Test Report_BLE

FCC ID: ACQ-MG3

Test Report

Download: PDF
FCCID_4432016

FCC Test Report FCC ID : ACQ-MG3R Equipment : Set Top Box Model No. : MG3-R Brand Name : TiVo Applicant : ARRIS Address : 101 Tournament Drive, Horsham Pennsylvania, United States, 19044 Standard : 47 CFR FCC Part 15.247 Received Date : Mar. 20, 2019 Tested Date : May 21 ~ May 28, 2019 We, International Certification Corp., would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It may be duplicated completely for legal use with the approval of the applicant. It shall not be reproduced except in full without the written approval of our laboratory. Reviewed by: Approved by: Along Chen / Assistant Manager Gary Chang / Manager Report No.: FR932003AE Page : 1 of 34 Report Version: Rev. 01

Table of Contents 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information.............................................................................................................................................. 5 1.2 Local Support Equipment List ................................................................................................................ 7 1.3 Test Setup Chart .................................................................................................................................... 7 1.4 Test Equipment List and Calibration Data .............................................................................................. 8 1.5 Test Standards ....................................................................................................................................... 9 1.6 Deviation from Test Standard and Measurement Procedure ................................................................. 9 1.7 Measurement Uncertainty ...................................................................................................................... 9 2 TEST CONFIGURATION .....................................................................................................................10 2.1 Testing Condition .................................................................................................................................10 2.2 The Worst Test Modes and Channel Details .......................................................................................10 3 TRANSMITTER TEST RESULTS........................................................................................................11 3.1 Conducted Emissions ...........................................................................................................................11 3.2 6dB and Occupied Bandwidth ..............................................................................................................14 3.3 RF Output Power ..................................................................................................................................17 3.4 Power Spectral Density ........................................................................................................................19 3.5 Emissions in Restricted Frequency Bands ...........................................................................................22 3.6 Emissions in non-restricted Frequency Bands .....................................................................................32 4 TEST LABORATORY INFORMATION ...............................................................................................34 Report No.: FR932003AE Page : 2 of 34 Report Version: Rev. 01

Release Record Report No. Version Description Issued Date FR932003AE Rev. 01 Initial issue Jun. 10, 2019 Report No.: FR932003AE Page : 3 of 34 Report Version: Rev. 01

Summary of Test Results FCC Rules Test Items Measured Result [dBuV]: 0.162MHz 15.207 AC Power Line Conducted Emissions Pass 47.96 (Margin -7.38dB) - AV 15.247(d) [dBuV/m at 3m]: 42.55MHz Radiated Emissions Pass 15.209 36.31 (Margin -3.69dB) - PK 15.247(b)(3) Maximum Output Power Power [dBm]: 1.47 Pass 15.247(a)(2) 6dB Bandwidth Meet the requirement of limit Pass 15.247(e) Power Spectral Density Meet the requirement of limit Pass 15.203 Antenna Requirement Meet the requirement of limit Pass Declaration of Conformity: The test results with all measurement uncertainty excluded are presented in accordance with the regulation limits or requirements declared by manufacturers. Comments and Explanations: The declared of product specification for EUT presented in the report are provided by the manufacturer, and the manufacturer takes all the responsibilities for the accuracy of product specification. Report No.: FR932003AE Page : 4 of 34 Report Version: Rev. 01

1 General Description 1.1 Information 1.1.1 Specification of the Equipment under Test (EUT) RF General Information Frequency Range Bluetooth Ch. Freq. (MHz) Channel Number Data Rate (MHz) Mode 2400-2483.5 V4.2 LE 2402-2480 0-39 [40] 1 Mbps Note 1: Bluetooth LE (Low energy) uses GFSK modulation. 1.1.2 Antenna Details Ant. No. Type Connector Gain (dBi) Remarks 1 Printing N/A 3.6 --- 1.1.3 Power Supply Type of Equipment under Test (EUT) Power Supply Type 12Vdc from adapter 1.1.4 Accessories Accessories No. Equipment Description Brand: TiVo Manufacturer: LITE-ON INC Model: PB-1300-3AR5 1 Adapter Power Rating: I/P: 100-120Vac, 1.0A, 60Hz O/P: 12Vdc, 2.5A Power Line: 1.8m non-shielded without core Brand: TiVo Manufacturer: NETBIT ELECTRONICS LTD. Model: NBS36E120250VU 2 Adapter Power Rating: I/P: 100-120Vac, 60Hz, 0.8A O/P: 12.0Vdc, 2.5A Power Line: 1.8m non-shielded without core 3 HDMI cable 1.8m shielded without core Brand: SEAGATE 4 HDD Model: ST2000VT000 Product: Video 2.5 HDD Brand: REMOTESOLUTION CO.,LTD 5 Remote Control Model: SBOM_03031_000 AA Battery for Remote 6 1.5Vdc *2 Control Report No.: FR932003AE Page : 5 of 34 Report Version: Rev. 01

1.1.5 Channel List Frequency band (MHz) 2400~2483.5 Frequency Frequency Frequency Frequency Channel Channel Channel Channel (MHz) (MHz) (MHz) (MHz) 37 2402 9 2422 18 2442 28 2462 0 2404 10 2424 19 2444 29 2464 1 2406 38 2426 20 2446 30 2466 2 2408 11 2428 21 2448 31 2468 3 2410 12 2430 22 2450 32 2470 4 2412 13 2432 23 2452 33 2472 5 2414 14 2434 24 2454 34 2474 6 2416 15 2436 25 2456 35 2476 7 2418 16 2438 26 2458 36 2478 8 2420 17 2440 27 2460 39 2480 1.1.6 Test Tool and Duty Cycle Test Tool Putty, V0.6 Duty Cycle (%) Duty Factor (dB) Duty Cycle and Duty Factor 64.52 1.90 1.1.7 Power Index of Test Tool Test Frequency (MHz) Modulation Mode 2402 2440 2480 GFSK/1Mbps Default Default Default Report No.: FR932003AE Page : 6 of 34 Report Version: Rev. 01

1.2 Local Support Equipment List Support Equipment List No. Equipment Brand Model FCC ID Remarks 1 Notebook DELL Latitude E6440 DoC --- 2 TV CHIMEI TL-24LF500D --- --- 3 USB Flash Kingston DTSE9 --- --- 4 USB Flash Kingston DTSE9 --- --- 1.3 Test Setup Chart Test Setup Diagram No. Signal cable / Length (m) 1 HDMI, 1.8m shielded. 2 Fiber, 1.2m non-shielded. 3 RJ45, 10m non-shielded. Report No.: FR932003AE Page : 7 of 34 Report Version: Rev. 01

1.4 Test Equipment List and Calibration Data Test Item Conducted Emission Test Site Conduction room 1 / (CO01-WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until Receiver R&S ESR3 101657 Jan. 08, 2019 Jan. 07, 2020 LISN SCHWARZBECK Schwarzbeck 8127 8127-667 Nov. 05, 2018 Nov. 04, 2019 LISN SCHWARZBECK Schwarzbeck 8127 8127-666 Nov. 29, 2018 Nov. 28, 2019 (Support Unit) RF Cable-CON Woken CFD200-NL CFD200-NL-001 Oct. 23, 2018 Oct. 23, 2019 50 ohm terminal NA 50 02 Apr. 19, 2019 Apr. 18, 2020 (Support Unit) Measurement AUDIX e3 6.120210k NA NA Software Note: Calibration Interval of instruments listed above is one year. Test Item Radiated Emission Test Site 966 chamber 3 / (03CH03-WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until Spectrum Analyzer R&S FSV40 101499 Jan. 07, 2019 Jan. 06, 2020 Receiver R&S ESR3 101658 Dec. 11, 2018 Dec. 10, 2019 Bilog Antenna SCHWARZBECK VULB9168 VULB9168-685 Apr. 17, 2019 Apr. 16, 2020 Horn Antenna SCHWARZBECK BBHA 9120 D BBHA 9120 D 1206 Jan. 07, 2019 Jan. 06, 2020 1G-18G Horn Antenna SCHWARZBECK BBHA 9170 BBHA 9170517 Nov. 15, 2018 Nov. 14, 2019 18G-40G Loop Antenna R&S HFH2-Z2 100330 Nov. 09, 2018 Nov. 08, 2019 Loop Antenna Cable KOAX KABEL 101354-BW 101354-BW Oct. 08, 2018 Oct. 07, 2019 Preamplifier EMC EMC02325 980187 Aug. 24, 2018 Aug. 23, 2019 Preamplifier Agilent 83017A MY53270014 Aug. 09, 2018 Aug. 08, 2019 Preamplifier EMC EMC184045B 980192 Aug. 09, 2018 Aug. 08, 2019 RF cable-3M HUBER+SUHNER SUCOFLEX104 MY22620/4 Oct. 01, 2018 Sep. 30, 2019 EMC104-SM-SM-80 RF cable-8M EMC 181107 Oct. 01, 2018 Sep. 30, 2019 00 RF cable-1M HUBER+SUHNER SUCOFLEX104 MY22624/4 Oct. 01, 2018 Sep. 30, 2019 EMC8D-NM-NM-800 LF cable-0.8M EMC EMC8D-NM-NM-800 Oct. 01, 2018 Sep. 30, 2019 -001 EMC8D-NM-NM-300 LF cable-3M EMC 131103 Oct. 01, 2018 Sep. 30, 2019 0 EMC8D-NM-NM-130 LF cable-13M EMC 131104 Oct. 01, 2018 Sep. 30, 2019 00 Measurement SENSE-15247_DTS V5.10.1 -- NA NA Software Note: Calibration Interval of instruments listed above is one year. Report No.: FR932003AE Page : 8 of 34 Report Version: Rev. 01

@ Infernational Certification Corp. Test Item RF Conducted Test Site (THO1—WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until Spectrum Analyzer R&S FSV40 101063 Apr. 17, 2019 Apr. 16, 2020 Power Meter Anritsu ML2495A 1241002 Oct. 09, 2018 Oct. 08, 2019 Power Sensor Anritsu MA2Z411B 1207366 Oct. 09, 2018 Oct. 08, 2019 AC POWER SOURCE APC AFC—5O0W E312060012 Nov. 29, 2018 Nov. 28, 2019 Measurement Software Sporton Sporton_1 1.3.30 NA NA Note: Calibration Interval of instruments listed aboveis one year. 1.5 Test Standards According to the specification of EUT, the EUT must comply with following standards and KDB documents. 47 CFR FCC Part 15.247 ANSI C63.10—2013 FCC KDB 558074 DO1 15.247 Meas Guidance v05r02 1.6 Deviation from Test Standard and Measurement Procedure None 1.7 Measurement Uncertainty I1SO/IEC 17025 requires that an estimate of the measurement uncertainties associated with the emissions test results be included in the report. The measurement uncertainties given below are based on a 95% confidence level (based on a coverage factor (k=2) Measurement Uncertainty Parameters Uncertainty Bandwidth +34.130 Hz Conducted power +0.808 dB Power density +0.583 dB Conducted emission +2.715 dB AC conducted emission +2.92 dB Radiated emission < 1GHz +3.96 dB Radiated emission > 1GHz +4.51 dB Report No.: FR932003AE Page : 9 of 34 Report Version: Rev. 01

C Infernational Certification Corp. 2 Test Configuration 2.1 Testing Condition Test Item Test Site Ambient Condition Tested By AC Conduction COO1—WwS 24°C / 65% Alex Tsai . has _ o Roger Lu Radiated Emissions O3CHO3—WS 23°C / 68% Akun Chung RF Conducted THO1—WS 22°C / 66% Aska Huang » FCC Designation No.: TWO009 » FCC site registration No.: 207696 > ISED#: 10807A > CAB identifier: TW2732 2.2 The Worst Test Modes and Channel Details . Test Frequency Test Test item Mode (MHz) Data Rate Configuration AC Power Line Conducted Emissions BTLE 2402 1Mb Radiated Emissions S 1GHz PS Maximum Output Power 60B bandwidth _ BTLE 2402, 2440, 2480 1Mbps Power spectral density Radiated Emissions > 1GHz NOTE: Two adapters (LITE—ON & NETBIT) had been covered during the pretest and found that NETBIT adapter was the worst case for radiated emission test and LITE—ON adapter was the worst case for conducted emission test. Report No.: FR932003AE Page : 10 of 34 Report Version: Rev. 01

3 Transmitter Test Results 3.1 Conducted Emissions 3.1.1 Limit of Conducted Emissions Conducted Emissions Limit Frequency Emission (MHz) Quasi-Peak Average 0.15-0.5 66 - 56 * 56 - 46 * 0.5-5 56 46 5-30 60 50 Note 1: * Decreases with the logarithm of the frequency. 3.1.2 Test Procedures 1. The device is placed on a test table, raised 80 cm above the reference ground plane. The vertical conducting plane is located 40 cm to the rear of the device. 2. The device is connected to line impedance stabilization network (LISN) and other accessories are connected to other LISN. Measured levels of AC power line conducted emission are across the 50 Ω LISN port. 3. AC conducted emission measurements is made over frequency range from 150 kHz to 30 MHz. 4. This measurement was performed with AC 120V/60Hz 3.1.3 Test Setup Report No.: FR932003AE Page : 11 of 34 Report Version: Rev. 01

3.1.4 Test Result of Conducted Emissions Modulation Mode GFSK Test Freq. (MHz) 2402 Power Phase Line Note 1: Level (dBuV) = Read Level (dBuV) + LISN Factor (dB) + Cable Loss (dB). 2: Over Limit (dB) = Level (dBuV) – Limit Line (dBuV). Report No.: FR932003AE Page : 12 of 34 Report Version: Rev. 01

Modulation Mode GFSK Test Freq. (MHz) 2402 Power Phase Neutral Note 1: Level (dBuV) = Read Level (dBuV) + LISN Factor (dB) + Cable Loss (dB). 2: Over Limit (dB) = Level (dBuV) – Limit Line (dBuV). Report No.: FR932003AE Page : 13 of 34 Report Version: Rev. 01

3.2 6dB and Occupied Bandwidth 3.2.1 Limit of 6dB Bandwidth The minimum 6dB bandwidth shall be at least 500 kHz. 3.2.2 Test Procedures 6dB Bandwidth 1. Set c resolution bandwidth (RBW) = 100 kHz, Video bandwidth = 300 kHz. 2. Detector = Peak, Trace mode = max hold. 3. Sweep = auto couple, Allow the trace to stabilize. 4. Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower) that are attenuated by 6dB relative to the maximum level measured in the fundamental emission. Occupied Bandwidth 1. Set resolution bandwidth (RBW) = 1% ~ 5 % of OBW, Video bandwidth = 3 x RBW 2. Detector = Sample, Trace mode = max hold. 3 Sweep = auto couple, Allow the trace to stabilize. 4. Use the OBW measurement function of spectrum analyzer to measure the occupied bandwidth. 3.2.3 Test Setup Report No.: FR932003AE Page : 14 of 34 Report Version: Rev. 01

3.2.4 Test Result of 6dB and Occupied Bandwidth Summary Mode Max-N dB Max-OBW ITU-Code Min-N dB Min-OBW (Hz) (Hz) (Hz) (Hz) 2.4-2.4835GHz - - - - - BT-LE(1Mbps) 746.377k 1.118M 1M12F1D 742.754k 1.096M Max-N dB = Maximum 6dB down bandwidth; Max-OBW = Maximum 99% occupied bandwidth; Min-N dB = Minimum 6dB down bandwidth; Min-OBW = Minimum 99% occupied bandwidth; Result Mode Result Limit Port 1-N dB Port 1-OBW (Hz) (Hz) (Hz) BT-LE(1Mbps) - - - - 2402MHz Pass 500k 746.377k 1.103M 2440MHz Pass 500k 742.754k 1.096M 2480MHz Pass 500k 742.754k 1.118M Port X-N dB = Port X 6dB down bandwidth; Port X-OBW = Port X 99% occupied bandwidth; Report No.: FR932003AE Page : 15 of 34 Report Version: Rev. 01

Infernational Certification Corp. BT—LE(1LMbps) EBW 2402MHz ce 57 c T 7 24020b o— 2agrcite 40— i 5 — 5, . [ | * 2sve 5 "D asuce 45 oo( i |ich ao~ ano rew rew 10e 257 owz 25 vew o~ vew a 30e PA 1o0ktic as! Sueep Time Sneep Time | a~ a0— i Ime 10tme i Detector Type 45— Detector Type 454 I Pesk an~ semple s i [ Sm : i « mm l ~| s3 & i c baua Pors[A/ 20055 aanse zane 2atese 2aosesq 200755 raoss zes 2aone 2ans2se GdB(He) FeSdB(H Fr—6dB(He) OBWI) FLOBWH) Fh—OBWIHe) im. Port meam ransees ravuie raom 2aounre 2aoisine Siok 1 BT—LE(1Mbps) EBW 2440MHz ce 5 c zon o— rasore Span us Span 250 do— 2svie row row 100z 45 owz vw n vaw 3oitte P tookic Sweep Time a~ Sweep Time Ims 101ms Detector Type 357 Detector Type Pesk ao~ somple ( 5| dfi : 1 « mb | s3 : i 1 masa Pors [A 2eess aaase 2i 2uss 2ait2sd 2esamse aasass mc 2itse 2an256 GdBite) FsdBiein Fre6dB(Hq OBWIi F—OBWi): Fh—OBW(He) LimitHe) Port marsik ragsseie pmaine Leem 2adoines 2igo2se Si0k 1 BT—LE(1Mbps) EBW 2480MHz ce 0 c 248GHe s— 2a8gH 5 pon ao— 5, pmn 20e 2svure rew as~ rew Tonkir an~ owir vew vew us 20e 1004c Sueep Time o Sneep Time Ims us 10tme Detector Type Detsctor Type Pesk «10— Somple [ Sm : 1 1 mc l ~| s3 : 1 : basa Pors[A/ zuse awhse zks umss BSRd zarise ambse ziss masbse BSed 6dBHe) FedBiHc Fr—6dB(He) OBWIHe) FL—OBW(He) Fh—OBW(He) LimitHe Port marsik pasoie ramasie roiem 2arouise 2ammsise Siok

3.3 RF Output Power 3.3.1 Limit of RF Output Power Conducted power shall not exceed 1Watt. Antenna gain <= 6dBi, no any corresponding reduction is in output power limit. 3.3.2 Test Procedures A broadband RF power meter is used for output power measurement. The video bandwidth of power meter is greater than DTS bandwidth of EUT. If duty cycle of test signal is not 100 %, trigger and gating function of power meter will be enabled to capture transmission burst for measuring output power. 3.3.3 Test Setup Report No.: FR932003AE Page : 17 of 34 Report Version: Rev. 01

3.3.4 Test Result of Maximum Output Power Summary of Peak Conducted Output Power Mode Power Power (dBm) (W) 2.4-2.4835GHz - - BT-LE(1Mbps) 1.47 0.00140 Result Mode Result Gain Power Power Limit (dBi) (dBm) (dBm) BT-LE(1Mbps) - - - - 2402MHz Pass 3.60 1.47 30.00 2440MHz Pass 3.60 0.84 30.00 2480MHz Pass 3.60 -0.11 30.00 Summary of Conducted (Average) Output Power Mode Power Power (dBm) (W) 2.4-2.4835GHz - - BT-LE(1Mbps) 1.33 0.00136 Result Mode Result Gain Power Power Limit (dBi) (dBm) (dBm) BT-LE(1Mbps) - - - - 2402MHz Pass 3.60 1.33 - 2440MHz Pass 3.60 0.69 - 2480MHz Pass 3.60 -0.31 - Note: Average power is for reference only. Report No.: FR932003AE Page : 18 of 34 Report Version: Rev. 01

3.4 Power Spectral Density 3.4.1 Limit of Power Spectral Density Power spectral density shall not be greater than 8 dBm in any 3 kHz band. 3.4.2 Test Procedures 1. Set the RBW = 3 kHz, VBW = 10 kHz. 2. Detector = Peak, Sweep time = auto couple. 3. Trace mode = max hold, allow trace to fully stabilize. 4. Use the peak marker function to determine the maximum amplitude level. 3.4.3 Test Setup Report No.: FR932003AE Page : 19 of 34 Report Version: Rev. 01

3.4.4 Test Result of Power Spectral Density Summary Mode PD (dBm/RBW) 2.4-2.4835GHz - BT-LE(1Mbps) -12.78 Result Mode Result Gain PD PD Limit (dBi) (dBm/RBW) (dBm/RBW) BT-LE(1Mbps) - - - - 2402MHz Pass 3.60 -12.78 8.00 2440MHz Pass 3.60 -13.58 8.00 2480MHz Pass 3.60 -14.53 8.00 Report No.: FR932003AE Page : 20 of 34 Report Version: Rev. 01

Report No.: FR932003AE Page : 21 of 34 Report Version: Rev. 01

C Infernational Certification Corp. 3.5 Emissions in Restricted Frequency Bands 3.5.1 Limit of Emissions in Restricted Frequency Bands Restricted Band Emissions Limit Frequency Range (MHz)| Field Strength (uV/m) |Field Strength (dBuV/m)| Measure Distance (m) 0.009~0.490 2400/F(kHz) 48.5 — 13.8 300 0.490~1.705 24000/F(kHz) 33.8 — 23 30 1.705~30.0 30 29 30 30~88 100 40 3 88~216 150 43.5 3 216~960 200 46 3 Above 960 500 54 3 Note 1: Qusai—Peak value is measured for frequency below 1GHz except for 9—90 kHz, 110—490 kHz frequency band. Peak and average value are measured for frequency above 1GHz. The limit on average radio frequency emission is as above table. The limit on peak radio frequency emissions is 20 dB above the maximum permitted average emission limit Note 2: Measurements may be performed at a distance other than what is specified provided. When performing measurements at a distance other than that specified, the results shall be extrapolated to the specified distance using an extrapolation factor as below, Frequency at or above 30 MHz: 20 dB/decade Frequency below 30 MHz: 40 dB/decade. 3.5.2 Test Procedures 1. Measurement is made at a semi—anechoic chamber that incorporates a turntable allowing a EUT rotation of 360°. A continuously—rotating, remotely—controlled turntable is installed at the test site to support the EUT and facilitate determination of the direction of maximum radiation for each EUT emission frequency. The EUT is placed at test table. For emissions testing at or below 1 GHz, the table height is 80 cm above the reference ground plane. For emission measurements above 1 GHz, the table height is 1.5 m 2. Measurement is made with the antenna positioned in both the horizontal and vertical planes of polarization. The measurement antenna is varied in height (1m ~4m) above the reference ground plane to obtain the maximum signal strength. Distance between EUT and antenna is 3 m. 3. This investigation is performed with the EUT rotated 360°, the antenna height scanned between 1 m and 4 m, and the antenna rotated to repeat the measurements for both the horizontal and vertical antenna polarizations. Note: 1. 120kHz measurement bandwidth of test receiver and Quasi—peak detector is for radiated emission below 1GHz. 2. RBW=1MHz, VBW=3MHz and Peak detector is for peak measured value of radiated emission above 1GHz. 3. RBW=1MHz, VBW=1/T and Peak detector is for average measured value of radiated emission above 1GHz. Report No.: FR932003AE Page : 22 of 34 Report Version: Rev. 01

3.5.3 Test Setup Radiated Emissions below 1 GHz Radiated Emissions above 1 GHz Report No.: FR932003AE Page : 23 of 34 Report Version: Rev. 01

3.5.4 Transmitter Radiated Unwanted Emissions (Below 1GHz) Modulation GFSK Test Freq. (MHz) 2402 Polarization Horizontal Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Note 3: All spurious emissions below 30MHz are more than 20 dB below the limit. Report No.: FR932003AE Page : 24 of 34 Report Version: Rev. 01

Modulation GFSK Test Freq. (MHz) 2402 Polarization Vertical Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Note 3: All spurious emissions below 30MHz are more than 20 dB below the limit. Report No.: FR932003AE Page : 25 of 34 Report Version: Rev. 01

3.5.5 Transmitter Radiated Unwanted Emissions (Above 1GHz) for GFSK Modulation GFSK Test Freq. (MHz) 2402 Polarization Horizontal Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Report No.: FR932003AE Page : 26 of 34 Report Version: Rev. 01

Modulation GFSK Test Freq. (MHz) 2402 Polarization Vertical Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Report No.: FR932003AE Page : 27 of 34 Report Version: Rev. 01

Modulation GFSK Test Freq. (MHz) 2440 Polarization Horizontal Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Report No.: FR932003AE Page : 28 of 34 Report Version: Rev. 01

Modulation GFSK Test Freq. (MHz) 2440 Polarization Vertical Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Report No.: FR932003AE Page : 29 of 34 Report Version: Rev. 01

Modulation GFSK Test Freq. (MHz) 2480 Polarization Horizontal Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Report No.: FR932003AE Page : 30 of 34 Report Version: Rev. 01

Modulation GFSK Test Freq. (MHz) 2480 Polarization Vertical Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Report No.: FR932003AE Page : 31 of 34 Report Version: Rev. 01

3.6 Emissions in non-restricted Frequency Bands 3.6.1 Emissions in non-restricted frequency bands limit Peak power in any 100 kHz bandwidth outside of the authorized frequency band shall be attenuated by at least 20 dB relative to the maximum in-band peak PSD level in 100 kHz. 3.6.2 Test Procedures Reference level measurement 1. Set RBW=100kHz, VBW = 300kHz , Detector = Peak, Sweep time = Auto 2. Trace = max hold , Allow Trace to fully stabilize 3. Use the peak marker function to determine the maximum PSD level Emission level measurement 1. Set RBW=100kHz, VBW = 300kHz , Detector = Peak, Sweep time = Auto 2. Trace = max hold , Allow Trace to fully stabilize 3. Scan Frequency range is up to 25GHz 4. Use the peak marker function to determine the maximum amplitude level 3.6.3 Test Setup Report No.: FR932003AE Page : 32 of 34 Report Version: Rev. 01

3.6.4 Test Result of Emissions in non-restricted Frequency Bands Report No.: FR932003AE Page : 33 of 34 Report Version: Rev. 01

C Infernational Certification Corp. 4 Test laboratory information Established in 2012, ICC provides foremost EMC & RF Testing and advisory consultation services by our skilled engineers and technicians. Our services employ a wide variety of advanced edge test equipment and one of the widest certification extents in the business. International Certification Corp (EMC and Wireless Communication Laboratory), it is our definitive objective is to institute long term, trust—based associations with our clients. The expectation we set up with our clients is based on outstanding service, practical expertise and devotion to a certified value structure. Our passion is to grant our clients with best EMC / RF services by oriented knowledgeable and accommodating staff. Our Test sites are located at Linkou District and Kwei Shan District. Location map can be found on our website http://www.icertifi.com.tw. Linkou Kwei Shan Kwei Shan Site II Tel: 886—2—2601—1640 Tel: 886—3—271—8666 Tel: 886—3—271—8640 No. 30—2, Ding Fwu Tsuen, Lin No. 3—1, Lane 6, Wen San 3rd St., No. 14—1, Lane 19, Wen San 3rd Kou District, New Taipei City, Kwei Shan District, Tao Yuan City St., Kwei Shan District, Tao Yuan Taiwan, R.0.C. 333, Taiwan, R.O.C. City 333, Taiwan, R.O.C. If you have any suggestion, please feel free to contact us as below information. Tel: 886—3—271—8666 Fax: 886—3—318—0155 Email: ICC_Service@icertifi.com.tw ==END= Report No.: FR932003AE Page : 34 of 34 Report Version: Rev. 01


Document Created: 2019-06-18 07:51:15
Document Modified: 2019-06-18 07:51:15
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC