User Manual

FCC ID: 2AT27-GAN-3X3

Users Manual

Download: PDF
FCCID_4382995

i i i i i ACCESSORIES GETTING STARTED i i i 1. Put the cube in the charging stand, WHITE SIDE UP ONLY. Connect the i i charging stand to power as follows. Thank you for selecting GAN3>3 1 i Springs set x 2 VIP Card x 1 C i C__ i &e =[ _ : eI \ ___J | GAN3x3 x1 Charging stand x 1 USB cable x 1 GAN Bag x 1 c USB cabi c a . onnect to cable onnect to adapter Read carefully before getting started 1 1 i i 1. The product contains built—in motion tracking system. i SPECIFICATIONS |. 2. Shake five times aftercharging | 3. Download and install APP Sides of the cube is NOT alterable. i l 10min to wake up the cube. "Cube Station" and connect 2. "Shake"five times to awake the cube; i Model GAN3x3 Product size B6x86x56mm / 1 the cube per instructions in the GAN3x3 Turn white sidefive times clockwise to disconnect APP. 200 . : i — Product weight ~ 769 Battery type uo. 3.7V lithium : | \ \ i 1 APP. 3. White side up only for charging. i i I {i Charging interval 2.5h Battery endurance Sh 1i $1 i USB adapter SV 500mA Connection Wireless ; } t i | 4 Device requirement IO8 9.0 Android 4.4 or above P \5 i i i Keep manual well for future reference 1 |_ * Battery level will show in APP onceconnected i i i i i 1 1 TENSION ADJUSTMENT MUST KNOWS i i TROUBLE—SHOOTING i 1. Open the center cap. Connecting to APP i 1. Failure of detecting the cube by APP? i 2. Loosen the tension nut: press the tension nut to the bottom, turn the i * Fully charge the cube before connecting. i D Ensure the cube has been fully charged. nut cap to position and release to open the nut cap. Release slowly * Install "Cube Station" APP and connect the cube perinstructions in the i i @ Ensure the cube has been awaken. Once disconnected from APP, to prevent spring from popping out. APP. Once connected, the APP will be able to track GAN356 i‘s motion. i the cube shuts down in 30 seconds automatically. 3. Change the spring: swap in the new spring, put on the nut cap from @ i i @® Ensure the cube has not been connected already by another device. position, push and turn to desired position (0.6/0.8 positions}. Usage restrictions i i @ Android users please ensure "location access" has been authorized 4. Repeat on other sides. * GAN3x3 contains electronic components. DO NOT dismantle the core i to the APP. 1 to damage it. 1 Center cap 1 * DO NOT lube the cube from yellow side. 2. Cube position not synchronized in the APP? i Follow GANCUBE on Instagram . [##] Nut cap * DO NOT crash the product, avoid from water or high temperature (260°C). i D Reset the cube via "Reset Cube" functions in the APP. Tension nut | i for more speedcubing stuff hre o g(RGccsecorecnccccne Spring * Product Contains small parts. NOT suitable for children under 3Gmonths. i @ Cube shuts down when battery is low. Charge timely. * Strictly follow manual to avoid product damage or bodily harm. 1 i @ Gyroscope will accumulate detection bias overtime. This is not Core foot 1 maifunction. Please adjust cube position in APP from time to time i Battery and Charging 1 to ensure synchronization. i * Use the charger and USB cable provided for charging only. Ensure good i 1 3. Failure of charging the cube? conditions of them before connecting to power. i * Product shuts down automatically when battery is low. Please charge the i i ) Ensure sides have not been altered from ex—factory positions. cubetimely to avoid loss of data. i 1 @ When battery is too low, it takes a few minutes to reach minimum * Fully charge the cube at least once every 3 months toavoid permanent i wake—up battery level. GNGANCUBE Warning: DO NOT alter the positionsof center caps, or will lead to synchronization problems. battery damage. Keep in dry and cool conditions if not in use. ‘ |_ More info & supports: support@gancube.com i i

FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.


Document Created: 2019-07-30 19:16:50
Document Modified: 2019-07-30 19:16:50
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC