DFS Test Report

FCC ID: A3LSMG977KOR

Test Report

Download: PDF
FCCID_4201061

PCTEST ENGINEERING LABORATORY, INC. 18855 Adams Court, Morgan Hill, CA 95037 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctest.com MEASUREMENT REPORT FCC PART 15.407 DFS Applicant Name: Date of Testing: Samsung Electronics Co., Ltd. 1/16 – 3/14/2019 1000 Sylvan Avenue Test Site/Location: Englewood Cliffs, NJ 07632 PCTEST Lab. Morgan Hill, CA, USA Gyeonggi-do, 16677, Korea Test Report Serial No.: 1M1901160006-07.A3L FCC ID: A3LSMG977KOR APPLICANT: Samsung Electronics Co., Ltd. Application Type: Certification Model: SM-G977N EUT Type: Client Only Device, No Radar Detection Capability Max. RF Output Power: 62.951 mW (17.99 dBm) Conducted (802.11ax UNII Band 2A) 62.951 mW (17.99 dBm) Conducted (802.11ax UNII Band 2C) Frequency Range: 5260 – 5320 MHz (UNII-2A Band) 5500 – 5720 MHz (UNII-2C Band) FCC Classification: Unlicensed National Information Infrastructure (UNII) FCC Rule Part(s): Part 15 Subpart E (15.407) Test Procedure(s): KDB 905462 D02 v02 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in KDB 905462 D02 v02 Compliance Measurement Procedures for Unlicensed-National Information Infrastructure Devices Operating in the 5.25 – 5.35 GHz and 5.47 – 5.725 GHz Bands Incorporating Dynamic Frequency Selection. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

T A B L E O F C O N T E N T S 1.0 INTRODUCTION ............................................................................................................ 3 1.1 SCOPE .............................................................................................................................. 3 1.2 PCTEST TEST LOCATION ............................................................................................... 3 1.3 TEST FACILITY / ACCREDITATIONS .............................................................................. 3 2.0 PRODUCT INFORMATION ............................................................................................ 4 2.1 EQUIPMENT DESCRIPTION ........................................................................................... 4 2.2 DEVICE CAPABILITIES .................................................................................................... 4 2.3 TEST SUPPORT EQUIPMENT ........................................................................................ 5 2.4 MASTER PARAMETERS.................................................................................................. 5 2.5 EMI SUPPRESSION DEVICE(S)/MODIFICATIONS ........................................................ 5 3.0 DESCRIPTION OF TESTS ............................................................................................. 6 3.1 EVALUATION PROCEDURE ............................................................................................ 6 3.2 ENVIRONMENTAL CONDITIONS .................................................................................... 6 4.0 ANTENNA REQUIREMENTS ......................................................................................... 7 5.0 MEASUREMENT UNCERTAINTY.................................................................................. 8 6.0 TEST EQUIPMENT CALIBRATION DATA ..................................................................... 9 7.0 DESCRIPTION OF DYNAMIC FREQUENCY SELECTION TEST ............................... 10 7.1 APPLICABILITY .............................................................................................................. 10 7.2 DFS DETECTION THRESHOLD VALUES ..................................................................... 12 7.3 PARAMETERS OF DFS TEST SIGNALS ....................................................................... 13 7.4 SYSTEM OVERVIEW AND PROCEDURE ..................................................................... 14 7.5 SYSTEM CALIBRATION:................................................................................................ 15 8.0 EUT TEST SETUP........................................................................................................ 18 9.0 TEST RESULTS ........................................................................................................... 19 9.1 SUMMARY ...................................................................................................................... 19 9.2 CHANNEL LOADING ...................................................................................................... 20 9.3 CHANNEL MOVE/ CLOSING TRANSMISSION TIME ................................................... 21 9.4 NON-OCCUPANCY PERIOD ......................................................................................... 22 10.0 CONCLUSION .............................................................................................................. 23 MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

1.0 INTRODUCTION 1.1 Scope This report has been prepared to demonstrate compliance with the requirements for Dynamic Frequency Selection (DFS) as stated in KDB 905462 D02 v02. As of July 20, 2007, all devices operating in the 5250 – 5350 MHz and/or the 5470 – 5725 MHz bands (excluding 5600-5650MHz for ISED Canada) must comply with the DFS requirements. 1.2 PCTEST Test Location These measurement tests were radiated at the PCTEST Engineering Laboratory, Inc. facility located at 18855 Adams Court, Morgan Hill, CA 95037. The measurement facility is compliant with the test site requirements specified in ANSI C63.4-2014 and KDB 414788 D01 v01. 1.3 Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab located in Morgan Hill, CA 95037, U.S.A. • PCTEST is an ISO 17025-2005 accredited test facility under the American Association for Laboratory Accreditation (A2LA) with Certificate number 2041.02 for Specific Absorption Rate (SAR), Hearing Aid Compatibility (HAC) testing, where applicable, and Electromagnetic Compatibility (EMC) testing for FCC and Innovation, Science, and Economic Development Canada rules. • PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC 17065-2012 by A2LA (Certificate number 2041.03) in all scopes of FCC Rules and ISED Standards (RSS). • PCTEST facility is a registered (22831) test laboratory with the site description on file with ISED. MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

2.0 PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the Samsung Portable Handset FCC ID: A3LSMG977KOR. The test data contained in this report pertains only to the emissions due to the EUT’s UNII transmitter. As the EUT does not have radar detection capability it was evaluated as a Client Only Device. All test results reported herein are applicable to the sample selected for testing. Mode of Operation: Master Device Client Device (No radar detection) Client Device with Radar Detection Test Device Serial No.: 9215B, 0210H, 3773B, 0378H, 9212B, 0215B, 8968B 2.2 Device Capabilities This device contains the following capabilities: 850/1900 GSM/GPRS/EDGE, 850/1700/1900 WCDMA/HSPA, Multi-band LTE, 802.11b/g/n/ax WLAN, 802.11a/n/ac/ax UNII, Bluetooth (1x, EDR, LE), NFC, ANT+ Band 1 Band 2A Band 2C Band 3 Ch. Frequency (MHz) Ch. Frequency (MHz) Ch. Frequency (MHz) Ch. Frequency (MHz) 36 5180 52 5260 100 5500 149 5745 : : : : : : : : 42 5210 56 5280 120 5600 157 5785 : : : : : : : : 48 5240 64 5320 144 5720 165 5825 Table 2-1. 802.11a / 802.11n / 802.11ac / 802.11ax (20MHz) Frequency / Channel Operations Band 1 Band 2A Band 2C Band 3 Frequency Frequency Frequency Frequency Ch. (MHz) Ch. (MHz) Ch. (MHz) Ch. (MHz) 38 5190 54 102 5270 5510 151 5755 : : : : : : : : 46 5230 62 118 5310 5590 159 5795 : : 142 5710 Table 2-2. 802.11n / 802.11ac / 802.11ax (40MHz BW) Frequency / Channel Operations Band 1 Band 2A Band 2C Band 3 Ch. Frequency (MHz) Ch. Frequency (MHz) Ch. Frequency (MHz) Ch. Frequency (MHz) 42 5210 58 106 5290 5530 155 5775 : : 138 5690 Table 2-3. 802.11ac / 802.11ax (80MHz BW) Frequency / Channel Operations MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

2.3 Test Support Equipment The following equipment was used in support of the DFS testing. Device Manufacturer Model Description S/N: A1521 Access Point C86PJ5RUFJIR Master Apple MacBook Controller C02P41RZG086 Table 2-4. Test Support Equipment Used 2.4 Master Parameters Parameters of Master: Minimum Antenna Gain 1.4 dBi EIRP Level: >23 dBm Access Point Software Version 7.7.4f0 dev Table 2-5. Parameters of Master 2.5 EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and/or no modifications were made during testing. MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 5 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

3.0 DESCRIPTION OF TESTS 3.1 Evaluation Procedure The measurement procedures described in KDB 905462 D02 v02 were used in the measurement of the EUT. Radiated test methodology was used for the DFS evaluation procedure of the EUT. No deviations to the test procedure and test methods occurred during the evaluation of the EUT. Deviation from measurement procedure……………………………………...……………..........................None 3.2 Environmental Conditions The temperature is controlled within range of 15oC to 35oC. The relative humidity is controlled within range of 10% to 75%. The atmospheric pressure is monitored within the range 86-106kPa (860-1060mbar). MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 6 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

4.0 ANTENNA REQUIREMENTS Excerpt from §15.203 of the FCC Rules/Regulations: “An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section.” • The antennas of the EUT are permanently attached. • There are no provisions for connection to an external antenna. Conclusion: The EUT complies with the requirement of §15.203. MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 7 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

5.0 MEASUREMENT UNCERTAINTY The measurement uncertainties shown below were calculated in accordance with the requirements of ANSI C63.10-2013. All measurement uncertainty values are shown with a coverage factor of k = 2 to indicate a 95% level of confidence. The measurement uncertainty shown below meets or exceeds the UCISPR measurement uncertainty values specified in CISPR 16-4-2 and, thus, can be compared directly to specified limits to determine compliance. Parameter Expanded Uncertainty Time ± 0.02% MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 8 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

6.0 TEST EQUIPMENT CALIBRATION DATA Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Measurements antennas used during testing were calibrated in accordance to the requirements of ANSI C63.5- 2017. Manufacturer Model Description Cal. Date Cal. Interval Cal. Due Date Serial No. Aeroflex 3025C PXI RF Synthesizer 7/25/2018 Biennial 7/25/2020 302570726 Aeroflex 3035C PXI RF Digitizer 7/25/2018 Biennial 7/25/2020 303570427 ETS-Lindgren 3117 Horn Antenna 12/5/2018 Annual 12/5/2019 218555 Rohde & Schwarz ESW44 EMI Test Receiver 11/20/2018 Biennial 11/20/2019 101570 Rohde & Schwarz TC-TA18 Cross Polarized Vivaldi Antenna 11/21/2018 Annual 11/21/2019 101057 Table 6-1. Annual Test Equipment Calibration Schedule Note: For equipment listed above that has a calibration date or calibration due date that falls within the test date range, care was taken to ensure that this equipment was used after the calibration date and before the calibration due date. MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 9 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.0 DESCRIPTION OF DYNAMIC FREQUENCY SELECTION TEST 7.1 Applicability The following table from KDB 905462 D02 v02 lists the applicable requirements for the DFS testing. The device evaluated in this report is considered a client device without radar detection capability. Operational Mode Requirement Client Without Client with Radar Master Radar Detection Detection Non-Occupancy Period Yes Not required Yes DFS Detection Threshold Yes Not required Yes Channel Availability Check Time Yes Not required Not required Uniform Spreading Yes Not required Not required U-NII Detection Bandwidth Yes Not required Yes Table 7-1. DFS Applicability Operational Mode Requirement Client Without Client with Master Radar Detection Radar Detection DFS Detection Threshold Yes Not required Yes Channel Closing Transmission Time Yes Yes Yes Channel Move Time Yes Yes Yes U-NII Detection Bandwidth Yes Not required Yes Client Beacon Test N/A Yes Yes Table 7-2. DFS Applicability During Normal Operation MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 10 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Requirements Per KDB 905462 D02 v02 the following are the requirements for Client Devices: a) A Client Device will not transmit before having received appropriate control signals from a Master Device. b) A Client Device will stop all its transmissions whenever instructed by a Master Device to which it is associated and will meet the Channel Move Time and Channel Closing Transmission Time requirements. The Client Device will not resume any transmissions until it has again received control signals from a Master Device. c) If a Client Device is performing In-Service Monitoring and detects a Radar Waveform above the DFS Detection Threshold, it will inform the Master Device. This is equivalent to the Master Device detecting the Radar Waveform and d) through f) of section 5.1.1 apply. d) Irrespective of Client Device or Master Device detection the Channel Move Time and Channel Closing Transmission Time requirements remain the same. Channel Move Time and Channel Closing Transmission Time requirements are listed in the following table. Parameter Value Non-occupancy period Minimum 30 minutes Channel Availability Check Time 60 seconds 10 seconds Channel Move Time See Note 1. Channel Closing Transmission Time 200 milliseconds + an aggregate of 60 milliseconds over remaining 10 second period. See Note 1 and 2. Minimum 100% of the U- NII 99% U-NII Detection Bandwidth transmission power bandwidth. See Note 3. Note 1: The instant that the Channel Move Time and the Channel Closing Transmission Time begins is as follows: • For the Short Pulse Radar Test Signals this instant is the end of the Burst. • For the Frequency Hopping radar Test Signal, this instant is the end of the last radar Burst generated. • For the Long Pulse Radar Test Signal this instant is the end of the 12 second period defining the Radar Waveform. Note 2: The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the beginning of the Channel Move Time plus any additional intermittent control signals required to facilitate a Channel move (an aggregate of 60 milliseconds) during the remainder of the 10 second period. The aggregate duration of control signals will not count quiet periods in between transmissions. Note 3: During the U-NII Detection Bandwidth detection test, radar type 0 is used and for each frequency step the minimum percentage of detection is 90 percent. Measurements are performed with no data traffic. Table 7-3: DFS Response Requirements MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 11 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.2 DFS Detection Threshold Values The DFS detection thresholds are defined for Master devices and Client Devices with In-service monitoring. These detection thresholds are listed in the following table. Value Maximum Transmit Power (See Notes 1 and 2) ≥ 200 milliwatt -64 dBm < 200 milliwatt -62 dBm Note 1: This is the level at the input of the receiver assuming a 0 dBi receive antenna. Note 2: Throughout these test procedures an additional 1 dB has been added to the amplitude of the test transmission waveforms to account for variations in measurement equipment. This will ensure that the test signal is at or above the detection threshold level to trigger a DFS response. Note 3: For this test, the radiated output power of the Master Unit is greater than 23 dBm. Hence, DFS Detection Threshold Value was set to -64dBm. Table 7-4: Detection Thresholds for Master Devices and Client Devices with Radar Detection MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 12 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.3 Parameters of DFS Test Signals As the EUT is a Client Device with no Radar Detection only one type radar pulse is required for the testing. Radar Pulse type 0 was used in the evaluation of the Client device for the purpose of measuring the Channel Move Time and the Channel Closing Transmission Time. Table 7-5 lists the parameters for the Short Pulse Radar Waveforms. A plot of the Radar Pulse Type 0 used for testing is included in Section 7.5 of this report. Minimum Minimum Radar Pulse Width PRI Percentage of Number of Pulses Number of Type (μsec) (μsec) Successful Trials Detection 0 1 1428 18 See Note 1 See Note 1 Test A: 15 unique PRI values randomly selected from the list 6 1 19.10 of 23 PRI values in Roundup { . 360 π‘ƒπ‘…πΌπœ‡π‘ π‘’π‘ } Table 5a Test B: 15 unique 1 1 60% 30 PRI values randomly selected within the range of 518-3066 μsec, with a minimum increment of 1 μsec, excluding PRI values selected in Test A 2 1-5 150-230 23-29 60% 30 3 6-10 200-500 16-18 60% 30 4 11-20 200-500 12-16 60% 30 Aggregate (Radar Types 1-4) 80% 120 Note 1: Short Pulse Radar Type 0 should be used for the detection bandwidth test, channel move time, and channel closing time tests. Table 7-5: Parameters for Short Pulse Radar Waveforms Minimum Number Minimum Radar Pulse Width Chirp Width PRI Number Percentage of of Pulses Number of Type (μsec) (MHz) (μsec) of Bursts Successful per Burst Trials Detection 5 50 - 100 5 - 20 5 – 20 1-3 8 - 20 80% 30 Table 7-6. Parameters for Long Pulse Radar Waveforms Hopping Minimum Minimum Radar Pulse Width PRI Pulses Hopping Rate Sequence Percentage Number of Type (μsec) (μsec) per Hop (kHz) Length of Successful Trials (msec) Detection 6 1 333 9 0.333 300 70% 30 Table 7-7. Parameters for Frequency Hopping Radar Waveforms MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 13 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.4 System Overview and Procedure KDB 905462 D02 v02 describes a radiated test setup and a conducted test setup. The radiated test setup was used for this testing. Figure 7-1 shows the typical test setup. In Band 2C, one channel selected between 5470 and 5725 MHz was chosen for testing. Radar Signal Master Generator UUT Spectrum (Client) Analyzer Figure 7-1. Radiated Test Setup for DFS 1. The “Aeroflex PXI DFS Radar Simulator and Analyzer Test Suite” is setup to provide a simulated radar pulse at the frequency that the Master and Client are operating. A Type 0 radar pulse was used. 2. The Client Device (EUT) is set up per the diagram in Figure 7-1 and communications between the Master device and the Client is established. 3. The FCC video test file is streamed from the Master to the Client to properly load the network. 4. The “Aeroflex PXI DFS Radar Simulator and Analyzer Test Suite” is set to record and display 12 seconds of time, starting from where the simulated radar is generated. This time domain plot captures any transmissions occurring up to and after 10 seconds. Aggregate time is computed to ensure compliance. (Note: the channel may be different since the Master and Client have changed channels due to the detection of the initial radar pulse.) 5. After the initial radar burst the channel is monitored for 10 minutes to ensure no transmissions or beacons occur. A second monitoring setup is used to verify that the Master and Client have both moved to different channels. MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 14 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.5 System Calibration: Radar pulses that are generated at the PXI RF Synthesizer’s Output Port was injected through the Horn antenna. The Vivaldi antenna was connected by a low loss RF cable to the spectrum analyzer. The offset of the spectrum analyzer was calculated based on the loss of the RF cable and gain of the horn antenna. In the ‘PXI DFS Radar Simulator & Analyzer’ software, a Radar Type 0 was used to measure the threshold level as described in Section 7.2 on the spectrum analyzer. D Figure 7-2. Radar Waveform Calibration MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 15 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Radar Pulse Notes: The radiated plots of the RADAR pulse signals (Type 0) are given below after performing the system calibration as described in Section 7.5. Figure 7-3. 5500MHz – Radar Pulse Type 0 (20MHz) Figure 7-4. 5510MHz – Radar Pulse Type 0 (40MHz) MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 16 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Figure 7-5. 5530MHz – Radar Pulse Type 0 (80MHz) MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 17 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

8.0 EUT TEST SETUP Client is connected to Master (AP) via WLAN network and plays a video test file “6 ½ Magic Hours” in a Server (Laptop). This Server is connected to the Master (AP) via ethernet cable. The Vivaldi antenna is adjusted so that the WLAN traffic level, as displayed on the spectrum analyzer, is at lower amplitude than the radar detection threshold. Horn Ant. Radar Signal Generator Master (PXI RF Synthesizer) Vivaldi Ant. Client Spectrum Analyzer Figure 8-1. Radiated Test Setup MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 18 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

9.0 TEST RESULTS 9.1 Summary Company Name: Samsung Electronics Co., Ltd. FCC ID: A3LSMG977KOR FCC Classification: Unlicensed National Information Infrastructure (UNII) Measured Parameter 40MHz Limit Result Bandwidth (excluding 5600-5650MHz Channel Move Time 4.09s 10 seconds Pass for ISED Canada) 5500 – 5720 MHz UNII –Band 2C 200 ms + < 200ms aggregate of Channel Closing + 8.01 ms 60ms over Pass Transmission Time (aggregate) remaining 10 second period Monitored for 10 No client minutes with no Client beacon test transmission Pass client transmission occurred Table 9-1. Summary of Test Results Notes: 1) The EUT was found to be compliant with the requirements for DFS as required for a Client Device per Part 15.407(h), RSS-247 and KDB 905462 D02 v02. 2) Automated test software was used to measure emissions and capture the corresponding plots necessary to show compliance. The list is given below, • DFS threshold count v1.1 • DFS Radar Simulator and Analyzer v2.8 (Aeroflex Inc.) MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 19 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

9.2 Channel Loading Channel Loading Notes: Per KDB 905462 D02 v02, timing plots are required with calculations demonstrating a minimum channel loading of approximately 17% or greater. For example, you can zero span the spectrum analyzer and approximate the transmission time. Figure 9-1. Band 2C Pulse Width Figure 9-2. Band 2C Period Channel Loading = Pulse Width / Period = Points Over Threshold/ Number of Points= 12813/32001 = 40.04% MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 20 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

9.3 Channel Move/ Closing Transmission Time Result Measured Limit Parameter 20MHz Bandwidth Channel Move 4.09 s 10 seconds Time < 200ms 200 ms + aggregate of Channel Closing + 8.01 ms 60ms over remaining Transmission Time (aggregate) 10 second period Notes: 1. The pulses shown in the plots below have been determined to be from the Master AP. 2. Marker Info and Aggregate time results are shown on the right side of the plots below. Figure 9-3. 5530MHz - Channel Move/ Closing Transmission Time - (40 MHz) MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 21 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

9.4 Non-Occupancy Period Notes: 1. No frequency transmission detected during the Non-Occupancy Period of 10 minutes monitoring. Figure 9-4. 5530MHz - Non-Occupancy Period (10 Minutes) - (40MHz) MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 22 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

10.0 CONCLUSION The data collected relate only to the item(s) tested and show that the Samsung Portable Handset FCC ID: A3LSMG977KOR is in compliance with the DFS requirements for a Client Device without radar detection in accordance with Part 15.407 of the FCC Rules and RSS-247 of the Innovation, Science and Economic Development Canada Rules. MEASUREMENT REPORT Approved by: FCC ID: A3LSMG977KOR (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 23 of 23 1M1901160006-07.A3L 1/16 – 3/14/2019 Portable Handset © 2019 PCTEST Engineering Laboratory, Inc. V 9.0 01/18/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.


Document Created: 2019-08-31 17:01:56
Document Modified: 2019-08-31 17:01:56
Β© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC