Manual

FCC ID: A8TBM70ABCDEFGH

Users Manual

Download: PDF
FCCID_2838611

BM70 Regulatory Compliance Information BM70 Regulatory Compliance Information Revision 0.1 Dec’ 2015 Preliminary Revision 0.1 12/2015 DS60001372C-Page 53

BM70 Regulatory Compliance Information This document covers the Regulatory Compliance information which is part of the BM70 Module datasheet and related documents shared with customers. Preliminary Revision 0.1 12/2015 DS60001372C-Page 54

BM70 Regulatory Compliance Information 1.0 ANTENNA 1.1 Antenna Characteristics 1.1.1 CERAMIC CHIP ANTENNA The BM70 module contains an integral ceramic chip antenna. The Figure 1-1 illustrates the antenna performance of the module. FIGURE 1-1: BM70 ANTENNA RADIATION PATTERN Gain (dBi) 5.0 s Y-ax ax i is 0.0 X- -5.0 -10.0 Z-axis -15.0 -20.0 -25.0 -30.0 -35.0 Frequency 2440 MHz Max Gain 1.63 dBi Efficiency 71.55% Preliminary Revision 0.1 12/2015 DS60001372C-Page 55

BM70 Regulatory Compliance Information APPENDIX A: CERTIFICATION devices, computer peripherals, radio receivers, etc.; and to additional authorization requirements for the NOTICES non-transmitter functions on the transmitter module Note: This device has no been au orized as (i.e., Verification, or Declaration of Conformity) (e.g., required by the rules of the ederal Com- transmitter modules may also contain digital logic func- munications Commission This device is tions) as appropriate. no and may not be, offered or sale or leas or sold or leased, until au orization A.1.2 LABELING AND USER is obtained INFORMATION REQUIREMENTS The BM70 module has been labeled with its own FCC BM70 module regulatory approval status: ID number, and if the FCC ID is not visible when the • BT SIG/QDID:74246 module is installed inside another device, then the out- • United States/FCC ID: A8TBM70ABCDEFGH side of the finished product into which the module is • Canada/IC ID: 12246A-BM70BLES1F2 installed must also display a label referring to the enclosed module. This exterior label can use wording • Europe/CE: In Progress as follows: • Japan/MIC: 202-SMD069 • Korea/KCC: MSIP-CRM-mcp-BM70BLES1FC2 Contains Transmitter Module FCC ID: • Taiwan/NCC No: CCAN15LP0500T1 A8TBM70ABCDEFGH • China/SRRC: in Progress or Contains FCC ID: A8TBM70ABCDEFGH A.1 REGULATORY APPROVAL This device complies with Part 15 of the FCC Rules. This section outlines the regulatory information for the Operation is subject to the following two conditions: BM70 module for the following countries: (1) this device may not cause harmful interference, and (2) this device must accept any interference • United States received, including interference that may cause • Canada undesired operation • Europe A user's manual for the finished product should include • Japan the following statement: • Korea is equipment has been tested and found o comply • Taiwan wi he limi for a Class B digi l device pursuan o • China pa 15 of the FCC Rule These limi s are designed provide reasonable protection agains ha ul A.1.1 UNITED STATES in erence in a residential ins allation. his equip- The BM70 module is in progress to receive Federal ment generate uses and can radiate radio fre- Communications Commission (FCC) CFR47 Telecom- quency energy and if no ins alled and used in munications, Part 15 Subpart C "Intentional Radiators" accordance wi h he in ru ions may cause harmful modular approval in accordance with Part 15.212 Mod- in erence to radio communic ions However ular Transmitter approval. Modular approval allows the ere is no guaran ee hat in nce will not occur end user to integrate the BM70 module into a finished in a par icular in lla ion his equipmen does product without obtaining subsequent and separate cause harmful in nce to radio or television FCC approvals for intentional radiation, provided no recep io which can be determined by urning the changes or modifications are made to the module cir- equipment of and on, the user is encouraged to ry to cuitry. Changes or modifications could void the user's corre the in erence by one or more o the follow- authority to operate the equipment. The end user must ing measures comply with all of the instructions provided by the • Reorien or reloca e he receiving an enn Grantee, which indicate installation and/or operating • ncrease the separation between he equipment conditions necessary for compliance. and receiver The finished product is required to comply with all appli- • Connec he equipmen in an outlet on a circui cable FCC equipment authorizations regulations, di eren from hat which the receiver is con- requirements and equipment functions not associated ne ed. with the transmitter module portion. For example, com- • Consult he dealer or an experienced radio pliance must be demonstrated to regulations for other chnician for help. transmitter components within the host product; to requirements for unintentional radiators (Part 15 Sub- part B "Unintentional Radiators"), such as digital Additional information on labeling and user information requirements for Part 15 devices can be found in KDB Publication 784748 available at the FCC Office of Engi- Preliminary Revision 0.1 12/2015 DS60001372C-Page 54

BM70 Regulatory Compliance Information neering and Technology (OET) Laboratory Division tus shall contain the following or equivalent notice in a Knowledge Database (KDB) conspicuous location in the user manual or alterna- http://apps.fcc.gov/oetcf/kdb/index.cfm. tively on the device or both: A.1.3 RF EXPOSURE is device complies wi ndu Canada license-exem R andard(s) pera ion is sub- All transmitters regulated by FCC must comply with RF je to the ollowing two condi ions (1) this device exposure requirements. KDB 447498 General RF may not cause interferenc and (2) this device mu Exposure Guidance provides guidance in determining accept any interference including in nce h whether proposed or existing transmitting facilities, ay cause undesired operation o the device operations or devices comply with limits for human exposure to Radio Frequency (RF) fields adopted by Le présen appareil es con orme aux CNR d dus- the Federal Communications Commission (FCC). trie Canada applicables aux appareils radio exemp s de licence L'exploi ation es autorisée aux deux con- From the FCC Grant: Output power listed is conducted. ditions suivant (1) l appareil ne doit pas produire This grant is valid only when the module is sold to OEM de brouillage, (2) l'utilisateur de l appareil doit integrators and must be installed by the OEM or OEM accepter out brouillage radioélec rique subi même integrators. This transmitter is restricted for use with si le brouillage es susceptible d'en comprome re le the specific antenna(s) tested in this application for nctionneme Certification and must not be co-located or operating in conjunction with any other antenna or transmitters Transmitter Antenna (from Section 8.3, RSS-Gen, within a host device, except in accordance with FCC Issue 4, November 2014): User manuals for transmit- multi-transmitter product procedures. ters shall display the following notice in a conspicuous location: A.1.4 HELPFUL WEB SITES Under Industry Canada regulations, this radio trans- Federal Communications Commission (FCC): mitter may only operate using an antenna of a type http://www.fcc.gov and maximum (or lesser) gain approved for the trans- FCC Office of Engineering and Technology (OET) Lab- mitter by Industry Canada. To reduce potential radio oratory Division Knowledge Database (KDB): interference to other users, the antenna type and its http://apps.fcc.gov/oetcf/kdb/index.cfm gain should be so chosen that the equivalent isotrop- ically radiated power (e.i.r.p.) is not more than that necessary for successful communication. A.2 Canada Conformément à la réglementation d'Industrie Can- The BM70 module certification is in progress for use in ada, le présent émetteur radio peut fonctionner avec Canada under Industry Canada (IC) Radio Standards une antenne d'un type et d'un gain maximal (ou Specification (RSS) RSS-247 and RSS-Gen. Modular inférieur) approuvé pour l'émetteur par Industrie Can- approval permits the installation of a module in a host ada. Dans le but de réduire les risques de brouillage device without the need to recertify the device. radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que A.2.1 LABELING AND USER la puissance isotrope rayonnée équivalente (p.i.r.e.) INFORMATION REQUIREMENTS ne dépasse pas l'intensité nécessaire à l'établisse- Labeling Requirements for the Host Device (from Sec- ment d'une communication satisfaisante. tion 3.1, RSS-Gen, Issue 4, November 2014): The host The above notice may be affixed to the device instead device shall be properly labeled to identify the module of displayed in the user manual. within the host device. The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to display the Industry Canada certification number of the module, preceded by the words "Contains transmit- ter module", or the word "Contains", or similar wording expressing the same meaning, as follows: Co ains transmitter module User Manual Notice for License-Exempt Radio Appara- tus (from Section 8.4, RSS-Gen, Issue 4, November 2014): User manuals for license-exempt radio appara- Preliminary Revision 0.1 12/2015 DS60001372C-Page 55

BM70 Regulatory Compliance Information A.2.2 RF EXPOSURE Note: o main ain conformance to the testing All transmitters regulated by IC must comply with RF li ed in Table A-1 European Compliance exposure requirements listed in RSS-102 - Radio Fre- es ing the module shall be ins alled in quency (RF) Exposure Compliance of Radio communi- accordance wi the in allation in cation Apparatus (All Frequency Bands). ons in this data sheet and shall no be modified A.2.3 HELPFUL WEB SITES When integra ing a radio module into a Industry Canada: http://www.ic.gc.ca/ comple ed produc he in grator becomes the manuf urer of the final A.3 Europe produ and is therefore responsible for demons ng compliance of the final The BM70 module is in progress to be an R&TTE produ wi h the essen ial requirements of Directive assessed radio module that is CE marked the R&TTE Direc ive and has been manufactured and tested with the inten- tion of being integrated into a final product. A.3.1 LABELING AND USER The BM70 module has been tested to R&TTE Directive INFORMATION REQUIREMENTS 1999/5/EC Essential Requirements for Health and The label on the final product which contains the BM70 Safety (Article (3.1(a)), Electromagnetic Compatibility module must follow CE marking requirements. The (EMC) (Article 3.1(b)), and Radio (Article 3.2) and are R&TTE Compliance Association Technical Guidance summarized in Table A-1. A Notified Body Opinion can Note 01 provides guidance on final product CE mark- be arranged on request. ing. The R&TTE Compliance Association provides guid- ance on modular devices in “Technical Guidance Note A.3.2 ANTENNA REQUIREMENTS 01” document available for download from the following From R&TTE Compliance Association document Tech- location: http://www.rtteca.com/html/down- nical Guidance Note 01. load_area.htm. Provided the integrator installing an assessed radio module with an integral or specific antenna and installed in conformance with the radio mod- ule manufacturer's installation instructions requires no further evaluation.Under Article 3.2 of the R&TTE Directive and does not require fur- ther involvement of an R&TTE Directive Notified Body for the final product. [Section 2.2.4] The European Compliance Testing listed in Table A-1 was performed using the integral ceramic chip antenna. Preliminary Revision 0.1 12/2015 DS60001372C-Page 56

BM70 Regulatory Compliance Information TABLE A-1: EUROPEAN COMPLIANCE TESTING Certification Standards Article Laboratory Report Number Date Safety EN60950-1:2006/A11:2010/A1:2010/ 10051261 002 16.SEP.2015 A12:2011/A2:2013 3(1)(b) Health EN62479:2010 10051445 001 17.May.2015 TUV EMC EN301489-1 V1.9.2 3(1)(b) Rheinland 10051137 001 11.Jun.2015 EN301489-17 V2.2.1 Radio EN300328 V1.9.1 3(2) 10051445 001 17.May.2015 Notified - - - Body A.3.3 HELPFUL WEB SITES • There is an voluntary Electromagnetic Compatibil- ity (EMC) test for the host product administered A document that can be used as a starting point in by VCCI: http://www.vcci.jp/vcci_e/index.html understanding the use of Short Range Devices (SRD) in Europe is the European Radio Communications A.4.1 LABELING AND USER Committee (ERC) Recommendation 70-03 E, which INFORMATION REQUIREMENTS can be downloaded from the European Radio Commu- nications Office (ERO) at: http://www.ero.dk/. Addi- The label on the final product which contains the BM70 tional helpful web sites are: module must follow Japan marking requirements. The integrator of the module should refer to the labeling • Radio and Telecommunications Terminal Equip- requirements for Japan available at the Ministry of ment (R&TTE): Internal Affairs and Communications (MIC) website. http://ec.europa.eu/enterprise/rtte/index_en.htm • European Conference of Postal and Telecommu- The BM70 module is labeled with its own technical con- nications Administrations (CEPT): formity mark and certification number. The final product http://www.cept.org in which this module is being used must have a label attach on the top side of module and another one • European Telecommunications Standards Insti- referring to the type certified module inside: tute (ETSI): http://www.etsi.org • European Radio Communications Office (ERO): http://www.ero.dk • The Radio and Telecommunications Terminal Equipment Compliance Association (R&TTE CA): http://www.rtteca.com A.4.2 HELPFUL WEB SITES A.4 Japan Ministry of Internal Affairs and Communications (MIC): The BM70 module has received type certification and http://www.tele.soumu.go.jp/e/index.htm is labeled with its own technical conformity mark and Association of Radio Industries and Businesses certification number as required to conform to the tech- (ARIB): http://www.arib.or.jp/english/ nical standards regulated by the Ministry of Internal Affairs and Communications (MIC) of Japan pursuant to the Radio Act of Japan. A.5 Korea Integration of this module into a final product does not The BM70 module has received certification of confor- require additional radio certification provided installa- mity in accordance with the Radio Waves Act. Integra- tion instructions are followed and no modifications of tion of this module into a final product does not require the module are allowed. Additional testing may be additional radio certification provided installation required: instructions are followed and no modifications of the • If the host product is subject to electrical appli- module are allowed. ance safety (for example, powered from an AC mains), the host product may require Product Safety Electrical Appliance and Material (PSE) testing. The integrator should contact their confor- mance laboratory to determine if this testing is required. Preliminary Revision 0.1 12/2015 DS60001372C-Page 57

BM70 Regulatory Compliance Information A.5.1 LABELING AND USER 第十四條 低功率射頻電機之使用不得影響飛航安全及 INFORMATION REQUIREMENTS 干擾合法通信； 經發現有干擾現象時，應立即停用，並改善至無干擾時 方得繼續使用。 The label on the final product which contains the BM70 module must follow KC marking requirements. The integrator of the module should refer to the labeling 前項合法通信，指依電信規定作業之無線電信。 requirements for Korea available on the Korea Com- 低功率射頻電機須忍受合法通信或工業、科學及醫療用 munications Commission (KCC) website. 電波輻射性 The BM70 module is labeled with its own KC mark. The final product requires the KC mark and certificate num- 電機設備之干擾。 ber of the module: A.6.2 HELPFUL WEB SITES National Communications Commission (NCC): http://www.ncc.gov.tw A.7 Other Regulatory Jurisdictions Should other regulatory jurisdiction certification be A.5.2 HELPFUL WEB SITES required by the customer, or the customer need to Korea Communications Commission (KCC): recertify the module for other reasons, contact Micro- http://www.kcc.go.kr chip for the required utilities and documentation. National Radio Research Agency (RRA): http://rra.go.kr A.6 Taiwan The BM70 module has pending compliance approval in accordance with the Telecommunications Act. Custom- ers seeking to use the compliance approval in their product should contact Microchip Technology sales or distribution partners to obtain a Letter of Authority. Integration of this module into a final product does not require additional radio certification provided installa- tion instructions are followed and no modifications of the module are allowed. A.6.1 LABELING AND USER INFORMATION REQUIREMENTS The BM70 module is labeled with its own NCC mark and certificate number as below: LABEL The user's manual should contain below warning (for RF device) in traditional Chinese: 注意 ! 依據 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許 可， 公司、商號或使用者均不得擅自變更頻率、加大功率或 變更原設計 之特性及功能。 Preliminary Revision 0.1 12/2015 DS60001372C-Page 58


Document Created: 2015-12-10 23:46:00
Document Modified: 2015-12-10 23:46:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC