05 (Short-Term Confidential) User Manual

FCC ID: AK8XMGS6DSP

Users Manual

Download: PDF
FCCID_3631189

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Cover XMGS6DSPUC\010COV.fm 010COV.book Page 1 Wednesday, November 1, 2017 4:28 PM 4-733-364-11(1) 6/5 Channel Operating Instructions GB Class-D Amplifier Mode d’emploi FR with DSP Manual de instrucciones ES TH Owner’s Record The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. XM-GS6DSP Serial No. XM-GS6DSP XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Left XMGS6DSPUC\020INT.fm 010COV.book Page 2 Wednesday, November 1, 2017 4:27 PM This device complies with Part 15 of the FCC Rules To use the unit safely, see “Installation and and Industry Canada's licence-exempt RSSs. Connections” (page 6) for details. Operation is subject to the following two conditions: The nameplate indicating operating voltage, etc., is (1) This device may not cause interference; and located on the bottom of the chassis. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Warning This transmitter must not be co-located or operated in conjunction with any other antenna or FOR THE CUSTOMERS IN THE USA. NOT transmitter. APPLICABLE IN CANADA, INCLUDING IN THE Under Industry Canada regulations, this radio PROVINCE OF QUEBEC. transmitter may only operate using an antenna of a POUR LES CLIENTS AUX ÉTATS-UNIS. NON type and maximum (or lesser) gain approved for APPLICABLE AU CANADA, Y COMPRIS LA the transmitter by Industry Canada. To reduce PROVINCE DE QUÉBEC. potential radio interference to other users, the antenna type and its gain should be so chosen that This equipment has been tested and found to the equivalent isotropically radiated power (e.i.r.p.) comply with the limits for a Class B digital device, is not more than that necessary for successful pursuant to Part 15 of the FCC Rules. communication. These limits are designed to provide reasonable protection against harmful interference in a This equipment complies with FCC/IC radiation residential installation. This equipment exposure limits set forth for an uncontrolled generates, uses, and can radiate radio frequency environment and meets the FCC radio frequency energy and, if not installed and used in (RF) Exposure Guidelines and RSS-102 of the IC accordance with the instructions, may cause radio frequency (RF) Exposure rules. This harmful interference to radio communications. equipment has very low levels of RF energy that is However, there is no guarantee that interference deemed to comply without maximum permissive will not occur in a particular installation. If this exposure evaluation (MPE). equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. 2GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Right XMGS6DSPUC\020INT.fm 010COV.book Page 3 Wednesday, November 1, 2017 4:27 PM Important notice Caution IN NO EVENT SHALL SONY BE LIABLE FOR ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR OTHER DAMAGES INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT, DOWNTIME, AND PURCHASER’S TIME RELATED TO OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS HARDWARE AND/OR ITS SOFTWARE. Dear customer, this product includes a radio transmitter. Please check your vehicle operation manual or contact the manufacturer of your vehicle or your vehicle dealer, before you install this product into your vehicle. Emergency calls This BLUETOOTH car handsfree and the electronic device connected to the handsfree operate using radio signals, cellular, and landline networks as well as user-programmed function, which cannot guarantee connection under all conditions. Therefore do not rely solely upon any electronic device for essential communications (such as medical emergencies). On BLUETOOTH communication  Microwaves emitting from a BLUETOOTH device may affect the operation of electronic medical devices. Turn off this unit and other BLUETOOTH devices in the following locations, as it may cause an accident. – where inflammable gas is present, in a hospital, train, airplane, or petrol station – near automatic doors or a fire alarm  This unit supports security capabilities that comply with the BLUETOOTH standard to provide a secure connection when the BLUETOOTH wireless technology is used, but security may not be enough depending on the setting. Be careful when communicating using BLUETOOTH wireless technology.  We do not take any responsibility for the leakage of information during BLUETOOTH communication. If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer. 3GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Left XMGS6DSPUC\030TOC.fm 010COV.book Page 4 Wednesday, November 1, 2017 4:27 PM Features Table of Contents  Sony 5-speaker system with 4.1ch DSP connection Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 supported. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  Sony 3-way component speaker connection supported.  Bluetooth® connection with your iPhone/ Operation Android™ smartphone supported. Location and Function of Controls . . . . . . . . . . . . . 5  Maximum power output of 100 W per channel (FRONT/REAR at 4 Ω) and 300 W per channel (SUB at 4 Ω). Installation and Connections  This unit can be used as a bridging amplifier with Parts for Installation and Connections . . . . . . . . . . 6 a maximum output of 1,100 W (SUB at 2 Ω). Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  Built-in LPF (low-pass filter) (REAR/SUB), HPF Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 (high-pass filter) (FRONT/REAR), and Low boost Power connections . . . . . . . . . . . . . . . . . . . . . . . 8 circuit (SUB). REMOTE connections . . . . . . . . . . . . . . . . . . . . . 9  Protection circuit and indicator provided. Input connections. . . . . . . . . . . . . . . . . . . . . . . 10  Direct connection can be made with the speaker output of your car audio unit if that is not Speaker connections . . . . . . . . . . . . . . . . . . . . 14 equipped with the line output (High level input connection). BLUETOOTH  Hi-level Sensing Power On feature allows this unit Preparing a BLUETOOTH Device . . . . . . . . . . . . . . 15 to be activated without the need for a REMOTE connection. Pairing and connecting with a BLUETOOTH  Pulse power supply* for stable and regulated device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 output power. Connecting with a paired BLUETOOTH device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 * Pulse power supply Playing a BLUETOOTH Device . . . . . . . . . . . . . . . . 16 This unit has a built-in power regulator which converts the power supplied by the 12 V DC car battery into high speed pulses using a semiconductor Settings switch. These pulses are stepped up by the built-in pulse transformer and separated into both positive DSP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 and negative power supplies before being converted Sony | Music Center with iPhone/Android into direct current again. This is to regulate smartphone . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 fluctuating voltage from the car battery. This light- Establishing the Sony | Music Center weight power supply system provides a highly efficient power supply with a low impedance output. connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Configuring the DSP settings . . . . . . . . . . . . . 17 Additional Information Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 About iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Fuse replacement . . . . . . . . . . . . . . . . . . . . . . . 19 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Support Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Right XMGS6DSPUC\040CD.fm 010COV.book Page 5 Wednesday, November 1, 2017 4:27 PM Operation Location and Function of Controls Control panel side Connector panel side  POWER/PROTECTOR indicator (green)  SELECT (input select) switch – Lights up when the unit is turned on. Selects “2ch/BT” or “6ch” mode depending on – Flashes when the unit detects an abnormality. the use/non-use of the DSP. When selecting the See “Troubleshooting” (page 21) for solutions “2ch/BT” mode, also select the sensitivity “2V” to problems. or “5V” depending on the pre-output level of your car audio unit (page 10).  PAIRING button Press and hold for 2 seconds to enter the pairing TWEETER/FRONT (tweeter/front speaker) standby mode. section: Press and hold for 7 seconds to turn off the  HIGH PASS FILTER switch BLUETOOTH functions (BLUETOOTH off mode). Turns the high-pass filter on/off. (Available only when the SELECT switch is set to the “2V” or “5V” position.)  HIGH PASS FILTER control Adjusts the cut-off frequency (500 Hz – 4 kHz).  (BLUETOOTH) indicator (blue) – Flashes quickly in pairing standby mode.  LEVEL control – Flashes slowly in BLUETOOTH standby mode. Adjusts the input level (0.3 V – 6 V). Turn it – Lights up when BLUETOOTH connection is clockwise when the output level of the audio established. device seems low.  RESET button Resets the unit to the factory defaults (the DSP settings and BLUETOOTH pairing information stored on the unit are also erased). Press with a pointed object such as a ballpoint pen. 5GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Left XMGS6DSPUC\040CD.fm 010COV.book Page 6 Wednesday, November 1, 2017 4:27 PM MID/REAR (midrange/rear speaker) section:  FILTER switch Selects “HPF” (high-pass filter) or “HPF+LPF” Installation and Connections (high-pass and low-pass filters) according to the speaker system. Parts for Installation and  LOW PASS FILTER control Adjusts the cut-off frequency (500 Hz – 4 kHz). Connections  HIGH PASS FILTER control   Adjusts the cut-off frequency (50 Hz – 500 Hz). ø5 × 20 mm (7/32 × 13/16 in)  LEVEL control Adjusts the input level (0.3 V – 6 V). Turn it clockwise when the output level of the audio ×4 device seems low. WOOFER/SUBWOOFER (woofer/subwoofer)   section:  LOW PASS FILTER switch Turns the low-pass filter on/off.  LOW PASS FILTER control Adjusts the cut-off frequency (50 Hz – 500 Hz).   LOW BOOST control Boosts the frequencies around 40 Hz to a maximum of 10 dB (0 dB – 10 dB).  LEVEL control Adjusts the input level (0.3 V – 6 V). Turn it clockwise when the output level of the audio This parts list does not include all the package device seems low. contents.  LINE INPUT connector  HIGH LEVEL INPUT connector  REMOTE IN jack For a wired remote control (not supplied) SPEAKER OUT section:  TWEETER/FRONT/MID/REAR connector  WOOFER/SUBWOOFER terminals POWER section:  Fuse (30 A)  ACC (accessary) terminal +12V terminal GND (ground (earth)) terminal 6GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Right XMGS6DSPUC\040CD.fm 010COV.book Page 7 Wednesday, November 1, 2017 4:27 PM Installation Connections  Select the mounting location where it is easy to  Before making any connections, disconnect the press the PAIRING button on the unit. ground (earth) terminal of the car battery to avoid  Choose the mounting location carefully so the short circuits. unit will not interfere with the normal movements  Be sure to use speakers with an adequate power of the driver and it will not be exposed to direct rating. If you use small capacity speakers, they sunlight or hot air from the heater. may be damaged.  Do not mount the unit in a confined space such as  Do not connect the  terminal of the speaker under the floor carpet that will obstruct heat system to the car chassis, and do not connect the dissipation.  terminal of the right speaker with that of the left speaker. Mounting the unit  Install the input and output cords away from the First, place the unit where you plan to install it, and power supply wire. Running them close together mark the positions of the 4 screw holes on a may generate interference noise. mounting board (not supplied). Then drill a 3 mm  This unit is a high powered amplifier. Therefore, it (1/8 in) pilot hole at each mark and mount the unit may not perform to its full potential if used with onto the board with the supplied mounting screws. the speaker cords supplied with the car. The mounting screws are all 20 mm (13/16 in) long,  If your car is equipped with a computer system for so make sure that the mounting board is thicker navigation or some other purpose, do not remove than 20 mm (13/16 in). the ground (earth) wire from the car battery. If you disconnect the wire, the computer memory may be erased. To avoid short circuits when making  connections, disconnect the +12 V power supply wire until all the other wires have been connected. Making the terminal connections Pass the wires through the cap, connect the wires, then cover the terminals with the cap.   Note When you tighten a screw, be careful not to apply too much torque as doing so may damage the screw (the torque value should be less than 1 N•m). 7GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Left XMGS6DSPUC\040CD.fm 010COV.book Page 8 Wednesday, November 1, 2017 4:27 PM Making power connections Power connections Power connection wires (not supplied) are required.  Connect the +12 V power supply wire only after all the other wires have been connected.  Be sure to connect the ground (earth) wire of the unit securely to a metal point of the car. A loose connection may cause a malfunction of the amplifier.  When using a car audio unit without a remote output (REMOTE OUT) for the amplifier, connect the remote input (REM) terminal to the accessory power supply.  Use a power supply wire with a fuse (60 A) attached.  All power wires connected to the positive battery to a metal point of the car post should be fused within 450 mm (17 3/4 in) of less than 450 mm (17 3/4 in) the battery post, and before they pass through any metal.  Make sure that the car’s battery wires connected Fuse (60 A) to the car (ground (earth) to chassis) are of a wire gauge at least equal to that of the main power +12 V car battery wire connected from the battery to the amplifier.  During full-power operation, a current of more to the car’s ACC power line than 60 A will run through the system. Therefore, make sure that the wires to be connected to the +12 V and GND terminals of this unit are at least * Ground (earth) to chassis. 8-Gauge (AWG-8) or have a sectional area of more than 8 mm² (11/32 in²). 8GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Right XMGS6DSPUC\040CD.fm 010COV.book Page 9 Wednesday, November 1, 2017 4:27 PM REMOTE connections When your car’s ignition has no ACC position For the line input connections  (page 10),  Connect the remote out (REMOTE OUT) from your (page 11) or  (page 11) only. car audio unit to the ACC terminal, and connect Connect the remote out (REMOTE OUT) from your the remote out (REMOTE OUT) from your car audio car audio unit to the appropriate position. unit to the remote input (REM) terminal via the high level input connector  (sky blue lead ). When your car’s ignition has an ACC position Sky blue  Connect the remote out (REMOTE OUT) from your car audio unit to the remote input (REM) terminal via the high level connector  (sky blue lead ), and connect the ACC terminal to the car’s ACC power line.  Sky blue   * With this connection, a BLUETOOTH device cannot be played while the car audio is turned off. If your car audio unit has no REMOTE OUT Connect the high level input connector . to the car’s ACC power line  * The REMOTE connection is not necessary when making the high level input connection  (page 12),  (page 12) and  (page 13). If your car audio unit has no REMOTE OUT Connect the ACC terminal to the ACC power line, and connect the remote input (REM) terminal to the ACC power line via the high level input connector  (sky blue lead ).  REM to the car’s ACC power line Sky blue  9GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Left XMGS6DSPUC\040CD.fm 010COV.book Page 10 Wednesday, November 1, 2017 4:27 PM *1 While a bridged subwoofer connection is made, this Input connections unit functions as a 5ch amplifier. *2 When adjusting the volume balance of the front Set the SELECT switch to the appropriate position speakers, rear speakers and subwoofer while the according to the speaker system. unit is in 2ch mode (DSP mode), operate your iPhone/Android smartphone to adjust the [Fader], 2ch/BT mode and 6ch mode [Balance] and [Subwoofer Level] settings of the Select “2ch/BT” or “6ch” mode depending on the “Sony | Music Center” application. use/non-use of the DSP. *3 The sound settings of the DSP (page 17) can be made When selecting the “2ch/BT” mode, also select the by the “Sony | Music Center” application on the sensitivity “2V” or “5V” depending on the pre- iPhone/Android smartphone. Before setting, operate your iPhone/Android smartphone to output level of your car audio unit. establish the BLUETOOTH connection with this unit (page 15). Mode For  using this unit as a 6ch amplifier (no  Line input connection built-in DSP is used)*1. For details on the connections, see: (with DSP enabled/2ch mode) – “ Line input connection (for With the speaker connection  (page 14) Subwoofer BTL system/6ch mode)” (page 11). – “ High level input connection (for 6ch (Through mode) Subwoofer BTL system/6ch mode)” (page 12).  using this unit with a 3-way speaker system. With this connection, a 3-ways speaker system can be driven without a crossover network. For details on the connections, see: – “ Line input connection (for 3-way speaker system/6ch mode)” (page 11). – “ High level input connection (for  3-way speaker system/6ch mode)” (page 13).  encoding 2ch input signals into 4.1ch output signals (the built-in DSP is 2ch/BT (DSP mode)*2*3 used). For details on the connections, Notes see:  When making this connection, set the SELECT switch – “ Line input connection (with DSP to the “2V” position. enabled/2ch mode)” (page 10).  Set the SELECT switch to the “5V” position if the – “ High level input connection (with sound is distorted when increasing the volume of the car audio unit (only for car audio unit with a pre- DSP enabled/2ch mode)” (page 12). output level of 5 V).  playing a BLUETOOTH device by operating the “Sony | Music Center” application. For details, see “Playing a BLUETOOTH Device” (page 16). Setting the sensitivity “2V” or “5V” of the 2V “2ch/BT” mode. Normally, use this unit set to “2V”. When using a car audio unit with a high pre-output level, set to “5V” if the sound 5V is distorted while increasing the volume. 10GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Right XMGS6DSPUC\040CD.fm 010COV.book Page 11 Wednesday, November 1, 2017 4:27 PM  Line input connection  Line input connection (for Subwoofer BTL system/6ch mode) (for 3-way speaker system/6ch mode) With the speaker connection  or  (page 14, 14) With the speaker connection  (page 15) RCA splitter cable (not supplied)   Notes  When making this connection, set the SELECT switch to the “6ch” position. Note  Make sure the signal to SUB AUDIO IN is monaural. When making this connection, set the SELECT switch to SUB AUDIO IN of this unit does not support stereo the “6ch” position. signal input. * Use an RCA splitter cable (not supplied) to branch the signals from REAR AUDIO OUT to REAR AUDIO IN and SUB AUDIO IN. 11GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Left XMGS6DSPUC\040CD.fm 010COV.book Page 12 Wednesday, November 1, 2017 4:27 PM  High level input connection  High level input connection (with DSP enabled/2ch mode) (for Subwoofer BTL system/6ch mode) With the speaker connection  (page 14) With the speaker connection  or  (page 14, 14) White Front speaker output (left) White Front speaker output (left) White/striped White/striped Gray Front speaker Gray Front speaker output (right) output (right) Gray/striped Gray/striped Green Rear speaker  output (left) Green/striped Purple Rear speaker output (right) Purple/striped Brown Sky blue Subwoofer output Brown/(black) striped Brown/(blue) striped  Note If subwoofer outputs are not equipped to your car audio unit, use this unit as a 4ch amplifier, or make the connection in 2ch mode () instead. 12GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Right XMGS6DSPUC\040CD.fm 010COV.book Page 13 Wednesday, November 1, 2017 4:27 PM  High level input connection High level input cord connection (for 3-way speaker system/6ch mode) Connect the cords properly to speakers. With the speaker connection  (page 15) er er  White ak ak t ) 1 s pe eft) s pe igh FL Front speaker (left) t (l on t t (r on t 2  White/striped Fr tpu Fr tpu ou ou 3  Gray FR Front speaker (right) 4  Gray/striped 5  Green RL Rear speaker (left) 6  Green/striped 7  Purple n RR Rear speaker (right) ee 8  Purple/striped ay Gr te Gr  Brown hi d 9 W pe d ed tri SL Subwoofer (left) pe rip /s  Brown/(black) tri st en 10 /s a y/ re striped ti e Gr G h W 11  Sky blue SR Subwoofer (right) Brown/(blue) e 12  lu striped n yb le ow Sk rp Br Pu ) e) ck lu d la (b pe (b n/ tri n/ ow d /s ow d Br ripe le Br ripe u rp st P st  13GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Left XMGS6DSPUC\040CD.fm 010COV.book Page 14 Wednesday, November 1, 2017 4:27 PM Speaker connections  2-way speaker system with a bridged subwoofer connection Set the HIGH PASS FILTER switch, FILTER switch and With the input connection  or  (page 10, 11) LOW PASS FILTER switch on the control panel to the appropriate positions according to the speaker Tweeter (min. 4 Ω) system. Also, refer to the manual supplied with your speakers for further details. Woofer (min. 4 Ω)  4.1ch speaker system with a bridged subwoofer connection FILTER OFF With the input connection  or  (page 10, 11) HIGH PASS FILTER LOW PASS FILTER Front speaker (min. 4 Ω) OFF ON HPF HPF + OFF ON  LPF Rear speaker (min. 4 Ω) BTL FILTER OFF HIGH PASS FILTER LOW PASS FILTER OFF ON HPF HPF OFF ON +  LPF Subwoofer (min. 2 Ω) Note When making this connection, set the filter switches to the following positions: – HIGH PASS FILTER: ON – FILTER: HPF+LPF BTL – LOW PASS FILTER: ON Subwoofer (min. 2 Ω) Notes  When making this connection, set the filter switches to the following positions: – HIGH PASS FILTER: OFF – FILTER: OFF – LOW PASS FILTER: ON  When adjusting the volume balance of the front speakers, rear speakers and subwoofer while the unit is in 2ch mode (DSP mode), operate your iPhone/ Android smartphone to adjust the [Fader], [Balance] and [Subwoofer Level] settings of the “Sony | Music Center” application. 14GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Right XMGS6DSPUC\040CD.fm 010COV.book Page 15 Wednesday, November 1, 2017 4:27 PM  3-way speaker system With the input connection  (page 11) Using Sony 3 Way Component Speaker System BLUETOOTH XS-GS1631C is recommended. Tweeter (min. 4 Ω) Preparing a BLUETOOTH Device You can enjoy music on a BLUETOOTH compatible device such an iPhone/Android smartphone Midrange speaker (min. 4 Ω) (hereafter “BLUETOOTH device” if not otherwise specified). For details on connecting, refer to the operating instructions supplied with the device. Before connecting the device, turn down the FILTER HIGH PASS FILTER OFF LOW PASS FILTER volume of the BLUETOOTH device; otherwise, a loud sound may result. OFF ON HPF HPF OFF ON + (Available only when the SELECT switch is set to the  LPF “2V” or “5V” position.) Pairing and connecting with a BLUETOOTH device When connecting a BLUETOOTH device for the first time, mutual registration (called “pairing”) is required. Pairing enables this unit and other devices Woofer (min. 2 Ω) to recognize each other. Note When making this connection, set the filter switches to the following positions: – HIGH PASS FILTER: ON – FILTER: HPF+LPF – LOW PASS FILTER: ON 1 Place the BLUETOOTH device within 1 m (3 ft) of this unit. Speaker cord connection Connect the cords properly to speakers. 2 Press and hold PAIRING for 2 seconds. The indicator flashes quickly while the unit is in pairing standby mode. 3 Perform pairing on the BLUETOOTH device so it detects this unit. 4 Select [XM-GS6DSP] shown in the display of the BLUETOOTH device. 1  White If your model name does not appear, repeat FL Front speaker (left) from step 2. 2  White/striped 3 FR Front speaker (right)  Gray 5 If passkey input is required on the 4  Gray/striped BLUETOOTH device, input [0000]. 5  Green When pairing is made, the indicator flashes RL Rear speaker (left) slowly. 6  Green/striped 7  Purple 6 Select this unit on the BLUETOOTH device RR Rear speaker (right) 8  Purple/striped to make the BLUETOOTH connection. The indicator lights up when the connection is established. Note While connected to a BLUETOOTH device, this unit cannot be detected from another device. To enable detection, press PAIRING to enter the pairing standby mode and search for this unit from another device. 15GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Left XMGS6DSPUC\040CD.fm 010COV.book Page 16 Wednesday, November 1, 2017 4:27 PM To start playback To adjust the volume For details, see “Playing a BLUETOOTH Device” During playback, adjust the volume of your iPhone/ (page 16). Android smartphone, or adjust the sound settings of the “Sony | Music Center” application. To disconnect the paired device Perform step 2. To switch to the line input connection (in 2ch mode) Select [Audio In] on the “Sony | Music Center” Connecting with a paired BLUETOOTH application. device To turn off the BLUETOOTH functions To use this unit with BLUETOOTH, connection with a Press and hold PAIRING for 7 seconds. paired device is required. Some paired devices will The BLUETOOTH pairing information stored on the connect to this unit automatically. unit is erased. Tip If the car’s ignition is turned off while the BLUETOOTH connection is established, this unit reconnects automatically to the last-connected BLUETOOTH device when the car’s ignition is turned to on. Operate the BLUETOOTH device to make the BLUETOOTH connection with this unit (page 15). Playing a BLUETOOTH Device You can play contents on a connected BLUETOOTH device that supports BLUETOOTH A2DP (Advanced Audio Distribution Profile). (Available only when the SELECT switch is set to the “2V” or “5V” position.) To play the BLUETOOTH device, installing the “Sony | Music Center” application to your iPhone/ Android smartphone is required. Download the latest version of “Sony | Music Center” application from the App Store for iPhone or from Google Play for Android smartphone. 1 Operate the BLUETOOTH device to make the BLUETOOTH connection with this unit (page 15). 2 Launch the “Sony | Music Center” application. 3 Start up your audio playback application on the BLUETOOTH device. 4 Operate the BLUETOOTH device to start playback. 16GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Right XMGS6DSPUC\040CD.fm 010COV.book Page 17 Wednesday, November 1, 2017 4:27 PM Establishing the Sony | Music Center Settings connection 1 Make the BLUETOOTH connection with DSP Settings your iPhone/Android smartphone You can configure the DSP settings using the (page 15). “Sony | Music Center” application with the “Advanced car audio setting” app embedded in as a 2 Launch the “Sony | Music Center” plug-in. application. (Available only when the SELECT switch is set to the Connection to iPhone/Android smartphone “2V” or “5V” position.) starts. For details on the operations on iPhone/ Android smartphone, see the Help of the Sony | Music Center with iPhone/ application. Android smartphone If the device number appears Downloading the latest version of the “Sony | Make sure that the number is displayed (e.g., Music Center” application is required from the App 123456), then select [Yes] on the iPhone/Android Store for iPhone or from Google Play for Android smartphone. smartphone. Notes Configuring the DSP settings  For your safety, follow your local traffic laws and regulations, and do not operate the application while driving. 1 Operate your iPhone/Android  “Sony | Music Center” is an app for controlling Sony smartphone to activate the “Sony | audio devices which are compatible with “Sony | Music Center” application, then touch Music Center”, by your iPhone/Android smartphone. the [Settings] icon.  What you can control with “Sony | Music Center” Alternatively, touch [Advanced car audio varies depending on the connected device.  To make use of “Sony | Music Center” features, see setting] to enter the setting mode. the details on your iPhone/Android smartphone.  For further details on “Sony | Music Center,” visit the 2 Tap [Sound]. following URL: http://www.sony.net/smcqa/  Visit the website below and check the compatible 3 Tap the desired setup item, then make iPhone/Android smartphone models. the sound settings. For iPhone: visit the App Store For Android smartphone: visit Google Play The following items can be set. About the “Advanced car audio setting” Equalizer (equalizer) application Selects an equalizer curve from 10 equalizer “Advanced car audio setting” is a plug-in curves or off: application enabling you to configure further sound [Off], [R&B], [Rock], [Pop], [Hip-Hop], [EDM], settings by the “Sony | Music Center” application. [Jazz], [Soul], [Country], [Karaoke], [Custom]. Downloading the latest version of the “Advanced The equalizer curve setting can be memorized car audio setting” application is required from the for each source. App Store for iPhone or from Google Play for Android smartphone. * [Karaoke] reduces the vocal sound but cannot fully remove it during playback. Also, using a microphone is not supported. 17GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Left XMGS6DSPUC\040CD.fm 010COV.book Page 18 Wednesday, November 1, 2017 4:27 PM Listening Position (listening position) Additional Information Precautions  This unit is designed for negative ground (earth) 12 V DC operation only.  Use speakers with an impedance of 2 Ω to 8 Ω Front/Rear Position (front/rear position) (SUB), and 4 Ω to 8 Ω (FRONT/REAR). Simulates a natural sound field by delaying the  Do not connect any active speakers (with built-in sound output from speakers to suit your amplifiers) to the speaker terminals of the unit. position: Doing so may damage the active speakers.  [Front Left] (front left),  Avoid installing the unit in areas subject to:  [Front Right] (front right), – high temperatures such as from direct sunlight  [Front] (center front), or hot air from the heater  [All] (center of your car), – rain or moisture [Custom] (position set by “Advanced car audio – dust or dirt. setting” of “Sony | Music Center”)  If your car is parked in direct sunlight and there is [OFF] (no position set) a considerable rise in temperature inside the car, Adjust Position (adjust position) allow the unit to cool down before use. Fine-tunes the listening position setting: [+3] –  When installing the unit horizontally, be sure not [Center] – [-3]. to cover the fins with the floor carpet, etc. (Available only when [Front/Rear Position] is not  If this unit is placed too close to the car audio unit set to [Off] or [Custom].) or antenna (aerial), interference may occur. In this Subwoofer Position (subwoofer position) case, relocate this unit away from the car audio  [Near] (near), unit or antenna (aerial).  [Normal] (normal),  If no power is being supplied to the car audio  [Far] (far) unit, check the connections. (Available only when [Front/Rear Position] is not  This power amplifier employs a protection circuit* set to [Off] or [Custom].) to protect the transistors and speakers if the amplifier malfunctions. Do not attempt to test the Balance (balance) protection circuits by covering the heat sink or Adjusts the sound balance: [15] – [0] – [-15]. connecting improper loads. Alternatively, adjust the setting point to the left/  Do not use the unit on a weak battery as its right in the “BAL/FAD/SW Level” setting of optimum performance depends on a good power “Advanced car audio setting”. supply.  For safety, keep your car audio unit volume Fader (fader) moderate so that you can still hear other sounds. Adjusts the relative level: [15] – [0] – [-15]. Alternatively, adjust the setting point to up/ * Protection circuit down in the “BAL/FAD/SW Level” setting of This amplifier is provided with a protection circuit that “Advanced car audio setting”. operates in the following cases: – when the unit overheats – when a DC current is generated Subwoofer Level (subwoofer level) – when the speaker terminals are short-circuited. Adjusts the subwoofer volume level: [-11.0] – The POWER/PROTECTOR indicator will blink, and the [0.0] – [10.0]. unit will shut down. If this happens, take out the Alternatively, touch SW Level +/– in the “BAL/ cassette tape or disc, turn off the connected FAD/SW Level” setting of “Advanced car audio equipment, and determine the cause of the setting”. malfunction. If the unit has overheated, wait until it cools down before use. If you have any questions or problems concerning your unit that are not covered in this manual, please consult your nearest Sony dealer. 18GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Right XMGS6DSPUC\040CD.fm 010COV.book Page 19 Wednesday, November 1, 2017 4:27 PM About iPod Maintenance  You can connect to the following iPod models. Update your iPod devices to the latest software before use. Fuse replacement Compatible iPhone/iPod models When replacing the fuse, be sure to use one matching the amperage stated above the fuse Compatible Model Bluetooth® holder. If the fuse blows, check the power iPhone 8 Plus  connection and replace both the fuses. If the fuse iPhone 8  blows again after replacement, there may be an internal malfunction. In such a case, consult your iPhone 7 Plus  nearest Sony dealer. iPhone 7  iPhone SE  iPhone 6s Plus  iPhone 6s  iPhone 6 Plus  iPhone 6  iPhone 5s  iPhone 5c  Warning Never use a fuse with an amperage rating iPhone 5  exceeding the one supplied with the unit as this iPhone 4s  could damage the unit. iPod touch (6th generation)  iPod touch (5th generation)   “Made for iPod,” and “Made for iPhone,” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance. If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer. 19GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Left XMGS6DSPUC\040CD.fm 010COV.book Page 20 Wednesday, November 1, 2017 4:27 PM Maximum output: Specifications 5 Speakers: 100 W × 4 (FRONT/REAR at 4 Ω), 1,100 W × 1 (SUB BTL at 2 Ω) AUDIO POWER SPECIFICATIONS 6 Speakers: CTA2006 Standard 100 W × 4 (FRONT/REAR at 4 Ω), Power Output: 45 Watts RMS × 4 at 4 300 W × 2 (SUB at 2 Ω) Ohms, 90 Watts RMS × 2 at 4 Ohms < 1% Rated output (supply voltage at 14.4 V, 20 Hz – THD+N 20 kHz, 1% THD): SN Ratio: 83 dBA (FRONT/REAR), 80 dBA (SUB) (reference: 1 Watt into 4 Ohms) 6 Speakers: 45 W × 4 (FRONT/REAR at 4 Ω), Wireless Communication 90 W × 2 (SUB at 4 Ω) Frequency response: Communication System: BLUETOOTH Standard version 3.0 20 Hz – 20 kHz ( +0.5 −3.0 dB) (FRONT/REAR), Output: 20 Hz – 10 kHz ( +0.5 −3.0 dB) (SUB) BLUETOOTH Standard Power Class 2 Harmonic distortion: (Max. Conducted +1 dBm) 0.1% at 1 W, 1 kHz (FRONT/REAR at 4 Ω), Maximum communication range*1: 0.08% or less at 45 W, 1 kHz (SUB at 4 Ω) Line of sight approx. 10 m (33 ft) Low-pass filter: Frequency band: 500 Hz – 4 kHz, 12 dB/oct (REAR), 2.4 GHz band 50 Hz – 500 Hz, 12 dB/oct (SUB) (2.4000 GHz – 2.4835 GHz) High-pass filter: Modulation method: FHSS 500 Hz – 4 kHz, 12 dB/oct (FRONT), Compatible BLUETOOTH Profiles*2: 50 Hz – 500 Hz, 12 dB/oct (REAR) A2DP (Advanced Audio Distribution Profile) 1.3 Low boost: AVRCP (Audio Video Remote Control Profile) 1.5 0 dB – 10 dB (40 Hz) (SUB) SPP (Serial Port Profile) Power requirements: Corresponding codec: 12 V DC car battery (negative ground (earth)) SBC (.sbc), AAC (.m4a) Power supply voltage: *1 The actual range will vary depending on factors such 10.5 V – 16 V as obstacles between devices, magnetic fields Current drain: around a microwave oven, static electricity, At rated output: 36 A reception sensitivity, antenna (aerial)’s performance, 45 W × 4 (FRONT/REAR at 4 Ω), operating system, software application, etc. 90 W × 2 (SUB at 4 Ω) *2 BLUETOOTH standard profiles indicate the purpose ACC Input: 1 mA of BLUETOOTH communication between devices. Remote input: 1 mA Dimensions: General Approx. 295 mm × 51 mm × 199.5 mm Circuit system: (11 5/8 in × 2 1/8 in × 7 7/8 in) (w/h/d) not incl. Class D Amplifier, projecting parts and controls Pulse power supply Inputs: RCA pin jacks, High level input connector Input level adjustment range (in 6ch mode): 0.3 V – 6 V (RCA pin jacks), 3 V – 12 V (High level input) Outputs: Speaker output connector, WOOFER/SUBWOOFER terminals Speaker impedance: 4 Ω – 8 Ω (Speaker output connector), 2 Ω – 8 Ω (WOOFER/SUBWOOFER terminals)  295 mm (11 5/8 in)  248 mm (9 7/8 in)  184.8 mm (7 3/8 in)  199.5 mm (7 7/8 in)  51 mm (2 1/8 in) 20GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Right XMGS6DSPUC\040CD.fm 010COV.book Page 21 Wednesday, November 1, 2017 4:27 PM Mass: Approx. 2.7 kg (8.5 lb) not incl. accessories Troubleshooting Package contents: Main unit (1) The following checklist will assist in the correction Mounting screws (4) of most problems which you may encounter with High level input cord (1) your unit. Before going through the checklist below, RCA input cord (1) refer to the connection and operating procedures. Speaker output cord (1) The POWER/PROTECTOR indicator does not light Protection cap (1) up. Your dealer may not handle some of the above  The fuse is blown. listed accessories. Please ask the dealer for detailed – Replace the fuse with a new one. information.  The ground (earth) wire is not securely connected. Design and specifications are subject to change – Fasten the ground (earth) wire securely to a without notice. metal point of the car.  The voltage going into the remote input (REM) terminal is too low. Copyrights – Turn on the car audio unit if it is not turned on. – Use a relay if the system employs too many The Bluetooth® word mark and logos are registered amplifiers. trademarks owned by the Bluetooth SIG, Inc. and  Check the battery voltage (10.5 V – 16 V). any use of such marks by Sony Corporation is under license. Other trademarks and trade names are The POWER/PROTECTOR indicator flashes those of their respective owners. quickly.  Turn off the power switch. The speaker outputs iPhone, iPod, and iPod touch are trademarks of have shorted. Apple Inc., registered in the U.S. and other – Rectify the cause of the short. countries.  Turn off the power switch. Make sure the speaker cord and ground (earth) wire are securely Google, Google Play and Android are trademarks of connected. Google LLC. The POWER/PROTECTOR indicator flashes slowly (once every second).  The thermal protector has activated, and the speaker outputs will be decreased. – Make sure the impedance of connected speakers is appropriate. The unit becomes abnormally hot.  The unit heats up abnormally. – Use speakers with suitable impedance: 2 Ω – 8 Ω (stereo), 4 Ω – 8 Ω (when used as a bridging amplifier).  Make sure to place the unit in a well ventilated location. Alternator noise is heard.  The power connecting wires are installed too close to the RCA pin cords. – Keep the wires away from the cords.  The ground (earth) wire is not securely connected. – Fasten the ground (earth) wire securely to a metal point of the car.  Negative speaker wires are touching the car chassis. – Keep the wires away from the car chassis. 21GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Left XMGS6DSPUC\040CD.fm 010COV.book Page 22 Wednesday, November 1, 2017 4:27 PM The sound is muffled. The sound skips during playback of a  Check that the filter settings and the cut-off BLUETOOTH device. frequency adjustment are appropriate according  Reduce the distance between this unit and the to the speaker system. For details, see “Input BLUETOOTH device. connections” (page 10) and ““Speaker  If the BLUETOOTH device is inside a case which connections” (page 14). interrupts the signal, remove the case from the BLUETOOTH device during use. The sound is too quiet.  Several BLUETOOTH devices or other devices  The LEVEL adjustment control is not appropriate. which emit radio waves are in use nearby. Turn the LEVEL adjustment control in the – Turn off the other devices. clockwise direction. – Increase the distance from the other devices.  The playback sound stops momentarily when the connection with the cellular phone is being made BLUETOOTH function on the BLUETOOTH device. This is not a The indicator does not light up. malfunction.  The selected connection mode on the unit is not appropriate. This unit cannot be controlled from the – Check that the SELECT switch is set to the “2V” BLUETOOTH device. or “5V” position.  Check that the connected BLUETOOTH device supports AVRCP. This unit cannot be detected from BLUETOOTH devices. Some functions do not work.  Press PAIRING to set this unit to pairing standby  Check that the connected BLUETOOTH device mode before pairing the BLUETOOTH devices. supports the functions in question.  This unit may not be detected from a BLUETOOTH device already connected to other BLUETOOTH Pairing failed due to a timeout. devices.  Depending on the connecting BLUETOOTH – Operate the BLUETOOTH device to release the device, the time limit for pairing may be short. connections with other BLUETOOTH devices, – Try completing the pairing within the time. then search for this unit.  If the device is already paired, detect this unit Cannot pair. from the BLUETOOTH device while the  If the pairing information of the unit is on the indicator on the unit is flashing quickly. connecting BLUETOOTH device, the unit may not be able to pair with a previously paired Connection is not possible. BLUETOOTH device after initializing the unit. In  The connection is controlled from the this case, delete the pairing information of the BLUETOOTH device. unit from the BLUETOOTH device, and then pair – Operate the BLUETOOTH device to connect to them again. this unit. BLUETOOTH function cannot operate. The device name of this unit does not appear.  Turn off the car audio unit, then turn the car  Depending on the status of the BLUETOOTH audio unit on again. device, it may not be possible to obtain the device name of this unit. Sony | Music Center operation The volume of the connected BLUETOOTH device Application name does not match the actual is low (high). application in “Sony | Music Center”.  Volume level will differ depending on the  Launch the application again from the “Sony | BLUETOOTH device. Music Center” application. – Adjust the volume of the connected BLUETOOTH device or this unit. If these solutions do not help improve the situation, consult your nearest Sony dealer. 22GB XM-GS6DSP 4-733-364-11(1)

D:\Sony\#Work\880191S_XM-GS6DSP(UC)\4733364111\4733364111XMGS6DSPUC\01GB- masterpage: Right XMGS6DSPUC\040CD.fm 010COV.book Page 23 Wednesday, November 1, 2017 4:27 PM Support Site If you have any questions or for the latest support information on this product, please visit the website below: Customers in the United States/Canada: http://esupport.sony.com/ Customers in Asia Pacific/Middle East: http://www.sony-asia.com/section/support http://www.sony-asia.com/caraudio/ 23GB XM-GS6DSP 4-733-364-11(1)


Document Created: 2017-11-06 09:04:15
Document Modified: 2017-11-06 09:04:15
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC