RF exposure evaluation

FCC ID: 2ASOLSE-ND201PT

RF Exposure Info

Download: PDF
FCCID_4208369

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2ASOLSE-ND201PT Maximum Permissible Exposure Report 1. Product Information FCC ID: 2ASOLSE-ND201PT Product name Wi-fi Camera SE-NA203SW,SE-ND101E, SE-ND101EV, SE-ND201D, SE-ND101M, SE-ND101A2, SE-ND201A2, SE-ND201PG, SE-ND132VR, SE-ND302VR, List Model SE-ND109WD, SE-ND131X, SE-ND101MY, SE-ND131G, SE-ND201PR, SE-ND132E, SE-ND302E, SE-VD102W2, SE-ND201Y, SE-ND301Y, SE-ND201Z, SE-ND301Z, SE-ND501Z Power supply DC 5.0V/2000mA by Adapter Model: BY-U1-5020 Adapter Input: AC 100-240V,50/60Hz,0.3A max Output: DC 5.0V/2000mA IEEE 802.11b: DSSS (CCK,DQPSK,DBPSK) IEEE 802.11g: OFDM (64QAM, 16QAM, QPSK, BPSK) Modulation Type IEEE 802.11n HT20: OFDM (64QAM, 16QAM, QPSK,BPSK) IEEE 802.11n HT40: OFDM (64QAM, 16QAM, QPSK,BPSK) Antenna Type Internal Antenna Antenna Gain 3.00 dBi (maximum) Hardware Version -/- Software Version -/- IEEE 802.11b: 2412 – 2462 MHz IEEE 802.11g: 2412 – 2462 MHz WLAN work frequency IEEE 802.11n HT20: 2412 – 2462 MHz IEEE 802.11n HT40: 2422 – 2452 MHz Exposure category General population/uncontrolled environment EUT Type Production Unit Device Type Mobile Device PCB board, structure and internal of these model(s) are the same, So Model Declaration no additional models were tested. 2. Evaluation Method Systems operating under the provisions of FCC 47 CFR section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as mobile device whereby a distance of 0.2m normally can be maintained between the user and the device, and below RF Permissible Exposure limit shall comply with. In accordance with KDB447498D01 for Simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on the calculated/estimated, numerically modelled or measured field strengths or power density, is ≤ 1.0. The MPE ratio of each antenna is determined at the minimum test separation distance required by the operating configurations and exposure conditions of the host device, according to the ratio of field strengths or power density to MPE limit, at the test frequency. Either the maximum peak or spatially averaged results from measurements or numerical simulations may be used to determine the MPE ratios. Spatial averaging does not apply when MPE is estimated using simple calculations based on far-field plane-wave equivalent conditions. The antenna installation and operating requirements for the host device must meet the minimum test separation distances required by all antennas, in both standalone and simultaneous transmission operations, to satisfy compliance. 3. Limit 3.1 Refer Evaluation Method ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB publication 447498 D01 General 1 RF Exposure Guidance v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1091: Radiofrequency radiation exposure evaluation: mobile devices This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 3

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2ASOLSE-ND201PT 3.2 Limit Limits for Maximum Permissible Exposure (MPE)/Controlled Exposure Frequency Electric Field Magnetic Field Power Density Averaging Time Range(MHz) Strength(V/m) Strength(A/m) (mW/cm²) (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 614 1.63 (100) * 6 3.0 – 30 1842/f 4.89/f (900/f2)* 6 30 – 300 61.4 0.163 1.0 6 300 – 1500 / / f/300 6 1500 – 100,000 / / 5 6 Limits for Maximum Permissible Exposure (MPE)/Uncontrolled Exposure Frequency Electric Field Magnetic Field Power Density Averaging Time Range(MHz) Strength(V/m) Strength(A/m) (mW/cm²) (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 614 1.63 (100) * 30 3.0 – 30 824/f 2.19/f (180/f2)* 30 30 – 300 27.5 0.073 0.2 30 300 – 1500 / / f/1500 30 1500 – 100,000 / / 1.0 30 F=frequency in MHz *=Plane-wave equivalent power density 4. MPE Calculation Method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 5. Antenna Information SE-NA203SW can only use antennas certificated as follows provided by manufacturer; Internal Antenna type and Operate frequency band Maximum antenna gain Identification antenna number Antenna 0 Internal Antenna 2000 MHz – 2500 MHz 3 dBi 6. Conducted Power [2G4WLAN] Frequency Measured Peak Output Power Test Mode Channel (MHz) (dBm) 1 2412 10.32 IEEE 802.11b 6 2437 9.98 11 2462 8.57 1 2412 8.59 IEEE 802.11g 6 2437 8.67 11 2462 8.86 1 2412 8.58 IEEE 802.11n HT20 6 2437 8.55 11 2462 8.09 3 2422 10.39 IEEE 802.11n HT40 6 2437 9.45 9 2452 8.69 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 2 of 3

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2ASOLSE-ND201PT 7. Manufacturing Tolerance [2G4WLAN] IEEE 802.11b (Peak) Channel Channel 1 Channel 6 Channel 11 Target (dBm) 11.0 10.0 9.0 Tolerance ±(dB) 1.0 1.0 1.0 IEEE 802.11g (Peak) Channel Channel 1 Channel 6 Channel 11 Target (dBm) 9.0 9.0 9.0 Tolerance ±(dB) 1.0 1.0 1.0 IEEE 802.11n HT20 (Peak) Channel Channel 1 Channel 6 Channel 11 Target (dBm) 9.0 9.0 9.0 Tolerance ±(dB) 1.0 1.0 1.0 IEEE 802.11n HT40 (Peak) Channel Channel 3 Channel 6 Channel 9 Target (dBm) 11.0 10.0 9.0 Tolerance ±(dB) 1.0 1.0 1.0 8. Measurement Results 8.1 Standalone MPE Evaluation As declared by the Applicant, the EUT is a wireless device used in a fix application, at least 20 cm from any body part of the user or nearby persons; from the maximum EUT RF output power, the minimum separation distance, r =20cm, as well as the gain of the used antenna refer to antenna information, the RF power density can be obtained. [Antenna 0] Output power Antenna Antenna MPE Duty MPE Band/Mode Gain Gain Limits dBm mW Cycle (mW/cm2) (dBi) (linear) (mW/cm2) IEEE 802.11b 12.00 15.8489 3.00 1.9953 100% 0.0063 1.0000 IEEE 802.11g 10.00 10.0000 3.00 1.9953 100% 0.0040 1.0000 IEEE 802.11n HT20 10.00 10.0000 3.00 1.9953 100% 0.0040 1.0000 IEEE 802.11n HT40 12.00 15.8489 3.00 1.9953 100% 0.0063 1.0000 Remark: 1. Output power including tune-up tolerance; 2. MPE evaluate distance is 20cm from user manual provide by manufacturer; 8.2 Simultaneous Transmission MPE This device only support WLAN modular and one antenna, no need consider simultaneous transmit. 9. Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1091 for the uncontrolled RF Exposure of mobile device. ----------------THE END OF REPORT--------------- This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 3 of 3


Document Created: 2019-03-18 16:41:34
Document Modified: 2019-03-18 16:41:34
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC