Users Manual

FCC ID: AK8DHURSY63

Users Manual

Download: PDF
FCCID_4370958

          802.11 abgn(ac)+ BT 4.2 combo module


                   Wistron NeWeb Corporation




                                    DHUR-SY63



                                  User Manual




Copyright Statement
 No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any
 form or by any means, whether electronic, mechanical, photocopying, recording or otherwise
 without the prior writing of the publisher.
 Pentium is trademark of Intel.
 All copyright reserved.


Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:


-   Reorient or relocate the receiving antenna.
-   Increase the separation between the equipment and receiver.
-   Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-   Consult the dealer or an experienced radio/TV technician for help.


FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.


This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.


This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.


Country Code selection feature to be disabled for products marketed to the US/CANADA


Operation of this device is restricted to indoor use only



                                              1


Integration instructions for host product manufacturers
Applicable FCC rules to module
FCC Part 15.247 / 15.407
Summarize the specific operational use conditions
The module is must be installed in mobile device.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna
3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band
     by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user
regarding
      to Regulatory Domain change.
As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer considered
valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization. The OEM integrator has to be aware not to provide information to the end user regarding how
to install or remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.

Limited module procedures
Not applicable

Trace antenna designs
Not applicable

RF exposure considerations
20 cm separation distance and co-located issue shall be met as mentioned in “Summarize the specific
operational use conditions”.
Product manufacturer shall provide below text in end-product manual
“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.”




                                                      2


Antennas
 Model     Antenna                          Antenna gain (dBi)                         Antenna       Remark
 name      type          2400 ~   5150 ~  5250 ~  5470 ~  5725 ~                       connector
                       2483.5MHz 5250MHz 5350MHz 5725MHz 5850MHz
 Wi-Fi     Printed     1.58          2.43         3.4         4.35         4.26        N/A           For Wi
 ANT-0                                                                                               Fi
 Wi-Fi     Printed     1.55          2.58         2.55        2.51         2.65        N/A           For Wi
 ANT-1                                                                                               Fi
 NA        Printed     -3.59         --           --          --           --          N/A           For BT
Label and Compliance Information
Product manufacturers need to provide a physical or e-label stating
“Contains FCC ID: AK8DHURSY63” with finished product
Information on Test Modes and Additional Testing Requirements
Test tool: MT7663 QA, v0.0.2.6 shall be used to set the module to transmit continuously.
Additional Testing, Part 15 Subpart B Disclaimer
The module is only FCC authorized for the specific rule parts listed on the grant, and that the host product
manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the
modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance
testing with the modular transmitter installed




                                                         3


                              Industry Canada statement:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:

(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause
undesired operation of the device

Cet appareil contient des émetteurs / récepteurs exempts de licence qui sont conformes
au (x) RSS (s) exemptés de licence d'Innovation, Sciences et Développement
économique Canada. L'opération est soumise aux deux conditions suivantes:

(1) Cet appareil ne doit pas causer d'interférences
(2) Cet appareil doit accepter toute interférence, y compris les interférences pouvant
provoquer un fonctionnement indésirable de l'appareil

This radio transmitter (IC: 409B-DHURSY63) has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 409B-DHURSY63) a été approuvé par Industrie Canada
pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est
supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur.


Antenna information
Model   Antenna                      Antenna gain (dBi)                   Antenna     Remark
name    type        2400 ~     5150 ~      5250 ~      5470 ~    5725 ~   connector
                  2483.5MHz   5250MHz     5350MHz     5725MHz   5850MHz
Wi-Fi   Printed   1.58        2.43        3.4         4.35      4.26      N/A         For Wi
ANT-0                                                                                 Fi
Wi-Fi   Printed   1.55        2.58        2.55        2.51      2.65      N/A         For Wi
ANT-1                                                                                 Fi
NA      Printed   -3.59       --          --          --        --        N/A         For BT



                                                 4


Caution:
(i) the device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;


(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the
equipment still complies with the e.i.r.p. limit;


(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the band 5725-5850 MHz shall be such that the equipment still complies with
the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as
appropriate; and

Operations in the 5.25-5.35GHz band are restricted to indoor usage only.


Avertissement:
(i) les dispositifs fonctionnant dans la bande de 5150 à 5250MHz sont réservés
uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;


(ii) pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis
pour les dispositifs utilisant les bandes de 5250 à 5350MHz et de 5470 à 5725 MHz doit
être conforme à la limite de la p.i.r.e;


(iii) pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis
(pour les dispositifs utilisant la bande de 5725 à 5850 MHz) doit être conforme à la limite
de la p.i.r.e. spécifiée pour l'exploitation point à point et l'exploitation non point à point,
selon le cas;


Les opérations dans la bande de 5.25-5.35GHz sont limités à un usage intérieur
seulement.

Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.


Déclaration d'exposition aux radiations:


                                               5


Cet équipement est conforme Canada limites d'exposition aux radiations dans un
environnement non contrôlé. Cet équipement doit être installé et utilisé à distance
minimum de 20cm entre le radiateur et votre corps.



This device is intended only for OEM integrators under the following conditions:



1) The transmitter module may not be co-located with any other transmitter or antenna.


As long as 1 condition above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.



Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes:



1) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.


Tant que les 1 condition ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.

IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada authorization is
no longer considered valid and the IC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate Canada authorization.

NOTE IMPORTANTE:

Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut

                                            6


pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé
de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation
distincte au Canada.

End Product Labeling

The final end product must be labeled in a visible area with the following: “Contains IC:
409B-DHURSY63”.

Plaque signalétique du produit final

Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:
"Contient des IC: 409B-DHURSY63".



Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.



Manuel d'information à l'utilisateur final

L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur
final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de
l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises
et avertissements comme indiqué dans ce manuel.




                                              7


Europe – EU Declaration of Conformity


This device complies with the essential requirements of the Radio Equipment directive: 2014 / 53 / EU.
The following test methods have been applied in order to prove presumption of conformity with the
essential requirements of the Radio Equipment directive: 2014 / 53 / EU:


EN 300 328 V2.1.1
EN 301 893 V2.1.1
EN 300 440 V2.1.1
Draft EN 301 489-1 V2.2.0
EN 301 489-3 V2.1.1
Draft EN 301 489-17 V3.2.0
EN 62311:2008
EN 50665:2017
EN 50385:2002
IEC 62368-1:2014; and/or
EN 62368-1:2014+A11:2017


19.54 dBm, 2412-2472MHz (Wi Fi)
4.51 dBm, 2402-2480MHz (BT EDR)
0.26 dBm, 2402-2480MHz (BT LE)
21.41 dBm, 5150-5250MHz
21.29 dBm, 5250-5350MHz
22.67 dBm, 5470-5725MHz
13.95 dBm, 5745-5825MHz
SW version: 1.0


The minimum distance between the user and/or any bystander and the radiating structure of the
transmitter is 20cm.




5150 ~ 5350 MHz is limited to indoor used in below countries.




                                                    8


                34 AZZAAMIXX®SOEECOOD BRRKREEMETEF | YTSE
 1iRMK9Z T MCMEAAAMAEHRF 1 30N
                        — id7iPEKNeAoitraltteeSo
                        — #—ZHMENINENEHNEHENET — &
eSE yCCESNRERREHETY —SemuirirosA)XAMYEVBNE — SEEYCEdE
                    — NNERHELHE—M—HfESEXIT— HMSHHLIH &
$ue—Bintin : EYENYAAAEVo~yBHfNeTS<—HM —|—§
                      — oXE—HXYEeqmesifyl| — sHfesh
EBy+bBRreNN! . e . oliRHE — MEAINZYEEEYAR—H— 4|€
                                           2g uemieL
                                       XXXXXX—LOZ 1 (é£@#xX@
                                        E9as—4NnHd: #P#p$ME
                                 ° £2094fI£3ME—)1AP4M4
                              exXMoOoREAMEEURoRERCE
                                                    UH|   MN|   HD
                                            35| 14 | x1 | XS| IS
                                            O¥ | Ld 14 | ON| TN
                                            iw|ne| m ) a1) n
                                            mlaga‘si|G) u
                                            31 | si 30| #3) 33
                                            v_D.N0,0m.m_m.._.4


Table of Contents

1. INTRODUCTION

2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION

3. CONNECTING TO AN EXISTING NETWORK

4. MODIFYING A WIRELESS NETWORK

4.1 MODIFYING GENERAL SETTINGS ................................................................................................
4.2 MODIFYING SECURITY SETTINGS ................................................................................................


5. Product Specifications




                                                               10


1. INTRODUCTION

DHUR-SY63 is a 802.11 a/b/g/n /ac and Bluetooth Combo module that provides the easiest way
to wireless networking. This User Manual contains detailed instructions in the operation of this
product. Please keep this manual for future reference.


System Requirements
        - 128 MB of RAM or later (recommended)
        - 300 MHz processor or higher



2. Driver/Utility Installation
The driver should have been installed before the TV is shipped from the manufacturer. You can
start using its network function without installing driver or utility.



3. Connecting to an Existing Network
1. Use the remote control that came with your TV to access the network configuration settings
   page.


2. Select the scanning wireless network function. The system starts to scan for available network.
   On this list, click Refresh to refresh the list at any time


3. Select the network you want to connect to.


4. If the chosen network has security enabled, you will have to setup corresponding security
   parameter. Contact the network manager for the correct settings. Select the security type and
   fill in required parameters. The options include the following:

      WPA/WPA2/CCKM
      WPA/WPA2 Passphrase
      802.1x
      Pre-Shared Key (Static WEP)
      None




                                                11


4. Modifying a Wireless Network
4.1 Modifying General Settings
1. Use the remote control that came with your TV to access the network configuration settings
   page.
2. From the profile list, select one profile and choose the modify function.
3. Modify the settings below for your network.
               Profile Name     Identifies the configuration wireless network profile.
                                This name must be unique. Profile names are not
                                case sensitive.

               Client Name      Identifies the client machine.

         Use this profile for   Configures station to operate in Access Point mode.
        Access Point mode

            Network Names       The IEEE 802.11 wireless network name. This field
                   (SSIDs)      has a maximum limit of 32 characters. Configure up
                                to three SSIDs (SSID1, SSID2, and SSID3).




                                                12


4.2 Modifying Security Settings

1. Use the remote control that came with your TV to access the network configuration settings
   page.
2. Select a security option of this wireless network. This product provides security options below.
   Contact your wireless network administrator for choosing a correct option.

      WPA/WPA2/CCKM
      WPA/WPA2 Passphrase
      802.1x
      Pre-Shared Key (Static WEP)
      None

   WPA/WPA2               Enables the use of Wi-Fi Protected Access (WPA).
                          Choosing WPA/WPA2 opens the WPA/WPA2 EAP drop-down menu.
                          The options include:
                           EAP-FAST
                           EAP-TLS
                           EAP-TTLS
                           EAP-SIM
                           PEAP (EAP-GTC)
                           PEAP (EAP-MSCHAP V2)
                           LEAP
   WPA/WPA2               Enables WPA/WPA2 Passphrase security.
   Passphrase             Click on the Configure button and fill in the WPA/WPA2 Passphrase.

   802.1x                 Enables 802.1x security. This option requires IT administration.
                          Choosing 802.1x opens the 802.1x EAP type drop-down menu. The
                          options include:

                             EAP-FAST
                             EAP-TLS
                             EAP-TTLS
                             EAP-SIM
                             PEAP (EAP-GTC)
                             PEAP (EAP-MSCHAP V2)
                             LEAP

   Pre-Shared Key         Enables the use of pre-shared keys that are defined on both the access
   (Static WEP)           point and the station.
                          To define pre-shared encryption keys, choose the Pre-Shared Key radio
                          button and click the Configure button to fill in the Define Pre-Shared
                          Keys window.



                                                13


None                   No security (not recommended).

Allow Association to   Check this check box if the access point with which the client adapter is
Mixed Cells            to associate has WEP set to Optional and WEP is enabled on the client
                       adapter. Otherwise, the client is unable to establish a connection with
                       the access point.
Limit Time for         Check this check box and enter the number of seconds (up to 300) after
Finding Domain         which the authentication process times out when trying to find the
Controller To
                       domain controller. Entering zero is like unchecking this check box,
                       which means no time limit is imposed for finding the domain controller.
                       Note: The authentication process times out whenever the authentication
                       timer times out or the time for finding the domain controller is reached.

Group Policy Delay     Specify how much time elapses before the Windows logon process
                       starts group policy. Group policy is a Windows feature used by
                       administrators to specify configuration options for groups of users. The
                       objective is to delay the start of Group Policy until wireless network
                       authentication occurs. Valid ranges are from 0 to 65535 seconds. The
                       value that you set goes into effect after you reboot your computer with
                       this profile set as the active profile.
                       This drop-down menu is active only if you chose EAP-based
                       authentication.




                                             14


  5. Product            Specifications

  Product Name:WLAN/BT Module
  Brand Name:Wistron NeWeb Corporation
  Model Name:DHUR-SY63


     Item                                      Content
                 BT: 2402~2480MHz
                 WLAN:
Frequency           2412~2462MHz
range               5.15~5.25GHz
                    5.47~5.725GHz
                    5.725~5.850GHz
                 BT/BLE: 1MHz/2MHz
Channel          WLAN:
spacing          5MHz for 2.4G
                 20MHz for 5.0G
                 BT: GFSK, π/4 – DQPSK, 8DPSK
Modulation
                  WLAN : DSSS : CCK,DQPSK,DBPSK
technology
                      OFDM :BPSK,QPSK,16QAM,64QAM,256QAM
                 BT: 1/2/3Mbps, BLE: 1Mbps
                 802.11b: 11/5.5/2/1Mbps
                 802.11g: 54/48/36/24/18/12/9/6Mbps
                 802.11a: 54/48/36/24/18/12/9/6Mbps
                 802.11n:
Data Rate        20MHz: MCS0~MCS7
                 40MHz: MCS0~MCS7
                 802.11ac
                 VHT20: MCS0~MCS8
                 VHT40: MCS0~MCS9
                 VHT80: MCS0~MCS9
Host interface   USB 2.0
Operation
                 3.3V
voltage
Operation
                 -10o ~ 60oC
temperature
Antenna Type     PCB printed antenna

                                          15


Antenna gain




Antenna peak      WiFi Antenna : 1.58dBi for 2.4Ghz , 4.35dBi for 5GHz
gain              BT Antenna : -3.59dBi




                                       16



Document Created: 2019-07-23 10:28:44
Document Modified: 2019-07-23 10:28:44

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC