SAS Test Report

FCC ID: A3LRT4401-48A

Test Report

Download: PDF
FCCID_4234326

PCTEST ENGINEERING LABORATORY, INC. 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctest.com TEST REPORT DP/CBSD-SAS Interoperability Applicant Name: Date of Testing: Samsung Electronics Co. Ltd. 3/21/2019 – 4/5/2019 129, Samsung-ro, Test Site/Location: Yeongtong-gu, Suwon-si PCTEST Lab. Columbia, MD, USA Gyeonggi-do, 16677, Korea Test Report Serial No.: 1M1902080023-01.A3L FCC ID: A3LRT4401-48A APPLICANT: Samsung Electronics Co. Ltd. Application Type: Certification Model: RT4401-48A EUT Type: LTE Base Station Frequency Range: 3550 – 3700 MHz FCC Classification: Citizens Band Category A and B Devices (CBD) FCC Rule Part(s): Part 96 Test Procedure(s): KDB 940660 D01 v01, WINNF-TS-0122-V1.0.0, CBRSA-TS-9001 V.1.0.0 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in the test procedures listed above. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. MEASUREMENT REPORT Approved by: FCC ID: A3LRT4401-48A (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 12 1M1902080023-01.A3L 03/21/2019 – 04/05/2019 LTE Base Station © 2019 PCTEST Engineering Laboratory, Inc. V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

T A B L E O F C O N T E N T S 1.0 INTRODUCTION.............................................................................................................................. 3 1.1 Scope............................................................................................................................................................... 3 1.2 PCTEST Test Location .................................................................................................................................... 3 1.3 Test Facility / Accreditations ............................................................................................................................ 3 2.0 PRODUCT INFORMATION ............................................................................................................. 4 2.1 Equipment Description ..................................................................................................................................... 4 2.2 Device Capabilities .......................................................................................................................................... 4 2.3 Test Configuration ........................................................................................................................................... 4 2.4 Modifications .................................................................................................................................................... 4 3.0 TEST EQUIPMENT CALIBRATION DATA ...................................................................................... 5 4.0 ENVIRONMENTAL CONDITIONS .................................................................................................. 6 5.0 EVALUATION PROCEDURE .......................................................................................................... 7 6.0 TEST Summary................................................................................................................................ 8 6.1 Summary ......................................................................................................................................................... 8 7.0 RF POWER MEASUREMENTS .................................................................................................... 10 8.0 CONCLUSION ............................................................................................................................... 11 APPENDIX A – TEST LOGS ..................................................................................................................... 12 MEASUREMENT REPORT Approved by: FCC ID: A3LRT4401-48A (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 12 1M1902080023-01.A3L 03/21/2019 – 04/05/2019 LTE Base Station © 2019 PCTEST Engineering Laboratory, Inc. V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

1.0 INTRODUCTION 1.1 Scope Measurement and determination of compliance with the technical rules and regulations of the Federal Communications Commission. 1.2 PCTEST Test Location These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility located at 7185 Oakland Mills Road, Columbia, MD 21046. 1.3 Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab located in Columbia, MD 21046, U.S.A. • PCTEST is a CBRS Alliance (OnGo) Approved Test Lab • PCTEST is a WInnForum Approved Test Lab • PCTEST is an ISO 17025-2005 accredited test facility under the American Association for Laboratory Accreditation (A2LA) with Certificate number 2041.01 for CBRS Alliance Certification Test Plan and WInnForum Conformance and Performance Test Technical Standard. • PCTEST is an ISO 17025-2005 accredited test facility under the American Association for Laboratory Accreditation (A2LA) with Certificate number 2041.01 for Specific Absorption Rate (SAR), Hearing Aid Compatibility (HAC) testing, where applicable, and Electromagnetic Compatibility (EMC) testing for FCC and Innovation, Science, and Economic Development Canada rules. • PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC 17065-2012 by A2LA (Certificate number 2041.03) in all scopes of FCC Rules and ISED Standards (RSS). • PCTEST facility is a registered (2451B) test laboratory with the site description on file with ISED. MEASUREMENT REPORT Approved by: FCC ID: A3LRT4401-48A (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 12 1M1902080023-01.A3L 03/21/2019 – 04/05/2019 LTE Base Station © 2019 PCTEST Engineering Laboratory, Inc. V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

2.0 PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the Samsung LTE Base Station FCC ID: A3LRT4401-48A. The test data contained in this report pertains only to DP/CBSD-SAS interoperability. The EUT is a Domain Proxy. Test Device Serial Number(s): SLS-BR0542EAEX S614C24824 and SLS-BR0542EAEX S6114C24817. 2.2 Device Capabilities This device contains the following capabilities: LTE Band 48 This device supports the following conditional features: Conditional Test Case Definitions Supported C1 Mandatory for UUT which supports multi-step registration message ☒ Mandatory for UUT which supports single-step registration with no CPI- signed data in the registration message. By definition, this is a subset of C2 ☐ Category A devices which determine all registration information, including location, without CPI intervention. Mandatory for UUT which supports single-step registration containing C3 ☐ CPI-signed data in the registration message. Mandatory for UUT which supports C4 ☒ RECEIVED_POWER_WITHOUT_GRANT measurement report type. Mandatory for UUT which supports RECEIVED_POWER_WITH_GRANT C5 ☐ measurement report type. Mandatory for UUT which supports parameter change being made at C6 ☐ the UUT and prior to sending a deregistration Table 2-1. Conditional Features 2.3 Test Configuration The EUT was connected to the SAS Test Harness developed by WINNF WG4-CBSD. The latest version of the SAS Test Harness (V1.0.0.2) provided by CBRS Alliance was used. The SAS Test Harness is synchronized to UTC time. 2.4 Modifications No modifications were made to EUT during testing. MEASUREMENT REPORT Approved by: FCC ID: A3LRT4401-48A (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 12 1M1902080023-01.A3L 03/21/2019 – 04/05/2019 LTE Base Station © 2019 PCTEST Engineering Laboratory, Inc. V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

3.0 TEST EQUIPMENT CALIBRATION DATA Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Table 3-1 Annual Test Equipment Calibration Schedule MEASUREMENT REPORT Approved by: FCC ID: A3LRT4401-48A (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 5 of 12 1M1902080023-01.A3L 03/21/2019 – 04/05/2019 LTE Base Station © 2019 PCTEST Engineering Laboratory, Inc. V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

4.0 ENVIRONMENTAL CONDITIONS The temperature is controlled within range of 15oC to 35oC. The relative humidity is controlled within range of 10% to 75%. The atmospheric pressure is monitored within the range 86-106kPa (860-1060mbar). MEASUREMENT REPORT Approved by: FCC ID: A3LRT4401-48A (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 6 of 12 1M1902080023-01.A3L 03/21/2019 – 04/05/2019 LTE Base Station © 2019 PCTEST Engineering Laboratory, Inc. V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

5.0 EVALUATION PROCEDURE The measurement procedure described in KDB 940660 D01 v01 and WINNF-TS-0122-V1.0.0 was used in the measurement of the EUT. Deviation from measurement procedure…………………………………………….....................................None MEASUREMENT REPORT Approved by: FCC ID: A3LRT4401-48A (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 7 of 12 1M1902080023-01.A3L 03/21/2019 – 04/05/2019 LTE Base Station © 2019 PCTEST Engineering Laboratory, Inc. V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

6.0 TEST SUMMARY 6.1 Summary Company Name: Samsung Electronics Co. Ltd. FCC ID: A3LRT4401-48A Table 6-1. Summary of Test Results KDB940660 FCC Part WInnForum Test D01 Section Test Case Description Section(s) Test Case Result 3.3 a) WINNF.FT.D.REG.2 WINNF.FT.D.REG.9 WINNF.FT.D.REG.11 WINNF.FT.D.REG.13 Confirm that the device will only transmit after it WINNF.FT.D.REG.15 96.39 (c) 1 Pass receives authorization from a SAS WINNF.FT.D.REG.17 WINNF.FT.D.REG.19 WINNF.FT.D.GRA.1 WINNF.FT.C.GRA.2 WINNF.FT.C.HBT.11 WINNF.FT.D.REG.2 Check the device registration and authorization with the WINNF.FT.D.REG.9 SAS – determine if the device behaves appropriately for WINNF.FT.D.REG.11 96.39 (c) 2 successful and unsuccessful registrations. The device WINNF.FT.D.REG.13 Pass should not be transmitting without authorization from WINNF.FT.D.REG.15 the SAS. WINNF.FT.D.REG.17 WINNF.FT.D.REG.19 Confirm that the device changes its operating power 96.39(c)(1) 3 WINNF.FT.D.HBT.2 Pass and/or channel in response to a command from the SAS. Confirm that the device correctly configures based on the 96.39 4 N/A Pass different license classes Confirm that the device transmits at a power level less 96.39(c)(1) 5 than or equal to the maximum power level approved by WINNF.PT.C.HBT Pass the SAS. Confirm that the device transmits with a bandwidth less 96.39(b)(c) 6 WINNF.FT.D.HBT.2 Pass than or equal to the SAS specified bandwidth. Confirm that the device transmits on the SAS specified 96.39(c)(2) 7 WINNF.FT.D.HBT.2 Pass frequency. WINNF.FT.C.HBT.3 WINNF.FT.C.HBT.5 WINNF.FT.C.HBT.6 WINNF.FT.C.HBT.7 Confirm that the device stops transmission in response to WINNF.FT.D.HBT.8 WINNF.FT.C.HBT.10 96.39(c)(2) 8 a command from the SAS, within a period as required by Pass WINNF.FT.D.RLQ.2 Part 96. WINNF.FT.D.RLQ.4 WINNF.FT.D.RLQ.6 WINNF.FT.D.DRG.2 WINNF.FT.D.DRG.4 WINNF.FT.C.DRG.5 MEASUREMENT REPORT Approved by: FCC ID: A3LRT4401-48A (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 8 of 12 1M1902080023-01.A3L 03/21/2019 – 04/05/2019 LTE Base Station © 2019 PCTEST Engineering Laboratory, Inc. V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Table 6-2. Summary of Test Results (continued) Confirm that the device sends measurements data in 96.39 (c) 9 WINNF.FT.D.MES.2 Pass response to the command from the SAS. For devices with geo-location, confirm that it notifies the SAS of a new location when it is beyond the required 96.39(a) 10 N/A N/A distance parameter (±50 m) within the required time frame. Confirm that the device is capable of reporting the signal 96.39 (c) 11 WINNF.FT.D.MES.2 Pass level (measurement data) and frequency to SAS. For a device that operates as a Category A CBSD and then desires to operate as a Category B CBSD (or vice versa), 12 N/A Pass confirm that it re-registers with the SAS for the updated authorization status. When CBSDs communicate through a management 96 E 13 N/A Pass system, confirm compliance with all requirements. When communication between the CBSD and SAS is lost: i) Describe how the CBSD would react if the communications between the device and the SAS is lost. Confirm that the CBSD stops transmission once it loses the link to the SAS. ii) Describe the process for re-establishment of the WINNF.FT.C.HBT.9 96.39 14 Pass communications and confirm that the CBSD acts WINNF.FT.C.HBT.10 accordingly. iii) Confirm power-on restart process for registration (re- registration) occurs as expected. iv) Confirm the process for de-registration occurs as expected. WINNF.FT.C.SCS.1 WINNF.FT.C.SCS.2 KDB940660 D01 96.39(f) SAS and Device Security Requirements WINNF.FT.C.SCS.3 Pass Section 4 WINNF.FT.C.SCS.4 WINNF.FT.C.SCS.5 Notes: • Test cases denoted as “N/A” in the table above are not applicable to the EUT and are either Optional or Conditional per Section 6 of WINNF-TS-0122. • Please see Appendix for test data. MEASUREMENT REPORT Approved by: FCC ID: A3LRT4401-48A (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 9 of 12 1M1902080023-01.A3L 03/21/2019 – 04/05/2019 LTE Base Station © 2019 PCTEST Engineering Laboratory, Inc. V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.0 RF POWER MEASUREMENTS Testing is performed per KDB 971168 D01 and across the transmit dynamic range of 37dBm/MHz to 23dBm/MHz for 20MHz Bandwidth. Per manufacturer, Tx1, Tx2, Tx3, and Tx4 produce correlated signals per KDB 662911 D01. The PSD of each transmitter was measured and summed in linear term. Then the antenna gain was added to yield the maxEIRP. The summed maxEIRP is calculated per the following formula: Summed maxEIRP = ConductedPower(Port1+Port3) + AntGain(Port1+Port3) + ConductedPower(Port2+Port4) + AntGain(Port2+Port4) Table 7-1 RF Output Power Measurements (WINNF.PT.C.HBT.1) MEASUREMENT REPORT Approved by: FCC ID: A3LRT4401-48A (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 10 of 12 1M1902080023-01.A3L 03/21/2019 – 04/05/2019 LTE Base Station © 2019 PCTEST Engineering Laboratory, Inc. V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

8.0 CONCLUSION The data collected relate only to the item(s) tested and show that the Samsung LTE Base Station FCC ID: A3LRT4401-48A has been tested to show compliance with Part 96 and KDB 940660 D01 v01. MEASUREMENT REPORT Approved by: FCC ID: A3LRT4401-48A (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 11 of 12 1M1902080023-01.A3L 03/21/2019 – 04/05/2019 LTE Base Station © 2019 PCTEST Engineering Laboratory, Inc. V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

APPENDIX A – TEST LOGS MEASUREMENT REPORT Approved by: FCC ID: A3LRT4401-48A (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 12 of 12 1M1902080023-01.A3L 03/21/2019 – 04/05/2019 LTE Base Station © 2019 PCTEST Engineering Laboratory, Inc. V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.


Document Created: 2019-04-18 15:54:57
Document Modified: 2019-04-18 15:54:57
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC