Users Manual

FCC ID: A3DCD-3010A

Users Manual

Download: PDF
FCCID_17699

Internal CD-ROM Reader CD-3010 User's Manual ECD3010.PM5 1 98.12.17, 10:23 AM

Laser Safety Information This drive employs a laser. Do not remove the cover or attempt to service this device when connected due to the possibility of eye damage. CAUTION Use of control of adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. This label is located on upper enclosure of this drive. Laser Specification Type : Semiconductor laser GaAlAs Wave length : 760 - 810 nm (at 25˚C) Output : 5 mW ECD3010.PM5 2 98.12.17, 10:23 AM

2 NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. LE PRÉSENT APPAREIL NUMÉRIQUE N’ÉMET PAS DE BRUITS RADIOÉLECTRIQUES DÉPASSANT LES LIMITES APPLICABLES AUX APPAREILS NUMÉRIQUES DE CLASSE B PRESCRITES DANS LE RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE ÉDICTÉ PAR LE MINISTÈRE DES COMMUNICATIONS DU CANADA. CAUTION The user who makes changes or modifications to the unit without the express approval by the manufacturer will void user authority to operate the equipment. ACHTUNG Der arbeitsplatzbezogene Geräuschemissionswert dieses Gerätes beträgt ≤ 70dB (A) nach EN 27779/1991. Notice Only CD-ROM discs carrying the label below can be used with this CD-ROM reader. ECD3010.PM5 3 98.12.17, 10:23 AM

3 HEED THE FOLLOWING Read the operating instructions carefully before using the unit and be sure to use it properly. After reading the instructions, store them in an easily accessible place so they can be consulted whenever necessary. WARNING • Continued use should there be an irregularity (smoke, abnormal smell or sound, etc.) will lead to fires or electric shocks. If there should be an irregularity, immediately turn off the power of the computer on which the unit is installed and request servicing. • Do not disassemble or modify the unit in any way. Doing so will lead to fires or electric shocks. • Make sure that no foreign objects get in the unit, as this will lead to fires or electric shocks. If a foreign object should get in the unit, immediately turn off the power of the computer on which the unit is installed and request servicing. • Do not let fluids get in the unit or let the unit get wet, as this will lead to fires or electric shocks. If fluid should get in the unit, immediately turn off the power of the computer on which the unit is installed and request servicing. • Do not use with any power voltage other than the indicated voltage. Doing so will lead to fires or electric shocks. • Do not store or use the unit in places where it may be subject to shocks or strong vibrations. Doing so will lead to fires or electric shocks. • Do not store or use the unit in places where it may be exposed to chemicals or chemical vapors. Doing so will lead to fires or electric shocks. ECD3010.PM5 4 98.12.17, 10:23 AM

4 CAUTION • When connecting computer equipment, audio equipment, speakers, etc., be sure to read the respective manuals carefully, turn of the power, and follow the connection instructions. Using cords other than the specified cords or extending cords could generate heat and result in burns, etc. • Set the volume to the minimum before turning on the power. Sudden bursts of loud sound could result in hearing impairment. • Do not store or use the unit in extremely hot places or places where the humidity fluctuates greatly. Doing so could lead to fires or electric shocks. • Do not store or use the unit in places exposed to direct sunlight or near equipment that generates heat. Doing so could lead to fires. • Do not place the unit on unsteady tables, slanted surfaces or other unstable surfaces. The unit could fall or tip over, resulting in injury. • Do not store or use the unit in humid or dusty places . Doing so could lead to fires or electric shocks. • Do not store or use the unit with heavy objects or objects that stick out passed the frame on top of it. The object or unit may lose its balance and tip over or fall, resulting in injury. • Do not let stick your hands into the disc insertion slot, as this could cause injury. • Do not use cracked or misshapen discs or discs that have been repaired with adhesives, etc. Discs rotate at high speeds inside the unit. If such discs are used, they may break and fly out, resulting in injury. • Do not look directly at the laser source. Exposing the eyes to the laser beam could result in vision impairment. • When used near a radio or TV, the unit may generate noise in the radio or TV. Also, if there is equipment generating strong magnetic forces nearby, this may generate noise in the unit. • Keep the CD tray closed except when inserting or removing CDs in order to prevent injury from bumping into the CD tray. ECD3010.PM5 5 98.12.17, 10:23 AM

5 Cautions Cleaning To clean the CD-ROM reader, wipe it with a soft, damp cloth, using mild detergent if necessary. Please avoid using solvents such as benzine or paint thinner. This can cause color changes or deformation of the CD- ROM reader. Handling the Disc • Do not touch the data side of the disc (the side of the disc with no label or printing). • Do not apply paper labels or write on any part of the disc, data side or label side. Do not use the disc leaved a mark strip paper labels. • If dust or fingerprints get on the disc, wipe it with a soft cloth from the center to the edge. • Do not use benzine, paint thinner, record cleaner, or static repellent. This can damage the disc. • Do not place the disc in any place where it will be subjected to direct sunlight or high temperatures. ECD3010.PM5 6 98.12.17, 10:23 AM

6 Table of Contents Heed the following Warning ............................................................................. 3 Caution .............................................................................. 4 Cautions Cleaning ............................................................................. 5 Handling the Disc ............................................................... 5 Part Names and Functions Front View .......................................................................... 7 Rear View .......................................................................... 8 Installation Jumper Setting ................................................................... 9 Installing the CD-ROM reader in a host PC ....................... 10 Inserting/Removing a CD Using the CD-ROM Drive Installed Vertically .................... 13 Inserting a CD .................................................................... 14 Removing a CD ................................................................. 14 Emergency Eject ................................................................ 14 Specifications CD-ROM Section ............................................................... 15 Audio Section ..................................................................... 15 Environment ....................................................................... 15 General .............................................................................. 15 ECD3010.PM5 7 98.12.17, 10:23 AM

7 Part Names and Functions Front View 1 2 3 4 5 6 1 Phones Jack This jack is used to connect a set of headphones. Please use headphones with a stereo mini-jack plug. 2 Volume Control This control is used to adjust the headphone volume. NOTE: This control has no effect on the audio output from the LINE OUT connector on the back of the CD-ROM reader. 3 BUSY Indicator This indicator lights umber while data is being read. 4 Tray Panel This panel prevents dust from entering the CD-ROM reader. The CD tray will be ejected when the Load/Eject button is pushed. 5 Emergency Eject Hole Use to remove the disc from the CD-ROM reader if the electrical eject is disabled by software or if power failure occurs. (See page 14 “Emergency Eject” for details.) 6 Load/Eject This button is pressed to eject or retract the CD tray when the power is on. ECD3010.PM5 8 98.12.17, 10:23 AM

8 Rear View 7 8 9 10 7 Line Out Connector This connector is used to connect CD-Audio to an audio board. 8 Jumper Blocks This block of jumper locations sets the configuration for the CD-ROM reader. (See page 9 "Jumper Setting" for details.) 9 I/O BUS Connector This BUS connector is used to control the CD-ROM reader and sent data. Use a flat ribbon cable to connect your adaptor board to the CD-ROM reader. Connect the colored side of the ribbon cable to the side marked with the arrow ( ). (See page 12 for details of this connection.) 10 Power Connector Use this to provide operating power from the host computer. (See page 11 for details of this connection.) ECD3010.PM5 9 98.12.17, 10:23 AM

9 Installation Jumper Setting Factory use only Termination SCSI ID Factory use only Jumper locations 1, 2 and 3 are used to set the SCSI ID. Illustration shows how to install jumpers to set the SCSI ID. ID 0 1 2 3 4 5 6 7 Setting Jumper locations 4 and 6 are used during manufacturing and should not be jumped. Jumper location 5 is used to enable or disable the built-in terminator. The built-in terminator is enabled when the jumper is inserted. (Factory set to termination off.) ECD3010.PM5 10 98.12.17, 10:23 AM

10 Installing the CD-ROM reader in a host PC Note Refer to the guidebook included with your personal computer for instruc- tions on installing the CD-ROM reader. This chapter gives one example of installation. 1. Attach the mounting rails to both the left and right sides of the CD- ROM reader. 2. Turn off the computer, other peripherals and unplug all the cords and cables. Then remove the computer cover, face plate, mounting clips, and keeper bracket. Refer to the Guide to Operations that came with your computer for help with this step. 3. Slide the disk drive out approximately 50 ~ 70mm (2 ~ 3 in.), but do not disconnect the cables. 4. Slide the CD-ROM reader into the computer until it is even with the disk drive. DISK DRIVE CD-ROM READER WITH MOUNTING RAILS ECD3010.PM5 11 98.12.17, 10:23 AM

11 5. Locate a spare power cable in your computer. 6. Connect that power cable to the power connector on the back of the CD-ROM reader. CD-ROM READER POWER CONNECTOR POWER CABLE ECD3010.PM5 12 98.12.17, 10:23 AM

12 7. Connect the I/O BUS connector on the CD-ROM reader and the adaptor board with a 50 pin SCSI cable. Connect the colored stripe side of the cable to the side marked with the arrow ( ). I/O BUS CONNECTOR SCSI CABLE ARROW ADAPTOR BOARD COLORED STRIPE (Pin 1) SCSI CABLE 8. Slide the disk drive and CD-ROM reader into the computer. 9. Replace the mounting clips, keeper bracket, and computer cover. ECD3010.PM5 13 98.12.17, 10:23 AM

13 Inserting/Removing a CD Using the CD-ROM Reader Installed Vertically When using the CD-ROM reader, in the vertical position, load and unload discs as shown on the diagram below. CD-ROM reader installed vertically CD-ROM reader installed vertically (right side) (left side) Caution Only 12cm discs can be used when the CD-ROM reader is installed vertically. Do not place 8cm discs in the tray when using the CD-ROM reader installed in this way. ECD3010.PM5 14 98.12.17, 10:23 AM

14 Inserting a CD 1. Press the Load/Eject button. The CD tray will be ejected. 2. Place the disc in the center of the tray with the label side facing up. 3. Press the Load/Eject button. The CD tray will be retracted. Removing a CD 1. Press the Load/Eject button. The CD tray will be ejected. 2. Remove the disc. 3. Press the Load/Eject button. The CD tray will be retracted. WARNING: Do not forcibly push the CD tray in by hand. Doing so may result in damage. Note: If an eject prohibit command has been received from the computer, the CD tray will not be ejected even if the Load/Eject button is pressed. Emergency Eject The procedure described below can be used to remove a disc from the CD-ROM reader if the Load/Eject button is disabled by software or a power failure occurs. 1. Turn off the power to the computer installed the CD-ROM reader. 2. Insert a steel rod (about 1.3mm in diameter) into the emergency eject hole and push hard. The CD tray is ejected by about 10mm. Pull it all the way open by hand. A stiff paper clip may be used as a steel rod. 65mm (AT LEAST 45mm IN LENGTH) ECD3010.PM5 15 98.12.17, 10:23 AM

15 Specifications CD-ROM Section User Data Capacity ........................ 656M bytes/disc (Mode 1) 748M bytes/disc (Mode 2) Total Number of Blocks ................. 336K blocks/disc (Maximum) User Data Blocks ........................... 2048 bytes/block (Mode 1 and Mode 2, Form 1) 2336 bytes/block (Mode 2) 2328 bytes/block (Mode 2 Form 2) Data Transfer Rate ........................ 2550K bytes/sec (Inner side of the disc) 6000K bytes/sec (Outer side of the disc) Burst Transfer Rate ....................... 20M bytes/sec(Sync) 5M bytes/sec(A Sync) Access Time .................................. 85msec (1/3 Stroke read, average) Hard Error Rate ............................. Below 10-12 (After error correction) Memory Buffer ............................... 256K bytes Photo CDTM Compatibility ............... Multisession Photo CDTM Single session Photo CDTM Audio Section Sampling Frequency ...................... 44.1kHz Quantifying Bit Number .................. 16-bit linear Number of Channels ...................... 2 Frequency Response ..................... 20Hz ~ 20kHz +1 –5dB S/N Ratio ....................................... 80dB (1kHz) Total Harmonic Distortion .............. 0.09% (1kHz) Wow & Flutter ................................ Below measurable limits Output ............................................ 0.75 Volt Environment Ambient conditions for use Temperature ............................ 5 to 45°C Humidity ................................... 30 to 70% (no condensation) Ambient conditions for storage Temperature ............................ -20 to 60°C Humidity ................................... 30 to 90% (no condensation) General Power Supply ................................. 5V 1.2A, 12V 1.0A Dimensions(W x H x D) ................. 14.8 x 4.2 x 20.8cm ....................................................... (5 13/16 x 1 5/8 x 8 1/4 in.) Weight ............................................ 0.93kg ....................................................... (2.05 lbs) Note: Above specifications are subject to change. Photo CD is a trademark of Kodak used under license. ECD3010.PM5 16 98.12.17, 10:23 AM


Document Created: 1998-12-22 15:42:12
Document Modified: 1998-12-22 15:42:12
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC