Test Report

FCC ID: 2AUS2-M72S

Test Report

Download: PDF
FCCID_4504030

Page 1 of 34 Report No.: UNIA19072421FR-01 FCC RADIO TEST REPORT FCC ID: 2AUS2-M72S Product： Bluetooth Headset Trade Name： Qenla Model Name： M72S Qenla SP7, SP6, SP6 Pro, SP8, SP1, SP2, SP3, SP5, SP9, SP10, M11, M7, M7S, M10, M10S, M71, M71S, M72, M73, M73S、M75, M75S, M76S, M77S, M78S, A1, A2, A3, A5, A6, A7, A8, A9, A10, A11, A12, A13, A15, A16, A17, A18, A19, Serial Model： A20, M1, M2, M3, M5, M6, M7, M8, M9, M12, M13, M15, M16, M17, M18, M19, M20, M21, M22, M23, QL1, QL2, QL3, QL5, QL6, QL7, QL8, QL9, QL10, QL11, QL12, QL13, QL15, QL16, QL17, QL18, QL19, QL20, B1, B2, B3, B5, B6, B7, B8, B9, B10, B11, Vislla S1, S2, S3, S5, S6, S7, S8, S9, S10 Report No.：UNIA19072421FR-01 Prepared for Qenla Electronic Technology (DongGuan) Co., Ltd. Qenla Industrial Park, No. 8 Qingfeng Road, Qinghutou Village, Tangxia Town, Dongguan china Prepared by Shenzhen United Testing Technology Co., Ltd. 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bao'an District, Shenzhen, China

Page 2 of 34 Report No.: UNIA19072421FR-01 TEST RESULT CERTIFICATION Applicant’s name.................... : Qenla Electronic Technology (DongGuan) Co., Ltd. Qenla Industrial Park, No. 8 Qingfeng Road, Qinghutou Village, Address...................................... : Tangxia Town, Dongguan china Manufacture's Name.............. : Qenla Electronic Technology (DongGuan) Co., Ltd. Qenla Industrial Park, No. 8 Qingfeng Road, Qinghutou Village, Address...................................... : Tangxia Town, Dongguan china Product description Product name............................... : Bluetooth Headset Trade Mark.................................: Qenla Qenla SP7, SP6, SP6 Pro, SP8, SP1, SP2, SP3, SP5, SP9, SP10, M11, M7, M7S, M10, M10S, M71, M71S, M72, M72S, M73, M73S、 M75, M75S, M76S, M77S, M78S, A1, A2, A3, A5, A6, A7, A8, A9, A10, A11, A12, A13, A15, A16, A17, A18, A19, A20, M1, M2, M3, Model and/or type reference . : M5, M6, M7, M8, M9, M12, M13, M15, M16, M17, M18, M19, M20, M21, M22, M23, QL1, QL2, QL3, QL5, QL6, QL7, QL8, QL9, QL10, QL11, QL12, QL13, QL15, QL16, QL17, QL18, QL19, QL20, B1, B2, B3, B5, B6, B7, B8, B9, B10, B11, Vislla S1, S2, S3, S5, S6, S7, S8, S9, S10 FCC Rules and Regulations Part 15 Subpart C Section 15.247, Standards..................................: ANSI C63.10: 2013 This device described above has been tested by Shenzhen United Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of UNI, this document may be altered or revised by Shenzhen United Testing Technology Co., Ltd., personnel only, and shall be noted in the revision of the document. Date of Test............................................... : Date (s) of performance of tests...............: Oct. 10 ~ 29, 2019 Date of Issue.............................................. : Oct. 30, 2019 Test Result.................................................. : Pass Prepared by: Kahn yang/Editor Reviewer: Sherwin Qian/Supervisor Approved & Authorized Signer: Liuze/Manager

Page 3 of 34 Report No.: UNIA19072421FR-01 Table of Contents Page 1. TEST SUMMARY................................................................................................................... 5 1.1 TEST PROCEDURES AND RESULTS.................................................................................. 5 1.2 TEST FACILITY..........................................................................................................................5 1.3 MEASUREMENT UNCERTAINTY.......................................................................................... 5 2. GENERAL INFORMATION................................................................................................... 6 2.1 GENERAL DESCRIPTION OF EUT....................................................................................... 6 2.2 Carrier Frequency of Channels............................................................................................... 7 2.3 Operation of EUT during testing.............................................................................................. 7 2.4 DESCRIPTION OF TEST SETUP...........................................................................................7 2.5 MEASUREMENT INSTRUMENTS LIST................................................................................8 3. CONDUCTED EMISSIONS TEST.......................................................................................9 3.1 Conducted Power Line Emission Limit.....................................................................................9 3.2 Test Setup..................................................................................................................................... 9 3.3 Test Procedure............................................................................................................................. 9 3.4 Test Result.................................................................................................................................... 9 4. RADIATED EMISSION TEST.............................................................................................12 4.1 Radiation Limit........................................................................................................................... 12 4.2 Test Setup................................................................................................................................... 12 4.3 Test Procedure........................................................................................................................... 13 4.4 Test Result.................................................................................................................................. 13 5. BAND EDGE......................................................................................................................... 18 5.1 Limits........................................................................................................................................... 18 5.2 Test Procedure........................................................................................................................... 18 5.3 Test Result.................................................................................................................................. 18 6. OCCUPIED BANDWIDTH MEASUREMENT.................................................................. 20 6.1 Test Limit..................................................................................................................................... 20 6.2 Test Procedure........................................................................................................................... 20 6.3 Measurement Equipment Used...............................................................................................20 6.4 Test Result.................................................................................................................................. 20 7. POWER SPECTRAL DENSITY TEST..............................................................................22 7.1 Test Limit..................................................................................................................................... 22 7.2 Test Procedure........................................................................................................................... 22 7.3 Measurement Equipment Used...............................................................................................22 7.4 Test Result.................................................................................................................................. 22 8. PEAK OUTPUT POWER TEST......................................................................................... 24

Page 4 of 34 Report No.: UNIA19072421FR-01 Table of Contents Page 8.1 Test Limit..................................................................................................................................... 24 8.2 Test Procedure........................................................................................................................... 24 8.3 Measurement Equipment Used...............................................................................................24 8.4 Test Result.................................................................................................................................. 24 9. CONDUCTED BANDEGE MEASUREMENT.................................................................. 25 9.1 Test Setup................................................................................................................................... 25 9.2 Test Procedure........................................................................................................................... 25 9.3 Limit............................................................................................................................................. 25 9.4 Test Result.................................................................................................................................. 25 10. SPURIOUS RF CONDUCTED EMISSION....................................................................27 10.1 Test Limit...................................................................................................................................27 10.2 Test Procedure.........................................................................................................................27 10.3 Test Setup................................................................................................................................. 27 10.4 Test Result................................................................................................................................ 27 11. ANTENNA REQUIREMENT............................................................................................. 33 12. PHOTOGRAPH OF TEST................................................................................................ 34

Page 5 of 34 Report No.: UNIA19072421FR-01 1. TEST SUMMARY 1.1 TEST PROCEDURES AND RESULTS DESCRIPTION OF TEST RESULT CONDUCTED EMISSIONS TEST COMPLIANT RADIATED EMISSION TEST COMPLIANT BAND EDGE COMPLIANT OCCUPIED BANDWIDTH MEASUREMENT COMPLIANT PEAK OUTPUT POWER COMPLIANT CONDUCTED BANDEGE MEASUREMENT COMPLIANT SPURIOUS RF CONDUCTED EMISSION COMPLIANT ANTENNA REQUIREMENT COMPLIANT 1.2 TEST FACILITY Test Firm : Shenzhen United Testing Technology Co., Ltd. Address : 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bao'an District, Shenzhen, China The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19.The testing quality system of our laboratory meets with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L6494 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:2017 General Requirements) for the Competence of testing Laboratories. Designation Number: CN1227 Test Firm Registration Number: 674885 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. 1.3 MEASUREMENT UNCERTAINTY Measurement Uncertainty Conducted Emission Expanded Uncertainty = 2.23dB, k=2 Radiated emission expanded uncertainty(9kHz-30MHz) = 3.08dB, k=2 Radiated emission expanded uncertainty(30MHz-1000MHz) = 4.42dB, k=2 Radiated emission expanded uncertainty(Above 1GHz) = 4.06dB, k=2

Page 6 of 34 Report No.: UNIA19072421FR-01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment Bluetooth Headset Trade Mark Qenla Model Name M72S Qenla SP7, SP6, SP6 Pro, SP8, SP1, SP2, SP3, SP5, SP9, SP10, M11, M7, M7S, M10, M10S, M71, M71S, M72, M73, M73S、M75, M75S, M76S, M77S, M78S, A1, A2, A3, A5, A6, A7, A8, A9, A10, A11, A12, A13, A15, A16, A17, A18, A19, A20, M1, M2, M3, M5, M6, Serial No. M7, M8, M9, M12, M13, M15, M16, M17, M18, M19, M20, M21, M22, M23, QL1, QL2, QL3, QL5, QL6, QL7, QL8, QL9, QL10, QL11, QL12, QL13, QL15, QL16, QL17, QL18, QL19, QL20, B1, B2, B3, B5, B6, B7, B8, B9, B10, B11, Vislla S1, S2, S3, S5, S6, S7, S8, S9, S10 All models have same circuits diagram, PCB Layout, construction Model Difference and rated power, only different is the model name and Appearance. FCC ID 2AUS2-M72S Antenna Type Chip Antenna Antenna Gain 1dBi Frequency Range 2402-2480MHz Number of Channels 40CH Modulation Type GFSK Power Source DC 5V/1A from Adapter Battery of Charger Box: UFX 902030, 3.7V 480mAh Battery Information Battery of Bluetooth Headset: 501012, 3.7V 0.15Wh(7) Table for auxiliary equipment: Equipment Description Manufacturer Model Serial Number Notebook Lenovo Lenovo G475 GB14477457 Adapter Lenovo SC-41 N/A

Page 7 of 34 Report No.: UNIA19072421FR-01 2.2 Carrier Frequency of Channels Channel List Frequency Frequency Frequency Frequency Channel Channel Channel Channel (MHz) (MHz) (MHz) (MHz) 00 2402 10 2422 20 2442 30 2462 01 2404 11 2424 21 2444 31 2464 02 2406 12 2426 22 2446 32 2466 03 2408 13 2428 23 2448 33 2468 04 2410 14 2430 24 2450 34 2470 05 2412 15 2432 25 2452 35 2472 06 2414 16 2434 26 2454 36 2474 07 2416 17 2436 27 2456 37 2476 08 2418 18 2438 28 2458 38 2478 09 2420 19 2440 29 2460 39 2480 2.3 Operation of EUT during testing Operating Mode The mode is used: Transmitting mode Low Channel: 2402MHz Middle Channel: 2440MHz High Channel: 2480MHz 2.4 DESCRIPTION OF TEST SETUP Operation of EUT during Conducted testing: AC 120V/60Hz EUT Operation of EUT during Radiation testing: AC 120V/60Hz EUT

Page 8 of 34 Report No.: UNIA19072421FR-01 2.5 MEASUREMENT INSTRUMENTS LIST Item Equipment Manufacturer Model No. Serial No. Calibrated until CONDUCTED EMISSIONS TEST 1 AMN Schwarzbeck NNLK8121 8121370 2020.09.06 2 AMN ETS 3810/2 00020199 2020.09.06 EMI TEST 3 Rohde&Schwarz ESCI 101210 2020.09.06 RECEIVER 4 AAN TESEQ T8-Cat6 38888 2020.09.06 RADIATED EMISSION TEST 1 Horn Antenna Sunol DRH-118 A101415 2020.09.06 2 BicoNILog Antenna Sunol JB1 Antenna A090215 2020.09.06 3 PREAMP HP 8449B 3008A00160 2020.09.06 4 PREAMP HP 8447D 2944A07999 2020.09.06 EMI TEST 5 Rohde&Schwarz ESR3 101891 2020.09.06 RECEIVER VECTOR Signal 6 Rohde&Schwarz SMU200A 101521 2020.09.06 Generator 7 Signal Generator Agilent E4421B MY4335105 2020.09.06 8 MXA Signal Analyzer Agilent N9020A MY50510140 2020.09.06 9 MXA Signal Analyzer Agilent N9020A MY51110104 2020.09.06 ANT Tower&Turn 10 Champro EM 1000 60764 2020.09.06 table Controller 11 Anechoic Chamber Taihe Maorui 9m*6m*6m 966A0001 2020.09.06 12 Shielding Room Taihe Maorui 6.4m*4m*3m 643A0001 2020.09.06 13 RF Power sensor DARE RPR3006W 15I00041SNO88 2020.09.06 14 RF Power sensor DARE RPR3006W 15I00041SNO89 2020.09.06 15 RF power divider Anritsu K241B 992289 2020.09.06 Wideband radio 16 Rohde&Schwarz CMW500 154987 2020.09.06 communication tester 17 Biconical antenna Schwarzbeck VHA 9103 91032360 2020.09.06 18 Biconical antenna Schwarzbeck VHA 9103 91032361 2020.09.06 Broadband Hybrid 19 Schwarzbeck VULB9163 VULB9163#958 2020.09.06 Antennas 20 Horn Antenna Schwarzbeck BBHA9120D 9120D-1680 2020.09.06 Active Receive Loop 21 Schwarzbeck FMZB 1919B 00023 2020.09.06 Antenna 22 Horn Antenna Schwarzbeck BBHA 9170 BBHA9170651 2020.09.06 Microwave 23 Broadband Schwarzbeck BBV 9721 100472 2020.09.06 Preamplifier 24 Active Loop Antenna Com-Power AL-130R 10160009 2020.09.06 25 Power Meter KEYSIGHT N1911A MY50520168 2020.09.06 26 Frequency Meter VICTOR VC2000 997406086 2020.09.06 27 DC Power Source HYELEC HY5020E 055161818 2020.09.06 Test software 1 E3 Audix 6.101223a N/A N/A

Page 9 of 34 Report No.: UNIA19072421FR-01 3. CONDUCTED EMISSIONS TEST 3.1 Conducted Power Line Emission Limit For unintentional device, according to § 15.107(a) Line Conducted Emission Limits is as following Maximum RF Line Voltage(dBV) Frequency CLASS A CLASS B (MHz) Q.P. Ave. Q.P. Ave. 0.15~0.50 79 66 66~56* 56~46* 0.50~5.00 73 60 56 46 5.00~30.0 73 60 60 50 * Decreasing linearly with the logarithm of the frequency For intentional device, according to §15.207(a) Line Conducted Emission Limit is same as above table. 3.2 Test Setup 3.3 Test Procedure 1, The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. The EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10. 2, Support equipment, if needed, was placed as per ANSI C63.10. 3, All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10. 4, If a EUT received DC power from the USB Port of Notebook PC, the PC’s adapter received AC120V/60Hz power through a Line Impedance Stabilization Network (LISN) which supplied power source and was grounded to the ground plane. 5, All support equipments received AC power from a second LISN, if any. 6, The EUT test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7, Analyzer / Receiver scanned from 150 KHz to 30MHz for emissions in each of the test modes. 3.4 Test Result Pass Remark: 1. All modes were tested at AC 120V and 240V, only the worst result of AC 120V was reported. 2. All modes of Low, Middle, and High channel were tested, only the worst result of High Channel was reported as below:

Page 10 of 34 Report No.: UNIA19072421FR-01 Temperature: 26℃ Relative Humidity: 48% Test Date: Oct. 25, 2019 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Phase: Line Test Mode: Transmitting mode of GFSK 2480MHz Remark: Factor = Insertion Loss + Cable Loss, Result = Reading + Factor, Margin = Result – Limit.

Page 11 of 34 Report No.: UNIA19072421FR-01 Temperature: 26℃ Relative Humidity: 48% Test Date: Oct. 25, 2019 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Phase: Neutral Test Mode: Transmitting mode of GFSK 2480MHz Remark: Factor = Insertion Loss + Cable Loss, Result = Reading + Factor, Margin = Result – Limit.

Page 12 of 34 Report No.: UNIA19072421FR-01 4. RADIATED EMISSION TEST 4.1 Radiation Limit For unintentional device, according to § 15.109(a), except for Class A digital devices, the field strength of radiated emissions from unintentional radiators at a distance of 3 meters shall not exceed the following values： Frequency Distance Radiated Radiated (MHz) (Meters) (dBμV/m) (μV/m) 30-88 3 40 100 88-216 3 43.5 150 216-960 3 46 200 Above 960 3 54 500 For intentional device, according to § 15.209(a), the general requirement of field strength of radiated emissions from intentional radiators at a distance of 3 meters shall not exceed the above table. 4.2 Test Setup 1. Radiated Emission Test-Up Frequency Below 30MHz 2. Radiated Emission Test-Up Frequency 30MHz~1GHz

Page 13 of 34 Report No.: UNIA19072421FR-01 3. Radiated Emission Test-Up Frequency Above 1GHz 4.3 Test Procedure 1. Below 1GHz measurement the EUT is placed on turntable which is 0.8m above ground plane. And above 1GHz measurement EUT was placed on low permittivity and low tangent turn table which is 1.5m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Repeat above procedures until the measurements for all frequencies are complete. 7. The test frequency range from 9KHz to 25GHz per FCC PART 15.33(a). 8.The distance between test antenna and EUT as following table states: Test Frequency range Test Antenna Type Test Distance 9KHz-30MHz Active Loop Antenna 3 30MHz-1GHz Bilog Antenna 3 1GHz-18GHz Horn Antenna 3 18GHz-25GHz Horn Anternna 1 Note: For battery operated equipment, the equipment tests shall be performed using a new battery. 4.4 Test Result PASS Remark: 1. All the test modes completed for test. The worst case of Radiated Emission is High channel, the test data of this mode was reported. 2. By preliminary testing and verifying three axis (X, Y and Z) position of EUT transmitted status, it was found that “Z axis” position was the worst, and test data recorded in this report. 3. Radiated emission test from 9KHz to 10th harmonic of fundamental was verified, and no emission found except system noise floor in 9KHz to 30MHz and not recorded in this report.

Page 14 of 34 Report No.: UNIA19072421FR-01 Below 1GHz Test Results: Temperature: 22℃ Relative Humidity: 48% Test Date: Oct. 25, 2019 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Polarization: Horizontal Test Mode: Transmitting mode of GFSK 2480MHz Remark: Absolute Level = Reading Level + Factor, Margin = Absolute Level – Limit Factor = Ant. Factor + Cable Loss – Pre-amplifier

Page 15 of 34 Report No.: UNIA19072421FR-01 Temperature: 22℃ Relative Humidity: 48% Test Date: Oct. 25, 2019 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Polarization: Vertical Test Mode: Transmitting mode of GFSK 2480MHz Remark: Absolute Level = Reading Level + Factor, Margin = Absolute Level – Limit Factor = Ant. Factor + Cable Loss – Pre-amplifier Remark： (1) Measuring frequencies from 9 KHz to the 1 GHz, Radiated emission test from 9KHz to 30MHz was verified, and no any emission was found except system noise floor. (2) * denotes emission frequency which appearing within the Restricted Bands specified in provision of 15.205, then the general radiated emission limits in 15.209 apply. (3) The IF bandwidth of EMI Test Receiver between 30MHz to 1GHz was 120KHz, 1 MHz for measuring above 1 GHz, below 30MHz was 10KHz.

Page 16 of 34 Report No.: UNIA19072421FR-01 Above 1 GHz Test Results: CH Low (2402MHz) Horizontal Reading Frequency Factor Emission Level Limits Margin Result Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 2402 113.14 -5.84 107.30 114.00 -6.70 PK 2402 84.05 -5.84 78.21 94.00 -15.79 AV 4804 62.77 -3.64 59.13 74.00 -14.87 PK 4804 52.56 -3.64 48.92 54.00 -5.08 AV 7206 57.04 -0.95 56.09 74.00 -17.91 PK 7206 49.54 -0.95 48.59 54.00 -5.41 AV Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin = Absolute Level – Limit Vertical Reading Frequency Factor Emission Level Limits Margin Result Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 2402 113.28 -5.84 107.44 114.00 -6.56 PK 2402 81.19 -5.84 75.35 94.00 -18.65 AV 4804 62.24 -3.64 58.60 74.00 -15.40 PK 4804 51.33 -3.64 47.69 54.00 -6.31 AV 7206 54.58 -0.95 53.63 74.00 -20.37 PK 7206 48.21 -0.95 47.26 54.00 -6.74 AV Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin = Absolute Level – Limit CH Middle (2440MHz) Horizontal Reading Frequency Factor Emission Level Limits Margin Result Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 2440 111.99 -5.71 106.28 114.00 -7.72 PK 2440 82.34 -5.71 76.63 94.00 -17.37 AV 4880 61.84 -3.51 58.33 74.00 -15.67 PK 4880 50.02 -3.51 46.51 54.00 -7.49 AV 7320 55.17 -0.82 54.35 74.00 -19.65 PK 7320 47.77 -0.82 46.95 54.00 -7.05 AV Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin = Absolute Level – Limit Vertical Reading Frequency Factor Emission Level Limits Margin Result Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 2440 111.75 -5.71 106.04 114.00 -7.96 PK 2440 81.61 -5.71 75.90 94.00 -18.10 AV 4880 61.84 -3.51 58.33 74.00 -15.67 PK 4880 50.22 -3.51 46.71 54.00 -7.29 AV 7320 55.17 -0.82 54.35 74.00 -19.65 PK 7320 47.58 -0.82 46.76 54.00 -7.24 AV Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin = Absolute Level – Limit

Page 17 of 34 Report No.: UNIA19072421FR-01 CH High (2480MHz) Horizontal Reading Frequency Factor Emission Level Limits Margin Result Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 2480 112.58 -5.65 106.93 114.00 -7.07 PK 2480 80.71 -5.65 75.06 94.00 -18.94 AV 4960 58.35 -3.43 54.92 74.00 -19.08 PK 4960 50.11 -3.43 46.68 54.00 -7.32 AV 7440 56.72 -0.75 55.97 74.00 -18.03 PK 7440 45.19 -0.75 44.44 54.00 -9.56 AV Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin = Absolute Level – Limit Vertical Reading Frequency Factor Emission Level Limits Margin Result Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 2480 112.63 -5.65 106.98 114.00 -7.02 PK 2480 80.15 -5.65 74.50 94.00 -19.50 AV 4960 60.22 -3.43 56.79 74.00 -17.21 PK 4960 47.36 -3.43 43.93 54.00 -10.07 AV 7440 56.18 -0.75 55.43 74.00 -18.57 PK 7440 46.07 -0.75 45.32 54.00 -8.68 AV Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin = Absolute Level – Limit Remark： (1) Measuring frequencies from 1 GHz to the 25 GHz. (2) “F” denotes fundamental frequency; “H” denotes spurious frequency. “E” denotes band edge frequency. (3) * denotes emission frequency which appearing within the Restricted Bands specified in provision of 15.205, then the general radiated emission limits in 15.209 apply. (4) Data of measurement within this frequency range shown “--- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. (5) The IF bandwidth of EMI Test Receiver between 30MHz to 1GHz was 120KHz, 1 MHz for measuring above 1 GHz, below 30MHz was 10KHz. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 3MHz for peak measurement with peak detector at frequency above 1GHz. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 10Hz for Average measurement with peak detection at frequency above 1GHz. (6) When the test results of Peak Detected below the limits of Average Detected, the Average Detected is not need completed. For example: Top Channel at Fundamental 73.16dBuV/m(PK Value) <93.98(AV Limit), at harmonic 53.20 dBuV/m(PK Value) <54 dBuV/m(AV Limit), the Average Detected not need to completed. (7) All modes of operation were investigated and the worst-case emissions are reported.

Page 18 of 34 Report No.: UNIA19072421FR-01 5. BAND EDGE 5.1 Limits FCC PART 15.249(d) Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in §15.209, whichever is the lesser attenuation. 5.2 Test Procedure The band edge compliance of RF radiated emission should be measured by following the guidance in ANSI C63.10 with respect to maximizing the emission by rotating the EUT, measuring the emission while the EUT is situated in three orthogonal planes (if appropriate), adjusting the measurement antenna height and polarization etc. Set RBW to 100KHz and VBM to 300KHz to measure the peak field strength and set RBW to 1MHz and VBW to 10Hz to measure the average radiated field strength.The conducted RF band edge was measured by using a spectrum analyzer. Set span wide enough to capture the highest in-band emission and the emission at the band edge. Set RBW to 100 KHz and VBW to 300 KHz, to measure the conducted peak band edge. 5.3 Test Result PASS

Page 19 of 34 Report No.: UNIA19072421FR-01 Radiated Band Edge Test: Operation Mode: TX CH Low (2402MHz) Horizontal Frequency Reading Result Factor Emission Level Limits Margin Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 2310 53.79 -5.81 47.98 74.00 -26.02 PK 2310 / -5.81 / 54.00 / AV 2390 53.38 -5.84 47.54 74.00 -26.46 PK 2390 / -5.84 / 54.00 / AV 2400 52.34 -5.84 46.50 74.00 -27.50 PK 2400 / -5.84 / 54.00 / AV Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Vertical Frequency Reading Result Factor Emission Level Limits Margin Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 2310 52.94 -5.81 47.13 74.00 -26.87 PK 2310 / -5.81 / 54.00 / AV 2390 53.63 -5.84 47.79 74.00 -26.21 PK 2390 / -5.84 / 54.00 / AV 2400 52.81 -5.84 46.97 74.00 -27.03 PK 2400 / -5.84 / 54.00 / AV Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Operation Mode: TX CH High (2480MHz) Horizontal Frequency Reading Result Factor Emission Level Limits Margin Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 2483.5 53.19 -5.65 47.54 74.00 -26.46 PK 2483.5 / -5.65 / 54.00 / AV 2500 53.27 -5.72 47.55 74.00 -26.45 PK 2500 / -5.72 / 54.00 / AV Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Vertical: Frequency Reading Result Factor Emission Level Limits Margin Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 2483.5 53.31 -5.65 47.66 74.00 -26.34 PK 2483.5 / -5.65 / 54.00 / AV 2500 52.46 -5.72 46.74 74.00 -27.26 PK 2500 / -5.72 / 54.00 / AV Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier.

Page 20 of 34 Report No.: UNIA19072421FR-01 6. OCCUPIED BANDWIDTH MEASUREMENT 6.1 Test Limit FCC Part15(15.247), Subpart C Frequency Range Section Test Item Limit Result (MHz) >= 500KHz 15.247(a)(2) Bandwidth 2400-2483.5 PASS (6dB bandwidth) 6.2 Test Procedure 1. The EUT was placed on a turn table which is 0.8m above ground plane. 2. Set EUT as normal operation. 3. Based on FCC Part15 C Section 15.247: RBW=100KHz, VBW=300KHz. 4. The useful radiated emission from the EUT was detected by the spectrum analyzer with peak detector. 6.3 Measurement Equipment Used Same as Radiated Emission Measurement 6.4 Test Result PASS Frequency 6dB Bandwidth Result (MHz) (MHz) 2402 0.689 PASS 2440 0.693 PASS 2480 0.696 PASS CH: 2402MHz

Page 21 of 34 Report No.: UNIA19072421FR-01 CH: 2440MHz CH: 2480MHz

Page 22 of 34 Report No.: UNIA19072421FR-01 7. POWER SPECTRAL DENSITY TEST 7.1 Test Limit FCC Part15(15.247), Subpart C Frequency Range Section Test Item Limit Result (MHz) Power Spectral 8 dBm 15.247 2400-2483.5 PASS Density (in any 3KHz) 7.2 Test Procedure 1. The EUT was placed on a turn table which is 0.8m above ground plane. 2. Set EUT as normal operation. 3. Based on FCC Part15 C Section 15.247: RBW=3KHz, VBW=10KHz. 4. The useful radiated emission from the EUT was detected by the spectrum analyzer with peak detector. 7.3 Measurement Equipment Used Same as Radiated Emission Measurement 7.4 Test Result PASS Type Channel Power Spectral Density Limit (dBm/3KHz) Result 0 -7.564 GFSK 19 -7.877 8.00 Pass 39 -8.008 CH: 2402MHz

Page 23 of 34 Report No.: UNIA19072421FR-01 CH: 2440MHz CH: 2480MHz

Page 24 of 34 Report No.: UNIA19072421FR-01 8. PEAK OUTPUT POWER TEST 8.1 Test Limit FCC Part15(15.247), Subpart C Frequency Range Section Test Item Limit Result (MHz) Peak Output 15.247(b)(3) 1 watt or 30dBm 2400-2483.5 PASS Power 8.2 Test Procedure 1. The EUT was placed on a turn table which is 0.8m above ground plane. 2. The EUT was directly connected to the Power meter. 8.3 Measurement Equipment Used Same as Radiated Emission Measurement. 8.4 Test Result PASS Peak Output Type Channel Limit (dBm) Result power (dBm) 0 1.641 GFSK 19 1.624 30 Pass 39 1.752

Page 25 of 34 Report No.: UNIA19072421FR-01 9. CONDUCTED BANDEGE MEASUREMENT 9.1 Test Setup EUT SPECTRUM ANALYZER 9.2 Test Procedure 1. The EUT was placed on a turn table which is 0.8m above ground plane. 2. Set EUT as TX operation and connect directly to the spectrum analyzer. 3. Based on FCC Part15 C Section 15.247: RBW=100KHz, VBW=300KHz. 4. Set detected by the spectrum analyzer with peak detector. 9.3 Limit In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20dB. 9.4 Test Result PASS

Page 26 of 34 Report No.: UNIA19072421FR-01 ＞Limit Frequency Band Delta Peak to band emission(dBc) Result (dBc) Left-band 56.388 20 Pass Right-band 70.18 20 Pass

Page 27 of 34 Report No.: UNIA19072421FR-01 10. SPURIOUS RF CONDUCTED EMISSION 10.1 Test Limit 1. Below -20dB of the highest emission level in operating band. 2. Fall in the restricted bands listed in section 15.205. The maximum permitted average field strength is listed in section 15.209. 3.For below 30MHz,For 9KHz-150kHz,150K-10MHz,We use the RBW 1KHz,10KHz, So the limit need to calculated by “10lg(BW1/BW2)“. for example For9KHz-150kHz,RBW 1KHz, The Limit= the highest emission level-20-10log(100/1)= the highest emission level-40. 10.2 Test Procedure The Spurious RF conducted emissions compliance of RF radiated emission should be measured by following the guidance in ANSI C63.10-2013, For 9KHz-150kHz, Set RBW=1kHz and VBW= 3KHz; For 150KHz-10MHz, Set RBW=10kHz and VBW= 30KHz:For 10MHz-25GHz ,Set RBW=100kHz and VBW= 300KHz in order to measure the peak field strength, and mwasure frequeny range from 9KHz to 25GHz. 10.3 Test Setup 10.4 Test Result PASS

Page 28 of 34 Report No.: UNIA19072421FR-01 CH: 2402MHz 30MHz~3GHz

Page 29 of 34 Report No.: UNIA19072421FR-01 3GHz~25GHz CH: 2440MHz

Page 30 of 34 Report No.: UNIA19072421FR-01 30MHz~3GHz 3GHz~25GHz

Page 31 of 34 Report No.: UNIA19072421FR-01 CH: 2480MHz 30MHz~3GHz

Page 32 of 34 Report No.: UNIA19072421FR-01 3GHz~25GHz

Page 33 of 34 Report No.: UNIA19072421FR-01 11. ANTENNA REQUIREMENT Standard Applicable: For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. Antenna Connected Construction The antenna used in this product is an Internal Antenna, The directional gains of antenna used for transmitting is 1dBi. BT ANTENNA:

Page 34 of 34 Report No.: UNIA19072421FR-01 12. PHOTOGRAPH OF TEST Radiated Emission (Below 1G) Radiated Emission (Above 1G) Conducted Emission ***End of Report***


Document Created: 2019-11-01 18:21:01
Document Modified: 2019-11-01 18:21:01
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC