0.954 mho/m; İr = 58.5; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 13.8 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 119.2 V/m; Power Drift = -0.461 dB Peak SAR (extrapolated) = 19.4 W/kg SAR(1 g) = 13.3 mW/g; SAR(10 g) = 9.49 mW/g Maximum value of SAR (measured) = 14.0 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 234 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #96 (A96) Date Tested: 04/06/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 484.0 MHz DUT: Kenwood NX-320-K; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 0320K124 Audio Accessory Category 4 (Speaker-Microphone); Type: Heavy Duty Speaker-Microphone (P/N: KMC-45) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 21.0°C; Fluid Temp: 20.3°C; Barometric Pressure: 101.1 kPa; Humidity: 32% Communication System: CW Frequency: 484 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 484 MHz; ı = 0.942 mho/m; İr = 58.1; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglas Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.5 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 115.9 V/m; Power Drift = -0.571 dB Peak SAR (extrapolated) = 17.1 W/kg SAR(1 g) = 11.8 mW/g; SAR(10 g) = 8.51 mW/g Maximum value of SAR (measured) = 12.4 mW/g Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 235 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #97 (A97) Date Tested: 04/06/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 484.0 MHz DUT: Kenwood NX-320-K2; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 0320K218 Audio Accessory Category 4 (Speaker-Microphone); Type: Heavy Duty Speaker-Microphone (P/N: KMC-45) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 21.0°C; Fluid Temp: 20.3°C; Barometric Pressure: 101.1 kPa; Humidity: 32% Communication System: CW Frequency: 484 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 484 MHz; ı = 0.942 mho/m; İr = 58.1; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglas Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.4 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 117.7 V/m; Power Drift = -0.508 dB Peak SAR (extrapolated) = 18.4 W/kg SAR(1 g) = 12.7 mW/g; SAR(10 g) = 9.09 mW/g Maximum value of SAR (measured) = 13.3 mW/g Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 236 of 361

/ m_ls_ _L 450 MHz Body SAR(x.y,z,f0) SAR; Z Sean:Value Along Z, X=0, Y=0 mW$ 0.04 0.06 0.08 0.10 0.14 KENWOOD

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #98 (A98) Date Tested: 01/28/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 498.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 4 (Speaker-Microphone); Type: Heavy Duty Speaker-Microphone (P/N: KMC-45) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.0°C; Fluid Temp: 23.1°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 498 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 498 MHz; ı = 0.968 mho/m; İr = 58.1; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.3 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 115.5 V/m; Power Drift = -0.467 dB Peak SAR (extrapolated) = 18.8 W/kg SAR(1 g) = 12.8 mW/g; SAR(10 g) = 9.14 mW/g Maximum value of SAR (measured) = 13.5 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 238 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #99 (A99) Date Tested: 01/28/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 512.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 4 (Speaker-Microphone); Type: Heavy Duty Speaker-Microphone (P/N: KMC-45) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.0°C; Fluid Temp: 23.1°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 512 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 512 MHz; ı = 0.98 mho/m; İr = 57.9; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.7 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 110.4 V/m; Power Drift = -0.291 dB Peak SAR (extrapolated) = 17.3 W/kg SAR(1 g) = 11.9 mW/g; SAR(10 g) = 8.48 mW/g Maximum value of SAR (measured) = 12.4 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 239 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #100 (A100) Date Tested: 01/31/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 470.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 4 (Speaker-Microphone); Type: Heavy Duty Speaker-Microphone (P/N: KMC-45) with Earphone Kit (P/N: KEP-2) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.1°C; Fluid Temp: 23.2°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 470 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used: f = 470 MHz; ı = 0.95 mho/m; İr = 58.6; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 11.8 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 110.9 V/m; Power Drift = -0.603 dB Peak SAR (extrapolated) = 17.5 W/kg SAR(1 g) = 11.8 mW/g; SAR(10 g) = 8.37 mW/g Maximum value of SAR (measured) = 12.5 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 240 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #101 (A101) Date Tested: 01/31/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 484.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 4 (Speaker-Microphone); Type: Heavy Duty Speaker-Microphone (P/N: KMC-45) with Earphone Kit (P/N: KEP-2) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.1°C; Fluid Temp: 23.2°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 484 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 484 MHz; ı = 0.964 mho/m; İr = 59.4; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.1 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 118.8 V/m; Power Drift = -0.455 dB Peak SAR (extrapolated) = 19.2 W/kg SAR(1 g) = 13.2 mW/g; SAR(10 g) = 9.41 mW/g Maximum value of SAR (measured) = 13.8 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 241 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #102 (A102) Date Tested: 01/31/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 498.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 4 (Speaker-Microphone); Type: Heavy Duty Speaker-Microphone (P/N: KMC-45) with Earphone Kit (P/N: KEP-2) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.1°C; Fluid Temp: 23.2°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 498 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 498 MHz; ı = 0.978 mho/m; İr = 59.5; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 13.5 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 115.3 V/m; Power Drift = -0.175 dB Peak SAR (extrapolated) = 19.7 W/kg SAR(1 g) = 13.4 mW/g; SAR(10 g) = 9.45 mW/g Maximum value of SAR (measured) = 14.0 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 242 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #103 (A103) Date Tested: 04/06/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 498.0 MHz DUT: Kenwood NX-320-K; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 0320K124 Audio Accessory Category 4 (Speaker-Microphone); Type: Heavy Duty Speaker-Microphone (P/N: KMC-45) with Earphone Kit (P/N: KEP-2) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 21.0°C; Fluid Temp: 20.3°C; Barometric Pressure: 101.1 kPa; Humidity: 32% Communication System: CW Frequency: 498 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 498 MHz; ı = 0.954 mho/m; İr = 57.8; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection (Locations From Previous Scan Used))Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglas Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.4 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 117.0 V/m; Power Drift = -0.560 dB Peak SAR (extrapolated) = 17.9 W/kg SAR(1 g) = 12.4 mW/g; SAR(10 g) = 8.88 mW/g Maximum value of SAR (measured) = 12.9 mW/g Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 243 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #104 (A104) Date Tested: 04/06/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 498.0 MHz DUT: Kenwood NX-320-K2; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 0320K218 Audio Accessory Category 4 (Speaker-Microphone); Type: Heavy Duty Speaker-Microphone (P/N: KMC-45) with Earphone Kit (P/N: KEP-2) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 21.0°C; Fluid Temp: 20.3°C; Barometric Pressure: 101.1 kPa; Humidity: 32% Communication System: CW Frequency: 498 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 498 MHz; ı = 0.954 mho/m; İr = 57.8; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglas Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.3 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 116.6 V/m; Power Drift = -0.471 dB Peak SAR (extrapolated) = 18.3 W/kg SAR(1 g) = 12.6 mW/g; SAR(10 g) = 8.99 mW/g Maximum value of SAR (measured) = 13.3 mW/g Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 244 of 361

Dates of Evaluation (K3) Test Report Serial No. Test Report Revision No. Jan. 4,6,26-28,31, 2011 121510ALH-T1070-S90U Rev. 1.3 (4th Release) Test Report Issue Date Dates of Evaluation (K/K2) Description of Test(s) RF Exposure Category April 14, 2011 March 30 - April 7, 2011 Specific Absorption Rate Occupational (Controlled) Test Lab Certificate No. 2470.01 Audio Accessory SAR Plot #105 (A105) Date Tested: 01/31/2011 Body-worn SAR - KRA-27M2 “Antenna D” - KNB-56N 1400mAh Ni-MH “Battery c” – 512.0 MHz DUT: Kenwood NX-320-K3; Type: Portable FM UHF-H PTT Radio Transceiver; Serial: No. 10 Audio Accessory Category 4 (Speaker-Microphone); Type: Heavy Duty Speaker-Microphone (P/N: KMC-45) with Earphone Kit (P/N: KEP-2) Body-worn Accessory 1: Belt-Clip (P/N: KBH-12) Ambient Temp: 24.1°C; Fluid Temp: 23.2°C; Barometric Pressure: 101.1 kPa; Humidity: 40% Communication System: CW Frequency: 512 MHz; Duty Cycle: 1:1 3 Medium: M450 Medium parameters used (interpolated): f = 512 MHz; ı = 0.98 mho/m; İr = 58.2; ȡ = 1000 kg/m - Probe: ET3DV6 - SN1590; ConvF(7.73, 7.73, 7.73); Calibrated: 15/07/2010 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 27/04/2010 - Phantom: Barski Industries; Type: Fiberglass Planar; Serial: 03-01 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Body-worn SAR – 1.7 cm Belt-Clip Spacing from Back of DUT to Planar Phantom Area Scan (8x19x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 11.7 mW/g Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 111.3 V/m; Power Drift = -0.250 dB Peak SAR (extrapolated) = 17.8 W/kg SAR(1 g) = 12.2 mW/g; SAR(10 g) = 8.65 mW/g Maximum value of SAR (measured) = 12.8 mW/g  Applicant: Kenwood USA Corporation FCC ID: ALH431000 DUT Models: NX-320-K/K2/K3 DUT Type: Portable UHF-H PTT Radio Transceiver Transmitter Frequency Range: 450.0 - 512.0 MHz 2011 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 245 of 361


Document Created: 2011-04-15 10:18:44
Document Modified: 2011-04-15 10:18:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC