Cover Letters

FCC ID: ACJ9TAWX-SA250P

Cover Letter(s)

Download: PDF
FCCID_4325809

FCC Part 15D – Compliance Information EUT AND PRODUCT INFORMATION Type of Equipment UPCS (DECT 6.0) Applicant Name Panasonic Corporation Address 1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan Contact Katsuya Abe Telephone +81-50-3380-2468 Email abe.katsuya@jp.panasonic.com Brand Name Panasonic Base Station Handset / Portable WRS EUT Type/System ☒ ☒ ☐ FCC ID ACJ9TAWX-SA250P ACJ9TAWX-ST200P ACJ9TAWX-ST400P ISED ID (Canada) 216A-WXSA250P 216A-WXST200P 216A-WXST400P Model name WX-SA250P WX-ST200P WX-ST400P HW Version ES2 ES2 ES2 SW Version Main BBIC:v0.00R04 V1.01R99 Sub BBIC :v0.00R02 V1.01R99 Maximum Antenna Gain 2.95dBi 2.79dBi 0.61dBi Can the EUT be Initiating ☐ YES ☒ YES ☒ YES Device Does the EUT transmit ☒ YES ☐ YES ☒ YES signaling channels Max. # of slots in use 2 3 simultaneously Frequency Band 1921.536 – 1928.448 MHz Number of RF Channels 5 Frame Period 10 ms Max. Burst length 390usec / simplex channel (FP,PP) Min. Burst Length 390usec / simplex channel (FP,PP) Min. # of System Channels 60 (24 simplex channels per RF carrier) Supported DECT Slot Types ☒ Full Slot ☐ Long Slot ☐ Double Slot Operating Mode ☒ Simplex ☐ Duplex Nemko AS, Instituttveien 6, 2007 Kjeller, Norway pmbf-19-f001 fcc part 15d declarations_panasonic_a).docxTel: +47 22 96 03 30 Fax: +47 22 96 05 50 Page 1 (5) rev.2.9 06-Mar-2019 Email: frode.sveinsen@nemko.com

FCC Part 15D – Compliance Information ANTENNAS Base Station Antenna Type Internal External 1 Pattern Antenna(x4) ☒ ☐ 2 Planer Inverted F-type Antenna(x4) ☒ ☐ 3 ☐ ☐ 4 ☐ ☐ Does RX and TX use the same antenna(s)? ☒ Yes ☒ No Handset Antenna Type Internal External 1 Pattern Antenna ☒ ☐ 2 Planer Inverted F-type Antenna ☒ ☐ Does RX and TX use the same antenna(s)? ☒ Yes ☐ No ANTENNA DIVERSITY Antenna Diversity Supported TX RX Base Station 1 ☒ ☒ 2 ☒ ☒ 3 ☒ ☒ 4 ☒ ☒ Handset 1 ☒ ☒ 2 ☒ ☒ VOLTAGE AND TEMPERATURE RANGES VOLTAGES Base Station Handset or Portable WRS Nominal Voltage 24.0V 1.30V Cut-Off Voltage (if applicable) 8.1V 1.0V POWER SOURCE Type Manufacturer Base Station or WRS WX-SR202P(Receiver) Panasonic Handset (Charger) AA Battery - Connections on Base ☐ PSTN ☐ USB ☐ Ethernet ☒ Others (please specify) .... Nemko AS, Instituttveien 6, 2007 Kjeller, Norway pmbf-19-f001 fcc part 15d declarations_panasonic_a).docxTel: +47 22 96 03 30 Fax: +47 22 96 05 50 Page 2 (5) rev.2.9 06-Mar-2019 Email: frode.sveinsen@nemko.com

FCC Part 15D – Compliance Information ANCILLARY EQUIPMENT Description Type Manufacturer HOST DEVICE Description Type Manufacturer ADDITIONAL INFORMATION Nemko AS, Instituttveien 6, 2007 Kjeller, Norway pmbf-19-f001 fcc part 15d declarations_panasonic_a).docxTel: +47 22 96 03 30 Fax: +47 22 96 05 50 Page 3 (5) rev.2.9 06-Mar-2019 Email: frode.sveinsen@nemko.com

FCC Part 15D – Compliance Information MANUFACTURERS DECLARATIONS FCC part 15.323 (c)(5) The applicant declares that the system in this application has more than 20 duplex system access channels defined, and that the system is operating in Least Interfered Channel (LIC) mode in accordance with this section. Applicant Agrees ☒ Yes ☐ No FCC part 15.323 (c)(5) No device or group of co-operating devices located within 1m of each other shall during any frame period occupy more than 6 MHz of aggregate bandwidth, or alternatively, more than one third of the time and spectrum windows defined by the system. Applicant Agrees ☒ Yes ☐ No FCC part 15.323 (c)(10) The applicant hereby declares that the system in this application does use the criteria of (c)(10) of this section. Applicant Agrees ☒ Yes ☐ No FCC part 15.323 (c)(11) The applicant hereby declares that system in this application does not use the criteria of (c)(11) of this section. Applicant Agrees ☒ Yes ☐ No FCC part 15.323 (c)(12) The provisions of (c)(10) or (c)(11) of this section shall not be used to extend the range of spectrum occupied over space or time for the purpose of denying fair access to spectrum to other devices. Applicant Agrees ☒ Yes ☐ No ADDITIONAL REMARKS: > DECLARED BY: June 6, 2019 Ben Botros Nemko AS, Instituttveien 6, 2007 Kjeller, Norway pmbf-19-f001 fcc part 15d declarations_panasonic_a).docxTel: +47 22 96 03 30 Fax: +47 22 96 05 50 Page 4 (5) rev.2.9 06-Mar-2019 Email: frode.sveinsen@nemko.com

FCC Part 15D – Compliance Information About this document This document specifies the information that is needed to select the correct testcases and test procedures for testing to FCC Part 15D. The form must be completed by the applicant and submitted to Nemko before testing is started. Preparation of Equipment for Testing Note (a): Number of samples for testing The following samples are needed for FCC 15D testing: RF Conducted Tests: One sample with a 50 ohm antenna connector (preferably SMA Female). Only one antenna connector is needed for these tests even if the equipment has more than one antenna. Monitoring Tests: One sample with 50 ohm antenna connectors fitted to all antennas (preferably SMA female). Additionally we need a companion device that will work together with the EUT, the companion device must also have antenna connectors on all antennas. Radiated Tests: One sample with integral antennas. This sample will be used to measure Antenna Gain, Part 15B and Power-Line Conducted tests. Note (b): Burst Mode All RF tests are performed with the EUT in force transmit, aka burst mode. Software and necessary programming tools must be submitted to Nemko together with the test samples before start of testing. Note (c): Monitoring Tests Monitoring tests are performed in normal operating mode by establishing a connection from the handset (or the initiating device) to the base station (or the responding device). Most tests are performed by establishing connections from the initiating device to the responding device and observing which channel and/or timeslot is used. For monitoring tests we need a EUT and a Companion device that both have antenna connectors on all antennas (preferably SMA female, again). Additionally, we need access to the CLK100 signal on the Base Station, this is necessary because some of the tests require that the interferers are synced to the DECT frame. Note (d): Connection to an external power supply Means of connecting the equipment to an external power supply shall be supplied by the applicant together with the equipment to be tested. Battery operated equipment shall be supplied with the necessary batteries and chargers. All tests on battery operated equipment will be performed with batteries. Note (e): Test-Mode (Loopback Mode) Loopback Mode is usually not used for FCC testing. Nemko AS, Instituttveien 6, 2007 Kjeller, Norway pmbf-19-f001 fcc part 15d declarations_panasonic_a).docxTel: +47 22 96 03 30 Fax: +47 22 96 05 50 Page 5 (5) rev.2.9 06-Mar-2019 Email: frode.sveinsen@nemko.com


Document Created: 2019-06-07 15:47:36
Document Modified: 2019-06-07 15:47:36
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC