FCC Report_15.225 rev1

FCC ID: A4HWS6S2

Test Report

Download: PDF
FCCID_4481928

Oracle America, Inc RF TEST REPORT Report Type: FCC Part 15.225 & RSS-210 RF report Model: MICROS Workstation 6 Series 2 REPORT NUMBER: 190503052SHA-002 ISSUE DATE: Aug 1, 2019 DOCUMENT CONTROL NUMBER: TTRFFCCPART15C_V1 © 2018 Intertek

Intertek Testing Services Shanghai Building No.86, 1198 Qinzhou Road (North) Caohejing Development Zone Shanghai 200233, China Telephone: 86 21 6127 8200 TEST REPORT www.intertek.com Report no.: 190503052SHA-002 Applicant : Oracle America, Inc 500 Oracle Parkway Redwood City, CA 94065 US Manufacturer : Oracle America, Inc 500 Oracle Parkway Redwood City, CA 94065 US Factory : GES Manufacturing Services (M) SDN BHD Plo 34 Fasa 2, Kawasan Perindustrian, Senai 81400, Johor, Malaysia FCC ID : A4HWS6S2 IC : 9870A-WS6S2 SUMMARY: The equipment complies with the requirements according to the following standard(s) or Specification: 47CFR Part 15 (2018): Radio Frequency Devices (Subpart C) RSS-210 (Issue 9): Licence-Exempt Radio Apparatus: Category I Equipment RSS-Gen (Issue 5): General Requirements for Compliance of Radio Apparatus ANSI C63.10 (2013): American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices PREPARED BY: REVIEWED BY: Project Engineer Reviewer Stephanie Zhang Wakeyou Wang This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRFFCCPART15C_V1 © 2018 Intertek Page 2 of 30

Report No.: 190503052SHA-002 TEST REPORT Content REVISION HISTORY................................................................................................................................................ 5 MEASUREMENT RESULT SUMMARY ..................................................................................................................... 6 1 GENERAL INFORMATION ............................................................................................................................. 7 1.1 DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ..................................................................................................... 7 1.2 TECHNICAL SPECIFICATION .................................................................................................................................... 7 1.3 DESCRIPTION OF TEST FACILITY .............................................................................................................................. 8 2 TEST SPECIFICATIONS ................................................................................................................................... 9 2.1 STANDARDS OR SPECIFICATION ............................................................................................................................... 9 2.2 MODE OF OPERATION DURING THE TEST................................................................................................................... 9 2.3 TEST SOFTWARE LIST ............................................................................................................................................ 9 2.4 TEST PERIPHERALS LIST ......................................................................................................................................... 9 2.5 TEST ENVIRONMENT CONDITION:............................................................................................................................ 9 2.6 INSTRUMENT LIST .............................................................................................................................................. 10 2.7 MEASUREMENT UNCERTAINTY ............................................................................................................................. 11 3 FUNDAMENTAL EMISSION ......................................................................................................................... 12 3.1 LIMIT .............................................................................................................................................................. 12 3.2 MEASUREMENT PROCEDURE ............................................................................................................................... 12 3.3 TEST CONFIGURATION ........................................................................................................................................ 13 3.4 TEST RESULTS OF FUNDAMENTAL EMISSIONS .......................................................................................................... 14 4 SPURIOUS EMISSION ................................................................................................................................. 15 4.1 LIMIT .............................................................................................................................................................. 15 4.2 MEASUREMENT PROCEDURE ............................................................................................................................... 15 4.3 TEST CONFIGURATION ........................................................................................................................................ 16 4.4 TEST RESULTS OF RADIATED EMISSIONS ................................................................................................................. 18 5 FREQUENCY STABILITY (TEMPERATURE VARIATION) .................................................................................. 19 5.1 TEST LIMIT ....................................................................................................................................................... 19 5.2 TEST CONFIGURATION ........................................................................................................................................ 19 5.3 TEST PROCEDURE AND TEST SETUP ........................................................................................................................ 19 5.4 TEST PROTOCOL ................................................................................................................................................ 20 6 FREQUENCY STABILITY (VOLTAGE VARIATION) ........................................................................................... 21 6.1 TEST LIMIT ....................................................................................................................................................... 21 6.2 TEST CONFIGURATION ........................................................................................................................................ 21 6.3 TEST PROCEDURE AND TEST SETUP ........................................................................................................................ 21 6.4 TEST PROTOCOL ................................................................................................................................................ 22 7 CONDUCTED EMISSIONS ........................................................................................................................... 23 7.1 LIMIT .............................................................................................................................................................. 23 7.2 TEST CONFIGURATION ........................................................................................................................................ 23 7.3 MEASUREMENT PROCEDURE ............................................................................................................................... 24 7.4 TEST RESULTS OF CONDUCTED EMISSIONS.............................................................................................................. 25 8 99% AND 20DB BANDWIDTH .............................................................................................................. 27 8.1 LIMIT .................................................................................................................................................................. 27 8.2 TEST CONFIGURATION ............................................................................................................................................ 27 8.3 TEST PROCEDURE AND TEST SET UP ........................................................................................................................... 28 8.4 TEST PROTOCOL .................................................................................................................................................... 29 TTRFFCCPART15C_V1 © 2018 Intertek Page 3 of 30

Report No.: 190503052SHA-002 TEST REPORT 9 ANTENNA REQUIREMENT .......................................................................................................................... 30 TTRFFCCPART15C_V1 © 2018 Intertek Page 4 of 30

Report No.: 190503052SHA-002 TEST REPORT Revision History Report No. Version Description Issued Date 190503052SHA-002 Rev. 01 Initial issue of report Aug 1, 2019 TTRFFCCPART15C_V1 © 2018 Intertek Page 5 of 30

Report No.: 190503052SHA-002 TEST REPORT Measurement result summary TEST ITEM FCC REFERANCE IC REFERANCE RESULT Fundamental emission 15.225(a) (b) (c) RSS-210 Annex B.6(a) (b) (c) Pass Spurious emission 15.225(d) RSS-210 Annex B.6(d) Pass Frequency stability 15.225(e) RSS-210 Annex B.6(e) Pass Conducted emissions 15.207 RSS-GEN Clause 8.8 Pass 99% and 20dB Bandwidth 15.215(c) RSS-GEN Clause 6.7 Pass Antenna requirement 15.203 - Pass Notes: 1: NA =Not Applicable 2: Determination of the test conclusion is based on IEC Guide 115 in consideration of measurement uncertainty. TTRFFCCPART15C_V1 © 2018 Intertek Page 6 of 30

Report No.: 190503052SHA-002 TEST REPORT 1 GENERAL INFORMATION 1.1 Description of Equipment Under Test (EUT) Product name: Point of Sale Terminal Type/Model: MICROS Workstation 6 Series 2 There is one model only. The RF function is assessed in this report. There are two optional panels that are electrical identical except for different ports. Both were tested and the worse data is listed in this report. Among this report, an AC/DC adapter was used to power up the EUT, the adaptors information is as below: Model FSP120-AHAN3: Input: AC 100-240V, 50-60Hz, 2A; Output: DC 12V, 10A max. The device supports 802.11a/b/g/n/ac, Bluetooth and RFID functions. Description of EUT: Among this report only 13.56MHz RFID was assessed. Rating: DC 12V-15V, 8.3A; EUT type: Table top Floor standing Software Version: / Hardware Version: / Sample received date: June 14, 2019 Date of test: June 14, 2019 – July 29, 2019 1.2 Technical Specification Frequency Range: 13.56MHz ~ 13.56 MHz TTRFFCCPART15C_V1 © 2018 Intertek Page 7 of 30

Report No.: 190503052SHA-002 TEST REPORT 1.3 Description of Test Facility Name: Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Telephone: 86 21 61278200 Telefax: 86 21 54262353 The test facility is CNAS Accreditation Lab recognized, Registration No. CNAS L0139 certified, or accredited by these FCC Accredited Lab organizations: Designation Number: CN1175 IC Registration Lab Registration code No.: 2042B-1 VCCI Registration Lab Registration No.: R-4243, G-845, C-4723, T-2252 NVLAP Accreditation Lab NVLAP LAB CODE: 200849-0 A2LA Accreditation Lab Certificate Number: 3309.02 TTRFFCCPART15C_V1 © 2018 Intertek Page 8 of 30

Report No.: 190503052SHA-002 TEST REPORT 2 TEST SPECIFICATIONS 2.1 Standards or specification 47CFR Part 15 (2018) RSS-210 (Issue 9) RSS-Gen (Issue 5) ANSI C63.10 (2013) 2.2 Mode of operation during the test While testing, the internal modulation and continuously transmission was applied. 2.3 Test software list Test Items Software Manufacturer Version Conducted emission ESxS-K1 R&S V2.1.0 Radiated emission ES-K1 R&S V1.71 2.4 Test peripherals list Item No Description Band and Model S/No Adapter (12V DC power adaptor 1 from the bottom power FSP120-AHAN3 / connector) 2.5 Test environment condition: Test items Temperature Humidity Radiated emission 26C 56% RH Power line conducted emission 26C 56% RH TTRFFCCPART15C_V1 © 2018 Intertek Page 9 of 30

Report No.: 190503052SHA-002 TEST REPORT 2.6 Instrument list Radiated Emission Used Equipment Manufacturer Type Internal no. Due date Test Receiver R&S ESIB 26 EC 3045 2019-09-12 Bilog Antenna TESEQ CBL 6112D EC 4206 2019-12-10 AFS42- Pre-amplifier R&S 00101800-25-S- EC5262 2020-06-11 42 Horn antenna R&S HF 906 EC 3049 2019-11-16 Horn antenna ETS 3117 EC 4792-1 2020-02-25 Horn antenna TOYO HAP18-26W EC 4792-3 2020-07-09 Active loop Schwarzbeck FMZB1519 EC 5345 2020-03-14 antenna RF test Used Equipment Manufacturer Type Internal no. Due date PXA Signal Analyzer Keysight N9030A EC 5338 2020-03-04 Power sensor Agilent U2021XA EC 5338-1 2020-03-04 Vector Signal Agilent N5182B EC 5175 2020-03-04 Generator Climate chamber GWS MT3065 EC 6021 2020-07-02 Spectrum Analyzer Keysight N9030A EC 6078 2020-6-11 Tet Site Used Equipment Manufacturer Type Internal no. Due date Shielded room Zhongyu - EC 2838 2020-01-13 Shielded room Zhongyu - EC 2839 2020-01-13 Semi-anechoic Albatross - EC 3048 2019-07-31 chamber project Fully-anechoic Albatross - EC 3047 2019-07-31 chamber project Additional instrument Used Equipment Manufacturer Type Internal no. Due date Therom- ZJ1-2A S.M.I.F. EC 3325 2020-04-07 Hygrograph TTRFFCCPART15C_V1 © 2018 Intertek Page 10 of 30

Report No.: 190503052SHA-002 TEST REPORT 2.7 Measurement uncertainty The measurement uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Expanded Uncertainty Measurement Frequency (k=2) 9kHz ~ 150kHz 3.52 dB Conducted emission at mains ports 150kHz ~ 30MHz 3.19 dB Radiated Emissions up to 1 GHz 30MHz ~ 1GHz 4.90 dB 1GHz ~ 6GHz 5.02 dB Radiated Emissions above 1 GHz 6GHz ~ 18GHz 5.28 dB TTRFFCCPART15C_V1 © 2018 Intertek Page 11 of 30

Report No.: 190503052SHA-002 TEST REPORT 3 Fundamental Emission Test result: Pass 3.1 Limit Frequencies Limit at 30m Limit at 3m (MHz) (dBuV/m) (dBuV/m) 13.110 – 13.410 40.50 80.50 13.410 – 13.553 50.50 90.50 13.553 – 13.567 84.00 124.00 13.567 – 13.710 50.50 90.50 13.710 – 14.010 40.50 80.50 3.2 Measurement Procedure a) The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b) The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c) Both X and Y axes of the antenna are set to make the measurement. d) For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e) The test-receiver system was set to PK Detect Function and Specified Bandwidth with Maximum Hold Mode. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9kHz at frequency below 30MHz. TTRFFCCPART15C_V1 © 2018 Intertek Page 12 of 30

Report No.: 190503052SHA-002 TEST REPORT 3.3 Test Configuration EUT& 3m Support Units Turn Table 80cm Test Receiver TTRFFCCPART15C_V1 © 2018 Intertek Page 13 of 30

Report No.: 190503052SHA-002 TEST REPORT 3.4 Test Results of Fundamental Emissions Corrected Antenna Frequency Correct Factor Limit Reading Margin Detector Polarization (MHz) (dB/m) (dBuV/m) (dBuV/m) X 13.56 56.30 20.40 124.00 67.70 PK Y 13.56 43.40 20.40 124.00 80.60 PK Z 13.56 51.80 20.40 124.00 72.20 PK Remark: 1. Correct Factor = Antenna Factor + Cable Loss (+ Amplifier, for higher than 1GHz), the value was added to Original Receiver Reading by the software automatically. 2. Corrected Reading = Original Receiver Reading + Correct Factor 3. Margin = Limit - Corrected Reading Example: Assuming Antenna Factor = 30.20dB/m, Cable Loss = 2.00dB, Gain of Preamplifier = 32.00dB, Original Receiver Reading = 10.00dBuV, Limit = 40.00dBuV/m. Then Correct Factor = 30.20 + 2.00 – 32.00 = 0.20dB/m; Corrected Reading = 10dBuV + 0.20dB/m = 10.20dBuV/m; Margin = 40.00dBuV/m - 10.20dBuV/m = 29.80dB. TTRFFCCPART15C_V1 © 2018 Intertek Page 14 of 30

Report No.: 190503052SHA-002 TEST REPORT 4 Spurious Emission Test result: Pass 4.1 Limit Frequencies Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 4.2 Measurement Procedure For Radiated emission below 30MHz: f) The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. g) The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. h) Both X and Y axes of the antenna are set to make the measurement. i) For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. j) The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. NOTE: 2. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9kHz at frequency below 30MHz. For Radiated emission above 30MHz: a) The EUT was placed on the top of a rotating table 0.8 meters (for 30MHz ~ 1GHz) / 1.5 meters (for above 1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b) The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c) The height of antenna is varied from one meter to four meters above the ground to determine the TTRFFCCPART15C_V1 © 2018 Intertek Page 15 of 30

Report No.: 190503052SHA-002 TEST REPORT maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d) For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e) The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f) The test-receiver system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1GHz. 3. All modes of operation were evaluated and the worst-case emissions were reported 4.3 Test Configuration For Radiated emission below 30MHz: EUT& 3m Support Units Turn Table 80cm Test Receiver TTRFFCCPART15C_V1 © 2018 Intertek Page 16 of 30

Report No.: 190503052SHA-002 TEST REPORT For Radiated emission 30MHz to 1GHz: Ant. Tower 1-4m Variable EUT& 3m Support Units Turn Table 80cm Test Receiver For Radiated emission above 1GHz: Ant. Tower 1-4m Variable EUT& 3m Support Units Turn Table Absorber 150cm Test Receiver TTRFFCCPART15C_V1 © 2018 Intertek Page 17 of 30

Report No.: 190503052SHA-002 TEST REPORT 4.4 Test Results of Radiated Emissions Test data below 30MHz: Corrected Correct Antenna Frequency Limit Reading Factor Margin Detector Remark Polarization (MHz) (dBuV/m) (dBuV/m) (dB/m) X 1.23 46.90 20.20 65.81 18.91 PK Spurious X 1.64 33.80 20.20 63.31 29.51 PK Spurious X 2.42 40.40 20.30 69.50 29.10 PK Spurious Y 1.11 37.60 20.20 66.70 29.10 PK Spurious Y 1.65 34.50 20.20 63.25 28.75 PK Spurious Y 2.06 32.60 20.30 69.50 36.90 PK Spurious Y 7.03 42.90 20.20 69.50 26.60 PK Spurious Z 7.69 41.10 20.20 69.50 28.40 PK Spurious Test data from 30MHz to 1000MHz: Corrected Antenna Frequency Correct Factor Limit Reading Margin Detector Polarization (MHz) (dB/m) (dBuV/m) (dBuV/m) H 162.18 31.70 11.20 43.50 11.80 PK H 189.40 31.10 10.90 43.50 12.40 PK H 325.47 40.50 15.70 46.00 5.50 PK H 352.69 38.80 16.50 46.00 7.20 PK H 597.62 34.00 20.90 46.00 12.00 PK H 815.33 36.10 23.00 46.00 9.90 PK V 78.60 29.40 7.80 43.50 14.10 PK V 86.37 28.30 9.30 43.50 15.20 PK V 127.19 27.10 13.10 43.50 16.40 PK V 409.06 33.90 17.90 46.00 12.10 PK V 696.75 31.10 21.60 46.00 14.90 PK V 792.00 31.10 22.80 46.00 14.90 PK Remark: 1. Correct Factor = Antenna Factor + Cable Loss (+ Amplifier, for higher than 1GHz), the value was added to Original Receiver Reading by the software automatically. 2. Corrected Reading = Original Receiver Reading + Correct Factor 3. Margin = Limit - Corrected Reading 4. If the PK Corrected Reading is lower than AV limit, the AV test can be elided. Example: Assuming Antenna Factor = 30.20dB/m, Cable Loss = 2.00dB, Gain of Preamplifier = 32.00dB, Original Receiver Reading = 10.00dBuV, Limit = 40.00dBuV/m. Then Correct Factor = 30.20 + 2.00 – 32.00 = 0.20dB/m; Corrected Reading = 10dBuV + 0.20dB/m = 10.20dBuV/m; Margin = 40.00dBuV/m - 10.20dBuV/m = 29.80dB. TTRFFCCPART15C_V1 © 2018 Intertek Page 18 of 30

Report No.: 190503052SHA-002 TEST REPORT 5 Frequency Stability (Temperature Variation) Test result: PASS 5.1 Test limit The frequency tolerance of the carrier signal shall be maintained within ±0.01% of the operating frequency over a temperature variation of −20 degrees to +50 degrees C at normal supply voltage. 5.2 Test Configuration Temperature Chamber Receiving antenna EUT Supporting Spectrum Analyzer RF port R F i n p u t 5.3 Test procedure and test setup Test Procedure as per ANSI 63.10 clause 6.8.1. TTRFFCCPART15C_V1 © 2018 Intertek Page 19 of 30

Report No.: 190503052SHA-002 TEST REPORT 5.4 Test protocol Voltage Temp Freq measured Freq nominal Tolerance (%) Limit (V) (ºC) (MHz) (MHz) (%) -20 13.559 0.007 -10 13.559 0.007 0 13.560 0 10 13.560 0 120 13.560 0.01 20 13.560 0 30 13.560 0 40 13.560 0 50 13.559 0.007 TTRFFCCPART15C_V1 © 2018 Intertek Page 20 of 30

Report No.: 190503052SHA-002 TEST REPORT 6 Frequency Stability (Voltage Variation) Test result: PASS 6.1 Test limit The frequency tolerance of the carrier signal shall be maintained within ±0.01% for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees C. For battery operated equipment, the equipment tests shall be performed using a new battery. 6.2 Test Configuration Temperature Chamber Receiving antenna Variable Power Supply EUT Spectrum Analyzer RF port R F i n p u t 6.3 Test procedure and test setup Test Procedure as per ANSI 63.10 clause 6.8.2. TTRFFCCPART15C_V1 © 2018 Intertek Page 21 of 30

Report No.: 190503052SHA-002 TEST REPORT 6.4 Test protocol Temp Voltage Freq Measured Freq nominal Tolerance (%) Limit (ºC) (V) (MHz) (MHz) (%) 120 13.560 0 20 102 13.559 13.560 0.007 0.01 138 13.559 0.007 TTRFFCCPART15C_V1 © 2018 Intertek Page 22 of 30

Report No.: 190503052SHA-002 TEST REPORT 7 Conducted emissions Test result: Pass 7.1 Limit Conducted Emissions Limit (dBuV) Frequency of Emission (MHz) QP AV 0.15-0.5 66 to 56* 56 to 46 * 0.5-5 56 46 5-30 60 50 * Decreases with the logarithm of the frequency. 7.2 Test Configuration EUT Peripheral devices LISN LISN EMI receiver TTRFFCCPART15C_V1 © 2018 Intertek Page 23 of 30

Report No.: 190503052SHA-002 TEST REPORT 7.3 Measurement Procedure Measured levels of ac power-line conducted emission shall be the emission voltages from the voltage probe, where permitted, or across the 50 Ω LISN port (to which the EUT is connected), where permitted, terminated into a 50 Ω measuring instrument. All emission voltage and current measurements shall be made on each current-carrying conductor at the plug end of the EUT power cord by the use of mating plugs and receptacles on the LISN, if used. Equipment shall be tested with power cords that are normally supplied or recommended by the manufacturer and that have electrical and shielding characteristics that are the same as those cords normally supplied or recommended by the manufacturer. For those measurements using a LISN, the 50 Ω measuring port is terminated by a measuring instrument having 50 Ω input impedance. All other ports are terminated in 50 Ω loads. Tabletop devices shall be placed on a platform of nominal size 1 m by 1.5 m, raised 80 cm above the reference ground plane. The vertical conducting plane or wall of an RF-shielded (screened) room shall be located 40 cm to the rear of the EUT. Floor-standing devices shall be placed either directly on the reference ground-plane or on insulating material as described in ANSI C63.4. All other surfaces of tabletop or floor-standing EUTs shall be at least 80 cm from any other grounded conducting surface, including the case or cases of one or more LISNs. The bandwidth of the test receiver is set at 9 kHz. TTRFFCCPART15C_V1 © 2018 Intertek Page 24 of 30

Report No.: 190503052SHA-002 TEST REPORT 7.4 Test Results of Conducted Emissions L-Line TTRFFCCPART15C_V1 © 2018 Intertek Page 25 of 30

Report No.: 190503052SHA-002 TEST REPORT N-Line Remark: 1. Correct Factor = LISN Factor + Cable Loss, the value was added to Original Receiver Reading by the software automatically. 2. Corrected Reading = Original Receiver Reading + Correct Factor 3. Margin = Limit - Corrected Reading 4. If the PK Corrected Reading is lower than AV limit, the AV test can be elided. TTRFFCCPART15C_V1 © 2018 Intertek Page 26 of 30

Report No.: 190503052SHA-002 TEST REPORT 8 99% and 20dB Bandwidth Test result: Pass 8.1 Limit The 20dB bandwidth should be fallen in the allocated operating frequency range. No limit for 99% bandwidth. 8.2 Test configuration EUT Antenna Turn Table Test receiver TTRFFCCPART15C_V1 © 2018 Intertek Page 27 of 30

Report No.: 190503052SHA-002 TEST REPORT 8.3 Test procedure and test set up The measurement was applied in a 3m semi-anechoic chamber. The center of the loop antenna shall be 1 m above the horizontal metal ground plane. The following procedure shall be used for measuring (99 %) power bandwidth: 1. Set center frequency to the nominal EUT channel center frequency. 2. Set RBW = 1 % to 5 % of the OBW 3. Set VBW ≥ 3 · RBW 4. Video averaging is not permitted. Where practical, a sample detection and single sweep mode shall be used. Otherwise, peak detection and max hold mode (until the trace stabilizes) shall be used. 5. Use the 99 % power bandwidth function of the instrument (if available). 6. the 20dB bandwidth is also measured with the same setting. TTRFFCCPART15C_V1 © 2018 Intertek Page 28 of 30

Report No.: 190503052SHA-002 TEST REPORT 8.4 Test protocol Lower point Higher point Bandwidth Allocated bandwidth (MHz) (MHz) (kHz) (MHz) 99% Bandwidth 13.5592 13.5607 1.49 / 20dB Bandwidth 13.5597 13.5601 0.42 13.553 ~ 13.567 TTRFFCCPART15C_V1 © 2018 Intertek Page 29 of 30

Report No.: 190503052SHA-002 TEST REPORT 9 Antenna requirement Requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. Result: EUT uses permanently attached antenna to the intentional radiator, so it can comply with the provisions of this section. *************************************** END ***************************************** TTRFFCCPART15C_V1 © 2018 Intertek Page 30 of 30


Document Created: 2019-10-14 14:57:43
Document Modified: 2019-10-14 14:57:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC