User manual

FCC ID: AK8145890811

Users Manual

Download: PDF
FCCID_3800135

Installation Manual Information of FCC ID Label of this device: FCC ID: AK8145890811 For OEM integration only – device cannot be sold to general public. Therefore we will ask OEM to include the following statements required by FCC on the product and in the Installation manual Notice. Contents 1.Land Pattern (Recommended) 2.Supply Voltage 3.Antenna 4.Notice **This module can only be installed in host powered by battery.

1.Land Pattern TOP View (Recommended) 3.95 3.65 3.15 2.825 2.575 2.375 2.125 1.925 1.675 1.475 1.225 1.025 0.775 0.575 0.325 0.125 Please take a solid ground this shaded area. In the surface layer, in the inner layer, 3.85 3.55 there is no problem either. 3.05 2.50 1.30 0.10 0.60 0.35 0.55 0.80 1.00 1.25 1.45 1.70 1.90 2.15 2.35 2.60 2.80 3.05 3.25 3.50 3.85 0.60 1.30 2.50 Unit : mm 3.15 3.65 3.95

2.Supply Voltage min. typ. max. unit Operating Temperature -20 +25 +85 deg.C Supply VBAT 3.13 3.2 4.4 V Voltage VDDXO* 1.70 1.8 1.9 V VIO * 1.71 1.8 or 3.3 3.63 V *VDDXO and VIO don’t influence the RF characteristic. This module can only be installed in host powered by battery.

3.Antenna ■Please perform the antenna design that followed the specifications of the antenna. ■About the signal line between an antenna and a module It is a 50-ohm line design. Fine tuning of return loss etc. can be performed using a matching network. However, it is required to check "Class1 change" and "Class2 change" which the authorities define then. The concrete contents of a check are the following three points. １）It is the same type as the antenna type of antenna specifications. ２）An antenna gain is lower than a gain given in antenna specifications. ３）The emission level is not getting worse.

Antenna gain WLAN Main/Buetoot Frequency [Vie] 2402 —are0 2o2 Emm zis beak Gain) 40 «s as #o prarowie

RF signal line stricture and characteristics Micro Strip Line GapXK Signal GapX Widthfum] 279 183 279 Thicness{um] Material & tand 22 [CH Cu 35 Prepreg 3.5 0.012 20 L2 35 Prepreg 3.5 0.012 20 Bsou AL1DR(HVIM) L1:Signal L3:GND roas Characteristic Impedance : 500 Strip Line a CapX Signal Cap% Insertion Loss(L1+L3) : 0.5dB Width{um] 110 73 110 Thicness{um] Material & tand 2CCou 35 Prepreg 3.5 0.012 20 L2 35 prepreg 35 0012 2035 B7 Cu Prepreg 3.5 0.012 20 L4 35 Prepreg 3.5 0.012 es ComCC(CGeu L1:GND L3:Signal L5:GND »Gap from signal line to side gnd

3.Antenna(Trace design)

3.Antenna(Trace design)

4. Notice Please describe the following warning on the final product which contains this module. Contains Transmitter Module FCC ID:AK8145890811 or Contains FCC ID: AK8145890811 This device complies with Part 15 of FCC Rules and Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme à la partie 15 des règles de la FCC et aux normes des CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. ※When the product is small, as for these words mentioned above, the posting to a manual is possible. ●Please describe the following warning to the manual. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

4. Notice ®@Please describe the following statement to the manual. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help.

4. Notice ●When installing it in a mobile equipment. Please describe the following warning to the manual. If mobile equipment use only low power BT/BLE or low power Wi-Fi. This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). When installing this module in host with multiple or additional transmitters, additional RF exposure evaluation is required. Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d'exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale autorisée (MPE). Lors de l'installation de ce module sur un hôte avec plusieurs émetteurs ou plus, une évaluation d'exposition RF supplémentaire est requise. In the case of conditions other than the above This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body. When installing this module in host with multiple or additional transmitters, additional RF exposure evaluation is required. Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d'exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. Lors de l'installation de ce module sur un hôte avec plusieurs émetteurs ou plus, une évaluation d'exposition RF supplémentaire est requise. Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm.

4. Notice


Document Created: 2019-04-04 20:23:34
Document Modified: 2019-04-04 20:23:34
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC