User manual

FCC ID: 2ATHG-IC1

Users Manual

Download: PDF
FCCID_4358109

User manual WERET Wireless Charger IC-1 V 1.0 EN

Safety Read these simple guidelines. Not following them may be dangerous or illegal. INTERFERENCE All wireless devices may be susceptible to interference, which could affect performance. QUALIFIED SERVICE Only qualified personnel may install or repair this product. BATTERIES, CHARGERS, AND OTHER ACCESSORIES Use only batteries, watch , and other accessories approved by WERET for use with this device. Do not connect incompatible products. KEEP YOUR DEVICE DRY Your device is not water-resistant. Keep it dry. About your wireless charger With the Wireless Charger IC1, you can charge the battery of your WERET Watch without connecting any cables to your watch. The wireless charger is compatible with WPC - Qi V1.2.3 standards. Smart features, such as alerts on foreign object detection are also included in the charger. For more info on operation and safety, see the user guide of your watch or other device.

All parts USB cable Charging Area Indicator light 1 USB connector 2 Charging area for charging the watch 3 Charging and notification indicator light

Charge your WERET watch 1. Connect the charging plate to a USB outlet using the charger provided in the sales box. 2. Make sure the charging plate is facing up, and that there's nothing on the plate. 3. Place your watch in the center of the charging plate. When the indicator light turns to green, the battery is fully charged.

It's normal for the charging plate and device to get warm. . Indicator lights Blue and continuous Charging Green and continuous Standby/the battery of your watch is fully charged Green and flashing Over temperature error, let the watch and charger cool down. The charger stops charging if it reaches

44'C Blue and flashing Charging error, the connected power source is not able to provide enough power If there is a problem with charging: • Check that no other object is on the plate. • If the charging plate is too warm, take your watch off the plate, and unplug the plate. The plate may switch off automatically if it is too hot. When the plate has cooled down, try charging again. • Use the charger provided in the sales box.

FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. RF warning statement: The device has been evaluated to meet general RF exposure requirement.

IC Warning - English: " This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. - French:" Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement." Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power (e.i.r.p.) is not more than that necessary for successful communication.


Document Created: 2019-07-16 11:40:25
Document Modified: 2019-07-16 11:40:25
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC