Test Report

FCC ID: A94-RC48S2-27

Test Report

Download: PDF
FCCID_168921

FCC ID: A94-RC48S2-27 TTI - P-G 009 / 98-00 TTI - P-G 089 / 94-50 E M I S S I O N -- T E S T R E P O R T Testreport file no. : T 20670-1-01 NF ______________ Date :_________________ July 17, 2001 of issue Model / Type No. : ______________________________________________ RC48T1-27 Kind of product : ______________________________________________ Remote Control (Audio / Video Products) Applicant : ______________________________________________ Bose Corporation Manufacturer : Bose Corporation ______________________________________________ Licence holder : ______________________________________________ Bose Corporation Address : ______________________________________________ The Mountain Framingham, MA, 01701, USA ______________________________________________ Test result accrdg. to the regulation(s) at page 3 : POSITIVE This testreport with appendix consists of 29 pages. The testresult only responds to the tested sample. It is not allowed to copy this report even partly without the allowance of the testlaboratory. File No. T 20670-1-01 NF , Page 1 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 DIRECTORY Page A) Documentation Directory ________ 2 Testregulations ________ 3 General information ________ 4-5 Discovery of worst case condition ________ 6 Equipment under Test ________ 16 Summary ________ 17 B) Testdata Conducted emissions 10/150 kHz - 30 MHz ________ 7 Spurious emissions (magnetic field) 10 kHz - 30 MHz ________ 8-9 Spurious emissions (electric field) 30 MHz - 1000 MHz ________ 10-11 Spurious emissions (electric field) 1 GHz - 18 GHz ________ 12-13 Raiated power of the fundamental wave ________ 14 Conducted power of the fundamental wave measured on ________ 15 the antenna terminals Attachment A) Testdata ________ A1-A4 B) List of Test Equipment ________ B1 C) Photos of the test setup ________ C1 D) Technical description of the test sample ________ D1-D3 (e.g.CDF, Declaration) E) Photos of the EuT ________ E1-E3 F) Measurement Protocol for FCC, VCCI and AUSTEL ________ -- File No. T 20670-1-01 NF , Page 2 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 TESTREGULATIONS The tests were performed according to following regulations : o - EN 50081-1 / 2.1991 o - EN 50081-2 / 7.1993 -------------------------------------------------------------------------------- o - EN 55011 / 3.1991 o - Group 1 o - Group 2 o - class A o - class B o - EN 55014 / 4.1993 o - Household appliances and similar o - tools o - Semiconductor devices o - EN 55014 / A2:1990 o - EN 55104 / 5.1995 Category: o - EN 55015 / A1:1990 o - EN 55015 / 12.1993 o - EN 55022 / 5.1995 o - class A o - class B o - prEN 55103-1 / 3.1995 o - prEN 50121-3-2 / 3.1995 o - EN 60601-1-2 / 4.1994 o - VCCI o - class 1 o - class 2 n - Part 15 Subpart C (15.227) o - Part 15 Subpart C (15.209) File No. T 20670-1-01 NF , Page 3 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 ADDRESS OF THE TEST LABORATORY n - MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 D - 94342 Strasskirchen o - ______________________________________ ______________________________________ ______________________________________ ENVIRONMENTAL CONDITIONS Temperature: ______ 15-35 ° C Humidity ______ 45-60 % Atmospheric pressure _________ 860-1060 mbar POWER SUPPLY SYSTEM UTILIZED Power supply system : Battery Unom = 6.0 V DC STATEMENT OF MEASUREMENT UNCERTAINTY The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities that can account for a nominal measurement error of ±4dB. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. SHORT DESCRIPTION OF THE EQUIPMENT UNDER TEST (EUT) The EuT is a Remote Control to operate audio and video units/systems. Number of received/tested samples: 1 / 1 Serial Number: Preproduction Sample DEFINITIONS FOR SYMBOLS USED IN THIS TEST REPORT n - Black box indicates that the listed condition, standard or equipment is applicable for this Report. o - Blank box indicates that the listed condition, standard or equipment was not applicable for this Report. File No. T 20670-1-01 NF , Page 4 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 M E A S U R E M E N T P R O T O C O L F O R F C C , V C C I A N D A U S T E L Test Methodology Conducted and radiated emission testing is performed according to the procedures in International Special Committee on Radio Interference (CISPR) Publication 22 (1993), European Standard EN 55022 and Australian Standard AS 3548 (which are based on CISPR 22). The Japanese standard, "Voluntary Control Council for Interference (VCCI) by Data Processing Equipment and Electronic Office Machines, Technical Requirements" is technically equivalent to CISPR 22 (1993). For official compliance, a conformance report must be sent to and accepted by the VCCI. In compliance with FCC Docket 92-152, "Harmonization of Rules for Digital Devices Incorporate International Standards", testing for FCC compliance may be done following the ANSI C63.4-1992 procedures and using the FCC limits or the CISPR 22 Limits. Measurement Error The test system for conducted emissions is defined as the LISN, tuned receiver and coaxial cable. The test system for spurious emissions is defined as the antenna, the pre-amplifier, the tuned receiver and the coaxial cable. These test systems have an expected error of ±3 dB. The equipment comprising the test systems are calibrated on an annual basis. Justification The Equipment Under Test (EUT) is configured in a typical user arrangement in accordance with the manufacturer's instructions. A cable is connected to each available port and either terminated with a peripheral into it’s characteristic impedance or left unterminated. When appropriate, the cables are manually manipulated with respect to each other to obtain maximum emissions from the unit. General Standard Information The test methods used comply with CISPR Publication 22 (1993), EN 55022 (1987) and AS 3548 (1992) - "Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology Equipment" and with ANSI C63.4-1992 - "Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz." For detailed description of each measurement please refer to section testresults. File No. T 20670-1-01 NF , Page 5 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 DISCOVERY OF WORST CASE MEASUREMENT CONDITION: The Remote Control RC48T1-27 is designed for the operation at a fixed transmitter frequency of 27.145 MHz. To find out the worst case conditions for the complete measurement the following tests have been performed: • Measurement of the radiated fieldstrength of the operating frequency measured in permanent operation mode in the specified channel. This measurement have been performed in order to find out the maximum transmitted fieldstrength of the Remote Control. • Measurement of the radiated spurious emissions measured in permanent operation mode in the specified channel. This measurement have been performed in order to find out the maximum spurious emissions of the Remote Control. Based on this testresults, the measurements have been performed completely on the specified channel. This testresults are documented in the following sections of the testreport. File No. T 20670-1-01 NF , Page 6 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 TESTRESULT CONDUCTED EMISSIONS - 10/150 kHz - 30 MHz n - Test not applicable Testlocation : o - Shielded room no. 1 o - Shielded room no. 2 o - Shielded room no. 3 o - Shielded room no. 4 o - Shielded room no. 5 o - Shielded room no. 6 o - Shielded room no. 7 o - Anechoic chamber o - Full compact chamber For TEST EQUIPMENT USED please refer to ATTACHMENT B: ¯¯¯¯¯¯¯¯ Description of Measurement The final level, expressed in dBµV, is arrived at by taking the reading directly from the EMI receiver. This level is compared directly to the FCC Limit or to the CISPR limit, which is equivalent to the Australian AS 3548 limit. To convert between dBµV and µV, the following conversions apply: dBµV = 20(log µV) µV = Inverse log(dBµV/20) Conducted emissions on the 50 Hz and/or 60 Hz power interface of the EUT are measured in the frequency range of 150 kHz to 30 MHz. The measurements are performed using a receiver, which has CISPR characteristic bandwidth and quasipeak detection, and a Line Impedance Stabilization Network (LISN), with 50Ω /50 µH (CISPR 16) characteristics. Table top equipment is placed on a non-conducting table 80 centimeters above the floor and is positioned 40 centimeters from the vertical ground plane (wall) of the screen room. If the minimum passing margin appears to be less than 20 dB with a peak mode measurement, the emissions are remeasured using a tuned receiver with quasipeak and average detection and recorded on the data sheets. Testresult The requirements are O - MET O - NOT MET Min. limit margin _______ dB at _______ MHz Max. limit exceeding _______ dB at _______ MHz Remarks: _________________________________________________________________ NOT APPLICABLE _________________________________________________________________ SPURIOUS EMISSION Spurious emissions from the EUT are measured in the frequency range of 9 kHz to 30 MHz using a tuned receiver and a shielded loop antenna. The antenna was positioned 3, 10 or 30 meters horizontally from the EUT. Measurements have been made in all three orthogonal axes and the shielded loop antenna was rotated to locate the maximum of the emissions. Spurious emissions from the EUT are measured in the frequency range of 30 MHz to 10 times the highest used frequency using a tuned receiver and appropriate broadband linearly polarized antennas. Measurements between 30 MHz and 1000 MHz are made with 120 kHz/6 dB bandwidth and quasipeak detection and measurements above 1000 MHz are made with a 1 MHz/6 dB bandwidth and peak detection, remeasurement of results which may be critical will be repeated in average mode. Table top equipment is placed on a 1.0 X 1.5 meter non-conducting table 80 File No. T 20670-1-01 NF , Page 7 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 centimeters above the ground plane. Floor standing equipment is placed directly on the turntable/ground plane. Interface cables that are closer than 40 centimeters to the ground plane are bundled in the center in a serpentine fashion so they are at least 40 centimeters from the ground plane. Cables to simulators/testers (if used in this test) are routed through the center of the table and to a screen room located outside the test area. The antenna was positioned 3, 10 or 30 meters horizontally from the EUT. To locate maximum emissions from the test sample the antenna is varied in height from 1 to 4 meters, measurement scans are made with both horizontal and vertical antenna polarizations and the EUT are rotated 360 degrees. SPURIOUS EMISSION (MAGNETIC FIELD) 9 kHz - 30 MHz n - Test not applicable o - in a shielded room o - at a non - reflecting open-site and o - in a testdistance of 3 meters. o - in a testdistance of 30 meters. For TEST EQUIPMENT USED please refer to ATTACHMENT B: SER1 ¯¯¯¯¯¯¯¯ Description of Measurement The final level, expressed in dBµV/m, is arrived at by taking the reading from the EMI receiver (Level dBµV) and adding the antenna correction factor and cable loss factor (Factor dB) to it. This result then has to be compared with the relevant FCC limit. The resolution bandwidth during the measurement is as follows: 9 kHz – 150 kHz: ResBW: 200 Hz 150 kHz – 30 MHz: ResBW: 10 kHz Example: Frequency Level + Factor = Level Limit = Delta (MHz) (dBµV) (dB) (dBµV/m) (dBµV/m) (dB) 1.705 5 + 20 = 25 30 = 5 File No. T 20670-1-01 NF , Page 8 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 Testresult in detail: Frequency L: PK L: AV L: QP Correct. L: PK L: AV L: QP Limit [MHz] [dBµV] [dBµV] [dBµV] [dB] [dBµV/m] [dBµV/m] [dBµV/m] [dBµV/m] The requirements are O - MET O - NOT MET Min. limit margin _______ dB _______ MHz Min. limit margin _______ dB _______ MHz Remarks: _________________________________________________________________ _________________________________________________________________ _________________________________________________________________ _________________________________________________________________ _________________________________________________________________ File No. T 20670-1-01 NF , Page 9 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 SPURIOUS EMISSIONS (electric field) 30 MHz - 1000 MHz o - Test not applicable n - Open-site 1 o - Open-site 2 n - 3 meters o - 10 meters o - 30 meters For TEST EQUIPMENT USED please refer to ATTACHMENT B: SER2 ¯¯¯¯¯¯¯¯ Description of Measurement The final level, expressed in dBµV/m, is arrived by taking the reading from the EMI receiver (Level dBµV) and adding the correction factors and cable loss factor (Factor dB) to it. This is done automatically in the EMI receiver, where the correction factors are stored. This result then has the FCC or CISPR limit subtracted from it to provide the Delta which gives the tabular data as shown in the data sheets at page 24 - 25. The CISPR 22 limit is equivalent to the Australian AS 3548 limit. Example: Frequency Level + Factor = Level Limit = Delta (MHz) (dBµV) (dB) (dBµV/m) (dBµV/m) (dB) 719 75 + 32.6 = 107.6 110 = -2.4 Frequency L: PK L: AV L: QP Correct. L: PK L: AV L: QP Limit [MHz] [dBµV] [dBµV] [dBµV] [dB] [dBµV/m] [dBµV/m] [dBµV/m] [dBµV/m] 81.7 21.0 1.0 17.0 13.5 34.5 14.5 30.5 40.0 File No. T 20670-1-01 NF , Page 10 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 Testresult The requirements are n - MET O - NOT MET Min. limit margin _______ 9.5 dB _______ 81.7 MHz Min. limit margin _______ dB _______ MHz Remarks: _________________________________________________________________ The limits are kept. _________________________________________________________________ The measurement was performed up to the 10th harmonic _________________________________________________________________ (271.45 MHz) _________________________________________________________________ _________________________________________________________________ File No. T 20670-1-01 NF , Page 11 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 SPURIOUS EMISSION 1 GHz - 18 GHz n - Test not applicable Testlocation : o - Open-site 1 o - Open-site 2 o - Anechoic chamber o - Full compact chamber o - 1 meters o - 3 meters o - 10 meters For TEST EQUIPMENT USED please refer to ATTACHMENT B: ¯¯¯¯¯¯¯¯ Description of Measurement The final level, expressed in dBµV/m, is arrived by taking the reading from the Spectrumanalyzer in dBµV and adding the correction factors of the test setup incl. cables. Example of the correction value at 1.8 GHz Level reading Correction correction Correction corrected at EMCO 3115 Amplifier Factor level 1.8 GHz AWT 4534 + cable (summarized) 56 dBµV +27.3 dB -41.2 dB -15.8 dB 42.1 dBµV/m Testresult in detail: Frequency L: PK L: AV L: QP Correct. L: PK L: AV L: QP Limit [MHz] [dBµV] [dBµV] [dBµV] [dB] [dBµV/m] [dBµV/m] [dBµV/m] [dBµV/m] File No. T 20670-1-01 NF , Page 12 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 Testresult The requirements are O - MET O - NOT MET Min. limit margin _______ dB _______ MHz Min. limit margin _______ dB _______ MHz Remarks: _________________________________________________________________ NOT APPLICABLE _________________________________________________________________ _________________________________________________________________ File No. T 20670-1-01 NF , Page 13 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 FIELD STRENGTH OF THE FUNDAMENTAL WAVE o - Test not applicable n - Open-site 1 o - Open-site 2 n - 3 meters o - 10 meters o - 30 meters For TEST EQUIPMENT USED please refer to ATTACHMENT B: CPR2 ¯¯¯¯¯¯¯¯ Description of Measurement The final level, expressed in dBµV/m, is arrived by taking the reading from the EMI receiver (Level dBµV) and adding the correction factors and cable loss factor (Factor dB) to it. This is done automatically in the EMI receiver, where the correction factors are stored. This result then has the FCC or CISPR limit subtracted from it to provide the Delta which gives the tabular data as shown in the data sheets at page 24 - 25. The CISPR 22 limit is equivalent to the Australian AS 3548 limit. Example: Frequency Level + Factor = Level - Limit = Delta (MHz) (dBµV) (dB) (dBµV/m) (dBµV/m) (dB) 315 45 + 22.5 = 67.5 - 74.3 = -6.8 Testresult in detail: Frequency L: PK L: AV L: QP Correct. L: PK L: AV L: QP Limit [MHz] [dBµV] [dBµV] [dBµV] [dB] [dBµV/m] [dBµV/m] [dBµV/m] [dBµV/m] 27.145 55.0 35.0 50.8 +11 66.0 46.0 61.8 80.0 Testresult The requirements are n - MET O - NOT MET Min. limit margin _______ >10.0 dB _______ 27.145 MHz Min. limit margin _______ dB _______ MHz Remarks: _________________________________________________________________ The limits are kept. Duty factor correction was not calculated, _________________________________________________________________ because the Peak-level meets the AV-limit. File No. T 20670-1-01 NF , Page 14 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 CONDUCTED POWER OF THE FUNDAMENTAL WAVE MEASURED ON THE ANTENNA TERMINALS n - Test not applicable Testlocation : o - Shielded room no. 1 o - Shielded room no. 2 o - Shielded room no. 3 o - Shielded room no. 4 o - Shielded room no. 5 o - Shielded room no. 6 o - Shielded room no. 7 o - Anechoic chamber o - Full compact chamber o - Climatic test chamber VLK For TEST EQUIPMENT USED please refer to ATTACHMENT B: ¯¯¯¯¯¯¯¯ Description of Measurement The conducted power of the fundamental wave measured on the antenna terminals in a climatic test chamber. The antenna jack was connected to the input of a communication test receiver. The internal batteries have been removed also and a variable DC power supply was used instead. The measurements have been made with the EUT unmodulated. During the test the supply voltage and the temperature were varied and applied simultaneously. The lower supply voltage was given by the manufacturer. In case the equipment was switching off before, the switch off voltage was used instead. Testresult The requirements are O - MET O - NOT MET Frequency range of equipment Tempera- DC supply Power/dBm Power/dBm Power/dBm Power/dBm Power/dBm Power/dBm Power/dBm ture/°C voltage/V -30 -20 -10 0 +10 +20 +30 +40 +50 Remarks: _________________________________________________________________ NOT APPLICABLE File No. T 20670-1-01 NF , Page 15 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 EQUIPMENT UNDER TEST Operation - mode of the EUT.: The equipment under test was operated during the measurement under following conditions: o - Standby o - Testprogram (H - Pattern) o - Testprogram (color bar) o - Testprogram (customer specific) n ______________________________________________________________________ - Transmit at a fixed frequency of 27.145 MHz. o ______________________________________________________________________ - ______________________________________________________________________ o - Configuration of the equipment under test: Following periphery devices and interface cables were connected during the measurement: o ____________________________ - Type : __________________________ o ____________________________ - Type : __________________________ o ____________________________ - Type : __________________________ o ____________________________ - Type : __________________________ o ____________________________ - Type : __________________________ o ____________________________ - Type : __________________________ o - unshielded power cable o - unshielded cables o - shielded cables MPS.No.: o- customer specific cables o -___________________________________________________________________ o -___________________________________________________________________ File No. T 20670-1-01 NF , Page 16 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

FCC ID: A94-RC48S2-27 SUMMARY GENERAL REMARKS: The product RC48T1-27 has been tested on the following frequency: TX-Mode: 27.145 MHz FINAL JUDGEMENT: The requirements according to the technical regulations and tested operation modes are n - met. o - not met. The equipment under test n - Fulfills the general approval requirements cited on page 3. o - Does not fulfill the general approval requirements cited on page 3. Date of receipt of test sample : _________________________ accdg. to storage record Testing Start Date : _______________________ May 30, 2001 Testing End Date : _______________________ Juni 12, 2001 - MIKES BABT PRODUCT SERVICE GmbH - Test-engineer i.V. _______________________________ _____________________________ Günter Mikes Nikolaus Fischer Dipl.-Ing.(FH) File No. T 20670-1-01 NF , Page 17 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.6

Tue 2001 Jun 12 08‘ 41 FEF 90.0 dBupV MEKR 27.147 MHz Kunde: 10dB/ A_MHax Pos i __B_Blank Norm 80 .36 dBuV Gerat: & ConmrpReot Modell: Ser.Nr.: Norm: * 7 Bemerkung: 1bel2. CENTER 27.145 MHz SPAN 2.000 MHz *PBW 1 kHz VBWY 1 kHz SWP 4.0 s *ATT 109B Preanp AA of A4

Tue 2001 Jun 12 08 :39 : _7~ 20 REF 90.0 dBu¥ MEKR 27.151 MHz Kunde: oSR 10d4B/ A_Max Pos i __B_Blank Nornm 83.35 «dBpV Gerat: @reore Modell: Mc Ser.Nr.: Norm: Bemerkung: //aé/z CENTER 27.145 MHz SPAN 2.000 MHz [*RBW 10 kHz VBW 10 kHz SWP 40 ns __*#ATT 104B : Preamp Az2 or Au

Tue 2001 Jun 12 08 :38 .: C ¥o EF 90.0 dBu¥ MKR 27.147 MHz Kunde: S 1048 / A_Max Pos i B_B Tank Norm 83.63 dBuV¥ Gerat: Kpkf10]T2 COfeSJTReL Modell: C Ser.Nr.: Norm: U /4 Bemerkung: ied é’é’z_ l _ ‘\W M~ ENTER 27 .145 MHz SPAN 2.000 MHz #PBW 30 kHz YBW 30 kHz ___SWP 20 ms __# T 10dB *AT _ Preanp A3 oF A4 \

Tue 2001 Jun 12 908 :36 FPEF 90.0 dBuV MEKR 27.147 MHz 10dB / f#_Max Posi _B_Blank Norn 82.74 dBuV¥ *\ Bemerkung: 400 beffe. A CENTER 27.145 MHz SPAN 2.000 HMHz *PBY 100 kHz YBY100 kHz SWP 20 ms *#ATT 1006 . Preamp

mfilk@f BA)BT Attachment : B List of Test Equipment All test instruments used, in addition to the test accessories, are calibrated and verified regularly. Test Report No: T 20670—1—01 NF Beginning of Testing: 30—Mai—2001 Test ID Model Type Kind of Equipment Manufacturer Equipment No. CPR2 HCC Controller Ant.—Mast Rohde & Schwarz Miinchen 04—07/59—97—001 RG 214 U Antenna cable 2 m Huber+Suhner 04—07/60—89—463 HF 7/8 inch Antenna cable 13 m Huber+Subner 04—07/60—99—001 HF 7/8 inch Antenna cable 20 m Huber+Subner 04—07/60—99—002 HF 7/8 inch Antenna cable 40 m Huber+Suhner 04—07/60—99—003 KR — 200 Coax Antenna Switch Rosenberger HF—Technik 04—07/60—99—004 VULB — 9165 Super—Broadband—Anten Schwarzbeck G. 04—07/62—00—001 ESVP Test Receiver Rohde & Schwarz Miinchen 04—07/63—89—008 ESVP—EZM Spectrum Monitor Rohde & Schwarz Miinchen 04—07/74—86—016 Antennenmast Antenna mast Rohde & Schwarz Miinchen {04—07/92—97—001 MB 27 MHz—Antenna Rod Antenna MIKES PRODUCT SERVICE 04—07/62—97—001 R 3162 Spectrum Analyzer Advantest 04—07/74—00—001 SER2 HCC Controller Ant.—Mast Rohde & Schwarz Miinchen 04—07/59—97—001 RG 214 U Antenna cable 2 m Huber+Suhner 04—07/60—89—463 HF 7/8 inch Antenna cable 13 m Huber+Suhner 04—07/60—99—001 HF 7/8 inch Antenna cable 20 m Huber+Subhner 04—07/60—99—002 HF 7/8 inch Antenna cable 40 m Huber+Subner 04—07/60—99—003 KR — 200 Coax Antenna Switch Rosenberger HF—Technik 04—07/60—99—004 VULB — 9165 Super—Broadband—Anten Schwarzbeck G. 04—07/62—00—001 ESVP Test Receiver Rohde & Schwarz Miinchen 04—07/63—89—008 ESVP—EZM Spectrum Monitor Rohde & Schwarz Miinchen 04—07/74—86—016 Antennenmast Antenna mast Rohde & Schwarz Miinchen 04—07/92—97—001 MIKES BABT Product Service GmbH Ohmstrasse 2—4, 94342 Strasskirchen Tel: +49 9424—9407—0 Fax: +49 9424—9407—60 moemmmmnemmes on mm conmmmmommememmmmen mmummcmmmmmomecmmenmmmnnen ao

CONSTRUCTIONAL DATAFORM FOR TESTING OF RADIO EQUIPMENT Licence holder: Bose Corporation Address: The Mountain, Framingham, MA, 01701, USA Manufacturer: Bose Address: Type: Remote control Model: RC28T1—27, RC28T2—27, RC288S2—27 RC48T1—27, RC48T2—27, RC48S2—27 Serial—No.: Ji'—‘rotection class: rll Additional informations to the above named model: Antenna: transmitter: Type: Internal Length/size: 45mm receiver: Type: Not applicable Length/size: Not applicable Power supply of the transmitter: Type: Battery (AAA x 4) nominal voltage: 6.0 lowest voltage: highest voltage: Power supply of the receiver: Type: nominal voltage: V Ancillary equipment: Description: None. Type: Serial—no.: Description: Type: Serial—no.: Description: Type: * Serial—no.: Extreme temperature range in which the approval test should be performed: X Category I: General (—20°C to +55°C) O Category II: Portable {—10°C to +55°C) O Category I!I: Equipment for normal indoor use (0°C to +55°C) Connectable cables: Name of the cable Digital Length/m shielded None. O yes O no O yes O no O yes O no O yes O no Oyes O no O yes O no O if applicable, if necessary complete overieat Page D1 MIKES BABT PRODUCT SERVICE GmbH Ohmstr. 24 D—94342 Strasskirchen Tel.: +49 94 24 94 07—0 Fax.: +49 94 24 94 07—60 Rev.No.: 2.1

Applicant: BOSE Model—name: RC 28 / 48 Type designation: RC28T1—27, RC28T2—27, RC28S2—27 RC48T1—27, RC48T2—27, RC48S2—27 Name and type designation of individual units comprising the radio equipment: Type of equipment: {Q Radiotelephone X Remote—control C Radiomaritime 0 LPD equipment equipment equipment { One—way O Inductive loop system O Inland waterways L RLAN radiotelephone equipment equipment {Q Personal paging C Radio—relay system 0 Radionavigation system equipm. C Satellite earth station { CB radiotelephone O Antenna equipment C Data transmission L Movement detector { Aeronautical equipment equipment Technical characteristics: Transmitter—receiver Transmitter Receiver Frequency range 27.145 MHz Maximum no. of channels 1 Channel spacing 10 kHz Class of emission 10KOA1D (type of modulation) Maximum RF output power Maximum effective ~10 dBm radiated power (ERP) Output power variable _—— Channel switching an= frequency range Method of frequency C Synthesizer X Crystal Q Other generation Frequency generation TX Frequency generation RX IF 1st IF | 2nd IF 3rd IF integral selective calling _| Audio—frequency interface level at external data socket Modes of operation [ 0 Duplex mode C Semi—duplex mode X Simplex mode Power source [ 0 Mains L Vehicle—regulated X _integral Antenna socket C BNC O TNC C N {Q M 0 UHF Q Adapter X None o 0 Test specifications: O If applicable, if necessary complete overieaf MIKES BABT PRODUCT SERVICE GmbH Ohmstr. 2—4 D—94342 Strasskirchen Tel.: +49 94 24 94 07—0 Fax.: +49 94 24 94 07—60

Applicant: BOSE Model—name: RC 28 / 48 Declarations: E_ We declare that the above information are correct and the named model was supplied with the maximum configuration to the accredited test laboratory. WJ PM _ame PBTb O) Qw { /M Seal and signature of applicant O If applicable, if necessary complete overleaf Page D 3 MIKES BABT PRODUCT SERVICE GmbH Ohmstr. 24 D—94342 Strasskirchen Tel.: +49 94 24 94 07—0 Fax.: +49 94 24 94 07—60 Rev.No.: 3.2


Document Created: 2001-09-07 09:50:31
Document Modified: 2001-09-07 09:50:31
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC