Manual

FCC ID: A8TBM71S2

Users Manual

Download: PDF
FCCID_2861450

BM71 Regulatory Compliance Information BM71 Regulatory Compliance Information Revision 0.4 Dec’ 2015 Advance Information Revision 0.4 12/2015 DS60001372C-Page 53

BM71 Regulatory Compliance Information This document covers the Regulatory Compliance information which is part of the BM71 Module datasheet and related documents shared with customers. Advance Information Revision 0.4 12/2015 DS60001372C-Page 54

BM71 Regulatory Compliance Information 1.0 ANTENNA 1.1 Antenna Characteristics 1.1.1 CERAMIC CHIP ANTENNA The BM71 module contains an integral ceramic chip antenna. The Figure 1-1 illustrates the antenna performance of the module. FIGURE 1-1: BM71 ANTENNA RADIATION PATTERN Frequency 2442 MHz Max Gain 0.1 dBi Efficiency 42.7% Advance Information Revision 0.4 12/2015 DS60001372C-Page 55

BM71 Regulatory Compliance Information APPENDIX A: CERTIFICATION devices, computer peripherals, radio receivers, etc.; and to additional authorization requirements for the NOTICES non-transmitter functions on the transmitter module Note: This device has no been au orized as (i.e., Verification, or Declaration of Conformity) (e.g., required by the rules of the ederal Com- transmitter modules may also contain digital logic func- munications Commission This device is tions) as appropriate. no and may not be, offered or sale or leas or sold or leased, until au orization A.1.2 LABELING AND USER is obtained INFORMATION REQUIREMENTS The BM71 module has to be labeled with its own FCC BM71 module regulatory approval status: ID number, and if the FCC ID is not visible when the • BT SIG/QDID:74246 module is installed inside another device, then the out- • United States/FCC ID: A8TBM71S2 side of the finished product into which the module is • Canada/IC ID: 12246A-BM71S2 installed must also display a label referring to the enclosed module. This exterior label can use wording HVIN: BM71BLES1FC2 as follows: • Europe/CE: In Progress • Japan/MIC: 005-101150 Contains Transmitter Module FCC ID: • Korea/KCC: MSIP-CRM-mcp-BM71BLES1FC2 A8TBM71S2 • Taiwan/NCC No: In Progress or Contains FCC ID: A8TBM71S2 A.1 REGULATORY APPROVAL This device complies with Part 15 of the FCC Rules. This section outlines the regulatory information for the Operation is subject to the following two conditions: BM71 module for the following countries: (1) this device may not cause harmful interference, and (2) this device must accept any interference • United States received, including interference that may cause • Canada undesired operation • Europe Due to the limited module size (9.0 x 11.5mm) the • Japan FCC Identifier is displayed in the Datasheet only and • Korea cannot be displayed on the module label. • Taiwan A.1.1 UNITED STATES The BM71 module is in progress to receive Federal Communications Commission (FCC) CFR47 Telecom- munications, Part 15 Subpart C "Intentional Radiators" modular approval in accordance with Part 15.212 Mod- ular Transmitter approval. Modular approval allows the end user to integrate the BM71 module into a finished product without obtaining subsequent and separate FCC approvals for intentional radiation, provided no changes or modifications are made to the module cir- cuitry. Changes or modifications could void the user's authority to operate the equipment. The end user must comply with all of the instructions provided by the Grantee, which indicate installation and/or operating conditions necessary for compliance. The finished product is required to comply with all appli- cable FCC equipment authorizations regulations, requirements and equipment functions not associated with the transmitter module portion. For example, com- pliance must be demonstrated to regulations for other transmitter components within the host product; to requirements for unintentional radiators (Part 15 Sub- part B "Unintentional Radiators"), such as digital Advance Information Revision 0.4 12/2015 DS60001372C-Page 54

BM71 Regulatory Compliance Information A user's manual for the finished product should include the following statement: A.1.4 HELPFUL WEB SITES is equipment has been tested and found o comply Federal Communications Commission (FCC): wi he limi for a Class B digi l device pursuan o http://www.fcc.gov pa 15 of the FCC Rule These limi s are designed FCC Office of Engineering and Technology (OET) Lab- provide reasonable protection agains ha ul oratory Division Knowledge Database (KDB): in erence in a residential ins allation. his equip- http://apps.fcc.gov/oetcf/kdb/index.cfm ment generate uses and can radiate radio fre- quency energy and if no ins alled and used in accordance wi h he in ru ions may cause harmful in erence to radio communic ions However ere is no guaran ee hat in nce will not occur in a par icular in lla ion his equipmen does cause harmful in nce to radio or television recep io which can be determined by urning the equipment of and on, the user is encouraged to ry to corre the in erence by one or more o the follow- ing measures • Reorien or reloca e he receiving an enn • ncrease the separation between he equipment and receiver • Connec he equipmen in an outlet on a circui di eren from hat which the receiver is con- ne ed. • Consult he dealer or an experienced radio chnician for help. Additional information on labeling and user information requirements for Part 15 devices can be found in KDB Publication 784748 available at the FCC Office of Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB) http://apps.fcc.gov/oetcf/kdb/index.cfm. A.1.3 RF EXPOSURE All transmitters regulated by FCC must comply with RF exposure requirements. KDB 447498 General RF Exposure Guidance provides guidance in determining whether proposed or existing transmitting facilities, operations or devices comply with limits for human exposure to Radio Frequency (RF) fields adopted by the Federal Communications Commission (FCC). From the FCC Grant: Output power listed is conducted. This grant is valid only when the module is sold to OEM integrators and must be installed by the OEM or OEM integrators. This transmitter is restricted for use with the specific antenna(s) tested in this application for Certification and must not be co-located or operating in conjunction with any other antenna or transmitters within a host device, except in accordance with FCC multi-transmitter product procedures. Advance Information Revision 0.4 12/2015 DS60001372C-Page 55

BM71 Regulatory Compliance Information tus shall contain the following or equivalent notice in a A.2 Canada conspicuous location in the user manual or alterna- tively on the device or both: The BM71 module certification is in progress for use in Canada under Industry Canada (IC) Radio Standards is device complies wi ndu Canada Specification (RSS) RSS-247 and RSS-Gen. Modular license-exem R andard(s) pera ion is sub- approval permits the installation of a module in a host je to the ollowing two condi ions (1) this device device without the need to recertify the device. may not cause interferenc and (2) this device mu Certification details: accept any interference including in nce h IC Certification Number: 12246A-BM71S2 ay cause undesired operation o the device HVIN: BM71BLES1FC2 Le présen appareil es con orme aux CNR d dus- trie Canada applicables aux appareils radio exemp s A.2.1 LABELING AND USER de licence L'exploi ation es autorisée aux deux con- INFORMATION REQUIREMENTS ditions suivant (1) l appareil ne doit pas produire Labeling Requirements for the Host Device (from Sec- de brouillage, (2) l'utilisateur de l appareil doit tion 3.1, RSS-Gen, Issue 4, November 2014): The host accepter out brouillage radioélec rique subi même device shall be properly labeled to identify the module si le brouillage es susceptible d'en comprome re le within the host device. nctionneme The Industry Canada certification label of a module Transmitter Antenna (from Section 8.3, RSS-Gen, shall be clearly visible at all times when installed in the Issue 4, November 2014): User manuals for transmit- host device, otherwise the host device must be labeled ters shall display the following notice in a conspicuous to display the Industry Canada certification number of location: the module, preceded by the words "Contains transmit- ter module", or the word "Contains", or similar wording Under Industry Canada regulations, this radio trans- expressing the same meaning, as follows: mitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the trans- mitter by Industry Canada. To reduce potential radio Co ains transmitter module interference to other users, the antenna type and its gain should be so chosen that the equivalent isotrop- ically radiated power (e.i.r.p.) is not more than that Due to the limited module size (9.0 x 11.5mm) the IC necessary for successful communication. identifier is displayed in the Datasheet only and Conformément à la réglementation d'Industrie Can- cannot be displayed on the module label. ada, le présent émetteur radio peut fonctionner avec User Manual Notice for License-Exempt Radio Appara- une antenne d'un type et d'un gain maximal (ou tus (from Section 8.4, RSS-Gen, Issue 4, November inférieur) approuvé pour l'émetteur par Industrie Can- 2014): User manuals for license-exempt radio appara- ada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établisse- ment d'une communication satisfaisante. The above notice may be affixed to the device instead of displayed in the user manual. Advance Information Revision 0.4 12/2015 DS60001372C-Page 56

BM71 Regulatory Compliance Information A.2.2 RF EXPOSURE Note: o main ain conformance to the testing All transmitters regulated by IC must comply with RF li ed in Table A-1 European Compliance exposure requirements listed in RSS-102 - Radio Fre- es ing the module shall be ins alled in quency (RF) Exposure Compliance of Radio communi- accordance wi the in allation in cation Apparatus (All Frequency Bands). ons in this data sheet and shall no be modified A.2.3 HELPFUL WEB SITES When integra ing a radio module into a Industry Canada: http://www.ic.gc.ca/ comple ed produc he in grator becomes the manuf urer of the final A.3 Europe produ and is therefore responsible for demons ng compliance of the final The BM71 module is in progress to be an R&TTE produ wi h the essen ial requirements of Directive assessed radio module that is CE marked the R&TTE Direc ive and has been manufactured and tested with the inten- tion of being integrated into a final product. A.3.1 LABELING AND USER The BM71 module has been tested to R&TTE Directive INFORMATION REQUIREMENTS 1999/5/EC Essential Requirements for Health and The label on the final product which contains the BM71 Safety (Article (3.1(a)), Electromagnetic Compatibility module must follow CE marking requirements. The (EMC) (Article 3.1(b)), and Radio (Article 3.2) and are R&TTE Compliance Association Technical Guidance summarized in Table A-1. A Notified Body Opinion can Note 01 provides guidance on final product CE mark- be arranged on request. ing. The R&TTE Compliance Association provides guid- ance on modular devices in “Technical Guidance Note A.3.2 ANTENNA REQUIREMENTS 01” document available for download from the following From R&TTE Compliance Association document Tech- location: http://www.rtteca.com/html/down- nical Guidance Note 01. load_area.htm. Provided the integrator installing an assessed radio module with an integral or specific antenna and installed in conformance with the radio mod- ule manufacturer's installation instructions requires no further evaluation.Under Article 3.2 of the R&TTE Directive and does not require fur- ther involvement of an R&TTE Directive Notified Body for the final product. [Section 2.2.4] The European Compliance Testing listed in Table A-1 was performed using the integral ceramic chip antenna. Advance Information Revision 0.4 12/2015 DS60001372C-Page 57

BM71 Regulatory Compliance Information TABLE A-1: EUROPEAN COMPLIANCE TESTING Certification Standards Article Laboratory Report Number Date Safety EN60950-1:2006/A11:2010/A1:2010/ 10053210 001 - A12:2011/A2:2013 3(1)(a) Health EN62479:2010 10053433 001 - TUV EMC EN301489-1 V1.9.2 3(1)(b) Rheinland 10052964 001 - EN301489-17 V2.2.1 Radio EN300328 V1.9.1 3(2) 10053433 001 - Notified - - - Body A.3.3 HELPFUL WEB SITES • There is an voluntary Electromagnetic Compatibil- ity (EMC) test for the host product administered A document that can be used as a starting point in by VCCI: http://www.vcci.jp/vcci_e/index.html understanding the use of Short Range Devices (SRD) in Europe is the European Radio Communications A.4.1 LABELING AND USER Committee (ERC) Recommendation 70-03 E, which INFORMATION REQUIREMENTS can be downloaded from the European Radio Commu- nications Office (ERO) at: http://www.ero.dk/. Addi- The label on the final product which contains the BM71 tional helpful web sites are: module must follow Japan marking requirements. The integrator of the module should refer to the labeling • Radio and Telecommunications Terminal Equip- requirements for Japan available at the Ministry of ment (R&TTE): Internal Affairs and Communications (MIC) website. http://ec.europa.eu/enterprise/rtte/index_en.htm • European Conference of Postal and Telecommu- The BM71 module is labeled with its own technical con- nications Administrations (CEPT): formity mark and certification number. The final product http://www.cept.org in which this module is being used must have a label attach on the top side of module and another one • European Telecommunications Standards Insti- referring to the type certified module inside: tute (ETSI): http://www.etsi.org • European Radio Communications Office (ERO): http://www.ero.dk • The Radio and Telecommunications Terminal Equipment Compliance Association (R&TTE CA): http://www.rtteca.com A.4.2 HELPFUL WEB SITES A.4 Japan Ministry of Internal Affairs and Communications (MIC): The BM71 module has received type certification and http://www.tele.soumu.go.jp/e/index.htm is labeled with its own technical conformity mark and Association of Radio Industries and Businesses certification number as required to conform to the tech- (ARIB): http://www.arib.or.jp/english/ nical standards regulated by the Ministry of Internal Affairs and Communications (MIC) of Japan pursuant to the Radio Act of Japan. A.5 Korea Integration of this module into a final product does not The BM71 module has received certification of confor- require additional radio certification provided installa- mity in accordance with the Radio Waves Act. Integra- tion instructions are followed and no modifications of tion of this module into a final product does not require the module are allowed. Additional testing may be additional radio certification provided installation required: instructions are followed and no modifications of the • If the host product is subject to electrical appli- module are allowed. ance safety (for example, powered from an AC mains), the host product may require Product Safety Electrical Appliance and Material (PSE) testing. The integrator should contact their confor- mance laboratory to determine if this testing is required. Advance Information Revision 0.4 12/2015 DS60001372C-Page 58

BM71 Regulatory Compliance Information A.5.1 LABELING AND USER 變更原設計 INFORMATION REQUIREMENTS 之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及 干擾合法通信； The label on the final product which contains the BM71 module must follow KC marking requirements. The integrator of the module should refer to the labeling 經發現有干擾現象時，應立即停用，並改善至無干擾時 requirements for Korea available on the Korea Com- 方得繼續使用。 munications Commission (KCC) website. 前項合法通信，指依電信規定作業之無線電信。 The BM71 module due to the limited size(9.0 x 低功率射頻電機須忍受合法通信或工業、科學及醫療用 11.5mm) the KC mark and identifier is displayed in the 電波輻射性 Datasheet only and cannot be displayed on the module label. . 電機設備之干擾。 The final product requires the KC mark and certificate A.6.2 HELPFUL WEB SITES number of the module: National Communications Commission (NCC): http://www.ncc.gov.tw A.7 Other Regulatory Jurisdictions Should other regulatory jurisdiction certification be required by the customer, or the customer need to A.5.2 HELPFUL WEB SITES recertify the module for other reasons, contact Micro- Korea Communications Commission (KCC): chip for the required utilities and documentation. http://www.kcc.go.kr National Radio Research Agency (RRA): http://rra.go.kr A.6 Taiwan The BM71 module has pending compliance approval in accordance with the Telecommunications Act. Custom- ers seeking to use the compliance approval in their product should contact Microchip Technology sales or distribution partners to obtain a Letter of Authority. Integration of this module into a final product does not require additional radio certification provided installa- tion instructions are followed and no modifications of the module are allowed. A.6.1 LABELING AND USER INFORMATION REQUIREMENTS The BM71 module due to the limited size(9.0 x 11.5mm) the NCC mark and identifier is displayed in the Datasheet only and cannot be displayed on the module label : LABEL The user's manual should contain below warning (for RF device) in traditional Chinese: 注意 ! 依據 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許 可， 公司、商號或使用者均不得擅自變更頻率、加大功率或 Advance Information Revision 0.4 12/2015 DS60001372C-Page 59

BM71 Regulatory Compliance Information Appendix B: Labelling Considerations BM71 module, due to the module dimension limitation, could not add the certificate ID on module directly, we would like to apply for your permission to add the certificate ID on the Datasheet and alternatively on the shipping package instead of on module. Description： 1. BM71 Module dimension 2 Area A: 1.5X8.5mm 2 Area B: 7.7X6.1mm , this is a shielding case with a label for BT address and date code 2 Area C: 3.5X8.5mm 2 2 Area D: 2.1X6.35mm and 1.4X3.6mm , the area is not complete and continuous. Form factor 2. According the description above, due to the dimension limitation, we could not find out an area good to print a clear certificate ID or logo. 3. We would apply for your kindly permission to allow Microchip to ship the module by the new approach, in 。 appendix I, to add the certificate ID on the anti-static bag, the out pack of the module tray 4. Appendix B-1 is one of the proposal. Advance Information Revision 0.4 12/2015 DS60001372C-Page 60

BM71 Regulatory Compliance Information Appendix B-1 There is an anti-static bag outside the module tray, we suggest adding the certificate ID on the bag, it is very clear for the custom and government to check the ID, and we will also add the certificate ID information in the module user manual to avoid any possible confusion by the user. Advance Information Revision 0.4 12/2015 DS60001372C-Page 61


Document Created: 2015-12-31 06:12:05
Document Modified: 2015-12-31 06:12:05
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC